frequente e fastidioso problema all'avvio di ubuntu 9.04

[nicotto]

Ho appena installato ubuntu 9.04 e ne sono contento. Ho però riscontrato un problema fastidioso. Quando avvio il pc,non appena finisce il bootscreen col logo di ubuntu,spesso GNOME non si avvia,ma esce una schermata che diventa progressivamente sempre più luminosa fino a diventare completamente bianca e costringermi a riavviare di forza. Non riesco a dire con che frequenza ciò accade. A volte devo mi dà questo problema,riavvio e va. Altre volte una volta non basta,mi dà questo problema più e più volte e mi costringe a riavviare molte volte. Ad esempio ieri sono stato una ventina buona di minuti a riavviare. Qualche giorno fa,invece,mi è andata di c**o e si è avviato direttamente. Come se non bastasse,in qualche raro caso,dopo il bootscreen la schermata resta tutta nera e resta accesa la spia della lettura. Ok che il pc lo spengo solo di notte,ma questo problema è quantomeno fastidioso.

[rds4ever]

Ciao,

puoi allegare il syslog, il log di X (Xorg.log) e anche l'output del comando:

Codice: Seleziona tutto

dmesg

Vediamo che problemi ci sono,

Ciao

Riccardo

[nicotto]

Ciao,

puoi allegare il syslog, il log di X (Xorg.log) e anche l'output del comando:

Codice: Seleziona tutto

dmesg

Vediamo che problemi ci sono,

Ciao

Riccardo

l'output di dmesg è:

Codice: Seleziona tutto

[    0.480553] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.480645] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
[    0.483910] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 *10 11)
[    0.484070] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 10 11)
[    0.484211] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 10 *11)
[    0.484353] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 10 *11)
[    0.484485] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 10 *11)
[    0.484609] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 10 *11)
[    0.484733] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 10 11)
[    0.484858] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 10 11) *7
[    0.485007] ACPI: WMI: Mapper loaded
[    0.485270] SCSI subsystem initialized
[    0.485315] libata version 3.00 loaded.
[    0.485377] usbcore: registered new interface driver usbfs
[    0.485400] usbcore: registered new interface driver hub
[    0.485431] usbcore: registered new device driver usb
[    0.485574] PCI: Using ACPI for IRQ routing
[    0.485692] Bluetooth: Core ver 2.13
[    0.485692] NET: Registered protocol family 31
[    0.485692] Bluetooth: HCI device and connection manager initialized
[    0.485692] Bluetooth: HCI socket layer initialized
[    0.485692] NET: Registered protocol family 8
[    0.485692] NET: Registered protocol family 20
[    0.485692] NetLabel: Initializing
[    0.485692] NetLabel:  domain hash size = 128
[    0.485692] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.485692] NetLabel:  unlabeled traffic allowed by default
[    0.485692] AppArmor: AppArmor Filesystem Enabled
[    0.485692] pnp: PnP ACPI init
[    0.485692] ACPI: bus type pnp registered
[    0.492986] pnp: PnP ACPI: found 10 devices
[    0.492989] ACPI: ACPI bus type pnp unregistered
[    0.492996] PnPBIOS: Disabled by ACPI PNP
[    0.493009] system 00:05: iomem range 0xfff80000-0xffffffff has been reserved
[    0.493017] system 00:07: ioport range 0x680-0x6ff has been reserved
[    0.493020] system 00:07: ioport range 0x200-0x20f has been reserved
[    0.493023] system 00:07: ioport range 0x290-0x297 has been reserved
[    0.493026] system 00:07: ioport range 0x1000-0x107f has been reserved
[    0.493029] system 00:07: ioport range 0x1300-0x133f has been reserved
[    0.493032] system 00:07: ioport range 0x77c-0x77f has been reserved
[    0.527783] pci 0000:01:04.0: CardBus bridge, secondary bus 0000:02
[    0.527787] pci 0000:01:04.0:   IO window: 0x00c400-0x00c4ff
[    0.527792] pci 0000:01:04.0:   IO window: 0x00c800-0x00c8ff
[    0.527796] pci 0000:01:04.0:   PREFETCH window: 0xa0000000-0xa3ffffff
[    0.527801] pci 0000:01:04.0:   MEM window: 0xe4000000-0xe7ffffff
[    0.527806] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
[    0.527810] pci 0000:00:1e.0:   IO window: 0xc000-0xdfff
[    0.527816] pci 0000:00:1e.0:   MEM window: 0xe0000000-0xefffffff
[    0.527821] pci 0000:00:1e.0:   PREFETCH window: 0x000000a0000000-0x000000afffffff
[    0.527837] pci 0000:00:1e.0: setting latency timer to 64
[    0.528091] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
[    0.528094] PCI: setting IRQ 5 as level-triggered
[    0.528099] pci 0000:01:04.0: PCI INT A -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
[    0.528106] bus: 00 index 0 io port: [0x00-0xffff]
[    0.528108] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[    0.528111] bus: 01 index 0 io port: [0xc000-0xdfff]
[    0.528114] bus: 01 index 1 mmio: [0xe0000000-0xefffffff]
[    0.528116] bus: 01 index 2 mmio: [0xa0000000-0xafffffff]
[    0.528118] bus: 01 index 3 io port: [0x00-0xffff]
[    0.528121] bus: 01 index 4 mmio: [0x000000-0xffffffff]
[    0.528123] bus: 02 index 0 io port: [0xc400-0xc4ff]
[    0.528126] bus: 02 index 1 io port: [0xc800-0xc8ff]
[    0.528128] bus: 02 index 2 mmio: [0xa0000000-0xa3ffffff]
[    0.528130] bus: 02 index 3 mmio: [0xe4000000-0xe7ffffff]
[    0.528142] NET: Registered protocol family 2
[    0.528293] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.528572] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.528658] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[    0.528740] TCP: Hash tables configured (established 16384 bind 16384)
[    0.528743] TCP reno registered
[    0.528842] NET: Registered protocol family 1
[    0.528993] checking if image is initramfs... it is
[    1.028057] Switched to high resolution mode on CPU 0
[    1.197972] Freeing initrd memory: 7357k freed
[    1.198028] Simple Boot Flag at 0x37 set to 0x1
[    1.198066] cpufreq: No nForce2 chipset.
[    1.198254] audit: initializing netlink socket (disabled)
[    1.198279] type=2000 audit(1241252828.196:1): initialized
[    1.205710] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.207103] VFS: Disk quotas dquot_6.5.1
[    1.207169] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.207905] fuse init (API version 7.10)
[    1.208036] msgmni has been set to 930
[    1.208255] alg: No test for stdrng (krng)
[    1.208271] io scheduler noop registered
[    1.208274] io scheduler anticipatory registered
[    1.208277] io scheduler deadline registered
[    1.208299] io scheduler cfq registered (default)
[    1.208319] pci 0000:00:02.0: Boot video device
[    1.221535] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.221548] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.344101] ACPI: AC Adapter [AC] (on-line)
[    1.441189] ACPI: Battery Slot [BAT0] (battery present)
[    1.441274] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    1.441277] ACPI: Power Button (FF) [PWRF]
[    1.441329] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1
[    1.441336] ACPI: Sleep Button (CM) [SBTN]
[    1.441388] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[    1.447490] ACPI: Lid Switch [LID]
[    1.447693] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[    1.447724] processor ACPI_CPU:00: registered as cooling_device0
[    1.455117] isapnp: Scanning for PnP cards...
[    1.809057] isapnp: No Plug & Play device found
[    1.810545] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.810932] serial 0000:00:1f.6: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
[    1.810941] serial 0000:00:1f.6: PCI INT B disabled
[    1.811791] brd: module loaded
[    1.812232] loop: module loaded
[    1.812342] Fixed MDIO Bus: probed
[    1.812350] PPP generic driver version 2.4.2
[    1.812427] input: Macintosh mouse button emulation as /devices/virtual/input/input3
[    1.812465] Driver 'sd' needs updating - please use bus_type methods
[    1.812478] Driver 'sr' needs updating - please use bus_type methods
[    1.812572] ata_piix 0000:00:1f.1: version 2.12
[    1.812583] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[    1.812844] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[    1.812848] PCI: setting IRQ 11 as level-triggered
[    1.812853] ata_piix 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[    1.812913] ata_piix 0000:00:1f.1: setting latency timer to 64
[    1.813022] scsi0 : ata_piix
[    1.813141] scsi1 : ata_piix
[    1.814463] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1100 irq 14
[    1.814466] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1108 irq 15
[    1.978110] ata1.00: ATA-8: SAMSUNG HM160HC, LQ100-10, max UDMA/100
[    1.978114] ata1.00: 312581808 sectors, multi 16: LBA48 
[    1.994067] ata1.00: configured for UDMA/100
[    2.172384] ata2.00: ATAPI: TOSHIBA DVD-ROM SD-R6112, 1M30, max UDMA/33
[    2.188345] ata2.00: configured for UDMA/33
[    2.189134] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HM160HC  LQ10 PQ: 0 ANSI: 5
[    2.189261] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
[    2.189282] sd 0:0:0:0: [sda] Write Protect is off
[    2.189285] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.189317] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.189399] sd 0:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
[    2.189416] sd 0:0:0:0: [sda] Write Protect is off
[    2.189419] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.189449] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.189454]  sda: sda1 sda2 < sda5 >
[    2.243331] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.243404] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.248851] scsi 1:0:0:0: CD-ROM            TOSHIBA  DVD-ROM SD-R6112 1M30 PQ: 0 ANSI: 5
[    2.256644] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    2.256648] Uniform CD-ROM driver Revision: 3.20
[    2.256774] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.256829] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    2.257607] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.257865] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
[    2.257870] PCI: setting IRQ 10 as level-triggered
[    2.257875] ehci_hcd 0000:00:1d.7: PCI INT D -> Link[LNKH] -> GSI 10 (level, low) -> IRQ 10
[    2.257907] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    2.257912] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    2.257999] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    2.261917] ehci_hcd 0000:00:1d.7: debug port 1
[    2.261924] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
[    2.261934] ehci_hcd 0000:00:1d.7: irq 10, io mem 0xfebff000
[    2.276029] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    2.276126] usb usb1: configuration #1 chosen from 1 choice
[    2.276161] hub 1-0:1.0: USB hub found
[    2.276179] hub 1-0:1.0: 6 ports detected
[    2.276314] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.276341] uhci_hcd: USB Universal Host Controller Interface driver
[    2.276625] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
[    2.276630] uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
[    2.276640] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    2.276643] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.276707] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    2.276730] uhci_hcd 0000:00:1d.0: irq 10, io base 0x00001200
[    2.276823] usb usb2: configuration #1 chosen from 1 choice
[    2.276856] hub 2-0:1.0: USB hub found
[    2.276867] hub 2-0:1.0: 2 ports detected
[    2.277175] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[    2.277179] uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[    2.277187] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    2.277190] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.277245] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    2.277268] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001600
[    2.277360] usb usb3: configuration #1 chosen from 1 choice
[    2.277400] hub 3-0:1.0: USB hub found
[    2.277409] hub 3-0:1.0: 2 ports detected
[    2.277506] uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[    2.277513] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    2.277516] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.277566] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    2.277588] uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001700
[    2.277677] usb usb4: configuration #1 chosen from 1 choice
[    2.277707] hub 4-0:1.0: USB hub found
[    2.277717] hub 4-0:1.0: 2 ports detected
[    2.277858] usbcore: registered new interface driver libusual
[    2.277901] usbcore: registered new interface driver usbserial
[    2.277916] USB Serial support registered for generic
[    2.277934] usbcore: registered new interface driver usbserial_generic
[    2.277937] usbserial: USB Serial Driver core
[    2.277992] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    2.287765] i8042.c: Detected active multiplexing controller, rev 1.1.
[    2.292363] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.292370] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    2.292373] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    2.292376] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    2.292379] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    2.292577] mice: PS/2 mouse device common for all mice
[    2.292812] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    2.292831] rtc0: alarms up to one month, 242 bytes nvram
[    2.292925] device-mapper: uevent: version 1.0.3
[    2.293060] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[    2.293119] device-mapper: multipath: version 1.0.5 loaded
[    2.293123] device-mapper: multipath round-robin: version 1.0.0 loaded
[    2.293229] EISA: Probing bus 0 at eisa.0
[    2.293238] Cannot allocate resource for EISA slot 1
[    2.293266] EISA: Detected 0 cards.
[    2.293346] cpuidle: using governor ladder
[    2.293426] cpuidle: using governor menu
[    2.294018] TCP cubic registered
[    2.294117] NET: Registered protocol family 10
[    2.294589] lo: Disabled Privacy Extensions
[    2.294944] NET: Registered protocol family 17
[    2.294970] Bluetooth: L2CAP ver 2.11
[    2.294972] Bluetooth: L2CAP socket layer initialized
[    2.294975] Bluetooth: SCO (Voice Link) ver 0.6
[    2.294978] Bluetooth: SCO socket layer initialized
[    2.295030] Bluetooth: RFCOMM socket layer initialized
[    2.295043] Bluetooth: RFCOMM TTY layer initialized
[    2.295045] Bluetooth: RFCOMM ver 1.10
[    2.295097] IO APIC resources could be not be allocated.
[    2.295145] Using IPI No-Shortcut mode
[    2.295273] registered taskstats version 1
[    2.295406]   Magic number: 9:913:471
[    2.295502] rtc_cmos 00:03: setting system clock to 2009-05-02 08:27:09 UTC (1241252829)
[    2.295506] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    2.295508] EDD information not available.
[    2.296162] Freeing unused kernel memory: 532k freed
[    2.296284] Write protecting the kernel text: 4128k
[    2.296325] Write protecting the kernel read-only data: 1532k
[    2.330322] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[    2.600045] usb 1-4: new high speed USB device using ehci_hcd and address 2
[    2.734056] usb 1-4: configuration #1 chosen from 1 choice
[    2.945704] Marking TSC unstable due to TSC halts in idle
[    3.045665] natsemi dp8381x driver, version 2.1, Sept 11, 2006
[    3.045668]   originally by Donald Becker <becker@scyld.com>
[    3.045669]   2.4.x kernel port by Jeff Garzik, Tjeerd Mulder
[    3.045953] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
[    3.045959] natsemi 0000:01:02.0: PCI INT A -> Link[LNKE] -> GSI 11 (level, low) -> IRQ 11
[    3.045968] natsemi 0000:01:02.0: setting latency timer to 64
[    3.048403] natsemi eth0: NatSemi DP8381[56] at 0xe0008000 (0000:01:02.0), 00:40:d0:51:03:ff, IRQ 11, port TP.
[    3.077813] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 3
[    3.077818] PCI: setting IRQ 3 as level-triggered
[    3.077824] ohci1394 0000:01:05.0: PCI INT A -> Link[LNKG] -> GSI 3 (level, low) -> IRQ 3
[    3.077830] ohci1394 0000:01:05.0: setting latency timer to 64
[    3.127626] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[3]  MMIO=[e0000000-e00007ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[    3.623623] PM: Starting manual resume from disk
[    3.623628] PM: Resume from partition 8:5
[    3.623630] PM: Checking hibernation image.
[    3.623867] PM: Resume from disk failed.
[    3.679241] kjournald starting.  Commit interval 5 seconds
[    3.679256] EXT3-fs: mounted filesystem with ordered data mode.
[    4.412173] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0040d001001c6684]
[    9.169487] udev: starting version 141
[    9.317121] acpi device:05: registered as cooling_device1
[    9.317446] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:01/input/input5
[    9.352222] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[    9.370162] Linux agpgart interface v0.103
[    9.375208] agpgart-intel 0000:00:00.0: Intel 855GM Chipset
[    9.375383] agpgart-intel 0000:00:00.0: detected 32636K stolen memory
[    9.376969] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xb0000000
[    9.428179] intel_rng: Firmware space is locked read-only. If you can't or
[    9.428183] intel_rng: don't want to disable this in firmware setup, and if
[    9.428184] intel_rng: you are certain that your system has a functional
[    9.428185] intel_rng: RNG, try using the 'no_fwh_detect' option.
[    9.444414] cfg80211: Calling CRDA to update world regulatory domain
[    9.629064] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    9.766773] iTCO_vendor_support: vendor-support=0
[    9.769268] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[    9.769418] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060)
[    9.769519] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    9.842169] input: PC Speaker as /devices/platform/pcspkr/input/input6
[    9.932076] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[   10.180977] cfg80211: World regulatory domain updated:
[   10.180983] 	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   10.180987] 	(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.180990] 	(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.180993] 	(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[   10.180996] 	(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.180999] 	(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[   10.267627] yenta_cardbus 0000:01:04.0: CardBus bridge found [1631:d005]
[   10.267648] yenta_cardbus 0000:01:04.0: Using CSCINT to route CSC interrupts to PCI
[   10.267651] yenta_cardbus 0000:01:04.0: Routing CardBus interrupts to PCI
[   10.267656] yenta_cardbus 0000:01:04.0: TI: mfunc 0x010c1202, devctl 0x44
[   10.371648] usb 1-4: reset high speed USB device using ehci_hcd and address 2
[   10.439497] Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
[   10.439650] Intel ICH 0000:00:1f.5: setting latency timer to 64
[   10.496780] yenta_cardbus 0000:01:04.0: ISA IRQ mask 0x0010, PCI irq 5
[   10.496786] yenta_cardbus 0000:01:04.0: Socket status: 30000006
[   10.496790] pci_bus 0000:01: Raising subordinate bus# of parent bus (#01) from #01 to #05
[   10.496801] yenta_cardbus 0000:01:04.0: pcmcia: parent PCI bridge I/O window: 0xc000 - 0xdfff
[   10.496805] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc000-0xdfff: clean.
[   10.497248] yenta_cardbus 0000:01:04.0: pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xefffffff
[   10.497252] yenta_cardbus 0000:01:04.0: pcmcia: parent PCI bridge Memory window: 0xa0000000 - 0xafffffff
[   10.505953] phy0: Selected rate control algorithm 'pid'
[   10.559733] zd1211rw 1-4:1.0: phy0
[   10.559771] usbcore: registered new interface driver zd1211rw
[   10.830290] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: excluding 0x378-0x37f
[   10.831993] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[   10.832782] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[   10.833422] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[   10.834234] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[   10.959511] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x8f6eb3, caps: 0x804713/0x0
[   11.024132] Clocksource tsc unstable (delta = -310185769 ns)
[   11.031538] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio3/input/input7
[   11.264051] intel8x0_measure_ac97_clock: measured 55211 usecs
[   11.264055] intel8x0: clocking to 48000
[   11.495541] lp: driver loaded but no devices found
[   11.604339] Adding 1397612k swap on /dev/sda5.  Priority:-1 extents:1 across:1397612k
[   12.266037] EXT3 FS on sda1, internal journal
[   13.514105] type=1505 audit(1241252840.716:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=1974
[   13.574402] type=1505 audit(1241252840.776:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1978
[   13.574631] type=1505 audit(1241252840.776:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1978
[   13.574703] type=1505 audit(1241252840.776:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1978
[   13.574761] type=1505 audit(1241252840.776:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1978
[   13.758350] type=1505 audit(1241252840.960:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1983
[   13.758659] type=1505 audit(1241252840.960:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1983
[   13.804892] type=1505 audit(1241252841.008:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1998
[   16.382547] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   16.382552] Bluetooth: BNEP filters: protocol multicast
[   16.411017] Bridge firewalling registered
[   17.697681] ppdev: user-space parallel port driver
[   18.361026] [drm] Initialized drm 1.1.0 20060810
[   18.417167] pci 0000:00:02.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
[   18.417175] pci 0000:00:02.0: setting latency timer to 64
[   18.417387] [drm] Initialized i915 1.6.0 20080730 on minor 0
[   18.523456] [drm:i915_setparam] *ERROR* unknown parameter 4
[   18.523493] [drm:i915_getparam] *ERROR* Unknown parameter 6
[   19.274907] [drm:i915_getparam] *ERROR* Unknown parameter 6
[   28.267076] [drm:i915_getparam] *ERROR* Unknown parameter 6
[  114.906492] NET: Registered protocol family 24
[  116.217965] eth0: DSPCFG accepted after 0 usec.
[  116.217975] eth0: link up.
[  116.217985] eth0: Setting full-duplex based on negotiated link capability.
[  126.944151] eth0: no IPv6 routers present
[  132.772062] ip_tables: (C) 2000-2006 Netfilter Core Team
[  165.821606] ACPI: EC: GPE storm detected, transactions will use polling mode
[  310.485100] [drm:i915_getparam] *ERROR* Unknown parameter 6
[ 1244.001986] usb 1-4: firmware: requesting zd1211/zd1211b_ub
[ 1244.312339] usb 1-4: firmware: requesting zd1211/zd1211b_uphr
[ 1244.469485] zd1211rw 1-4:1.0: firmware version 4725
[ 1244.509483] zd1211rw 1-4:1.0: zd1211b chip 0ace:1215 v4810 high 00-19-e0 UW2453_RF pa0 -7---
[ 1244.511982] cfg80211: Calling CRDA for country: DE
[ 1244.564089] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1244.721291] cfg80211: Regulatory domain changed to country: DE
[ 1244.721298] 	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 1244.721301] 	(2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 1244.721304] 	(5150000 KHz - 5255000 KHz @ 40000 KHz), (N/A, 2301 mBm)
[ 1244.721307] 	(5470000 KHz - 5650000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 1246.100461] eth0: remaining active for wake-on-lan
[ 1247.423122] eth0: DSPCFG accepted after 0 usec.
[ 1247.423132] eth0: link up.
[ 1247.423151] eth0: Setting full-duplex based on negotiated link capability.
[ 1258.172039] eth0: no IPv6 routers present
[ 1285.234884] eth0: Autonegotiation advertising 0x5e1  partner 0x00.
[ 1285.234891] eth0: link down.
[ 1310.045233] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1311.255186] wlan0: authenticate with AP 00:08:27:9a:47:fa
[ 1311.276186] wlan0: authenticate with AP 00:08:27:9a:47:fa
[ 1311.276210] wlan0: authenticated
[ 1311.276213] wlan0: associate with AP 00:08:27:9a:47:fa
[ 1311.281303] wlan0: RX AssocResp from 00:08:27:9a:47:fa (capab=0x421 status=0 aid=1)
[ 1311.281307] wlan0: associated
[ 1311.281725] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1321.764039] wlan0: no IPv6 routers present
[ 1352.692295] wlan0: deauthenticating by local choice (reason=3)
[ 1386.206727] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1387.290669] wlan0: authenticate with AP 00:08:27:9a:47:fa
[ 1387.313673] wlan0: authenticate with AP 00:08:27:9a:47:fa
[ 1387.313705] wlan0: authenticated
[ 1387.313709] wlan0: associate with AP 00:08:27:9a:47:fa
[ 1387.319044] wlan0: RX AssocResp from 00:08:27:9a:47:fa (capab=0x421 status=0 aid=1)
[ 1387.319048] wlan0: associated
[ 1387.319484] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 1395.268661] eth0: remaining active for wake-on-lan
[ 1395.274459] eth0: DSPCFG accepted after 0 usec.
[ 1395.274571] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1397.892037] wlan0: no IPv6 routers present
[ 1454.192032] pan0: no IPv6 routers present
[ 1678.737588] usb 1-4: USB disconnect, address 2
[ 1678.746599] zd1211rw 1-4:1.0: error ioread32(CR_REG1): -22
[ 1964.764049] usb 2-2: new low speed USB device using uhci_hcd and address 2
[ 1964.920711] usb 2-2: configuration #1 chosen from 1 choice
[ 1965.037344] usbcore: registered new interface driver hiddev
[ 1965.050645] input: HID 062a:0000 as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input8
[ 1965.051061] generic-usb 0003:062A:0000.0001: input,hidraw0: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:1d.0-2/input0
[ 1965.051086] usbcore: registered new interface driver usbhid
[ 1965.051090] usbhid: v2.6:USB HID core driver
[ 3267.668068] usb 1-6: new high speed USB device using ehci_hcd and address 4
[ 3267.807785] usb 1-6: configuration #1 chosen from 1 choice
[ 3267.907784] Initializing USB Mass Storage driver...
[ 3267.909596] scsi2 : SCSI emulation for USB Mass Storage devices
[ 3267.909919] usbcore: registered new interface driver usb-storage
[ 3267.909926] USB Mass Storage support registered.
[ 3267.911115] usb-storage: device found at 4
[ 3267.911120] usb-storage: waiting for device to settle before scanning
[ 3272.908197] usb-storage: device scan complete
[ 3272.976587] scsi 2:0:0:0: Direct-Access     ST916082 1AS                   PQ: 0 ANSI: 2 CCS
[ 3272.979402] sd 2:0:0:0: [sdb] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
[ 3273.027467] sd 2:0:0:0: [sdb] Write Protect is off
[ 3273.027473] sd 2:0:0:0: [sdb] Mode Sense: 00 38 00 00
[ 3273.027476] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 3273.028993] sd 2:0:0:0: [sdb] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
[ 3273.030706] sd 2:0:0:0: [sdb] Write Protect is off
[ 3273.030712] sd 2:0:0:0: [sdb] Mode Sense: 00 38 00 00
[ 3273.030715] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 3273.030724]  sdb: sdb1
[ 3273.042085] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 3273.042183] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 8977.166972] [drm:i915_getparam] *ERROR* Unknown parameter 6
[10020.824047] usb 1-5: new high speed USB device using ehci_hcd and address 5
[10020.957284] usb 1-5: configuration #1 chosen from 1 choice
[10021.072063] usb 1-5: reset high speed USB device using ehci_hcd and address 5
[10021.236216] phy1: Selected rate control algorithm 'pid'
[10021.237249] zd1211rw 1-5:1.0: phy1
[10021.299215] usb 1-5: firmware: requesting zd1211/zd1211b_ub
[10021.405515] usb 1-5: firmware: requesting zd1211/zd1211b_uphr
[10021.663764] zd1211rw 1-5:1.0: firmware version 4725
[10021.704774] zd1211rw 1-5:1.0: zd1211b chip 0ace:1215 v4810 high 00-19-e0 UW2453_RF pa0 -7---
[10021.707265] cfg80211: Calling CRDA for country: DE
[10021.738328] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[10025.106393] wlan0: authenticate with AP 00:08:27:9a:47:fa
[10025.107877] wlan0: authenticated
[10025.107881] wlan0: associate with AP 00:08:27:9a:47:fa
[10025.112143] wlan0: RX AssocResp from 00:08:27:9a:47:fa (capab=0x421 status=0 aid=1)
[10025.112147] wlan0: associated
[10025.112481] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[10035.496044] wlan0: no IPv6 routers present
[10037.848935] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[10037.878329] wlan0: deauthenticating by local choice (reason=3)
[10038.081876] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[10040.161893] wlan0: authenticate with AP 00:08:27:9a:47:fa
[10040.163371] wlan0: authenticated
[10040.163375] wlan0: associate with AP 00:08:27:9a:47:fa
[10040.167384] wlan0: RX AssocResp from 00:08:27:9a:47:fa (capab=0x421 status=0 aid=1)
[10040.167388] wlan0: associated
[10040.167743] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[10050.176032] wlan0: no IPv6 routers present
[12169.279527] [drm:i915_getparam] *ERROR* Unknown parameter 6

Per il resto,dovresti dirmi dove prenderli (parlando da straniubbo quale sono :-[)

[rds4ever]

Ciao,

grazie. Sto guardando l'output del comando dmesg.

Per il resto,dovresti dirmi dove prenderli

Nessun problema . Per il syslog e il file di log di X, vai sotto /var/log.

Ciao

Riccardo

[nicotto]

questo è il syslog:

Codice: Seleziona tutto

May  2 11:02:58 nico-laptop syslogd 1.5.0#5ubuntu3: restart.
May  2 11:10:02 nico-laptop /USR/SBIN/CRON[10162]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 11:17:01 nico-laptop /USR/SBIN/CRON[11378]: (root) CMD (   cd / && run-parts --report /etc/cron.hourly)
May  2 11:20:01 nico-laptop /USR/SBIN/CRON[11937]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 11:21:34 nico-laptop kernel: [ 3267.668068] usb 1-6: new high speed USB device using ehci_hcd and address 4
May  2 11:21:35 nico-laptop kernel: [ 3267.807785] usb 1-6: configuration #1 chosen from 1 choice
May  2 11:21:35 nico-laptop kernel: [ 3267.907784] Initializing USB Mass Storage driver...
May  2 11:21:35 nico-laptop kernel: [ 3267.909596] scsi2 : SCSI emulation for USB Mass Storage devices
May  2 11:21:35 nico-laptop kernel: [ 3267.909919] usbcore: registered new interface driver usb-storage
May  2 11:21:35 nico-laptop kernel: [ 3267.909926] USB Mass Storage support registered.
May  2 11:21:35 nico-laptop kernel: [ 3267.911115] usb-storage: device found at 4
May  2 11:21:35 nico-laptop kernel: [ 3267.911120] usb-storage: waiting for device to settle before scanning
May  2 11:21:40 nico-laptop kernel: [ 3272.908197] usb-storage: device scan complete
May  2 11:21:40 nico-laptop kernel: [ 3272.976587] scsi 2:0:0:0: Direct-Access     ST916082 1AS                   PQ: 0 ANSI: 2 CCS
May  2 11:21:40 nico-laptop kernel: [ 3272.979402] sd 2:0:0:0: [sdb] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
May  2 11:21:40 nico-laptop kernel: [ 3273.027467] sd 2:0:0:0: [sdb] Write Protect is off
May  2 11:21:40 nico-laptop kernel: [ 3273.027473] sd 2:0:0:0: [sdb] Mode Sense: 00 38 00 00
May  2 11:21:40 nico-laptop kernel: [ 3273.027476] sd 2:0:0:0: [sdb] Assuming drive cache: write through
May  2 11:21:40 nico-laptop kernel: [ 3273.028993] sd 2:0:0:0: [sdb] 312581808 512-byte hardware sectors: (160 GB/149 GiB)
May  2 11:21:40 nico-laptop kernel: [ 3273.030706] sd 2:0:0:0: [sdb] Write Protect is off
May  2 11:21:40 nico-laptop kernel: [ 3273.030712] sd 2:0:0:0: [sdb] Mode Sense: 00 38 00 00
May  2 11:21:40 nico-laptop kernel: [ 3273.030715] sd 2:0:0:0: [sdb] Assuming drive cache: write through
May  2 11:21:40 nico-laptop kernel: [ 3273.030724]  sdb: sdb1
May  2 11:21:40 nico-laptop kernel: [ 3273.042085] sd 2:0:0:0: [sdb] Attached SCSI disk
May  2 11:21:40 nico-laptop kernel: [ 3273.042183] sd 2:0:0:0: Attached scsi generic sg2 type 0
May  2 11:21:41 nico-laptop hald: mounted /dev/sdb1 on behalf of uid 1000
May  2 11:30:02 nico-laptop /USR/SBIN/CRON[13687]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 11:40:01 nico-laptop /USR/SBIN/CRON[15306]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 11:50:01 nico-laptop /USR/SBIN/CRON[16890]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 12:00:01 nico-laptop /USR/SBIN/CRON[18476]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd hourly 2>/dev/null)
May  2 12:00:01 nico-laptop /USR/SBIN/CRON[18490]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 12:10:01 nico-laptop /USR/SBIN/CRON[20119]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 12:17:01 nico-laptop /USR/SBIN/CRON[21286]: (root) CMD (   cd / && run-parts --report /etc/cron.hourly)
May  2 12:20:01 nico-laptop /USR/SBIN/CRON[21846]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 12:30:01 nico-laptop /USR/SBIN/CRON[23430]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 12:40:02 nico-laptop /USR/SBIN/CRON[25014]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 12:50:01 nico-laptop /USR/SBIN/CRON[26651]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 12:56:44 nico-laptop kernel: [ 8977.166972] [drm:i915_getparam] *ERROR* Unknown parameter 6
May  2 13:00:01 nico-laptop /USR/SBIN/CRON[28286]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 13:00:01 nico-laptop /USR/SBIN/CRON[28289]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd hourly 2>/dev/null)
May  2 13:10:01 nico-laptop /USR/SBIN/CRON[30017]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 13:14:08 nico-laptop kernel: [10020.824047] usb 1-5: new high speed USB device using ehci_hcd and address 5
May  2 13:14:08 nico-laptop kernel: [10020.957284] usb 1-5: configuration #1 chosen from 1 choice
May  2 13:14:08 nico-laptop kernel: [10021.072063] usb 1-5: reset high speed USB device using ehci_hcd and address 5
May  2 13:14:08 nico-laptop kernel: [10021.236216] phy1: Selected rate control algorithm 'pid'
May  2 13:14:08 nico-laptop kernel: [10021.237249] zd1211rw 1-5:1.0: phy1
May  2 13:14:08 nico-laptop kernel: [10021.299215] usb 1-5: firmware: requesting zd1211/zd1211b_ub
May  2 13:14:08 nico-laptop kernel: [10021.405515] usb 1-5: firmware: requesting zd1211/zd1211b_uphr
May  2 13:14:08 nico-laptop kernel: [10021.663764] zd1211rw 1-5:1.0: firmware version 4725
May  2 13:14:08 nico-laptop kernel: [10021.704774] zd1211rw 1-5:1.0: zd1211b chip 0ace:1215 v4810 high 00-19-e0 UW2453_RF pa0 -7---
May  2 13:14:08 nico-laptop kernel: [10021.707265] cfg80211: Calling CRDA for country: DE
May  2 13:14:08 nico-laptop kernel: [10021.738328] ADDRCONF(NETDEV_UP): wlan0: link is not ready
May  2 13:14:09 nico-laptop ntpdate[30885]: can't find host ntp.ubuntu.com 
May  2 13:14:09 nico-laptop ntpdate[30885]: no servers can be used, exiting
May  2 13:14:12 nico-laptop kernel: [10025.106393] wlan0: authenticate with AP 00:08:27:9a:47:fa
May  2 13:14:12 nico-laptop kernel: [10025.107877] wlan0: authenticated
May  2 13:14:12 nico-laptop kernel: [10025.107881] wlan0: associate with AP 00:08:27:9a:47:fa
May  2 13:14:12 nico-laptop kernel: [10025.112143] wlan0: RX AssocResp from 00:08:27:9a:47:fa (capab=0x421 status=0 aid=1)
May  2 13:14:12 nico-laptop kernel: [10025.112147] wlan0: associated
May  2 13:14:12 nico-laptop kernel: [10025.112481] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
May  2 13:14:13 nico-laptop avahi-daemon[2657]: Registering new address record for fe80::219:e0ff:fe67:b088 on wlan0.*.
May  2 13:14:22 nico-laptop kernel: [10035.496044] wlan0: no IPv6 routers present
May  2 13:14:24 nico-laptop avahi-daemon[2657]: Withdrawing address record for fe80::219:e0ff:fe67:b088 on wlan0.
May  2 13:14:24 nico-laptop dhclient: Internet Systems Consortium DHCP Client V3.1.1
May  2 13:14:24 nico-laptop dhclient: Copyright 2004-2008 Internet Systems Consortium.
May  2 13:14:24 nico-laptop dhclient: All rights reserved.
May  2 13:14:24 nico-laptop dhclient: For info, please visit http://www.isc.org/sw/dhcp/
May  2 13:14:24 nico-laptop dhclient: 
May  2 13:14:24 nico-laptop dhclient: wmaster0: unknown hardware address type 801
May  2 13:14:24 nico-laptop dhclient: wmaster0: unknown hardware address type 801
May  2 13:14:24 nico-laptop dhclient: Bind socket to interface: No such device
May  2 13:14:24 nico-laptop dhclient: Internet Systems Consortium DHCP Client V3.1.1
May  2 13:14:24 nico-laptop dhclient: Copyright 2004-2008 Internet Systems Consortium.
May  2 13:14:24 nico-laptop dhclient: All rights reserved.
May  2 13:14:24 nico-laptop dhclient: For info, please visit http://www.isc.org/sw/dhcp/
May  2 13:14:24 nico-laptop dhclient: 
May  2 13:14:24 nico-laptop dhclient: wmaster0: unknown hardware address type 801
May  2 13:14:24 nico-laptop dhclient: wmaster0: unknown hardware address type 801
May  2 13:14:24 nico-laptop dhclient: Bind socket to interface: No such device
May  2 13:14:25 nico-laptop kernel: [10037.848935] ADDRCONF(NETDEV_UP): wlan0: link is not ready
May  2 13:14:25 nico-laptop kernel: [10037.878329] wlan0: deauthenticating by local choice (reason=3)
May  2 13:14:25 nico-laptop kernel: [10038.081876] ADDRCONF(NETDEV_UP): wlan0: link is not ready
May  2 13:14:27 nico-laptop kernel: [10040.161893] wlan0: authenticate with AP 00:08:27:9a:47:fa
May  2 13:14:27 nico-laptop kernel: [10040.163371] wlan0: authenticated
May  2 13:14:27 nico-laptop kernel: [10040.163375] wlan0: associate with AP 00:08:27:9a:47:fa
May  2 13:14:27 nico-laptop kernel: [10040.167384] wlan0: RX AssocResp from 00:08:27:9a:47:fa (capab=0x421 status=0 aid=1)
May  2 13:14:27 nico-laptop kernel: [10040.167388] wlan0: associated
May  2 13:14:27 nico-laptop kernel: [10040.167743] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
May  2 13:14:27 nico-laptop dhclient: Internet Systems Consortium DHCP Client V3.1.1
May  2 13:14:27 nico-laptop dhclient: Copyright 2004-2008 Internet Systems Consortium.
May  2 13:14:27 nico-laptop dhclient: All rights reserved.
May  2 13:14:27 nico-laptop dhclient: For info, please visit http://www.isc.org/sw/dhcp/
May  2 13:14:27 nico-laptop dhclient: 
May  2 13:14:27 nico-laptop dhclient: wmaster0: unknown hardware address type 801
May  2 13:14:28 nico-laptop avahi-daemon[2657]: Registering new address record for fe80::219:e0ff:fe67:b088 on wlan0.*.
May  2 13:14:28 nico-laptop dhclient: wmaster0: unknown hardware address type 801
May  2 13:14:28 nico-laptop dhclient: Listening on LPF/wlan0/00:19:e0:67:b0:88
May  2 13:14:28 nico-laptop dhclient: Sending on   LPF/wlan0/00:19:e0:67:b0:88
May  2 13:14:28 nico-laptop dhclient: Sending on   Socket/fallback
May  2 13:14:29 nico-laptop dhclient: DHCPREQUEST of 192.168.1.5 on wlan0 to 255.255.255.255 port 67
May  2 13:14:29 nico-laptop dhclient: DHCPNAK from 192.168.1.1
May  2 13:14:29 nico-laptop avahi-autoipd(wlan0)[30957]: Found user 'avahi-autoipd' (UID 104) and group 'avahi-autoipd' (GID 110).
May  2 13:14:29 nico-laptop avahi-autoipd(wlan0)[30957]: Successfully called chroot().
May  2 13:14:29 nico-laptop avahi-autoipd(wlan0)[30957]: Successfully dropped root privileges.
May  2 13:14:29 nico-laptop avahi-autoipd(wlan0)[30957]: Starting with address 169.254.8.119
May  2 13:14:34 nico-laptop avahi-autoipd(wlan0)[30957]: Callout BIND, address 169.254.8.119 on interface wlan0
May  2 13:14:34 nico-laptop avahi-daemon[2657]: Joining mDNS multicast group on interface wlan0.IPv4 with address 169.254.8.119.
May  2 13:14:34 nico-laptop avahi-daemon[2657]: New relevant interface wlan0.IPv4 for mDNS.
May  2 13:14:34 nico-laptop avahi-daemon[2657]: Registering new address record for 169.254.8.119 on wlan0.IPv4.
May  2 13:14:37 nico-laptop kernel: [10050.176032] wlan0: no IPv6 routers present
May  2 13:14:38 nico-laptop avahi-autoipd(wlan0)[30957]: Successfully claimed IP address 169.254.8.119
May  2 13:14:38 nico-laptop avahi-autoipd(wlan0)[30957]: Got SIGTERM, quitting.
May  2 13:14:38 nico-laptop avahi-autoipd(wlan0)[30957]: Callout STOP, address 169.254.8.119 on interface wlan0
May  2 13:14:38 nico-laptop avahi-daemon[2657]: Withdrawing address record for 169.254.8.119 on wlan0.
May  2 13:14:38 nico-laptop avahi-daemon[2657]: Leaving mDNS multicast group on interface wlan0.IPv4 with address 169.254.8.119.
May  2 13:14:38 nico-laptop avahi-daemon[2657]: Interface wlan0.IPv4 no longer relevant for mDNS.
May  2 13:14:38 nico-laptop avahi-autoipd(wlan0)[30958]: client: RTNETLINK answers: No such process
May  2 13:14:39 nico-laptop dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7
May  2 13:14:39 nico-laptop dhclient: DHCPOFFER of 192.168.1.5 from 192.168.1.1
May  2 13:14:39 nico-laptop dhclient: DHCPREQUEST of 192.168.1.5 on wlan0 to 255.255.255.255 port 67
May  2 13:14:39 nico-laptop dhclient: DHCPACK of 192.168.1.5 from 192.168.1.1
May  2 13:14:39 nico-laptop avahi-daemon[2657]: Joining mDNS multicast group on interface wlan0.IPv4 with address 192.168.1.5.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: New relevant interface wlan0.IPv4 for mDNS.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: Registering new address record for 192.168.1.5 on wlan0.IPv4.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: Withdrawing address record for 192.168.1.5 on wlan0.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: Leaving mDNS multicast group on interface wlan0.IPv4 with address 192.168.1.5.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: Interface wlan0.IPv4 no longer relevant for mDNS.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: Joining mDNS multicast group on interface wlan0.IPv4 with address 192.168.1.5.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: New relevant interface wlan0.IPv4 for mDNS.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: Registering new address record for 192.168.1.5 on wlan0.IPv4.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: Withdrawing address record for 192.168.1.5 on wlan0.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: Leaving mDNS multicast group on interface wlan0.IPv4 with address 192.168.1.5.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: Interface wlan0.IPv4 no longer relevant for mDNS.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: Joining mDNS multicast group on interface wlan0.IPv4 with address 192.168.1.5.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: New relevant interface wlan0.IPv4 for mDNS.
May  2 13:14:39 nico-laptop avahi-daemon[2657]: Registering new address record for 192.168.1.5 on wlan0.IPv4.
May  2 13:14:40 nico-laptop dhclient: bound to 192.168.1.5 -- renewal in 7366 seconds.
May  2 13:15:10 nico-laptop pppd[31065]: Plugin rp-pppoe.so loaded.
May  2 13:15:10 nico-laptop pppd[31065]: RP-PPPoE plugin version 3.8p compiled against pppd 2.4.5
May  2 13:15:10 nico-laptop pppd[31067]: pppd 2.4.5 started by root, uid 0
May  2 13:15:10 nico-laptop pppd[31067]: PPP session is 20983
May  2 13:15:10 nico-laptop pppd[31067]: Connected to 00:11:5c:3d:46:91 via interface wlan0
May  2 13:15:10 nico-laptop pppd[31067]: Using interface ppp0
May  2 13:15:10 nico-laptop pppd[31067]: Connect: ppp0 <--> wlan0
May  2 13:15:11 nico-laptop pppd[31067]: PAP authentication succeeded
May  2 13:15:11 nico-laptop pppd[31067]: peer from calling number 00:11:5C:3D:46:91 authorized
May  2 13:15:11 nico-laptop pppd[31067]: replacing old default route to wlan0 [192.168.1.1]
May  2 13:15:11 nico-laptop pppd[31067]: Cannot determine ethernet address for proxy ARP
May  2 13:15:11 nico-laptop pppd[31067]: local  IP address 82.59.106.212
May  2 13:15:11 nico-laptop pppd[31067]: remote IP address 192.168.100.1
May  2 13:15:11 nico-laptop pppd[31067]: primary   DNS address 85.37.17.9
May  2 13:15:11 nico-laptop pppd[31067]: secondary DNS address 85.38.28.75
May  2 13:17:01 nico-laptop /USR/SBIN/CRON[31194]: (root) CMD (   cd / && run-parts --report /etc/cron.hourly)
May  2 13:20:01 nico-laptop /USR/SBIN/CRON[31497]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 13:30:02 nico-laptop /USR/SBIN/CRON[32237]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 13:40:01 nico-laptop /USR/SBIN/CRON[428]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 13:49:56 nico-laptop kernel: [12169.279527] [drm:i915_getparam] *ERROR* Unknown parameter 6
May  2 13:50:01 nico-laptop /USR/SBIN/CRON[1075]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 14:00:01 nico-laptop /USR/SBIN/CRON[1729]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd hourly 2>/dev/null)
May  2 14:00:01 nico-laptop /USR/SBIN/CRON[1732]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 14:10:01 nico-laptop /USR/SBIN/CRON[2627]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 14:17:01 nico-laptop /USR/SBIN/CRON[3192]: (root) CMD (   cd / && run-parts --report /etc/cron.hourly)
May  2 14:20:01 nico-laptop /USR/SBIN/CRON[3495]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 14:30:01 nico-laptop /USR/SBIN/CRON[4188]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 14:40:01 nico-laptop /USR/SBIN/CRON[4925]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 14:50:01 nico-laptop /USR/SBIN/CRON[5708]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 15:00:02 nico-laptop /USR/SBIN/CRON[6739]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd hourly 2>/dev/null)
May  2 15:00:02 nico-laptop /USR/SBIN/CRON[6740]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 15:02:33 nico-laptop kernel: [16526.412819] [drm:i915_getparam] *ERROR* Unknown parameter 6
May  2 15:10:02 nico-laptop /USR/SBIN/CRON[7784]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 15:17:03 nico-laptop /USR/SBIN/CRON[8373]: (root) CMD (   cd / && run-parts --report /etc/cron.hourly)
May  2 15:17:26 nico-laptop dhclient: DHCPREQUEST of 192.168.1.5 on wlan0 to 192.168.1.1 port 67
May  2 15:17:26 nico-laptop dhclient: DHCPACK of 192.168.1.5 from 192.168.1.1
May  2 15:17:27 nico-laptop dhclient: bound to 192.168.1.5 -- renewal in 8628 seconds.
May  2 15:20:07 nico-laptop /USR/SBIN/CRON[8665]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 15:30:08 nico-laptop /USR/SBIN/CRON[9436]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)
May  2 15:40:01 nico-laptop /USR/SBIN/CRON[10180]: (root) CMD ([ -x /usr/sbin/update-motd ] && /usr/sbin/update-motd 2>/dev/null)

[nicotto]

E questo dovrebbe essere il log di Xorg(Non so se è quello perchè si chiama Xorg.0.log e non Xorg.log):

Codice: Seleziona tutto

X.Org X Server 1.6.0
Release Date: 2009-2-25
X Protocol Version 11, Revision 0
Build Operating System: Linux 2.6.24-23-server i686 Ubuntu
Current Operating System: Linux nico-laptop 2.6.28-11-generic #42-Ubuntu SMP Fri Apr 17 01:57:59 UTC 2009 i686
Build Date: 09 April 2009  02:10:02AM
xorg-server 2:1.6.0-0ubuntu14 (buildd@rothera.buildd) 
	Before reporting problems, check http://wiki.x.org
	to make sure that you have the latest version.
Markers: (--) probed, (**) from config file, (==) default setting,
	(++) from command line, (!!) notice, (II) informational,
	(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Sat May  2 10:27:24 2009
(==) Using config file: "/etc/X11/xorg.conf"
(==) No Layout section.  Using the first Screen section.
(**) |-->Screen "Default Screen" (0)
(**) |   |-->Monitor "Configured Monitor"
(**) |   |-->Device "Configured Video Device"
(==) Automatically adding devices
(==) Automatically enabling devices
(WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist.
	Entry deleted from font path.
(==) FontPath set to:
	/usr/share/fonts/X11/misc,
	/usr/share/fonts/X11/100dpi/:unscaled,
	/usr/share/fonts/X11/75dpi/:unscaled,
	/usr/share/fonts/X11/Type1,
	/usr/share/fonts/X11/100dpi,
	/usr/share/fonts/X11/75dpi,
	/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType,
	built-ins
(==) ModulePath set to "/usr/lib/xorg/modules"
(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
	If no devices become available, reconfigure HAL or disable AllowEmptyInput.
(II) Loader magic: 0x3bc0
(II) Module ABI versions:
	X.Org ANSI C Emulation: 0.4
	X.Org Video Driver: 5.0
	X.Org XInput driver : 4.0
	X.Org Server Extension : 2.0
(II) Loader running on linux
(++) using VT number 7

(--) PCI:*(0@0:2:0) Intel Corporation 82852/855GM Integrated Graphics Device rev 2, Mem @ 0xb0000000/134217728, 0xf0000000/524288, I/O @ 0x0000e000/8
(II) Open ACPI successful (/var/run/acpid.socket)
(II) System resource ranges:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[5] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
(II) LoadModule: "extmod"
(II) Loading /usr/lib/xorg/modules/extensions//libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "dbe"
(II) Loading /usr/lib/xorg/modules/extensions//libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "glx"
(II) Loading /usr/lib/xorg/modules/extensions//libglx.so
(II) Module glx: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(==) AIGLX enabled
(II) Loading extension GLX
(II) LoadModule: "record"
(II) Loading /usr/lib/xorg/modules/extensions//librecord.so
(II) Module record: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.13.0
	Module class: X.Org Server Extension
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension RECORD
(II) LoadModule: "dri"
(II) Loading /usr/lib/xorg/modules/extensions//libdri.so
(II) Module dri: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension XFree86-DRI
(II) LoadModule: "dri2"
(II) Loading /usr/lib/xorg/modules/extensions//libdri2.so
(II) Module dri2: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	ABI class: X.Org Server Extension, version 2.0
(II) Loading extension DRI2
(II) Scanning /usr/share/xserver-xorg/pci directory for additional PCI ID's supported by the drivers
(II) Matched intel from file name intel.ids
(==) Matched intel for the autoconfigured driver
(==) Assigned the driver to the xf86ConfigLayout
(II) LoadModule: "intel"
(II) Loading /usr/lib/xorg/modules/drivers//intel_drv.so
(II) Module intel: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 2.6.3
	Module class: X.Org Video Driver
	ABI class: X.Org Video Driver, version 5.0
(II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
	i810-dc100, i810e, i815, i830M, 845G, 852GM/855GM, 865G, 915G,
	E7221 (i915), 915GM, 945G, 945GM, 945GME, 965G, G35, 965Q, 946GZ,
	965GM, 965GME/GLE, G33, Q35, Q33,
	Mobile Intel® GM45 Express Chipset,
	Intel Integrated Graphics Device, G45/G43, Q45/Q43, G41
(II) Primary Device is: PCI 00@00:02:0
(II) resource ranges after xf86ClaimFixedResources() call:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[5] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
(II) resource ranges after probing:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] 0	0	0x000a0000 - 0x000affff (0x10000) MS[B]
	[5] 0	0	0x000b0000 - 0x000b7fff (0x8000) MS[B]
	[6] 0	0	0x000b8000 - 0x000bffff (0x8000) MS[B]
	[7] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[8] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[9] 0	0	0x000003b0 - 0x000003bb (0xc) IS[B]
	[10] 0	0	0x000003c0 - 0x000003df (0x20) IS[B]
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/xorg/modules//libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 0.1.0
	ABI class: X.Org Video Driver, version 5.0
(II) intel(0): Creating default Display subsection in Screen section
	"Default Screen" for depth/fbbpp 24/32
(==) intel(0): Depth 24, (--) framebuffer bpp 32
(==) intel(0): RGB weight 888
(==) intel(0): Default visual is TrueColor
(II) intel(0): Integrated Graphics Chipset: Intel(R) 852GME
(--) intel(0): Chipset: "852GM/855GM"
(--) intel(0): Linear framebuffer at 0xB0000000
(--) intel(0): IO registers at addr 0xF0000000
(WW) intel(0): libpciaccess reported 0 rom size, guessing 64kB
(==) intel(0): Using EXA for acceleration
(II) intel(0): 2 display pipes available.
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Module "ddc" already built-in
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Module "i2c" already built-in
(II) intel(0): Output VGA using monitor section Configured Monitor
(II) intel(0): Output LVDS has no monitor section
(II) intel(0): I2C bus "LVDSDDC_C" initialized.
(II) intel(0): Attempting to determine panel fixed mode.
(II) intel(0): I2C device "LVDSDDC_C:E-EDID segment register" registered at address 0x60.
(II) intel(0): I2C device "LVDSDDC_C:ddc2" registered at address 0xA0.
(II) intel(0): found backlight control method /sys/class/backlight/acpi_video0
(II) intel(0): I2C bus "DVODDC_D" initialized.
(II) Loading sub module "sil164"
(II) LoadModule: "sil164"
(II) Loading /usr/lib/xorg/modules/drivers//sil164.so
(II) Module sil164: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	ABI class: X.Org Video Driver, version 5.0
(II) intel(0): I2C bus "DVOI2C_E" initialized.
(II) Loading sub module "ch7xxx"
(II) LoadModule: "ch7xxx"
(II) Loading /usr/lib/xorg/modules/drivers//ch7xxx.so
(II) Module ch7xxx: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	ABI class: X.Org Video Driver, version 5.0
(II) intel(0): I2C bus "DVOI2C_E" removed.
(II) intel(0): I2C bus "DVOI2C_E" initialized.
(II) intel(0): Detected CH7009A chipset, vendor/device ID 0x84/0x17
(II) intel(0): I2C device "DVOI2C_E:CH7xxx TMDS Controller" registered at address 0xEC.
(II) intel(0): Output TMDS has no monitor section
(II) intel(0): Resizable framebuffer: not available (1 3)
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): Output VGA disconnected
(II) intel(0): Output LVDS connected
(II) intel(0): Output TMDS disconnected
(II) intel(0): Using exact sizes for initial modes
(II) intel(0): Output LVDS using initial mode 1024x768
(II) intel(0): detected 128 kB GTT.
(II) intel(0): detected 32636 kB stolen memory.
(==) intel(0): video overlay key set to 0x101fe
(==) intel(0): Using gamma correction (1.0, 1.0, 1.0)
(==) intel(0): DPI set to (96, 96)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 1.0.0
	ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "exa"
(II) LoadModule: "exa"
(II) Loading /usr/lib/xorg/modules//libexa.so
(II) Module exa: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 2.4.0
	ABI class: X.Org Video Driver, version 5.0
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Module "ramdac" already built-in
(II) intel(0): Comparing regs from server start up to After PreInit
(WW) intel(0): Register 0x61200 (PP_STATUS) changed from 0xc0000008 to 0xd000000a
(WW) intel(0): PP_STATUS before: on, ready, sequencing idle
(WW) intel(0): PP_STATUS after: on, ready, sequencing on
(==) Depth 24 pixmap format is 32 bpp
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] 0	0	0x000a0000 - 0x000affff (0x10000) MS[B](OprD)
	[5] 0	0	0x000b0000 - 0x000b7fff (0x8000) MS[B](OprD)
	[6] 0	0	0x000b8000 - 0x000bffff (0x8000) MS[B](OprD)
	[7] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[8] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[9] 0	0	0x000003b0 - 0x000003bb (0xc) IS[B](OprU)
	[10] 0	0	0x000003c0 - 0x000003df (0x20) IS[B](OprU)
(II) intel(0): Kernel reported 104704 total, 1 used
(II) intel(0): I830CheckAvailableMemory: 418812 kB available
(WW) intel(0): DRI2 requires UXA
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: node name is /dev/dri/card0
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card1
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card2
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card3
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card4
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card5
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card6
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card7
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card8
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card9
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card10
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card11
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card12
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card13
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card14
drmOpenByBusid: drmOpenMinor returns -1
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 11, (OK)
drmGetBusid returned ''
(II) [drm] loaded kernel module for "i915" driver.
(II) [drm] DRM interface version 1.3
(II) [drm] DRM open master succeeded.
(II) intel(0): [drm] Using the DRM lock SAREA also for drawables.
(II) intel(0): [drm] framebuffer mapped by ddx driver
(II) intel(0): [drm] added 1 reserved context for kernel
(II) intel(0): X context handle = 0x1
(II) intel(0): [drm] installed DRM signal handler
(**) intel(0): Framebuffer compression enabled
(**) intel(0): Tiling enabled
(==) intel(0): VideoRam: 131072 KB
(II) intel(0): Attempting memory allocation with tiled buffers.
(WW) intel(0): xf86AllocateGARTMemory: allocation of 1536 pages failed
	(Cannot allocate memory)
(WW) intel(0): Allocation error, framebuffer compression disabled
(WW) intel(0): xf86AllocateGARTMemory: allocation of 10 pages failed
	(Cannot allocate memory)
(II) intel(0): Tiled allocation successful.
(II) intel(0): [drm] Registers = 0xf0000000
(II) intel(0): [dri] visual configs initialized
(II) intel(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) EXA(0): Offscreen pixmap area of 12582912 bytes
(II) EXA(0): Driver registered support for the following operations:
(II)         Solid
(II)         Copy
(II)         Composite (RENDER acceleration)
(==) intel(0): Backing store disabled
(==) intel(0): Silken mouse enabled
(II) intel(0): Initializing HW Cursor
(II) intel(0): [DRI] installation complete
(II) intel(0): xf86BindGARTMemory: bind key 0 at 0x06df4000 (pgoffset 28148)
(II) intel(0): xf86BindGARTMemory: bind key 1 at 0x06df5000 (pgoffset 28149)
(II) intel(0): xf86BindGARTMemory: bind key 2 at 0x06df9000 (pgoffset 28153)
(II) intel(0): xf86BindGARTMemory: bind key 3 at 0x06dfa000 (pgoffset 28154)
(II) intel(0): xf86BindGARTMemory: bind key 4 at 0x06dfe000 (pgoffset 28158)
(II) intel(0): Fixed memory allocation layout:
(II) intel(0): 0x00000000-0x00bfffff: exa offscreen (12288 kB)
(II) intel(0): 0x01fdf000:            end of stolen memory
(II) intel(0): 0x01fdf000-0x06df3fff: DRI memory manager (79956 kB)
(II) intel(0): 0x06df4000-0x06df4fff: Core cursor (4 kB, 0x000000001bd3b000 physical
)
(II) intel(0): 0x06df5000-0x06df8fff: ARGB cursor (16 kB, 0x000000001bfd4000 physical
)
(II) intel(0): 0x06df9000-0x06df9fff: Core cursor (4 kB, 0x000000001ce2e000 physical
)
(II) intel(0): 0x06dfa000-0x06dfdfff: ARGB cursor (16 kB, 0x000000001c808000 physical
)
(II) intel(0): 0x06dfe000-0x06dfefff: overlay registers (4 kB, 0x000000001ce2a000 physical
)
(II) intel(0): 0x08000000:            end of aperture
(II) intel(0): BO memory allocation layout:
(II) intel(0): 0x01fdf000:            start of memory manager
(II) intel(0): 0x02000000-0x023fffff: depth buffer (4096 kB) X tiled
(II) intel(0): 0x02400000-0x027fffff: back buffer (4096 kB) X tiled
(II) intel(0): 0x02800000-0x02bfffff: front buffer (4096 kB) X tiled
(II) intel(0): 0x06df4000:            end of memory manager
(WW) intel(0): Chosen PLL clock of 66.6 Mhz more than 2% away from desired 65.0 Mhz
(II) intel(0): Selecting standard 18 bit TMDS pixel format.
(II) intel(0): Output configuration:
(II) intel(0):   Pipe A is off
(II) intel(0):   Display plane A is now disabled and connected to pipe A.
(WW) intel(0):   Hardware claims pipe A is on while software believes it is off
(II) intel(0):   Pipe B is on
(II) intel(0):   Display plane B is now enabled and connected to pipe B.
(II) intel(0):   Output VGA is connected to pipe none
(II) intel(0):   Output LVDS is connected to pipe B
(II) intel(0):   Output TMDS is connected to pipe none
(II) intel(0): [drm] mapped front buffer at 0xb2800000, handle = 0xb2800000
(II) intel(0): [drm] mapped back buffer at 0xb2400000, handle = 0xb2400000
(II) intel(0): [drm] mapped depth buffer at 0xb2000000, handle = 0xb2000000
(II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
(II) intel(0): DPMS enabled
(==) intel(0): Intel XvMC decoder disabled
(II) intel(0): Set up overlay video
(II) intel(0): direct rendering: XF86DRI Enabled
(--) RandR disabled
(II) Initializing built-in extension Generic Event Extension
(II) Initializing built-in extension SHAPE
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension BIG-REQUESTS
(II) Initializing built-in extension SYNC
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-MISC
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) AIGLX: Screen 0 is not DRI2 capable
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: Searching for BusID pci:0000:00:02.0
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is 12, (OK)
drmOpenByBusid: drmOpenMinor returns 12
drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
(II) AIGLX: enabled GLX_SGI_make_current_read
(II) AIGLX: enabled GLX_MESA_copy_sub_buffer
(II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
(II) AIGLX: enabled GLX_texture_from_pixmap with driver support
(II) AIGLX: Loaded and initialized /usr/lib/dri/i915_dri.so
(II) GLX: Initialized DRI GL provider for screen 0
(II) intel(0): Setting screen physical size to 270 x 203
(II) config/hal: Adding input device Video Bus
(II) LoadModule: "evdev"
(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 2.1.1
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 4.0
(**) Video Bus: always reports core events
(**) Video Bus: Device: "/dev/input/event5"
(II) Video Bus: Found keys
(II) Video Bus: Configuring as keyboard
(II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Video Bus: xkb_rules: "evdev"
(**) Option "xkb_model" "pc105"
(**) Video Bus: xkb_model: "pc105"
(**) Option "xkb_layout" "it"
(**) Video Bus: xkb_layout: "it"
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event4"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) AT Translated Set 2 keyboard: xkb_rules: "evdev"
(**) Option "xkb_model" "pc105"
(**) AT Translated Set 2 keyboard: xkb_model: "pc105"
(**) Option "xkb_layout" "it"
(**) AT Translated Set 2 keyboard: xkb_layout: "it"
(II) config/hal: Adding input device Macintosh mouse button emulation
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event3"
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Configuring as mouse
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: (accel) keeping acceleration scheme 1
(**) Macintosh mouse button emulation: (accel) filter chain progression: 2.00
(**) Macintosh mouse button emulation: (accel) filter stage 0: 20.00 ms
(**) Macintosh mouse button emulation: (accel) set acceleration profile 0
(II) config/hal: Adding input device SynPS/2 Synaptics TouchPad
(II) LoadModule: "synaptics"
(II) Loading /usr/lib/xorg/modules/input//synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
	compiled for 1.6.0, module version = 0.99.3
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 4.0
(II) Synaptics touchpad driver version 0.99.3
(**) Option "Device" "/dev/input/event7"
(II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
(II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
(II) SynPS/2 Synaptics TouchPad: pressure range 0 - 255
(II) SynPS/2 Synaptics TouchPad: finger width range 0 - 0
(II) SynPS/2 Synaptics TouchPad: buttons: left right middle double triple
(--) SynPS/2 Synaptics TouchPad touchpad found
(**) SynPS/2 Synaptics TouchPad: always reports core events
(II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
(**) SynPS/2 Synaptics TouchPad: (accel) keeping acceleration scheme 1
(**) SynPS/2 Synaptics TouchPad: (accel) filter chain progression: 2.00
(**) SynPS/2 Synaptics TouchPad: (accel) filter stage 0: 20.00 ms
(**) SynPS/2 Synaptics TouchPad: (accel) set acceleration profile 0
(--) SynPS/2 Synaptics TouchPad touchpad found
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) config/hal: Adding input device HID 062a:0000
(**) HID 062a:0000: always reports core events
(**) HID 062a:0000: Device: "/dev/input/event8"
(II) HID 062a:0000: Found 3 mouse buttons
(II) HID 062a:0000: Found x and y relative axes
(II) HID 062a:0000: Configuring as mouse
(**) HID 062a:0000: YAxisMapping: buttons 4 and 5
(**) HID 062a:0000: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) XINPUT: Adding extended input device "HID 062a:0000" (type: MOUSE)
(**) HID 062a:0000: (accel) keeping acceleration scheme 1
(**) HID 062a:0000: (accel) filter chain progression: 2.00
(**) HID 062a:0000: (accel) filter stage 0: 20.00 ms
(**) HID 062a:0000: (accel) set acceleration profile 0
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.
(II) intel(0): I2C bus "CRTDDC_A" initialized.
(II) intel(0): I2C bus "CRTDDC_A" removed.

[rds4ever]

(II) Cannot locate a core pointer device.
(II) Cannot locate a core keyboard device.
(II) The server relies on HAL to provide the list of input devices.
If no devices become available, reconfigure HAL or disable AllowEmptyInput.

Il syslog sembra pulito, mentre nell'xorg.log quelle righe che ho scritto sopra mi sembrano quantomeno sospette.

Faccio qualche ricerca e ti dico,

Ciao
Riccardo

[nicotto]

Grazie 1000 per l'interessamento

[rds4ever]

Ciao,

le cose che ti ho segnalato prima, dalle ricerche che ho fatto, non sembrano essere errori preoccupanti. L'unica cosa "strana" che ho trovato e' che in alcuni siti suggeriscono di provare il portatile senza batteria ma solo con l'alimentazione.
Ti sembrerà assurdo, ma questo e' quello che ho trovato finora.

Adesso devo andare, quando torno provo a cercare meglio.

Ciao,

Riccardo

[nicotto]

Grazie comunque di tutto (good)

[nicotto]

Il problema si è risolto da solo quando ubuntu ha fatto il check periodico dell'hd all'avvio,ma dopo una settimana il problema si è ripresentato. Non è possibile fare questa procedura manualmente?

[nativis]

Il problema si è risolto da solo quando ubuntu ha fatto il check periodico dell'hd all'avvio,ma dopo una settimana il problema si è ripresentato. Non è possibile fare questa procedura manualmente?

Questo sintomo non lo avevo mai letto. Comunque sarebbe meglio sapere che hardware usi (scheda grafica, ecc) e quali drivers. Chi legge potrebbe regolarsi meglio.
ceu

[nicotto]

Beh,ho un notebook packard bell della serie easynote M (non ricordo il modello preciso) abbastanza vecchio,del 2002-3 che monta un intel pentium 4 da 2.60 ghz,con 512 mb di ram (32 condivisi con la scheda grafica),scheda video inclusa nel chipset intel da 32 mb dedicati + i 32 condivisi con la ram. Più di questo non ricordo.

P.S. Mica esiste un'utility che mi consente di visualizzare dettagliatamente le specifiche del pc (tipo Everest per win,per intenderci)?

[nativis]

Beh,ho un notebook packard bell della serie easynote M (non ricordo il modello preciso) abbastanza vecchio,del 2002-3 che monta un intel pentium 4 da 2.60 ghz,con 512 mb di ram (32 condivisi con la scheda grafica),scheda video inclusa nel chipset intel da 32 mb dedicati + i 32 condivisi con la ram. Più di questo non ricordo.

P.S. Mica esiste un'utility che mi consente di visualizzare dettagliatamente le specifiche del pc (tipo Everest per win,per intenderci)?

Per ottenere informazioni dettagliate puoi spesso usare il comando ls (list) + l'argomento che cerchi. Per esempio l'hardware:

Codice: Seleziona tutto

sudo lshw

Su periferiche usb invece:

Codice: Seleziona tutto

lsusb

Nelle guide della comunità ne trovi molti altri.
Se vuoi un programma con interfaccia puoi usare sysinfo e simili. Molti, come  hwdata, discover, hwinfo, ecc. non li conosco. Ce ne sono diversi nei repositories. Non so quanto siano approfonditi quindi scegli quello che ti soddisfa di più. basta aprire synaptic e scrivere "hardware" o cose simili.

Riguardo al tuo problema, non avendo io un notebook e men che meno schede integrate, prendi quello che segue con le molle.
Mi è capitato di leggere in passato di problemi al monitor nei notebook. A volte era il software ma altre volte era l'hardware. Il tuo risale al 2002 circa, quindi c'è la possibilità che tu debba pulire l'attacco del cavetto monitor al notebook (almeno così ho letto riguardo alcuni problemi video).
Per il resto, si vedrà quando avrai il modello esatto della scheda.

ciau 

Edit. forse già lo sai ma il forum ha una sezione dedicata solo ai notebook e nella documentazione (guide della comunità) ci sono guide specifiche.  

[nicotto]

Che sia un problema del monitor lo escludo,perchè si verifica solo all'avvio e mai in altri momenti.
Ciò che dice sysinfo riguardo la scheda video è: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)

[nativis]

Che sia un problema del monitor lo escludo,perchè si verifica solo all'avvio e mai in altri momenti.
Ciò che dice sysinfo riguardo la scheda video è: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)

Qui:
http://wiki.ubuntu-it.org/Hardware/Video/Intel
Risulta come supportata.

Qui c'è la guida alla risoluzione di alcuni problemi, ma non parla del tuo : (
http://wiki.ubuntu-it.org/Hardware/Video/Intel/Jaunty

Purtroppo non so aggiungere altro. Consiglierei però di inserire la tua descrizione del problema e il tuo hardware nella sottosezione Ubuntu su Notebook, dove il tuo messaggio potrà essere visto da chi li usa abitualmente.
qui: http://forum.ubuntu-it.org/viewforum.php?f=47

Spero tu risolva

Edit: I siti dei produttori hanno anche una sezione, dedicata ai vari componenti, detta spesso "problemi noti" e simili. Eventualmente qualche info potrebbe arrivare da lì.

[nicotto]

beh,in effetti,un'altro problemino ci sarebbe oltre a quello dell'avvio. Il mio pc risulta sempre non avere il supporto python-opengl e non riesco,ad esempio, a giocare alla modalità 3D degli scacchi e compiz non funziona in modo ottimale,molto peggio di come funzionava a parità di hardware,con intrepid. installando il pacchetto python-opengl pensavo che il problema fosse risolto(come è successo anche con python-gtkgle1) ma continua a darmi problemi.

[nativis]

beh,in effetti,un'altro problemino ci sarebbe oltre a quello dell'avvio. Il mio pc risulta sempre non avere il supporto python-opengl e non riesco,ad esempio, a giocare alla modalità 3D degli scacchi e compiz non funziona in modo ottimale,molto peggio di come funzionava a parità di hardware,con intrepid. installando il pacchetto python-opengl pensavo che il problema fosse risolto(come è successo anche con python-gtkgle1) ma continua a darmi problemi.

Mi è sorto un dubbio.
Quando cercavo la tua scheda fra quelle supportate per l'accellerazione 3D, ho inserito solo 855. Ma ora mi accorgo che GM viene espressamente specificato nella serie i915. E' quindi possibile che ci sia una differenza tra il supporto dichiarato a i852/855 e la tua 855GM. Sui chip intel ne so poco perché uso ATI : (

[nicotto]

Si,ma sia con intrepid sia con hardy l'accelerazione grafica andava benino,ovviamente nei limiti del mio hardware abbastanza limitato (64mb di memoria video sono un pò pochini,ma 32mb di condivisione sono il massimo impostabile). Riuscivo comunque ad attivare senza troppi problemi molti degli effetti di compiz,anche quelli più pesanti. Ora,con pochi effetti attivati,va abbastanza lento (è comunque usabile,ma non regge il paragone con quando usavo hardy). E a volte sono costretto tramite la Compiz-Fusion Icon a ricaricare il window manager perchè spuntano strani bug che mi fanno apparire una specie di cornice attorno alle finestre ed alle barre ed altri malfunzionamenti. Questi problemi non si presentano se uso metacity e non compiz,ma senza trasparenze,ombre ed effettini vari non riesco a stare  >:(

EDIT: Altra cosa che ho notato,quando ad esempio scorro una pagina web o gli elementi di una cartella,l'avanzamento va visibilmente a scatti,non è fluido.

[nativis]

Si,ma sia con intrepid sia con hardy l'accelerazione grafica andava benino,ovviamente nei limiti del mio hardware abbastanza limitato (64mb di memoria video sono un pò pochini,ma 32mb di condivisione sono il massimo impostabile). Riuscivo comunque ad attivare senza troppi problemi molti degli effetti di compiz,anche quelli più pesanti. Ora,con pochi effetti attivati,va abbastanza lento (è comunque usabile,ma non regge il paragone con quando usavo hardy). E a volte sono costretto tramite la Compiz-Fusion Icon a ricaricare il window manager perchè spuntano strani bug che mi fanno apparire una specie di cornice attorno alle finestre ed alle barre ed altri malfunzionamenti. Questi problemi non si presentano se uso metacity e non compiz,ma senza trasparenze,ombre ed effettini vari non riesco a stare  >:(

Ultimamente non si possono fare troppi paragoni tra una versione di Ubuntu e l'altra perché ci sono molte differenze nel gestore delle periferiche X Window (X11, xorg e altri nomi).
Per esempio molte schede ATI non possono più usare i drivers ATI su Jaunty (tanto per farti l'esempio più radicale).

Ho appena trovato che, per il 3D e la fluidità di video e applicazioni, il problema è già stato segnalato e ci sarebbe anche una procedura che comprende la 855GM:

3D performance has regressed compared to the Intrepid release, possibly due to major code changes that have resulted from the introduction to the new acceleration and memory management code (UXA, GEM, DRI2). Due to these changes, there seems to be some regressions in the “legacy” DRI acceleration.

Viene da questa discussione: http://forum.ubuntu-it.org/viewtopic.php?t=282419
che è dichiarata come risolta (non fare che non leggi tutto il post : ).

il link alla procedura è questo: http://www.ubuntugeek.com/intel-graphic ... users.html

Come vedi ci vuole un po' di confidenza con Ubuntu per affrontarla.
[edit] risulta espressamente citata la tua Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)[/edit]

Però dice anche che ci sono diverse discussioni sull'argomento e che se cerchi incrociando parole chiave come intel, 855GM, jaunty, risolto, eccetera, potrebbe saltar fuori altro.