l3on ha scritto:
Hai preso in considerazione il fatto che l'HD potrebbe essersi rovinato?
Installa il pacchetto smartmontools e poi esegui questo comando:
sostituendo a sda il nome del tuo HD.
Posta il risultato.
PS: per ogni problema riscontrato crea una nuova discussione! Ciao..
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is
http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: ST9320320AS
Serial Number: 5SX5ZP1B
Firmware Version: HP07
User Capacity: 320,072,933,376 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Sat May 15 09:58:16 2010 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 712) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 117) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 097 090 006 Pre-fail Always - 176818380
3 Spin_Up_Time 0x0002 100 099 000 Old_age Always - 0
4 Start_Stop_Count 0x0033 100 100 020 Pre-fail Always - 656
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always - 15860133
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 917
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0033 100 100 020 Pre-fail Always - 638
184 Unknown_Attribute 0x0033 100 100 097 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 245
188 Unknown_Attribute 0x0032 100 099 000 Old_age Always - 4295032833
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 069 049 045 Old_age Always - 31 (Lifetime Min/Max 24/31)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 56
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1676
194 Temperature_Celsius 0x0022 031 051 000 Old_age Always - 31 (0 14 0 0)
195 Hardware_ECC_Recovered 0x001a 048 045 000 Old_age Always - 176818380
196 Reallocated_Event_Count 0x0033 100 100 036 Pre-fail Always - 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 4
254 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 258 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 258 occurred at disk power-on lifetime: 916 hours (38 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 eb a7 1a 0e
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ea a7 1a 4e 00 02:26:27.232 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 02:26:27.232 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 a0 00 02:26:27.230 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 02:26:27.230 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 02:26:27.230 SET FEATURES [Reserved for Serial ATA]
Error 257 occurred at disk power-on lifetime: 916 hours (38 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 eb a7 1a 0e
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ea a7 1a 4e 00 02:26:24.789 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 02:26:24.789 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 a0 00 02:26:24.787 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 02:26:24.787 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 02:26:24.787 SET FEATURES [Reserved for Serial ATA]
Error 256 occurred at disk power-on lifetime: 916 hours (38 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 eb a7 1a 0e
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ea a7 1a 4e 00 02:26:22.391 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 02:26:22.390 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 a0 00 02:26:22.389 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 02:26:22.388 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 02:26:22.388 SET FEATURES [Reserved for Serial ATA]
Error 255 occurred at disk power-on lifetime: 916 hours (38 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 eb a7 1a 0e
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ea a7 1a 4e 00 02:26:19.981 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 02:26:19.980 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 a0 00 02:26:19.979 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 02:26:19.979 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 02:26:19.978 SET FEATURES [Reserved for Serial ATA]
Error 254 occurred at disk power-on lifetime: 916 hours (38 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 eb a7 1a 0e
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ea a7 1a 4e 00 02:26:17.582 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 02:26:17.582 SET FEATURES [Reserved for Serial ATA]
ec 00 00 00 00 00 a0 00 02:26:17.580 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 02:26:17.580 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 00 02:26:17.580 SET FEATURES [Reserved for Serial ATA]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 910 -
# 2 Short offline Completed without error 00% 628 -
# 3 Short offline Completed without error 00% 628 -
# 4 Short offline Completed without error 00% 628 -
# 5 Short offline Completed without error 00% 628 -
# 6 Short offline Completed without error 00% 428 -
# 7 Short offline Completed without error 00% 428 -
# 8 Short offline Completed without error 00% 428 -
# 9 Short offline Completed without error 00% 428 -
#10 Short offline Completed without error 00% 427 -
#11 Short offline Completed without error 00% 427 -
#12 Short offline Completed without error 00% 427 -
#13 Short offline Completed without error 00% 427 -
#14 Short offline Completed without error 00% 427 -
#15 Short offline Completed without error 00% 427 -
#16 Short offline Completed without error 00% 427 -
#17 Short offline Completed without error 00% 426 -
#18 Short offline Completed without error 00% 426 -
#19 Short offline Completed without error 00% 426 -
#20 Short offline Completed without error 00% 155 -
#21 Short offline Completed without error 00% 3 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.