scanner artec e+ pro

Riconoscimento, installazione e configurazione delle periferiche.
Scrivi risposta
forest
Prode Principiante
Messaggi: 129
Iscrizione: sabato 26 novembre 2005, 17:12
Località: UTA

scanner artec e+ pro

Messaggio da forest »

salve a tutti,
ubuntu 5.10 non mi fa usare lo scanner. Sembra tutto a posto, lo scanner viene riconusciuto e però quando apro xane e scelgo lo scanner mi appare la finestra che dice che lsbusb:001:002 non è un argomento valido.
ripeto lo scanner è ARTEC e+ pro...
grazie anticipate
Ultima modifica di forest il lunedì 20 novembre 2006, 7:37, modificato 1 volta in totale.
Avatar utente
pierba
Tenace Tecnocrate
Tenace Tecnocrate
Messaggi: 14532
Iscrizione: sabato 26 febbraio 2005, 19:10

Re: scanner artc e+ pro

Messaggio da pierba »

Prova lanciando xsane come root, da terminale:
sudo xsane
La prima volta facendo così, ho risolto.

ciao
Pietro pagina personale - Avete domande sul forum? Leggendo le FAQ: potreste trovare la risposta.
La conoscenza deve essere collettiva, quindi, come da regolamento (Sez. II punto 15) i messaggi personali contententi richieste di assistenza tecnica verranno ignorati.
forest
Prode Principiante
Messaggi: 129
Iscrizione: sabato 26 novembre 2005, 17:12
Località: UTA

Re: scanner artc e+ pro

Messaggio da forest »

niente!! mi risponde "command no found".

ho provato a dare scan image -L e di seguito di posto il risultato:

"device ARTEC_Eplus48u:libusb:001:002 is a Artec E+ Pro USB flatbed scanner"

???
forest
Prode Principiante
Messaggi: 129
Iscrizione: sabato 26 novembre 2005, 17:12
Località: UTA

RISOLTO!!! scanner artec e+ pro

Messaggio da forest »

ho configurato anche lo scanner  artec e+ pro se a qualcuno serve ho fatto così:
identificato lo scanner con
scanimage -L
scaricato nella cartella home il file 1200.usb dalla cartella dei driver windows
modificato con gedit il file /etc/sane.d/artec_eplus48u.conf
sono andato nella sezione che inizia con i dati rilevati cioè
usb 0x05d8 0x4004
ho corretto la riga
option artec  firmwarefile /1200.usb
con
option artec firmwarefile /home/corrado/1200.usb
quindi ho decommentato le seguenti righe
for adjusting the default gamma values
e le tre righe che iniziano con
use this options to set default offset
ho salvato e con xane ho iniziato a divertirmi
spero di essere stato chiaro ciao
Ultima modifica di forest il venerdì 11 maggio 2007, 19:48, modificato 1 volta in totale.
abec
Prode Principiante
Messaggi: 27
Iscrizione: giovedì 24 febbraio 2005, 22:25

Re: scanner artc e+ pro

Messaggio da abec »

ho il tuo identico problema e sto cercando di risolverlo seguendo le tue istruzioni, ma non avendo cd di winzoz non so dove prendere il file 1200.usb. Ho cercato un po in giro ma niente. Consigli a rigurado?
forest
Prode Principiante
Messaggi: 129
Iscrizione: sabato 26 novembre 2005, 17:12
Località: UTA

Re: scanner artc e+ pro

Messaggio da forest »

mi dispiace ma non so che dirti (al limite se mi lasci il tuo indirizzo e se non è molto pesante potrei spedirtelo..... sai purtroppo non ho l'adsl)
mi sembra di ricordare che nel sito SANE a proposito della configurazione di queso tipo di scanner si parlava di un file da recuperare nella cartella system di windows.
comunque come rientro a casa guardo quanto "pesa" il file
ciao
ultimora!!!!!!! google mi dice che si puo scaricare il driver da qui
http://www.mustek.com.tw/Download/driv_ ... 00usb.html
Ultima modifica di forest il giovedì 5 ottobre 2006, 20:46, modificato 1 volta in totale.
ubuntujtr
Prode Principiante
Messaggi: 26
Iscrizione: venerdì 9 giugno 2006, 17:47

Re: scanner artec e+ pro

Messaggio da ubuntujtr »

Ciao non so se tu sia ancora su questo forum, cmq se così fosse potresti postarmi il tuo file di configurazione per intero??
Grazie cmq ciao
forest
Prode Principiante
Messaggi: 129
Iscrizione: sabato 26 novembre 2005, 17:12
Località: UTA

Re: scanner artec e+ pro

Messaggio da forest »

ci sono, ci sono 8) anche se il tempo per me è tiranno (scusa se rispondo in ritardo..)
provo a fare copia e incolla con il testo del file di configurazione (non so in che altro modo fare)
ciao

# artec_eplus48u - SANE Backend configuration file
# For use with the Artec E+ 48U scanner
# This scanner is also sold as
# Tevion MD 9693, Medion MD 9705, Medion MD 9693,
# Trust Easy Webscan 19200, Memorex Mem 48U or Umax AstraSlim SE.
#
# The USB section:
# each device needs at least the following line:
# usb vendor-ID and product-ID
# Every device configuration in this file must begin with an usb entry.
usb 0x05d8 0x4003

#
# Path to the firmware file
# This file comes with the Windows driver
# The scanner won't work without it
#

option artecFirmwareFile /usr/share/sane/artec_eplus48u/Artec48.usb
option ePlusPro  0

#
# for adjusting the default gamma values
#

option redGamma        1.0
option greenGamma      1.0
option blueGamma        1.0
option masterGamma      1.9

#Use this options to set the default offset and exposure time values.

option redOffset        0x28
option greenOffset      0x2f
option blueOffset      0x2f
option redExposure      0xa7
option greenExposure    0x116
option blueExposure    0xdc

# The vendor and model string
# This string is displayed by the frontends. If you do not want to get your
# scanner reported as "Artec E+ 48U", then change the option accordingly.

option vendorString "Artec"
option modelString "E+ 48U"

#
# device-name
#
# If autodetection does not work, then you can specify the device here
# The device entry must be the last one in this config file (or the last one before a
# new usb entry).

#If you are using libusb, a device looks like this:
#device libusb:001:002

#If you are using the scanner module (kernel driver), a device looks like this:
#device /dev/usbscanner


# Another USB section:
# each device needs at least the following line:
# usb vendor-ID and product-ID
# Every device configuration in this file must begin with an usb entry.
# Since the Trust Easy Webscan 19200 uses a different product id, we add
# another usb section here.

usb 0x05d8 0x4006

#
# Path to the firmware file
# This file comes with the Windows driver
# The scanner won't work without it
#

option artecFirmwareFile /usr/share/sane/artec_eplus48u/Artec48.usb

#
# for adjusting the default gamma values
#
option ePlusPro        1
option redGamma        1.0
option greenGamma      1.0
option blueGamma        1.0
option masterGamma      1.9

#Use this options to set the default offset and exposure time values.
#If calibrate device is set to 0, this values are used instead of the values
#which were calculated during calibration.

option redOffset        0x28
option greenOffset      0x2f
option blueOffset      0x2f
option redExposure      0xa7
option greenExposure    0x116
option blueExposure    0xdc

# The vendor and model string
# This string is displayed by the frontends. The Trust Easy Webscan 19200
# has a different product id, therefore we can overwrite the vendor and model
# string here.

option vendorString "Trust"
option modelString "Easy Webscan 19200"

#
# device-name
#
# If autodetection does not work, then you can specify the device here
# The device entry must be the last one in this config file (or the last one before a
# new usb entry).

#If you are using libusb, a device looks like this:
#device libusb:001:002

#If you are using the scanner module (kernel driver), a device looks like this:
#device /dev/usbscanner

# Another USB section:
# each device needs at least the following line:
# usb vendor-ID and product-ID
# Every device configuration in this file must begin with an usb entry.
# Since the Memorex Mem48U uses a different product id, we add
# another usb section here.

usb 0x05d8 0x4005

#
# Path to the firmware file
# This file comes with the Windows driver
# The scanner won't work without it
#

option artecFirmwareFile /usr/share/sane/artec_eplus48u/Artec48.usb

#
# for adjusting the default gamma values
#

option redGamma        1.0
option greenGamma      1.0
option blueGamma        1.0
option masterGamma      1.9

#Use this options to set the default offset and exposure time values.
#If calibrate device is set to 0, this values are used instead of the values
#which were calculated during calibration.

option redOffset        0x28
option greenOffset      0x2f
option blueOffset      0x2f
option redExposure      0xa7
option greenExposure    0x116
option blueExposure    0xdc

# The vendor and model string
# This string is displayed by the frontends. The Umax AstraSlim SE
# has a different product id, therefore we can overwrite the vendor and model
# string here.

option vendorString "Memorex"
option modelString "MEM 48U"

#
# device-name
#
# If autodetection does not work, then you can specify the device here
# The device entry must be the last one in this config file (or the last one before a
# new usb entry).

#If you are using libusb, a device looks like this:
#device libusb:001:002

#If you are using the scanner module (kernel driver), a device looks like this:
#device /dev/usbscanner

# Another USB section:
# each device needs at least the following line:
# usb vendor-ID and product-ID
# Every device configuration in this file must begin with an usb entry.
# Since the Trust 240H Easy Webscan Gold uses a different product id, we add
# another usb section here.

usb 0x05d8 0x4007

#
# Path to the firmware file
# This file comes with the Windows driver
# The scanner won't work without it
#

option artecFirmwareFile /usr/share/sane/artec_eplus48u/Artec48.usb

#
# for adjusting the default gamma values
#
option ePlusPro        1
option redGamma        1.0
option greenGamma      1.0
option blueGamma        1.0
option masterGamma      1.9

#Use this options to set the default offset and exposure time values.
#If calibrate device is set to 0, this values are used instead of the values
#which were calculated during calibration.

option redOffset        0x28
option greenOffset      0x2f
option blueOffset      0x2f
option redExposure      0xa7
option greenExposure    0x116
option blueExposure    0xdc

# The vendor and model string
# This string is displayed by the frontends. The Trust 240H Easy Webscan Gold
# has a different product id, therefore we can overwrite the vendor and model
# string here.

option vendorString "Trust"
option modelString "240H Easy Webscan Gold"

#
# device-name
#
# If autodetection does not work, then you can specify the device here
# The device entry must be the last one in this config file (or the last one before a
# new usb entry).

#If you are using libusb, a device looks like this:
#device libusb:001:002

#If you are using the scanner module (kernel driver), a device looks like this:
#device /dev/usbscanner

# Another USB section:
# each device needs at least the following line:
# usb vendor-ID and product-ID
# Every device configuration in this file must begin with an usb entry.
# Since the Umax AstraSlim SE uses a different product id, we add
# another usb section here.

usb 0x05d8 0x4009

#
# Path to the firmware file
# This file comes with the Windows driver
# The scanner won't work without it
#

#option artecFirmwareFile /usr/share/sane/artec_eplus48u/Artec48.usb

#
# for adjusting the default gamma values
#

option redGamma        1.0
option greenGamma      1.0
option blueGamma        1.0
option masterGamma      1.9

#Use this options to set the default offset and exposure time values.
#If calibrate device is set to 0, this values are used instead of the values
#which were calculated during calibration.

option redOffset        0x28
option greenOffset      0x2f
option blueOffset      0x2f
option redExposure      0xa7
option greenExposure    0x116
option blueExposure    0xdc

# The vendor and model string
# This string is displayed by the frontends. The Umax AstraSlim SE
# has a different product id, therefore we can overwrite the vendor and model
# string here.

option vendorString "Umax"
option modelString "AstraSlim SE"

#
# device-name
#
# If autodetection does not work, then you can specify the device here
# The device entry must be the last one in this config file (or the last one before a
# new usb entry).

#If you are using libusb, a device looks like this:
#device libusb:001:002

#If you are using the scanner module (kernel driver), a device looks like this:
#device /dev/usbscanner

# Another USB section:
# each device needs at least the following line:
# usb vendor-ID and product-ID
# Every device configuration in this file must begin with an usb entry.
# This section is for the Artec E+ Pro
# Note, that the name of the firmware file is called 1200.usb for
# this device

usb 0x05d8 0x4004

#
# Path to the firmware file
# This file comes with the Windows driver
# The scanner won't work without it
#

option artecFirmwareFile /home/corrado/1200.usb

#
# Tell the backend that this is an Artec E+ Pro
# by setting the option ePlusPro to 1
#

option ePlusPro  1

#
for adjusting the default gamma values
#

option redGamma        1.0
option greenGamma      1.0
option blueGamma        1.0
option masterGamma      1.9

Use this options to set the default offset and exposure time values.
If calibrate device is set to 0, this values are used instead of the values
which were calculated during calibration.

option redOffset        0x28
option greenOffset      0x2f
option blueOffset      0x2f
option redExposure      0xa7
option greenExposure    0x116
option blueExposure    0xdc

# The vendor and model string
# This string is displayed by the frontends. The Umax AstraSlim SE
# has a different product id, therefore we can overwrite the vendor and model
# string here.

option vendorString "Artec"
option modelString "E+ Pro"

#
# device-name
#
# If autodetection does not work, then you can specify the device here
# The device entry must be the last one in this config file (or the last one before a
# new usb entry).

#If you are using libusb, a device looks like this:
#device libusb:001:002

#If you are using the scanner module (kernel driver), a device looks like this:
#device /dev/usbscanner

# Another USB section:
# each device needs at least the following line:
# usb vendor-ID and product-ID
# Every device configuration in this file must begin with an usb entry.
# This section is for the UMAX AstraSlim 1200 SE
# Note, that the name of the firmware file is called 1200.usb for
# this device

usb 0x05d8 0x4010

#
# Path to the firmware file
# This file comes with the Windows driver
# The scanner won't work without it
#

option artecFirmwareFile /usr/share/sane/artec_eplus48u/1200.usb

#
# for adjusting the default gamma values
#

option redGamma        1.0
option greenGamma      1.0
option blueGamma        1.0
option masterGamma      1.9

#Use this options to set the default offset and exposure time values.
#If calibrate device is set to 0, this values are used instead of the values
#which were calculated during calibration.

option redOffset        0x28
option greenOffset      0x2f
option blueOffset      0x2f
option redExposure      0xa7
option greenExposure    0x116
option blueExposure    0xdc

# The vendor and model string
# This string is displayed by the frontends. The Umax AstraSlim 1200 SE
# has a different product id, therefore we can overwrite the vendor and model
# string here.

option vendorString "UMAX"
option modelString "AstraSlim 1200 SE"

#
# device-name
#
# If autodetection does not work, then you can specify the device here
# The device entry must be the last one in this config file (or the last one before a
# new usb entry).

#If you are using libusb, a device looks like this:
#device libusb:001:002

#If you are using the scanner module (kernel driver), a device looks like this:
#device /dev/usbscanner
Avatar utente
giorgio.01
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 690
Iscrizione: domenica 23 dicembre 2007, 5:43

Re: scanner artec e+ pro

Messaggio da giorgio.01 »

graz5e a tutti e in particolare a forestsono riuscito ad iNSTALLARE il mio scanner arte e+pro  (b2b)

ma ora ho un alt problema con lo scanner: se masterizzo immagine in bianco e in nero tutto bene mentre se scannerizzo l'immagine  con gradazioni di grigio o a colori a prescindere della risoluzione l'immagine scannerizzata non appare uniforme ma o va a nescorendosi verso destra o se in modalita' colore va a "sputare" piu' "il blu" vorrei capire se il problema sta nel fail configurazione dello scanner (magari ho sbagliato qualcosa,posso postarlo) o il problema e' nelle impostazioni dell'interfaccia xsane :'(

chiedo aiuto!
grazie giorgio
Avatar utente
Tommy David
Prode Principiante
Messaggi: 97
Iscrizione: mercoledì 29 giugno 2005, 14:26
Contatti:

Re: scanner artec e+ pro

Messaggio da Tommy David »

Niente da fare: pure le mie scansioni sono afflitte dalle linee verticali e dalle sfumature blu sulla destra. Ma se è per questo, su Windows da Vista in poi i driver per questo scanner non funzionano più...
forest
Prode Principiante
Messaggi: 129
Iscrizione: sabato 26 novembre 2005, 17:12
Località: UTA

Re: scanner artec e+ pro

Messaggio da forest »

salve a tutti.
vedo che ci sono in giro altri scanners artec..
purtorppo confermo le righe, avevo seguito tempo fa qualcosa
ma poi ho abbandonato, anche perchè non ho più usato lo scanner;
mi sembra di ricordare tuttavia che gli scanner in genere sono tra gli hardware più ostici per linux.
ho riprovato ad usarlo con il gattopardo (11.10) ma le righe ci sono sempre...
risolvo regolando il contrasto dopo aver scannerizzato l'anteprima.
Scrivi risposta

Ritorna a “Driver e periferiche”

Chi c’è in linea

Visualizzano questa sezione: rigoletto e 31 ospiti