Compilazione del kernel, gestione moduli, servizi attivi, e tutti gli interventi per l'ottimizzazione del sistema operativo.
'Leonardo'
Scoppiettante Seguace
Messaggi: 524 Iscrizione: venerdì 20 giugno 2008, 13:40
Messaggio
da 'Leonardo' mercoledì 7 settembre 2016, 16:05
sudo dmidecode -t 16
Codice: Seleziona tutto
# dmidecode 3.0
Getting SMBIOS data from sysfs.
SMBIOS 2.7 present.
Invalid entry length (16). Fixed up to 11.
Handle 0x0053, DMI type 16, 23 bytes
Physical Memory Array
Location: System Board Or Motherboard
Use: System Memory
Error Correction Type: None
Maximum Capacity: 16 GB
Error Information Handle: 0x0054
Number Of Devices: 2
sudo dmidecode -t 17
Codice: Seleziona tutto
# dmidecode 3.0
Getting SMBIOS data from sysfs.
SMBIOS 2.7 present.
Invalid entry length (16). Fixed up to 11.
Handle 0x0052, DMI type 17, 34 bytes
Memory Device
Array Handle: 0x0053
Error Information Handle: 0x0057
Total Width: 64 bits
Data Width: 64 bits
Size: 4096 MB
Form Factor: DIMM
Set: None
Locator: ChannelA-DIMM0
Bank Locator: BANK 0
Type: DDR3
Type Detail: Synchronous
Speed: 1067 MHz
Manufacturer: Kingston
Serial Number: 832AD178
Asset Tag: 9876543210
Part Number: 99U5471-012.A00LF
Rank: 2
Configured Clock Speed: 1067 MHz
Handle 0x0056, DMI type 17, 34 bytes
Memory Device
Array Handle: 0x0053
Error Information Handle: No Error
Total Width: Unknown
Data Width: Unknown
Size: No Module Installed
Form Factor: DIMM
Set: None
Locator: ChannelB-DIMM0
Bank Locator: BANK 2
Type: Unknown
Type Detail: None
Speed: Unknown
Manufacturer: [Empty]
Serial Number: [Empty]
Asset Tag: 9876543210
Part Number: [Empty]
Rank: Unknown
Configured Clock Speed: Unknown
'Leonardo'
Scoppiettante Seguace
Messaggi: 524 Iscrizione: venerdì 20 giugno 2008, 13:40
Messaggio
da 'Leonardo' mercoledì 7 settembre 2016, 16:33
Oltre ai due comandi di sopra già postati, se possono servire posto anche i seguenti:
sudo smartctl -a /dev/sda
Codice: Seleziona tutto
smartctl 6.5 2016-01-24 r4214 [i686-linux-4.4.0-36-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: MAXTOR STM3160613AS
Serial Number: 9SY380GK
LU WWN Device Id: 5 000c50 01a1f9658
Firmware Version: MC1J
User Capacity: 160.041.885.696 bytes [160 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Wed Sep 7 16:29:34 2016 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 34) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 113 099 006 Pre-fail Always - 58340394
3 Spin_Up_Time 0x0003 100 100 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1865
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 075 060 030 Pre-fail Always - 33633675
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1961
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 037 020 Old_age Always - 1865
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 099 000 Old_age Always - 556
189 High_Fly_Writes 0x003a 074 074 000 Old_age Always - 26
190 Airflow_Temperature_Cel 0x0022 065 058 045 Old_age Always - 35 (Min/Max 24/35)
194 Temperature_Celsius 0x0022 035 042 000 Old_age Always - 35 (0 14 0 0 0)
195 Hardware_ECC_Recovered 0x001a 065 052 000 Old_age Always - 58340394
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 1960 (102 174 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 3446301796
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 2644475984
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
inxi -Fz
Codice: Seleziona tutto
System: Host: leonardo-System-Product-Name Kernel: 4.4.0-36-generic i686 (32 bit)
Desktop: Unity 7.4.0 Distro: Ubuntu 16.04 xenial
Machine: Mobo: ASUSTeK model: P8H61-M LX3 PLUS R2.0 v: Rev X.0x
Bios: American Megatrends v: 0609 date: 08/14/2012
CPU: Dual core Intel Celeron G550 (-MCP-) cache: 2048 KB
clock speeds: max: 2600 MHz 1: 1609 MHz 2: 1600 MHz
Graphics: Card: Intel 2nd Generation Core Processor Family Integrated Graphics Controller
Display Server: X.Org 1.18.3 drivers: intel (unloaded: fbdev,vesa)
Resolution: 1024x768@60.00hz
GLX Renderer: Mesa DRI Intel Sandybridge Desktop x86/MMX/SSE2 GLX Version: 3.0 Mesa 11.2.0
Audio: Card Intel 6 Series/C200 Series Family High Definition Audio Controller driver: snd_hda_intel
Sound: Advanced Linux Sound Architecture v: k4.4.0-36-generic
Network: Card: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller driver: r8169
IF: eth0 state: up speed: 100 Mbps duplex: full mac: <filter>
Drives: HDD Total Size: 160.0GB (36.0% used) ID-1: /dev/sda model: MAXTOR_STM316061 size: 160.0GB
Partition: ID-1: / size: 65G used: 51G (82%) fs: ext4 dev: /dev/sda5
ID-2: swap-1 size: 3.97GB used: 0.00GB (0%) fs: swap dev: /dev/sda6
RAID: No RAID devices: /proc/mdstat, md_mod kernel module present
Sensors: System Temperatures: cpu: 29.8C mobo: 27.8C
Fan Speeds (in rpm): cpu: 0
Info: Processes: 186 Uptime: 39 min Memory: 911.3/3731.8MB Client: Shell (bash) inxi: 2.2.35
Visualizzano questa sezione: 0 utenti iscritti e 9 ospiti
