Avvia una sessione live e installa smartmontools:
Codice: Seleziona tutto
sudo apt-get install smartmontools
Codice: Seleziona tutto
sudo smartctl -a /dev/sdX
Codice: Seleziona tutto
sudo apt-get install smartmontools
Codice: Seleziona tutto
sudo smartctl -a /dev/sdX
Codice: Seleziona tutto
[lubuntu@lubuntu:~$ sudo smartctl -a /dev/sdf
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.8.0-22-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, http://www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Samsung based SSDs
Device Model: Samsung SSD 850 EVO 1TB
Serial Number: S2RFNXAH300755A
LU WWN Device Id: 5 002538 d40bfccc7
Firmware Version: EMT02B6Q
User Capacity: 1.000.204.886.016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ATA8-ACS T13/1699-D revision 4c
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Oct 15 15:45:26 2016 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x53) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 512) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 1
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 560
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 1056
177 Wear_Leveling_Count 0x0013 099 099 000 Pre-fail Always - 1
179 Used_Rsvd_Blk_Cnt_Tot 0x0013 100 100 010 Pre-fail Always - 0
181 Program_Fail_Cnt_Total 0x0032 100 100 010 Old_age Always - 0
182 Erase_Fail_Count_Total 0x0032 100 100 010 Old_age Always - 0
183 Runtime_Bad_Block 0x0013 100 100 010 Pre-fail Always - 0
187 Uncorrectable_Error_Cnt 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0032 072 056 000 Old_age Always - 28
195 ECC_Error_Rate 0x001a 200 200 000 Old_age Always - 0
199 CRC_Error_Count 0x003e 100 100 000 Old_age Always - 0
235 POR_Recovery_Count 0x0012 099 099 000 Old_age Always - 71
241 Total_LBAs_Written 0x0032 099 099 000 Old_age Always - 4467947910
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
255 0 65535 Read_scanning was never started
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
lubuntu@lubuntu:~$
Codice: Seleziona tutto
[img]http://forum.ubuntu-it.org/download/file.php?id=2777[/img]
Devi usare l'editor completo, non è difficile, basta marcare il testo e premere il pulsante o meglio premerlo prima di incollare, per ora l'ho fatto io.ginoza [url=http://forum.ubuntu-it.org/viewtopic.php?p=4925518#p4925518][img]http://forum.ubuntu-it.org/images/icons/icona-cita.gif[/img][/url] ha scritto:chiedo venia e pardon...ma non so come fare il tag richiesto dello scritto. Sono ancora molto neofito di certe cosa di linux.
Gino.
Visualizzano questa sezione: 0 utenti iscritti e 7 ospiti