[Risolto] Problemi scheda audio!! HP dv2055ea

Riconoscimento, installazione e configurazione delle periferiche.
chiccoach
Prode Principiante
Messaggi: 136
Iscrizione: domenica 22 aprile 2007, 19:08

[Risolto] Problemi scheda audio!! HP dv2055ea

Messaggio da chiccoach »

Ciao ragazzi

il mio problema è semplice: non funziona l'audio ???....che devo fare???

ho un portatile con una scheda audio 3d soundblaster pro 16bit

grazie!!!
ciao
Ultima modifica di chiccoach il domenica 23 dicembre 2007, 8:50, modificato 1 volta in totale.
schnauzer
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 472
Iscrizione: sabato 5 maggio 2007, 12:14

Re: problemi audio!!!!

Messaggio da schnauzer »

chiccoach ha scritto: Ciao ragazzi

il mio problema è semplice: non funziona l'audio ???....che devo fare???

ho un portatile con una scheda audio 3d soundblaster pro 16bit

grazie!!!
ciao
"dottore ho la febbre: che devo fare??" Devi specificare un po di cose e mi servono più info.

riporta qui (dentro il tag # che trovi quando scrivi le risposte sopra, ti prego :) ) il risultato dei seguenti comandi da console:

Codice: Seleziona tutto

dmesg

Codice: Seleziona tutto

sudo lspci

Codice: Seleziona tutto

sudo lsmod
chiccoach
Prode Principiante
Messaggi: 136
Iscrizione: domenica 22 aprile 2007, 19:08

Re: problemi audio!!!!

Messaggio da chiccoach »

Allora:
Con

Codice: Seleziona tutto

dmesg
ottengo

Codice: Seleziona tutto

[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[    0.000000] Detected 1662.712 MHz processor.
[   10.688257] Built 1 zonelists.  Total pages: 259715
[   10.688261] Kernel command line: root=UUID=3b457f1a-62a7-4e6a-bf81-48ec81266472 ro quiet splash
[   10.688421] mapped APIC to ffffd000 (fee00000)
[   10.688423] mapped IOAPIC to ffffc000 (fec00000)
[   10.688426] Enabling fast FPU save and restore... done.
[   10.688429] Enabling unmasked SIMD FPU exception support... done.
[   10.688436] Initializing CPU#0
[   10.688508] PID hash table entries: 4096 (order: 12, 16384 bytes)
[   10.691743] Console: colour VGA+ 80x25
[   10.691994] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[   10.692352] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[   10.719641] Memory: 1026860k/1047040k available (1992k kernel code, 19508k reserved, 893k data, 328k init, 129536k highmem)
[   10.719651] virtual kernel memory layout:
[   10.719653]     fixmap  : 0xfff4e000 - 0xfffff000   ( 708 kB)
[   10.719654]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[   10.719655]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[   10.719657]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[   10.719658]       .init : 0xc03d7000 - 0xc0429000   ( 328 kB)
[   10.719659]       .data : 0xc02f2264 - 0xc03d16d4   ( 893 kB)
[   10.719661]       .text : 0xc0100000 - 0xc02f2264   (1992 kB)
[   10.719664] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[   10.796359] Calibrating delay using timer specific routine.. 3328.98 BogoMIPS (lpj=6657972)
[   10.796398] Security Framework v1.0.0 initialized
[   10.796405] SELinux:  Disabled at boot.
[   10.796420] Mount-cache hash table entries: 512
[   10.796544] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
[   10.796552] monitor/mwait feature present.
[   10.796554] using mwait in idle threads.
[   10.796558] CPU: L1 I cache: 32K, L1 D cache: 32K
[   10.796561] CPU: L2 cache: 2048K
[   10.796564] CPU: Physical Processor ID: 0
[   10.796565] CPU: Processor Core ID: 0
[   10.796568] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c189 00000000 00000000
[   10.796577] Compat vDSO mapped to ffffe000.
[   10.796580] Remapping vsyscall page to ffffe000
[   10.796592] Checking 'hlt' instruction... OK.
[   10.812430] SMP alternatives: switching to UP code
[   10.812762] Early unpacking initramfs... done
[   11.145622] ACPI: Core revision 20060707
[   11.145835] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[   11.203432] CPU0: Intel Genuine Intel(R) CPU           T2300  @ 1.66GHz stepping 08
[   11.203453] SMP alternatives: switching to SMP code
[   11.203560] Booting processor 1/1 eip 3000
[   11.213963] Initializing CPU#1
[   11.291627] Calibrating delay using timer specific routine.. 3315.69 BogoMIPS (lpj=6631382)
[   11.291634] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
[   11.291640] monitor/mwait feature present.
[   11.291643] CPU: L1 I cache: 32K, L1 D cache: 32K
[   11.291645] CPU: L2 cache: 2048K
[   11.291648] CPU: Physical Processor ID: 0
[   11.291649] CPU: Processor Core ID: 1
[   11.291651] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c189 00000000 00000000
[   11.292127] CPU1: Intel Genuine Intel(R) CPU           T2300  @ 1.66GHz stepping 08
[   11.292152] Total of 2 processors activated (6644.67 BogoMIPS).
[   11.292348] ENABLING IO-APIC IRQs
[   11.292553] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[   11.439430] checking TSC synchronization across 2 CPUs: passed.
[    0.003992] Brought up 2 CPUs
[    0.162204] migration_cost=30026
[    0.162484] Booting paravirtualized kernel on bare hardware
[    0.162586] Time: 20:38:36  Date: 04/13/107
[    0.162615] NET: Registered protocol family 16
[    0.162700] EISA bus registered
[    0.162705] ACPI: bus type pci registered
[    0.162832] PCI: PCI BIOS revision 2.10 entry at 0xfd733, last bus=8
[    0.162834] PCI: Using configuration type 1
[    0.162836] Setting up standard PCI resources
[    0.168540] ACPI: Interpreter enabled
[    0.168543] ACPI: Using IOAPIC for interrupt routing
[    0.169152] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.169158] PCI: Probing PCI hardware (bus 00)
[    0.169218] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[    0.170543] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[    0.170548] PCI quirk: region 1180-11bf claimed by ICH6 GPIO
[    0.170849] Boot video device is 0000:01:00.0
[    0.171526] PCI: Firmware left 0000:08:08.0 e100 interrupts enabled, disabling
[    0.171959] PCI: Transparent bridge - 0000:00:1e.0
[    0.172043] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.175303] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[    0.176164] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[    0.176424] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[    0.176676] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[    0.177130] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[    0.177704] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.177949] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.178192] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[    0.178430] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.178670] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.178912] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[    0.179152] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.179391] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.190241] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.190250] pnp: PnP ACPI init
[    0.193076] pnp: PnP ACPI: found 10 devices
[    0.193081] PnPBIOS: Disabled by ACPI PNP
[    0.193123] PCI: Using ACPI for IRQ routing
[    0.193126] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[    0.221859] NET: Registered protocol family 8
[    0.221861] NET: Registered protocol family 20
[    0.222046] pnp: 00:06: ioport range 0x6a0-0x6af has been reserved
[    0.222049] pnp: 00:06: ioport range 0x6b0-0x6ff has been reserved
[    0.222333] PCI: Bridge: 0000:00:01.0
[    0.222335]   IO window: disabled.
[    0.222339]   MEM window: d4000000-d5ffffff
[    0.222342]   PREFETCH window: c0000000-cfffffff
[    0.222346] PCI: Bridge: 0000:00:1c.0
[    0.222349]   IO window: 2000-2fff
[    0.222355]   MEM window: d2000000-d3ffffff
[    0.222360]   PREFETCH window: d0000000-d1ffffff
[    0.222366] PCI: Bridge: 0000:00:1c.2
[    0.222368]   IO window: disabled.
[    0.222374]   MEM window: disabled.
[    0.222378]   PREFETCH window: disabled.
[    0.222384] PCI: Bridge: 0000:00:1c.3
[    0.222385]   IO window: disabled.
[    0.222391]   MEM window: d6000000-d60fffff
[    0.222396]   PREFETCH window: disabled.
[    0.222402] PCI: Bridge: 0000:00:1e.0
[    0.222405]   IO window: 3000-3fff
[    0.222412]   MEM window: d6100000-d61fffff
[    0.222416]   PREFETCH window: disabled.
[    0.222432] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.222438] PCI: Setting latency timer of device 0000:00:01.0 to 64
[    0.222461] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[    0.222467] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    0.222490] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[    0.222497] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[    0.222520] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
[    0.222526] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[    0.222540] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[    0.222567] NET: Registered protocol family 2
[    0.259648] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.259749] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.260470] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.260840] TCP: Hash tables configured (established 131072 bind 65536)
[    0.260843] TCP reno registered
[    0.275707] checking if image is initramfs... it is
[    1.015392] Freeing initrd memory: 6793k freed
[    1.015575] Simple Boot Flag at 0x36 set to 0x1
[    1.016037] audit: initializing netlink socket (disabled)
[    1.016053] audit(1179088717.700:1): initialized
[    1.016147] highmem bounce pool size: 64 pages
[    1.016233] VFS: Disk quotas dquot_6.5.1
[    1.016252] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.016299] io scheduler noop registered
[    1.016302] io scheduler anticipatory registered
[    1.016304] io scheduler deadline registered
[    1.016316] io scheduler cfq registered (default)
[    1.016565] PCI: Setting latency timer of device 0000:00:01.0 to 64
[    1.016600] assign_interrupt_mode Found MSI capability
[    1.016603] Allocate Port Service[0000:00:01.0:pcie00]
[    1.016694] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    1.016750] assign_interrupt_mode Found MSI capability
[    1.016753] Allocate Port Service[0000:00:1c.0:pcie00]
[    1.016789] Allocate Port Service[0000:00:1c.0:pcie02]
[    1.016912] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[    1.016968] assign_interrupt_mode Found MSI capability
[    1.016970] Allocate Port Service[0000:00:1c.2:pcie00]
[    1.017004] Allocate Port Service[0000:00:1c.2:pcie02]
[    1.017123] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[    1.017179] assign_interrupt_mode Found MSI capability
[    1.017182] Allocate Port Service[0000:00:1c.3:pcie00]
[    1.017214] Allocate Port Service[0000:00:1c.3:pcie02]
[    1.017396] isapnp: Scanning for PnP cards...
[    1.370461] isapnp: No Plug & Play device found
[    1.394243] Real Time Clock Driver v1.12ac
[    1.394301] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[    1.394949] mice: PS/2 mouse device common for all mice
[    1.395517] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[    1.395669] input: Macintosh mouse button emulation as /class/input/input0
[    1.395706] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[    1.395710] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[    1.395999] PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    1.396219] i8042.c: Detected active multiplexing controller, rev 1.1.
[    1.396295] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.396299] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    1.396302] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    1.396305] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    1.396308] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    1.396408] EISA: Probing bus 0 at eisa.0
[    1.396415] Cannot allocate resource for EISA slot 1
[    1.396419] Cannot allocate resource for EISA slot 2
[    1.396422] Cannot allocate resource for EISA slot 3
[    1.396445] EISA: Detected 0 cards.
[    1.426500] TCP cubic registered
[    1.426511] NET: Registered protocol family 1
[    1.426534] Starting balanced_irq
[    1.426541] Using IPI No-Shortcut mode
[    1.426627] input: AT Translated Set 2 keyboard as /class/input/input1
[    1.426685] ACPI: (supports S0 S3 S4 S5)
[    1.426753]   Magic number: 7:672:649
[    1.426803]   hash matches device ptyde
[    1.427058] Freeing unused kernel memory: 328k freed
[    1.429873] Time: tsc clocksource has been installed.
[    2.658066] Capability LSM initialized
[    2.694020] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Ist] [20060707]
[    2.694229] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Cst] [20060707]
[    2.694434] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[    2.694439] ACPI: Processor [CPU0] (supports 8 throttling states)
[    2.694941] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Ist] [20060707]
[    2.695135] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Cst] [20060707]
[    2.695397] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[    2.695403] ACPI: Processor [CPU1] (supports 8 throttling states)
[    3.208000] Time: acpi_pm clocksource has been installed.
[    3.208000] ACPI: Thermal Zone [TZS0] (36 C)
[    3.212000] ACPI: Thermal Zone [TZS1] (36 C)
[    3.612000] usbcore: registered new interface driver usbfs
[    3.612000] usbcore: registered new interface driver hub
[    3.612000] usbcore: registered new device driver usb
[    3.612000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
[    3.612000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[    3.612000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    3.612000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    3.612000] ehci_hcd 0000:00:1d.7: debug port 1
[    3.612000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[    3.612000] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xd6404000
[    3.616000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    3.616000] usb usb1: configuration #1 chosen from 1 choice
[    3.616000] hub 1-0:1.0: USB hub found
[    3.616000] hub 1-0:1.0: 8 ports detected
[    3.620000] SCSI subsystem initialized
[    3.648000] libata version 2.20 loaded.
[    3.660000] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI
[    3.660000] e100: Copyright(c) 1999-2006 Intel Corporation
[    3.672000] ieee1394: Initialized config rom entry `ip1394'
[    3.688000] USB Universal Host Controller Interface driver v3.0
[    3.736000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
[    3.736000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[    3.736000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    3.736000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    3.736000] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001800
[    3.736000] usb usb2: configuration #1 chosen from 1 choice
[    3.736000] hub 2-0:1.0: USB hub found
[    3.736000] hub 2-0:1.0: 2 ports detected
[    3.840000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[    3.840000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[    3.840000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    3.840000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    3.840000] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
[    3.840000] usb usb3: configuration #1 chosen from 1 choice
[    3.840000] hub 3-0:1.0: USB hub found
[    3.840000] hub 3-0:1.0: 2 ports detected
[    3.944000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 21 (level, low) -> IRQ 21
[    3.944000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[    3.944000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    3.944000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    3.944000] uhci_hcd 0000:00:1d.2: irq 21, io base 0x00001840
[    3.944000] usb usb4: configuration #1 chosen from 1 choice
[    3.944000] hub 4-0:1.0: USB hub found
[    3.944000] hub 4-0:1.0: 2 ports detected
[    3.960000] usb 1-5: new high speed USB device using ehci_hcd and address 2
[    4.048000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[    4.048000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[    4.048000] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    4.048000] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    4.048000] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
[    4.048000] usb usb5: configuration #1 chosen from 1 choice
[    4.048000] hub 5-0:1.0: USB hub found
[    4.048000] hub 5-0:1.0: 2 ports detected
[    4.100000] usb 1-5: configuration #1 chosen from 1 choice
[    4.152000] ACPI: PCI Interrupt 0000:08:08.0[A] -> GSI 20 (level, low) -> IRQ 22
[    4.192000] e100: eth0: e100_probe: addr 0xd6100000, irq 22, MAC addr 00:16:D3:09:20:24
[    4.192000] ahci 0000:00:1f.2: version 2.1
[    4.192000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[    4.668000] usb 4-2: new full speed USB device using uhci_hcd and address 2
[    4.840000] usb 4-2: configuration #1 chosen from 1 choice
[    5.196000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[    5.196000] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode
[    5.196000] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part 
[    5.196000] ata1: SATA max UDMA/133 cmd 0xf885a500 ctl 0x00000000 bmdma 0x00000000 irq 19
[    5.196000] ata2: SATA max UDMA/133 cmd 0xf885a580 ctl 0x00000000 bmdma 0x00000000 irq 19
[    5.196000] ata3: SATA max UDMA/133 cmd 0xf885a600 ctl 0x00000000 bmdma 0x00000000 irq 19
[    5.196000] ata4: SATA max UDMA/133 cmd 0xf885a680 ctl 0x00000000 bmdma 0x00000000 irq 19
[    5.196000] scsi0 : ahci
[    5.680000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    5.680000] ata1.00: ATA-7: WDC WD1200BEVS-60LAT0, 01.06M01, max UDMA/100
[    5.680000] ata1.00: 234441648 sectors, multi 16: LBA48 
[    5.680000] ata1.00: configured for UDMA/100
[    5.680000] scsi1 : ahci
[    5.992000] ata2: SATA link down (SStatus 0 SControl 0)
[    5.992000] scsi2 : ahci
[    6.304000] ata3: SATA link down (SStatus 0 SControl 300)
[    6.304000] scsi3 : ahci
[    6.616000] ata4: SATA link down (SStatus 0 SControl 0)
[    6.616000] scsi 0:0:0:0: Direct-Access     ATA      WDC WD1200BEVS-6 01.0 PQ: 0 ANSI: 5
[    6.616000] ata_piix 0000:00:1f.1: version 2.10ac1
[    6.616000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[    6.616000] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[    6.616000] ata5: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00011880 irq 14
[    6.616000] ata6: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x00011888 irq 15
[    6.616000] scsi4 : ata_piix
[    6.620000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[    6.620000] sda: Write Protect is off
[    6.620000] sda: Mode Sense: 00 3a 00 00
[    6.620000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.620000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[    6.620000] sda: Write Protect is off
[    6.620000] sda: Mode Sense: 00 3a 00 00
[    6.620000] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.620000]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[    6.720000] sd 0:0:0:0: Attached scsi disk sda
[    6.724000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    6.936000] ata5.00: ATAPI, max MWDMA2
[    7.100000] ata5.00: configured for MWDMA2
[    7.100000] scsi5 : ata_piix
[    7.100000] ata6: port disabled. ignoring.
[    7.104000] scsi 4:0:0:0: CD-ROM            HL-DT-ST DVDRAM GMA-4082N HQ04 PQ: 0 ANSI: 5
[    7.104000] scsi 4:0:0:0: Attached scsi generic sg1 type 5
[    7.104000] ACPI: PCI Interrupt 0000:08:09.0[A] -> GSI 16 (level, low) -> IRQ 16
[    7.156000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]  MMIO=[d6101000-d61017ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
[    7.160000] Attempting manual resume
[    7.160000] swsusp: Resume From Partition 8:6
[    7.160000] PM: Checking swsusp image.
[    7.160000] PM: Resume from disk failed.
[    7.192000] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    7.192000] Uniform CD-ROM driver Revision: 3.20
[    7.192000] sr 4:0:0:0: Attached scsi CD-ROM sr0
[    7.196000] kjournald starting.  Commit interval 5 seconds
[    7.196000] EXT3-fs: mounted filesystem with ordered data mode.
[    8.432000] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[06e40a005aae5031]
[   18.620000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   18.624000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   18.860000] iTCO_vendor_support: vendor-support=0
[   18.860000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
[   18.860000] iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060)
[   18.860000] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   18.896000] intel_rng: FWH not detected
[   18.908000] Linux agpgart interface v0.102 (c) Dave Jones
[   18.908000] agpgart: Detected an Intel 945GM Chipset.
[   18.928000] agpgart: AGP aperture is 256M @ 0x0
[   19.344000] Bluetooth: Core ver 2.11
[   19.344000] NET: Registered protocol family 31
[   19.344000] Bluetooth: HCI device and connection manager initialized
[   19.344000] Bluetooth: HCI socket layer initialized
[   19.356000] Bluetooth: HCI USB driver ver 2.9
[   19.432000] NET: Registered protocol family 17
[   19.448000] usbcore: registered new interface driver hci_usb
[   19.532000] ieee80211_crypt: registered algorithm 'NULL'
[   19.544000] ieee80211: 802.11 data/management/control stack, git-1.1.13
[   19.544000] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[   19.620000] Linux video capture interface: v2.00
[   19.640000] sdhci: Secure Digital Host Controller Interface driver
[   19.640000] sdhci: Copyright(c) Pierre Ossman
[   19.640000] sdhci: SDHCI controller found at 0000:08:09.1 [1180:0822] (rev 19)
[   19.640000] ACPI: PCI Interrupt 0000:08:09.1[B] -> GSI 18 (level, low) -> IRQ 18
[   19.640000] mmc0: SDHCI at 0xd6101800 irq 18 DMA
[   19.668000] ipw3945: Intel(R) PRO/Wireless 3945 Network Connection driver for Linux, 1.2.0mp
[   19.668000] ipw3945: Copyright(c) 2003-2006 Intel Corporation
[   19.668000] ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 19 (level, low) -> IRQ 19
[   19.668000] PCI: Setting latency timer of device 0000:05:00.0 to 64
[   19.668000] ipw3945: Detected Intel PRO/Wireless 3945ABG Network Connection
[   19.844000] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (0c45:62c0)
[   19.844000] usbcore: registered new interface driver uvcvideo
[   19.844000] USB Video Class driver (v0.1.0)
[   19.848000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04713/0x200000
[   19.880000] input: SynPS/2 Synaptics TouchPad as /class/input/input2
[   19.944000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 23
[   19.944000] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   20.456000] fuse init (API version 7.8)
[   20.568000] lp: driver loaded but no devices found
[   20.612000] Adding 3349512k swap on /dev/disk/by-uuid/539eeb6f-5684-4920-98bb-c16f424af522.  Priority:-1 extents:1 across:3349512k
[   20.828000] EXT3 FS on sda5, internal journal
[   21.572000] ipw3945: Detected geography ABG (13 802.11bg channels, 23 802.11a channels)
[   22.712000] NTFS driver 2.1.28 [Flags: R/O MODULE].
[   22.832000] NTFS volume version 3.1.
[   23.088000] NTFS volume version 3.1.
[   27.392000] Using specific hotkey driver
[   27.428000] No dock devices found.
[   27.520000] ibm_acpi: ec object not found
[   27.600000] ACPI: Battery Slot [BAT0] (battery present)
[   27.636000] ACPI: AC Adapter [ADP1] (on-line)
[   27.668000] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   27.668000] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   27.680000] input: Power Button (FF) as /class/input/input3
[   27.680000] ACPI: Power Button (FF) [PWRF]
[   27.680000] input: Lid Switch as /class/input/input4
[   27.680000] ACPI: Lid Switch [LID0]
[   27.680000] input: Sleep Button (CM) as /class/input/input5
[   27.680000] ACPI: Sleep Button (CM) [SLPB]
[   27.680000] input: Power Button (CM) as /class/input/input6
[   27.680000] ACPI: Power Button (CM) [PWRB]
[   27.828000] pcc_acpi: loading...
[   27.836000] wmi_add device=df8c7c00
[   27.836000] calling WQBA
[   34.664000] ppdev: user-space parallel port driver
[   35.364000] apm: BIOS not found.
[   35.512000] APIC error on CPU0: 00(40)
[   35.512000] APIC error on CPU1: 00(40)
[   35.540000] Bluetooth: L2CAP ver 2.8
[   35.540000] Bluetooth: L2CAP socket layer initialized
[   35.652000] Bluetooth: RFCOMM socket layer initialized
[   35.652000] Bluetooth: RFCOMM TTY layer initialized
[   35.652000] Bluetooth: RFCOMM ver 1.8
[   50.540000] NET: Registered protocol family 10
[   50.540000] lo: Disabled Privacy Extensions
[   50.540000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   50.540000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[   59.852000] ipw3945: association process canceled
[   59.852000] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   74.612000] ADDRCONF(NETDEV_UP): eth1: link is not ready
[   80.728000] ieee80211_crypt: registered algorithm 'WEP'
[   80.848000] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   96.960000] eth1: no IPv6 routers present
[ 1383.636000] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 1383.812000] usb 3-1: configuration #1 chosen from 1 choice
[ 1383.936000] usbcore: registered new interface driver hiddev
[ 1383.948000] input: Wireless Mouse Wireless Mouse as /class/input/input7
[ 1383.948000] input: USB HID v1.10 Mouse [Wireless Mouse Wireless Mouse] on usb-0000:00:1d.1-1
[ 1383.948000] usbcore: registered new interface driver usbhid
[ 1383.948000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 3376.412000] usb 3-1: USB disconnect, address 2
mentre con

Codice: Seleziona tutto

sudo lspci
ottengo

Codice: Seleziona tutto

00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express PCI Express Root Port (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02)
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 02)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controller AHCI (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
01:00.0 VGA compatible controller: nVidia Corporation GeForce Go 7200 (rev a1)
05:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02)
08:08.0 Ethernet controller: Intel Corporation PRO/100 VE Network Connection (rev 02)
08:09.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
08:09.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
08:09.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
08:09.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a)
08:09.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
Con

Codice: Seleziona tutto

sudo lsmod
ottengo

Codice: Seleziona tutto

00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express Memory Controller Hub (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS/940GML and 945GT Express PCI Express Root Port (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02)
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 02)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) Serial ATA Storage Controller AHCI (rev 02)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02)
01:00.0 VGA compatible controller: nVidia Corporation GeForce Go 7200 (rev a1)
05:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02)
08:08.0 Ethernet controller: Intel Corporation PRO/100 VE Network Connection (rev 02)
08:09.0 FireWire (IEEE 1394): Ricoh Co Ltd Unknown device 0832
08:09.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19)
08:09.2 System peripheral: Ricoh Co Ltd Unknown device 0843 (rev 01)
08:09.3 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a)
08:09.4 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05)
federico@federico-laptop:~$ sudo lsmod
Module                  Size  Used by
usbhid                 26592  0 
hid                    27392  1 usbhid
arc4                    2944  2 
ecb                     4480  2 
blkcipher               6784  1 ecb
ieee80211_crypt_wep     6144  1 
ipv6                  268704  10 
binfmt_misc            12680  1 
rfcomm                 40856  0 
l2cap                  25728  5 rfcomm
ppdev                  10116  0 
acpi_cpufreq           10056  0 
cpufreq_stats           7360  0 
cpufreq_powersave       2688  0 
cpufreq_ondemand        9228  2 
freq_table              5792  3 acpi_cpufreq,cpufreq_stats,cpufreq_ondemand
cpufreq_userspace       5408  0 
cpufreq_conservative     8200  0 
tc1100_wmi              8068  0 
pcc_acpi               13184  0 
dev_acpi               12292  0 
sony_acpi               6284  0 
button                  8720  0 
video                  16388  0 
ac                      6020  0 
container               5248  0 
battery                10756  0 
sbs                    15652  0 
i2c_ec                  5888  1 sbs
asus_acpi              17308  0 
backlight               7040  1 asus_acpi
dock                   10268  0 
nls_iso8859_1           5120  1 
nls_cp437               6784  1 
vfat                   14208  1 
fat                    53916  1 vfat
nls_utf8                3072  2 
ntfs                  107764  2 
sbp2                   23812  0 
parport_pc             36388  0 
lp                     12452  0 
parport                36936  3 ppdev,parport_pc,lp
fuse                   46612  0 
joydev                 10816  0 
snd_hda_intel          21912  3 
snd_hda_codec         205440  1 snd_hda_intel
snd_pcm_oss            44544  0 
snd_mixer_oss          17408  1 snd_pcm_oss
snd_pcm                79876  4 snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd_seq_dummy           4740  0 
snd_seq_oss            32896  0 
snd_seq_midi            9600  0 
snd_rawmidi            25472  1 snd_seq_midi
snd_seq_midi_event      8448  2 snd_seq_oss,snd_seq_midi
uvcvideo               42500  0 
snd_seq                52592  6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
ipw3945               118816  1 
sdhci                  18700  0 
videodev               28160  1 uvcvideo
v4l1_compat            15236  2 uvcvideo,videodev
snd_timer              23684  3 snd_pcm,snd_seq
snd_seq_device          9100  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
ieee80211              34760  1 ipw3945
ieee80211_crypt         7040  2 ieee80211_crypt_wep,ieee80211
v4l2_common            25216  2 uvcvideo,videodev
mmc_core               26756  1 sdhci
af_packet              23816  10 
i2c_core               22784  1 i2c_ec
hci_usb                18204  2 
bluetooth              55908  7 rfcomm,l2cap,hci_usb
serio_raw               7940  0 
psmouse                38920  0 
snd                    54020  14 snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore               8672  1 snd
snd_page_alloc         10888  2 snd_hda_intel,snd_pcm
intel_agp              25116  1 
agpgart                35400  1 intel_agp
iTCO_wdt               11812  0 
iTCO_vendor_support     4868  1 iTCO_wdt
shpchp                 34324  0 
pci_hotplug            32576  1 shpchp
evdev                  11008  5 
tsdev                   8768  0 
ext3                  133128  1 
jbd                    59816  1 ext3
sr_mod                 17060  0 
cdrom                  37664  1 sr_mod
mbcache                 9604  1 ext3
generic                 5124  0 [permanent]
sg                     36252  0 
sd_mod                 23428  6 
ata_piix               15492  0 
ahci                   22020  5 
uhci_hcd               25360  0 
ohci1394               36528  0 
ieee1394              299448  2 sbp2,ohci1394
e100                   36232  0 
mii                     6528  1 e100
ata_generic             9092  0 
libata                125720  3 ata_piix,ahci,ata_generic
scsi_mod              142348  5 sbp2,sr_mod,sg,sd_mod,libata
ehci_hcd               34188  0 
usbcore               134280  6 usbhid,uvcvideo,hci_usb,uhci_hcd,ehci_hcd
thermal                14856  0 
processor              31048  2 acpi_cpufreq,thermal
fan                     5636  0 
fbcon                  42656  0 
tileblit                3584  1 fbcon
font                    9216  1 fbcon
bitblit                 6912  1 fbcon
softcursor              3200  1 bitblit
vesafb                  9220  0 
capability              5896  0 
commoncap               8192  1 capability

di cosa sono malato? :)
schnauzer
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 472
Iscrizione: sabato 5 maggio 2007, 12:14

Re: problemi audio!!!!

Messaggio da schnauzer »

Codice: Seleziona tutto

sudo dpkg-reconfigure alsa-base
fai anche un

Codice: Seleziona tutto

sudo alsaconf
chiccoach
Prode Principiante
Messaggi: 136
Iscrizione: domenica 22 aprile 2007, 19:08

Re: problemi audio!!!!

Messaggio da chiccoach »

schnauzer ha scritto:

Codice: Seleziona tutto

sudo dpkg-reconfigure alsa-base
fai anche un

Codice: Seleziona tutto

sudo alsaconf

non funziona...

il secondo codice mi dice

Codice: Seleziona tutto

sudo: alsaconf: command not found
chiccoach
Prode Principiante
Messaggi: 136
Iscrizione: domenica 22 aprile 2007, 19:08

Re: problemi audio!!!!

Messaggio da chiccoach »

chiccoach ha scritto:
schnauzer ha scritto:

Codice: Seleziona tutto

sudo dpkg-reconfigure alsa-base
fai anche un

Codice: Seleziona tutto

sudo alsaconf

non funziona...

il secondo codice mi dice

Codice: Seleziona tutto

sudo: alsaconf: command not found
HELP ME
schnauzer
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 472
Iscrizione: sabato 5 maggio 2007, 12:14

Re: problemi audio!!!!

Messaggio da schnauzer »

installa alsa-oss
chiccoach
Prode Principiante
Messaggi: 136
Iscrizione: domenica 22 aprile 2007, 19:08

Re: problemi audio!!!!

Messaggio da chiccoach »

schnauzer ha scritto: installa alsa-oss
l'ho installato ma

Codice: Seleziona tutto

sudo alsaconf
mi dice sempre command not found!!!
forest
Prode Principiante
Messaggi: 129
Iscrizione: sabato 26 novembre 2005, 17:12
Località: UTA

Re: problemi audio!!!!

Messaggio da forest »

Scrivi risposta

Ritorna a “Driver e periferiche”

Chi c’è in linea

Visualizzano questa sezione: Vinileite1 e 21 ospiti