[Risolto] Lm-sensors e nomi sensori
- cristian_c
- Accecante Asceta
- Messaggi: 23422
- Iscrizione: lunedì 29 ottobre 2007, 11:31
[Risolto] Lm-sensors e nomi sensori
Salve, ho cercato ma non ho ancora capito come far visualizzare i nomi dei chip sul pc con lm-sensors. In caso lm-sensors non possa visualizzare quest'informazione, c'è un modo alternativo per farlo? ???
Ultima modifica di Mdfalcubo il venerdì 3 febbraio 2012, 19:10, modificato 1 volta in totale.
- Janvitus
- Amministratore
- Messaggi: 18778
- Iscrizione: lunedì 25 aprile 2005, 15:52
- Desktop: GNOME Shell / Xfce
- Sesso: Maschile
- Località: Potenza
- Contatti:
Re: Lm-sensors e nomi sensori
Spiegati un po' meglio, vuoi fare dei nomi personalizzati ai sensori o che?
- cristian_c
- Accecante Asceta
- Messaggi: 23422
- Iscrizione: lunedì 29 ottobre 2007, 11:31
Re: Lm-sensors e nomi sensori
No no, mi interessa conoscere proprio i nomi veri dei chip montati (i sensori) (yes)Janvitus ha scritto: Spiegati un po' meglio, vuoi fare dei nomi personalizzati ai sensori o che?
- Janvitus
- Amministratore
- Messaggi: 18778
- Iscrizione: lunedì 25 aprile 2005, 15:52
- Desktop: GNOME Shell / Xfce
- Sesso: Maschile
- Località: Potenza
- Contatti:
Re: Lm-sensors e nomi sensori
Quando dai "sensors" nel terminale la prima stringa dovrebbe essere il nome del chip che si occupa di queste cose. Il manuale della scheda madre dovrebbe essere ancora più preciso.
- cristian_c
- Accecante Asceta
- Messaggi: 23422
- Iscrizione: lunedì 29 ottobre 2007, 11:31
Re: Lm-sensors e nomi sensori
A me sembra che la prima riguardi il driver utilizzato da lm-sensors. La riga Adapter invece non aiuta. Output:Janvitus ha scritto: Quando dai "sensors" nel terminale la prima stringa dovrebbe essere il nome del chip che si occupa di queste cose. Il manuale della scheda madre dovrebbe essere ancora più preciso.
Codice: Seleziona tutto
sensors
acpitz-virtual-0
Adapter: Virtual device
temp1: +71.0°C (crit = +100.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +71.0°C (high = +100.0°C, crit = +100.0°C)
Core 1: +71.0°C (high = +100.0°C, crit = +100.0°C)
- cristian_c
- Accecante Asceta
- Messaggi: 23422
- Iscrizione: lunedì 29 ottobre 2007, 11:31
Re: Lm-sensors e nomi sensori
Ho dato un'occhiata a http://www.lm-sensors.org/browser/lm-se ... ps/SUMMARY ma non ho trovato traccia della sigla che mi restituisce lm-sensors :-\
- cristian_c
- Accecante Asceta
- Messaggi: 23422
- Iscrizione: lunedì 29 ottobre 2007, 11:31
Re: Lm-sensors e nomi sensori
Quindi forse, leggendo l'output del comando sensors, i nomi dei chip dovrebbero essere coretemp-isa e acpitz-virtual :-\
Il problema è che non trovo traccia di essi neanche nel file /etc/sensors3.conf:
C'è qualcuno che ci capisce qualcosa?
Il problema è che non trovo traccia di essi neanche nel file /etc/sensors3.conf:
Codice: Seleziona tutto
# libsensors configuration file
# -----------------------------
#
# This default configuration file only includes statements which do not
# differ from one mainboard to the next. Only label, compute and set
# statements for internal voltage and temperature sensors are included.
#
# In general, local changes should not be added to this file, but rather
# placed in custom configuration files located in /etc/sensors.d. This
# approach makes further updates much easier.
#
# Such custom configuration files for specific mainboards can be found at
# http://www.lm-sensors.org/wiki/Configurations
#
# It is recommended not to modify this file, but to drop your local
# changes in /etc/sensors.d/. File with names that start with a dot
# are ignored.
chip "lm78-*" "lm79-*" "lm80-*"
label temp1 "M/B Temp"
chip "w83792d-*"
label in0 "VcoreA"
label in1 "VcoreB"
label in6 "+5V"
label in7 "5VSB"
label in8 "Vbat"
set in6_min 5.0 * 0.90
set in6_max 5.0 * 1.10
set in7_min 5.0 * 0.90
set in7_max 5.0 * 1.10
set in8_min 3.0 * 0.90
set in8_max 3.0 * 1.10
chip "w83793-*"
label in0 "VcoreA"
label in1 "VcoreB"
label in7 "+5V"
label in8 "5VSB"
label in9 "Vbat"
set in7_min 5.0 * 0.90
set in7_max 5.0 * 1.10
set in8_min 5.0 * 0.90
set in8_max 5.0 * 1.10
set in9_min 3.0 * 0.90
set in9_max 3.0 * 1.10
chip "w83795g-*" "w83795adg-*"
label in12 "+3.3V"
label in13 "3VSB"
label in14 "Vbat"
set in12_min 3.3 * 0.90
set in12_max 3.3 * 1.10
set in13_min 3.3 * 0.90
set in13_max 3.3 * 1.10
set in14_min 3.0 * 0.90
set in14_max 3.3 * 1.10
chip "via686a-*"
label in0 "Vcore"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in3_min 5.0 * 0.90
set in3_max 5.0 * 1.10
set in4_min 12.0 * 0.90
set in4_max 12.0 * 1.10
chip "adm1025-*" "ne1619-*"
label in1 "Vcore"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "VCC"
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in3_min 5.0 * 0.90
set in3_max 5.0 * 1.10
set in5_min 3.3 * 0.90
set in5_max 3.3 * 1.10
# Depending on how your chip is hardwired, you may or may not have
# +12V readings.
# set in4_min 12.0 * 0.90
# set in4_max 12.0 * 1.10
label temp1 "CPU Temp"
label temp2 "M/B Temp"
chip "lm87-*" "adm1024-*"
label in1 "Vcore"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in3_min 5.0 * 0.90
set in3_max 5.0 * 1.10
set in4_min 12.0 * 0.90
set in4_max 12.0 * 1.10
label temp1 "M/B Temp"
label temp2 "CPU Temp"
chip "it87-*" "it8712-*" "it8716-*" "it8718-*" "it8720-*"
label in8 "Vbat"
chip "fscpos-*" "fscher-*"
#FSC "Hermes"
label in0 "+12V"
label in1 "+5V"
label in2 "Vbat"
label temp1 "CPU Temp"
label temp2 "M/B Temp"
label temp3 "Aux Temp"
chip "fscscy-*"
#FSC "Scylla"
label in0 "+12V"
label in1 "+5V"
label in2 "+3.3V"
label temp1 "CPU0 Temp"
label temp2 "CPU1 Temp"
label temp3 "M/B Temp"
label temp4 "Aux Temp"
chip "fschds-*"
# Fujitsu Technology Solutions, "Hades"-Chip
# Temperatures
label temp1 "CPU Temp"
label temp2 "Super I/O Temp"
label temp3 "System Temp"
# Fans
label fan1 "PSU Fan"
label fan2 "CPU Fan"
label fan3 "System FAN2"
label fan4 "System FAN3"
label fan5 "System FAN4"
# Voltages
label in0 "+12V"
label in1 "+5V"
label in2 "Vbat"
chip "fscsyl-*"
# Fujitsu Technology Solutions, "Syleus"-Chip
# Temperatures
label temp1 "CPU Temp"
label temp4 "Super I/O Temp"
label temp5 "Northbridge Temp"
# Fans
label fan1 "CPU Fan"
label fan2 "System FAN2"
label fan3 "System FAN3"
label fan4 "System FAN4"
label fan7 "PSU Fan"
# Voltages
label in0 "+12V"
label in1 "+5V"
label in2 "Vbat"
label in3 "+3.3V"
label in5 "+3.3V-Aux"
chip "vt1211-*"
label in5 "+3.3V"
label temp2 "SIO Temp"
chip "vt8231-*"
label in5 "+3.3V"
chip "smsc47m192-*"
label in1 "Vcore"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "VCC"
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in3_min 5.0 * 0.90
set in3_max 5.0 * 1.10
set in4_min 12.0 * 0.90
set in4_max 12.0 * 1.10
set in5_min 3.3 * 0.90
set in5_max 3.3 * 1.10
label temp1 "SIO Temp"
chip "lm85-*" "lm85b-*" "lm85c-*" "adm1027-*" "adt7463-*" "adt7468-*" "emc6d100-*" "emc6d102-*"
label in1 "Vcore"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in3_min 5.0 * 0.90
set in3_max 5.0 * 1.10
# Depending on how your chip is hardwired, you may or may not have
# +12V readings.
# set in4_min 12.0 * 0.90
# set in4_max 12.0 * 1.10
label temp2 "M/B Temp"
chip "pc87365-*" "pc87366-*"
# Voltage inputs
label in7 "3VSB"
label in8 "VDD"
label in9 "Vbat"
label in10 "AVDD"
compute in7 @*2, @/2
compute in8 @*2, @/2
compute in10 @*2, @/2
# These are the operating conditions as recommended by National
# Semiconductor
set in7_min 3.0
set in7_max 3.6
set in8_min 3.0
set in8_max 3.6
set in10_min 3.0
set in10_max 3.6
# Depending on the hardware setup, the battery voltage may or may not
# be monitored.
# set in9_min 2.4
# set in9_max 3.6
label temp3 "SIO Temp"
set temp3_min 0
set temp3_max 70
set temp3_crit 85
chip "adm1030-*" "adm1031-*"
label temp1 "M/B Temp"
chip "w83627thf-*"
label in3 "+5V"
label in7 "5VSB"
label in8 "Vbat"
# Internal resistors
compute in3 @ * (1 + 34/51), @ / (1 + 34/51)
compute in7 @ * (1 + 34/51), @ / (1 + 34/51)
set in3_min 5.0 * 0.90
set in3_max 5.0 * 1.10
set in7_min 5.0 * 0.90
set in7_max 5.0 * 1.10
# The battery voltage may or may not be monitored.
# set in8_min 3.0 * 0.90
# set in8_max 3.0 * 1.10
chip "w83627ehf-*" "w83627dhg-*" "w83667hg-*" "nct6775-*" "nct6776-*"
label in0 "Vcore"
label in2 "AVCC"
label in3 "+3.3V"
label in7 "3VSB"
label in8 "Vbat"
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in3_min 3.3 * 0.90
set in3_max 3.3 * 1.10
set in7_min 3.3 * 0.90
set in7_max 3.3 * 1.10
set in8_min 3.0 * 0.90
set in8_max 3.0 * 1.10
chip "w83627uhg-*"
label in2 "AVCC"
label in3 "+5V"
label in7 "5VSB"
label in8 "Vbat"
set in2_min 5.0 * 0.90
set in2_max 5.0 * 1.10
set in3_min 5.0 * 0.90
set in3_max 5.0 * 1.10
set in7_min 5.0 * 0.90
set in7_max 5.0 * 1.10
set in8_min 3.0 * 0.90
set in8_max 3.0 * 1.10
chip "f71805f-*"
label in0 "+3.3V"
set in0_min 3.3 * 0.90
set in0_max 3.3 * 1.10
chip "f71872f-*"
label in0 "+3.3V"
label in9 "Vbat"
label in10 "3VSB"
set in0_min 3.3 * 0.90
set in0_max 3.3 * 1.10
set in9_min 3.0 * 0.90
set in9_max 3.0 * 1.10
set in10_min 3.3 * 0.90
set in10_max 3.3 * 1.10
chip "k8temp-*"
label temp1 "Core0 Temp"
label temp2 "Core0 Temp"
label temp3 "Core1 Temp"
label temp4 "Core1 Temp"
chip "dme1737-*"
label in0 "5VSB"
label in1 "Vcore"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "3VSB"
label in6 "Vbat"
label temp2 "SIO Temp"
set in0_min 5.0 * 0.90
set in0_max 5.0 * 1.10
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in3_min 5.0 * 0.90
set in3_max 5.0 * 1.10
set in4_min 12.0 * 0.90
set in4_max 12.0 * 1.10
set in5_min 3.3 * 0.90
set in5_max 3.3 * 1.10
set in6_min 3.0 * 0.90
set in6_max 3.0 * 1.10
chip "sch311x-*"
label in1 "Vcore"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "3VSB"
label in6 "Vbat"
label temp2 "SIO Temp"
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in3_min 5.0 * 0.90
set in3_max 5.0 * 1.10
set in4_min 12.0 * 0.90
set in4_max 12.0 * 1.10
set in5_min 3.3 * 0.90
set in5_max 3.3 * 1.10
set in6_min 3.0 * 0.90
set in6_max 3.0 * 1.10
chip "sch5027-*"
label in0 "5VSB"
label in1 "Vcore"
label in2 "+3.3V"
label in5 "3VSB"
label in6 "Vbat"
label temp2 "SIO Temp"
set in0_min 5.0 * 0.90
set in0_max 5.0 * 1.10
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in5_min 3.3 * 0.90
set in5_max 3.3 * 1.10
set in6_min 3.0 * 0.90
set in6_max 3.0 * 1.10
chip "sch5127-*"
label in2 "+3.3V"
label in5 "3VSB"
label in6 "Vbat"
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in5_min 3.3 * 0.90
set in5_max 3.3 * 1.10
set in6_min 3.0 * 0.90
set in6_max 3.0 * 1.10
chip "f71808e-*" "f71862fg-*" "f71869-*" "f71882fg-*" \
"f71889fg-*" "f71889ed-*" "f71889a-*"
label in0 "+3.3V"
label in7 "3VSB"
label in8 "Vbat"
compute in0 @*2, @/2
compute in7 @*2, @/2
compute in8 @*2, @/2
chip "f71858fg-*" "f8000-*"
label in0 "+3.3V"
label in1 "3VSB"
label in2 "Vbat"
compute in0 @*2, @/2
compute in1 @*2, @/2
compute in2 @*2, @/2
chip "f81865f-*"
label in0 "+3.3V"
label in5 "3VSB"
label in6 "Vbat"
compute in0 @*2, @/2
compute in5 @*2, @/2
compute in6 @*2, @/2
chip "adt7473-*" "adt7475-*"
label in2 "+3.3V"
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
label temp2 "Board Temp"
chip "adt7476-*" "adt7490-*"
label in1 "Vcore"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in3_min 5.0 * 0.90
set in3_max 5.0 * 1.10
# Depending on how your ADT7476 is hardwired, you may or may not have
# +12V readings.
# set in4_min 12.0 * 0.90
# set in4_max 12.0 * 1.10
label temp2 "M/B Temp"
Re: Lm-sensors e nomi sensori
acpitz-virtual-0 is an unhelpful label for an ACPI thermal zone, probably from an ACPI table at runtime.
io invece ho
atk0110-acpi-0
Adapter: ACPI interface
quindi deve prendere i valori direttamente da ACPI
io invece ho
atk0110-acpi-0
Adapter: ACPI interface
quindi deve prendere i valori direttamente da ACPI
- cristian_c
- Accecante Asceta
- Messaggi: 23422
- Iscrizione: lunedì 29 ottobre 2007, 11:31
Re: Lm-sensors e nomi sensori
paoloci, grazie della risposta A questo punto ci capisco veramente poco ::) Non sono molto pratico dell'argomento :-[paoloci ha scritto:
acpitz-virtual-0 is an unhelpful label for an ACPI thermal zone, probably from an ACPI table at runtime.
io invece ho
atk0110-acpi-0
Adapter: ACPI interface
quindi deve prendere i valori direttamente da ACPI
Re: Lm-sensors e nomi sensori
mi dispiace, anche io non capisco cosa voglia dire virtuale.
O lo prende da ACPI o no
A meno che esista un, per dire thermistor, che comunichi ad ACPI la temperatura.
A questo punto leggo il valore da ACPI, e il virtuale che non comprendo bene
O lo prende da ACPI o no
A meno che esista un, per dire thermistor, che comunichi ad ACPI la temperatura.
A questo punto leggo il valore da ACPI, e il virtuale che non comprendo bene
- cristian_c
- Accecante Asceta
- Messaggi: 23422
- Iscrizione: lunedì 29 ottobre 2007, 11:31
Re: Lm-sensors e nomi sensori
e per quanto riguarda il resto dell'output?paoloci ha scritto: mi dispiace, anche io non capisco cosa voglia dire virtuale.
O lo prende da ACPI o no
A meno che esista un, per dire thermistor, che comunichi ad ACPI la temperatura.
A questo punto leggo il valore da ACPI, e il virtuale che non comprendo bene
Re: Lm-sensors e nomi sensori
Core 0: +71.0°C (high = +100.0°C, crit = +100.0°C)
Core 1: +71.0°C (high = +100.0°C, crit = +100.0°C)
sono le temperature dei due core della CPU
stanno a 70°C e le temperature critiche sono di 100°C
In effetti, non avevo guardato, ma 71° sono un po' altine, anzi decisamente alte.
La ventola come è?
Una cosa seccante dei sensori del tuo PC è che non danno la velocità delle ventole.
sul mia le vedo
Adapter: ACPI interface
Vcore Voltage: +1.26 V (min = +0.85 V, max = +1.60 V)
+3.3 Voltage: +3.28 V (min = +2.97 V, max = +3.63 V)
+5 Voltage: +5.11 V (min = +4.50 V, max = +5.50 V)
+12 Voltage: +11.93 V (min = +10.20 V, max = +13.80 V)
CPU FAN Speed: 1430 RPM (min = 600 RPM)
CPU Temperature: +45.0°C (high = +60.0°C, crit = +95.0°C)
MB Temperature: +37.0°C (high = +45.0°C, crit = +95.0°C)
Core 1: +71.0°C (high = +100.0°C, crit = +100.0°C)
sono le temperature dei due core della CPU
stanno a 70°C e le temperature critiche sono di 100°C
In effetti, non avevo guardato, ma 71° sono un po' altine, anzi decisamente alte.
La ventola come è?
Una cosa seccante dei sensori del tuo PC è che non danno la velocità delle ventole.
sul mia le vedo
Adapter: ACPI interface
Vcore Voltage: +1.26 V (min = +0.85 V, max = +1.60 V)
+3.3 Voltage: +3.28 V (min = +2.97 V, max = +3.63 V)
+5 Voltage: +5.11 V (min = +4.50 V, max = +5.50 V)
+12 Voltage: +11.93 V (min = +10.20 V, max = +13.80 V)
CPU FAN Speed: 1430 RPM (min = 600 RPM)
CPU Temperature: +45.0°C (high = +60.0°C, crit = +95.0°C)
MB Temperature: +37.0°C (high = +45.0°C, crit = +95.0°C)
- cristian_c
- Accecante Asceta
- Messaggi: 23422
- Iscrizione: lunedì 29 ottobre 2007, 11:31
Re: Lm-sensors e nomi sensori
Magari fossero sempre su quei livellipaoloci ha scritto: Core 0: +71.0°C (high = +100.0°C, crit = +100.0°C)
Core 1: +71.0°C (high = +100.0°C, crit = +100.0°C)
sono le temperature dei due core della CPU
stanno a 70°C e le temperature critiche sono di 100°C
In effetti, non avevo guardato, ma 71° sono un po' altine, anzi decisamente alte.
La ventola come è?
Una cosa seccante dei sensori del tuo PC è che non danno la velocità delle ventole.
sul mia le vedo
Adapter: ACPI interface
Vcore Voltage: +1.26 V (min = +0.85 V, max = +1.60 V)
+3.3 Voltage: +3.28 V (min = +2.97 V, max = +3.63 V)
+5 Voltage: +5.11 V (min = +4.50 V, max = +5.50 V)
+12 Voltage: +11.93 V (min = +10.20 V, max = +13.80 V)
CPU FAN Speed: 1430 RPM (min = 600 RPM)
CPU Temperature: +45.0°C (high = +60.0°C, crit = +95.0°C)
MB Temperature: +37.0°C (high = +45.0°C, crit = +95.0°C)
Il problema è che non conosco neanche i nomi dei sensori ::)
P.S. Più la temperatura aumenta e più la ventola gira al massimo (yes)
Ultima modifica di cristian_c il martedì 13 dicembre 2011, 19:04, modificato 1 volta in totale.
- Janvitus
- Amministratore
- Messaggi: 18778
- Iscrizione: lunedì 25 aprile 2005, 15:52
- Desktop: GNOME Shell / Xfce
- Sesso: Maschile
- Località: Potenza
- Contatti:
Re: Lm-sensors e nomi sensori
Allora, forse ho compreso male io la richiesta, ma se tu vuoi sapere il chip che si occupa di monitorare le temperature del pc, lo puoi trovare sul manuale della scheda madre oppure usando sensors-detect. Se invece vuoi visualizzarli, semplicemente non si può fare.
Esempio:
Esempio:
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD Family 10h thermal sensors... No
AMD Family 11h thermal sensors... No
AMD Family 12h and 14h thermal sensors... No
Intel digital thermal sensor... Success!
(driver `coretemp')
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... Yes
Found `ITE IT8718F Super IO Sensors' Success!
(address 0x290, driver `it87')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No
- cristian_c
- Accecante Asceta
- Messaggi: 23422
- Iscrizione: lunedì 29 ottobre 2007, 11:31
Re: Lm-sensors e nomi sensori
1. Come faccio a conoscere il nome della scheda madre (dato che sul sito del produttore del pc non ne trovo traccia)?Janvitus ha scritto: Allora, forse ho compreso male io la richiesta, ma se tu vuoi sapere il chip che si occupa di monitorare le temperature del pc, lo puoi trovare sul manuale della scheda madre oppure usando sensors-detect. Se invece vuoi visualizzarli, semplicemente non si può fare.
Esempio:
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD Family 10h thermal sensors... No
AMD Family 11h thermal sensors... No
AMD Family 12h and 14h thermal sensors... No
Intel digital thermal sensor... Success!
(driver `coretemp')
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... Yes
Found `ITE IT8718F Super IO Sensors' Success!
(address 0x290, driver `it87')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No
2. Ma sensors-detect non sovrascrive la configurazione attuale di lm-sensors?
- Janvitus
- Amministratore
- Messaggi: 18778
- Iscrizione: lunedì 25 aprile 2005, 15:52
- Desktop: GNOME Shell / Xfce
- Sesso: Maschile
- Località: Potenza
- Contatti:
Re: Lm-sensors e nomi sensori
1) Ci sono vari programmi che lo fanno, tipo hwinfo, ma anche lo stesso sensors-detect:
Il risultato non è assicurato però.
2) Puoi sempre interrompere il processo con ctrl+c o scrivere "no" quando vuole scrivere nel file /etc/modules.
Codice: Seleziona tutto
System: Gigabyte Technology Co., Ltd. EP45-UD3R
2) Puoi sempre interrompere il processo con ctrl+c o scrivere "no" quando vuole scrivere nel file /etc/modules.
- cristian_c
- Accecante Asceta
- Messaggi: 23422
- Iscrizione: lunedì 29 ottobre 2007, 11:31
Re: Lm-sensors e nomi sensori
Con hwinfo non ho capito quale fosse la scheda madre. Ho provato a lanciare dmidecode (da root) e ho trovato questa porzione di output:
È questa la parte relativa alla scheda madre? ???
Codice: Seleziona tutto
Handle 0x0002, DMI type 2, 16 bytes
Base Board Information
Manufacturer: Hewlett-Packard
Product Name: 30D9
Version: 83.21
Serial Number: CND8122BNT
Asset Tag: Base Board Asset Tag
Features:
Board is a hosting board
Board is replaceable
Location In Chassis: Base Board Chassis Location
Chassis Handle: 0x0003
Type: Motherboard
Contained Object Handles: 0
- magozurlinux
- Accecante Asceta
- Messaggi: 24913
- Iscrizione: mercoledì 17 marzo 2010, 17:44
- Desktop: ubuntu
- Distribuzione: Ubuntu 22.04.3 LTS x86_64
- Sesso: Maschile
- Località: Pisa
Re: Lm-sensors e nomi sensori
La tua mobo è una HP 30D9.
Da terminale postami questo comando:
Da terminale postami questo comando:
Codice: Seleziona tutto
sudo lshw -short
- cristian_c
- Accecante Asceta
- Messaggi: 23422
- Iscrizione: lunedì 29 ottobre 2007, 11:31
Re: Lm-sensors e nomi sensori
Grazie magozurlinux, consulterò il manuale della scheda madre per scoprire i nomi dei sensori (yes)magozurlinux ha scritto: La tua mobo è una HP 30D9
"Che mondo sarebbe senza Magozurlinux?!" (Cit.)
Non conoscevo questa variante del comando, spettacolare!Da terminale postami questo comando:
Codice: Seleziona tutto
H/W path Device Class Description
======================================================
system Notebook
/0 bus 30D9
/0/0 memory 1MiB BIOS
/0/e processor Intel(R) Pentium(R) Dual CPU T2370
/0/e/f memory 1MiB L2 cache
/0/e/11 memory 32KiB L1 cache
/0/e/0.1 processor Logical CPU
/0/e/0.2 processor Logical CPU
/0/10 memory 32KiB L1 cache
/0/12 memory 2GiB System Memory
/0/12/0 memory 1GiB SODIMM DDR2 Synchronous 533 MHz
/0/12/1 memory 1GiB SODIMM DDR2 Synchronous 533 MHz
/0/100 bridge Mobile PM965/GM965/GL960 Memory Contr
/0/100/2 display Mobile GM965/GL960 Integrated Graphic
/0/100/2.1 display Mobile GM965/GL960 Integrated Graphic
/0/100/1b multimedia 82801H (ICH8 Family) HD Audio Control
/0/100/1c bridge 82801H (ICH8 Family) PCI Express Port
/0/100/1c/0 wlan0 network AR242x / AR542x Wireless Network Adap
/0/100/1d bus 82801H (ICH8 Family) USB UHCI Control
/0/100/1d.1 bus 82801H (ICH8 Family) USB UHCI Control
/0/100/1d.2 bus 82801H (ICH8 Family) USB UHCI Control
/0/100/1d.7 bus 82801H (ICH8 Family) USB2 EHCI Contro
/0/100/1e bridge 82801 Mobile PCI Bridge
/0/100/1e/1 eth0 network RTL-8139/8139C/8139C+
/0/100/1f bridge 82801HEM (ICH8M) LPC Interface Contro
/0/100/1f.2 scsi0 storage 82801HBM/HEM (ICH8M/ICH8M-E) SATA IDE
/0/100/1f.2/0 /dev/sda disk 120GB SAMSUNG HM121HI
/0/100/1f.2/0/1 /dev/sda1 volume 32GiB Windows NTFS volume
/0/100/1f.2/0/2 /dev/sda2 volume 10GiB Windows NTFS volume
/0/100/1f.2/0/3 /dev/sda3 volume 66GiB Extended partition
/0/100/1f.2/0/3/5 /dev/sda5 volume 27GiB Linux filesystem partition
/0/100/1f.2/0/3/6 /dev/sda6 volume 37GiB Linux filesystem partition
/0/100/1f.2/0/3/7 /dev/sda7 volume 953MiB Linux swap / Solaris partition
/0/100/1f.2/1 /dev/cdrom disk CDDVDW TS-L632H
/0/100/1f.3 bus 82801H (ICH8 Family) SMBus Controller
- cristian_c
- Accecante Asceta
- Messaggi: 23422
- Iscrizione: lunedì 29 ottobre 2007, 11:31
Re: Lm-sensors e nomi sensori
Sembrerà strano ma non sono riuscito a trovare il manuale della scheda madre
Chi c’è in linea
Visualizzano questa sezione: Bing [Bot] e 19 ospiti