1. ho installato ubunatu versione 6.10 (non per i processori a 64 bit) scaricata direttamente dal sito senza alcuna modifica aggiuntiva al kernel, e con la pcmcia inserita nell'apposito slot.
2. Terminata l'installazione sono andato da terminale e ho lanciato il comando serial_cs
.
3. Ho fatto un dmesg e come scritto in una guida ho copiato il valore vendor e product, che nel mio caso ho digitato questo comando (loggato root) sudo modprobe usbserial vendor=0x0000 product=0x0000 (da premettere che nn mi convinge tanto questo comando... perchè mi sembra strano che i valori siano uguali a zero.. ma cmq in un post su questo sito c'era di eseguire in questa maniera e così ho fatto.
4. Ho configurato il tutto sembre da terminale lanciando un sudo pppconfig , ho creato una nuova connessione, aggiunto i relativi dns primario e secondario, aggiunto anche la stringa di inizializzazione del modem, inserito il numero da comporre (*99***1#) ecc...
Fatto tutto se lascio come porta /dev/ttyUSB0 mi da un errore se invece nella connessione inserisco /dev/ttyS0 e poi sempre da terminale dò il pon nome_scelto_della_connessione_creata nn mi dice nulla e nemmeno mi segnala errori.
Adesso la mia domanda è visto che lanciando il comando sudo cardtcl eject (comando per togliere in modo corretto la pc connect card) mi da errore dicendomi che è in esecuzione quando invece nn si connette assolutissimamente... il sistema mi ha riconosciuto la pc card? ha installato i driver? mi dareste i vari parametri corretti per il funzionamento della connessione da parte della TIM ? grazie ragazazzi aiutatemi voi please...
vi posto alcuni log eseguiti da terminale con la pcmcia inserita nel suo apposito slot.
Facendo un lsusb
Codice: Seleziona tutto
carmelo@AMD64:~$ lsusb
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 001: ID 0000:0000
Codice: Seleziona tutto
carmelo@AMD64:~$ dmesg|grep usb
[17179577.972000] usbcore: registered new driver usbfs
[17179577.972000] usbcore: registered new driver hub
[17179578.036000] usb usb1: configuration #1 chosen from 1 choice
[17179578.200000] usb usb2: configuration #1 chosen from 1 choice
[17179578.304000] usb usb3: configuration #1 chosen from 1 choice
[17179900.656000] usbcore: registered new driver usbserial
[17179900.656000] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
[17179900.656000] usbcore: registered new driver usbserial_generic
[17179900.656000] drivers/usb/serial/usb-serial.c: USB Serial Driver core
carmelo@AMD64:~$
Codice: Seleziona tutto
carmelo@AMD64:~$ dmesg
[17179569.184000] Linux version 2.6.17-10-generic (root@vernadsky) (gcc version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #2 SMP Fri Oct 13 18:45:35 UTC 2006 (Ubuntu 2.6.17-10.33-generic)
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[17179569.184000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[17179569.184000] BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
[17179569.184000] BIOS-e820: 0000000000100000 - 000000001fef0000 (usable)
[17179569.184000] BIOS-e820: 000000001fef0000 - 000000001feff000 (ACPI data)
[17179569.184000] BIOS-e820: 000000001feff000 - 000000001ff00000 (ACPI NVS)
[17179569.184000] BIOS-e820: 000000001ff00000 - 0000000020000000 (reserved)
[17179569.184000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[17179569.184000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[17179569.184000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 510MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000f7e20
[17179569.184000] On node 0 totalpages: 130800
[17179569.184000] DMA zone: 4096 pages, LIFO batch:0
[17179569.184000] Normal zone: 126704 pages, LIFO batch:31
[17179569.184000] DMI present.
[17179569.184000] ACPI: RSDP (v000 PTLTD ) @ 0x000f7df0
[17179569.184000] ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x1fef9521
[17179569.184000] ACPI: FADT (v001 HP Piranha 0x06040000 ATI 0x000f4240) @ 0x1fefee27
[17179569.184000] ACPI: MCFG (v001 ATI Piranha 0x06040000 LOHR 0x0000005f) @ 0x1fefee9b
[17179569.184000] ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x1fefeed7
[17179569.184000] ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x1fefefa6
[17179569.184000] ACPI: DSDT (v001 HP 3085 0x06040000 MSFT 0x0100000e) @ 0x00000000
[17179569.184000] ATI board detected. Disabling timer routing over 8254.
[17179569.184000] ACPI: PM-Timer IO Port: 0x8008
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 15:15 APIC version 16
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[17179569.184000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level)
[17179569.184000] ACPI: IRQ0 used by override.
[17179569.184000] ACPI: IRQ2 used by override.
[17179569.184000] Enabling APIC mode: Flat. Using 1 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hda1 ro quiet splash locale=it_IT
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] Enabling fast FPU save and restore... done.
[17179569.184000] Enabling unmasked SIMD FPU exception support... done.
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[17179569.184000] Detected 997.285 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179571.064000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179571.064000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179571.080000] Memory: 509032k/523200k available (1910k kernel code, 13528k reserved, 1070k data, 308k init, 0k highmem)
[17179571.080000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179571.160000] Calibrating delay using timer specific routine.. 1997.68 BogoMIPS (lpj=3995367)
[17179571.160000] Security Framework v1.0.0 initialized
[17179571.160000] SELinux: Disabled at boot.
[17179571.160000] Mount-cache hash table entries: 512
[17179571.160000] CPU: After generic identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000
[17179571.160000] CPU: After vendor identify, caps: 078bfbff e1d3fbff 00000000 00000000 00000000 00000000 00000000
[17179571.160000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[17179571.160000] CPU: L2 Cache: 512K (64 bytes/line)
[17179571.160000] CPU: After all inits, caps: 078bfbff e1d3fbff 00000000 00000410 00000000 00000000 00000000
[17179571.160000] Checking 'hlt' instruction... OK.
[17179571.176000] SMP alternatives: switching to UP code
[17179571.176000] Freeing SMP alternatives: 16k freed
[17179571.176000] checking if image is initramfs... it is
[17179572.048000] Freeing initrd memory: 5254k freed
[17179572.048000] ACPI: Core revision 20060707
[17179572.048000] ACPI: Looking for DSDT ... not found!
[17179572.688000] CPU0: AMD Athlon(tm) 64 Processor 3200+ stepping 00
[17179572.688000] Total of 1 processors activated (1997.68 BogoMIPS).
[17179572.688000] ENABLING IO-APIC IRQs
[17179572.688000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[17179572.688000] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[17179572.688000] ...trying to set up timer (IRQ0) through the 8259A ... failed.
[17179572.688000] ...trying to set up timer as Virtual Wire IRQ... works.
[17179572.872000] Brought up 1 CPUs
[17179572.872000] migration_cost=0
[17179572.872000] NET: Registered protocol family 16
[17179572.872000] EISA bus registered
[17179572.872000] ACPI: bus type pci registered
[17179572.872000] PCI: Using MMCONFIG
[17179572.872000] PCI: No mmconfig possible on 0:18
[17179572.900000] Setting up standard PCI resources
[17179572.904000] ACPI: Interpreter enabled
[17179572.904000] ACPI: Using IOAPIC for interrupt routing
[17179572.904000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179572.904000] PCI: Probing PCI hardware (bus 00)
[17179572.976000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
[17179572.976000] Boot video device is 0000:01:05.0
[17179573.004000] PCI: Transparent bridge - 0000:00:14.4
[17179573.004000] PCI: Bus #04 (-#07) is hidden behind transparent bridge #03 (-#04) (try 'pci=assign-busses')
[17179573.004000] Please report the result to linux-kernel to fix this permanently
[17179573.004000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179573.008000] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
[17179573.008000] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
[17179573.008000] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
[17179573.008000] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
[17179573.008000] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
[17179573.008000] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
[17179573.008000] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
[17179573.012000] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
[17179573.012000] ACPI: Embedded Controller [EC0] (gpe 26) interrupt mode.
[17179573.052000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT]
[17179573.076000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[17179573.076000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[17179573.076000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179573.076000] pnp: PnP ACPI init
[17179573.128000] pnp: PnP ACPI: found 10 devices
[17179573.128000] PnPBIOS: Disabled by ACPI PNP
[17179573.128000] PCI: Using ACPI for IRQ routing
[17179573.128000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[17179573.128000] PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0
[17179573.128000] PCI: Cannot allocate resource region 8 of bridge 0000:00:04.0
[17179573.128000] pnp: 00:08: ioport range 0x1080-0x1080 has been reserved
[17179573.128000] pnp: 00:08: ioport range 0x220-0x22f has been reserved
[17179573.128000] pnp: 00:08: ioport range 0x40b-0x40b has been reserved
[17179573.128000] pnp: 00:08: ioport range 0x4d0-0x4d1 has been reserved
[17179573.128000] PCI: Bridge: 0000:00:01.0
[17179573.128000] IO window: 9000-9fff
[17179573.128000] MEM window: b0100000-b01fffff
[17179573.128000] PREFETCH window: c0000000-cfffffff
[17179573.128000] PCI: Bridge: 0000:00:04.0
[17179573.128000] IO window: disabled.
[17179573.128000] MEM window: disabled.
[17179573.128000] PREFETCH window: disabled.
[17179573.128000] PCI: Bus 4, cardbus bridge: 0000:03:04.0
[17179573.128000] IO window: 0000a400-0000a4ff
[17179573.128000] IO window: 0000a800-0000a8ff
[17179573.128000] PREFETCH window: 30000000-31ffffff
[17179573.128000] MEM window: 32000000-33ffffff
[17179573.128000] PCI: Bridge: 0000:00:14.4
[17179573.128000] IO window: a000-afff
[17179573.128000] MEM window: b0200000-b02fffff
[17179573.128000] PREFETCH window: 30000000-31ffffff
[17179573.128000] PCI: Setting latency timer of device 0000:00:04.0 to 64
[17179573.128000] ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 20 (level, low) -> IRQ 177
[17179573.128000] NET: Registered protocol family 2
[17179573.164000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[17179573.164000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[17179573.164000] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[17179573.164000] TCP: Hash tables configured (established 16384 bind 8192)
[17179573.164000] TCP reno registered
[17179573.164000] audit: initializing netlink socket (disabled)
[17179573.164000] audit(1166478326.164:1): initialized
[17179573.164000] VFS: Disk quotas dquot_6.5.1
[17179573.164000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179573.164000] Initializing Cryptographic API
[17179573.164000] io scheduler noop registered
[17179573.164000] io scheduler anticipatory registered
[17179573.164000] io scheduler deadline registered
[17179573.164000] io scheduler cfq registered (default)
[17179573.164000] PCI: Setting latency timer of device 0000:00:04.0 to 64
[17179573.164000] pcie_portdrv_probe->Dev[5a36:1002] has invalid IRQ. Check vendor BIOS
[17179573.164000] assign_interrupt_mode Found MSI capability
[17179573.164000] Allocate Port Service[0000:00:04.0:pcie00]
[17179573.164000] Allocate Port Service[0000:00:04.0:pcie01]
[17179573.164000] isapnp: Scanning for PnP cards...
[17179573.520000] isapnp: No Plug & Play device found
[17179573.548000] Real Time Clock Driver v1.12ac
[17179573.548000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[17179573.552000] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 201
[17179573.552000] ACPI: PCI interrupt for device 0000:00:14.6 disabled
[17179573.552000] mice: PS/2 mouse device common for all mice
[17179573.552000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179573.552000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179573.552000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179573.552000] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[17179573.560000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179573.560000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179573.560000] EISA: Probing bus 0 at eisa.0
[17179573.560000] Cannot allocate resource for EISA slot 1
[17179573.560000] Cannot allocate resource for EISA slot 8
[17179573.560000] EISA: Detected 0 cards.
[17179573.560000] TCP bic registered
[17179573.560000] NET: Registered protocol family 1
[17179573.560000] NET: Registered protocol family 8
[17179573.560000] NET: Registered protocol family 20
[17179573.560000] Using IPI No-Shortcut mode
[17179573.560000] ACPI: (supports S0 S3 S4 S5)
[17179573.560000] Freeing unused kernel memory: 308k freed
[17179573.564000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179574.708000] Capability LSM initialized
[17179574.772000] ACPI: Processor [CPU0] (supports 8 throttling states)
[17179574.780000] ACPI Exception (acpi_thermal-0417): AE_NOT_FOUND, Invalid active threshold [0] [20060707]
[17179574.780000] ACPI: Thermal Zone [THRM] (20 C)
[17179575.300000] ATIIXP: IDE controller at PCI slot 0000:00:14.1
[17179575.300000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 209
[17179575.300000] ATIIXP: chipset revision 0
[17179575.300000] ATIIXP: not 100% native mode: will probe irqs later
[17179575.300000] ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hda:DMA, hdb:pio
[17179575.300000] ide1: BM-DMA at 0x8418-0x841f, BIOS settings: hdc:DMA, hdd:pio
[17179575.300000] Probing IDE interface ide0...
[17179575.588000] hda: TOSHIBA MK8025GAS, ATA DISK drive
[17179576.260000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179576.308000] Probing IDE interface ide1...
[17179577.044000] hdc: HL-DT-ST DVD-RW GWA-4082N, ATAPI CD/DVD-ROM drive
[17179577.380000] ide1 at 0x170-0x177,0x376 on irq 15
[17179577.392000] hda: max request size: 128KiB
[17179577.404000] hda: 156301488 sectors (80026 MB), CHS=65535/16/63, UDMA(100)
[17179577.404000] hda: cache flushes supported
[17179577.404000] hda: hda1 hda2 < hda5 >
[17179577.512000] hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, DMA
[17179577.512000] Uniform CD-ROM driver Revision: 3.20
[17179577.972000] usbcore: registered new driver usbfs
[17179577.972000] usbcore: registered new driver hub
[17179577.972000] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
[17179577.972000] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 217
[17179577.972000] ohci_hcd 0000:00:13.0: OHCI Host Controller
[17179577.972000] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[17179577.972000] ohci_hcd 0000:00:13.0: irq 217, io mem 0xb0000000
[17179577.992000] ieee1394: Initialized config rom entry `ip1394'
[17179578.036000] usb usb1: configuration #1 chosen from 1 choice
[17179578.036000] hub 1-0:1.0: USB hub found
[17179578.036000] hub 1-0:1.0: 4 ports detected
[17179578.140000] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 217
[17179578.140000] ohci_hcd 0000:00:13.1: OHCI Host Controller
[17179578.140000] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
[17179578.140000] ohci_hcd 0000:00:13.1: irq 217, io mem 0xb0001000
[17179578.200000] usb usb2: configuration #1 chosen from 1 choice
[17179578.200000] hub 2-0:1.0: USB hub found
[17179578.200000] hub 2-0:1.0: 4 ports detected
[17179578.304000] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 217
[17179578.304000] ehci_hcd 0000:00:13.2: EHCI Host Controller
[17179578.304000] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3
[17179578.304000] ehci_hcd 0000:00:13.2: irq 217, io mem 0xb0002000
[17179578.304000] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[17179578.304000] usb usb3: configuration #1 chosen from 1 choice
[17179578.304000] hub 3-0:1.0: USB hub found
[17179578.304000] hub 3-0:1.0: 8 ports detected
[17179578.408000] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 20 (level, low) -> IRQ 177
[17179578.456000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[177] MMIO=[b0208000-b02087ff] Max Packet=[2048] IR/IT contexts=[4/8]
[17179578.588000] Attempting manual resume
[17179578.652000] kjournald starting. Commit interval 5 seconds
[17179578.652000] EXT3-fs: mounted filesystem with ordered data mode.
[17179579.728000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[593f02006f254079]
[17179590.836000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179590.840000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179591.316000] ieee80211_crypt: registered algorithm 'NULL'
[17179591.320000] ieee80211: 802.11 data/management/control stack, git-1.1.13
[17179591.320000] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[17179591.332000] ACPI: PCI Interrupt 0000:03:04.0[A] -> GSI 20 (level, low) -> IRQ 177
[17179591.332000] Yenta: CardBus bridge found at 0000:03:04.0 [103c:3085]
[17179591.332000] Yenta: Enabling burst memory read transactions
[17179591.332000] Yenta: Using INTVAL to route CSC interrupts to PCI
[17179591.332000] Yenta: Routing CardBus interrupts to ISA
[17179591.332000] Yenta TI: socket 0000:03:04.0, mfunc 0x00aa1b22, devctl 0x64
[17179591.436000] input: PC Speaker as /class/input/input1
[17179591.612000] Linux agpgart interface v0.101 (c) Dave Jones
[17179591.624000] Yenta: ISA IRQ mask 0x0ef8, PCI irq 177
[17179591.624000] Socket status: 30000820
[17179591.624000] Yenta: Raising subordinate bus# of parent bus (#03) from #04 to #07
[17179591.624000] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
[17179591.624000] cs: IO port probe 0xa000-0xafff: clean.
[17179591.624000] pcmcia: parent PCI bridge Memory window: 0xb0200000 - 0xb02fffff
[17179591.624000] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x31ffffff
[17179591.624000] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 201
[17179591.736000] MC'97 0 converters and GPIO not ready (0x1)
[17179591.736000] ACPI: PCI Interrupt 0000:03:04.3[B] -> GSI 21 (level, low) -> IRQ 169
[17179591.744000] bcm43xx driver
[17179591.744000] ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 21 (level, low) -> IRQ 169
[17179591.756000] sdhci: Secure Digital Host Controller Interface driver, 0.12
[17179591.756000] sdhci: Copyright(c) Pierre Ossman
[17179591.756000] sdhci: SDHCI controller found at 0000:03:04.4 [104c:8034] (rev 0)
[17179591.756000] ACPI: PCI Interrupt 0000:03:04.4[D] -> GSI 23 (level, low) -> IRQ 225
[17179591.756000] mmc0: SDHCI at 0xb020a000 irq 225 DMA
[17179591.756000] mmc1: SDHCI at 0xb0208c00 irq 225 DMA
[17179591.756000] mmc2: SDHCI at 0xb0208800 irq 225 DMA
[17179591.804000] ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 201
[17179591.852000] 8139too Fast Ethernet driver 0.9.27
[17179591.852000] ACPI: PCI Interrupt 0000:03:06.0[A] -> GSI 22 (level, low) -> IRQ 233
[17179591.852000] eth1: RealTek RTL8139 at 0xe09dc400, 00:0f:b0:77:35:11, IRQ 233
[17179591.852000] eth1: Identified 8139 chip type 'RTL-8100B/8139D'
[17179591.864000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[17179592.084000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x23a0b1, caps: 0xa04713/0x200000
[17179592.116000] input: SynPS/2 Synaptics TouchPad as /class/input/input2
[17179592.480000] ts: Compaq touchscreen protocol output
[17179592.528000] pccard: CardBus card inserted into slot 0
[17179592.716000] cs: IO port probe 0x100-0x3af: clean.
[17179592.720000] cs: IO port probe 0x3e0-0x4ff: clean.
[17179592.720000] cs: IO port probe 0x820-0x8ff: excluding 0x878-0x87f
[17179592.720000] cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf
[17179592.720000] cs: IO port probe 0xa00-0xaff: clean.
[17179593.004000] lp: driver loaded but no devices found
[17179593.080000] SCSI subsystem initialized
[17179593.096000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[17179593.096000] ieee1394: sbp2: Try serialize_io=0 for better performance
[17179593.136000] Adding 1510068k swap on /dev/disk/by-uuid/f991ff21-87a7-4635-bfc2-9edce7ad08ca. Priority:-1 extents:1 across:1510068k
[17179593.228000] EXT3 FS on hda1, internal journal
[17179594.864000] ACPI: AC Adapter [ACAD] (off-line)
[17179595.080000] ACPI: Battery Slot [BAT1] (battery present)
[17179595.108000] ACPI: Power Button (FF) [PWRF]
[17179595.108000] ACPI: Lid Switch [LID]
[17179595.108000] ACPI: Power Button (CM) [PWRB]
[17179595.276000] ibm_acpi: ec object not found
[17179595.316000] pcc_acpi: loading...
[17179595.456000] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[17179595.776000] powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.60.2)
[17179595.796000] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x2 (1500 mV)
[17179595.796000] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x6 (1400 mV)
[17179595.796000] powernow-k8: 2 : fid 0x2 (1000 MHz), vid 0x10 (1150 mV)
[17179595.796000] cpu_init done, current fid 0x2, vid 0x12
[17179595.796000] powernow-k8: ignoring illegal change in lo freq table-2 to 0x2
[17179595.796000] powernow-k8: transition frequency failed
[17179595.796000] powernow-k8: ignoring illegal change in lo freq table-2 to 0x2
[17179595.796000] powernow-k8: transition frequency failed
[17179599.216000] apm: BIOS not found.
[17179605.344000] Bluetooth: Core ver 2.8
[17179605.344000] NET: Registered protocol family 31
[17179605.344000] Bluetooth: HCI device and connection manager initialized
[17179605.344000] Bluetooth: HCI socket layer initialized
[17179605.404000] Bluetooth: L2CAP ver 2.8
[17179605.404000] Bluetooth: L2CAP socket layer initialized
[17179605.408000] Bluetooth: RFCOMM socket layer initialized
[17179605.408000] Bluetooth: RFCOMM TTY layer initialized
[17179605.408000] Bluetooth: RFCOMM ver 1.7
[17179617.372000] NET: Registered protocol family 10
[17179617.372000] lo: Disabled Privacy Extensions
[17179617.372000] IPv6 over IPv4 tunneling driver
[17179900.656000] usbcore: registered new driver usbserial
[17179900.656000] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
[17179900.656000] usbcore: registered new driver usbserial_generic
[17179900.656000] drivers/usb/serial/usb-serial.c: USB Serial Driver core
carmelo@AMD64:~$
Codice: Seleziona tutto
carmelo@AMD64:~$ dmesg|tail
[17179605.408000] Bluetooth: RFCOMM TTY layer initialized
[17179605.408000] Bluetooth: RFCOMM ver 1.7
[17179617.372000] NET: Registered protocol family 10
[17179617.372000] lo: Disabled Privacy Extensions
[17179617.372000] IPv6 over IPv4 tunneling driver
[17179900.656000] usbcore: registered new driver usbserial
[17179900.656000] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
[17179900.656000] usbcore: registered new driver usbserial_generic
[17179900.656000] drivers/usb/serial/usb-serial.c: USB Serial Driver core
[17181056.864000] APIC error on CPU0: 00(40)
carmelo@AMD64:~$
Codice: Seleziona tutto
carmelo@AMD64:~$ ls /dev/tty*
/dev/tty /dev/tty30 /dev/tty53 /dev/ttyaa /dev/ttyc3 /dev/ttydc /dev/ttyp5 /dev/ttyqe /dev/ttyS3 /dev/ttytc /dev/ttyv5 /dev/ttywe /dev/ttyy7
/dev/tty0 /dev/tty31 /dev/tty54 /dev/ttyab /dev/ttyc4 /dev/ttydd /dev/ttyp6 /dev/ttyqf /dev/ttys4 /dev/ttytd /dev/ttyv6 /dev/ttywf /dev/ttyy8
/dev/tty1 /dev/tty32 /dev/tty55 /dev/ttyac /dev/ttyc5 /dev/ttyde /dev/ttyp7 /dev/ttyr0 /dev/ttys5 /dev/ttyte /dev/ttyv7 /dev/ttyx0 /dev/ttyy9
/dev/tty10 /dev/tty33 /dev/tty56 /dev/ttyad /dev/ttyc6 /dev/ttydf /dev/ttyp8 /dev/ttyr1 /dev/ttys6 /dev/ttytf /dev/ttyv8 /dev/ttyx1 /dev/ttyya
/dev/tty11 /dev/tty34 /dev/tty57 /dev/ttyae /dev/ttyc7 /dev/ttye0 /dev/ttyp9 /dev/ttyr2 /dev/ttys7 /dev/ttyu0 /dev/ttyv9 /dev/ttyx2 /dev/ttyyb
/dev/tty12 /dev/tty35 /dev/tty58 /dev/ttyaf /dev/ttyc8 /dev/ttye1 /dev/ttypa /dev/ttyr3 /dev/ttys8 /dev/ttyu1 /dev/ttyva /dev/ttyx3 /dev/ttyyc
/dev/tty13 /dev/tty36 /dev/tty59 /dev/ttyb0 /dev/ttyc9 /dev/ttye2 /dev/ttypb /dev/ttyr4 /dev/ttys9 /dev/ttyu2 /dev/ttyvb /dev/ttyx4 /dev/ttyyd
/dev/tty14 /dev/tty37 /dev/tty6 /dev/ttyb1 /dev/ttyca /dev/ttye3 /dev/ttypc /dev/ttyr5 /dev/ttysa /dev/ttyu3 /dev/ttyvc /dev/ttyx5 /dev/ttyye
/dev/tty15 /dev/tty38 /dev/tty60 /dev/ttyb2 /dev/ttycb /dev/ttye4 /dev/ttypd /dev/ttyr6 /dev/ttysb /dev/ttyu4 /dev/ttyvd /dev/ttyx6 /dev/ttyyf
/dev/tty16 /dev/tty39 /dev/tty61 /dev/ttyb3 /dev/ttycc /dev/ttye5 /dev/ttype /dev/ttyr7 /dev/ttysc /dev/ttyu5 /dev/ttyve /dev/ttyx7 /dev/ttyz0
/dev/tty17 /dev/tty4 /dev/tty62 /dev/ttyb4 /dev/ttycd /dev/ttye6 /dev/ttypf /dev/ttyr8 /dev/ttysd /dev/ttyu6 /dev/ttyvf /dev/ttyx8 /dev/ttyz1
/dev/tty18 /dev/tty40 /dev/tty63 /dev/ttyb5 /dev/ttyce /dev/ttye7 /dev/ttyq0 /dev/ttyr9 /dev/ttyse /dev/ttyu7 /dev/ttyw0 /dev/ttyx9 /dev/ttyz2
/dev/tty19 /dev/tty41 /dev/tty7 /dev/ttyb6 /dev/ttycf /dev/ttye8 /dev/ttyq1 /dev/ttyra /dev/ttysf /dev/ttyu8 /dev/ttyw1 /dev/ttyxa /dev/ttyz3
/dev/tty2 /dev/tty42 /dev/tty8 /dev/ttyb7 /dev/ttyd0 /dev/ttye9 /dev/ttyq2 /dev/ttyrb /dev/ttyt0 /dev/ttyu9 /dev/ttyw2 /dev/ttyxb /dev/ttyz4
/dev/tty20 /dev/tty43 /dev/tty9 /dev/ttyb8 /dev/ttyd1 /dev/ttyea /dev/ttyq3 /dev/ttyrc /dev/ttyt1 /dev/ttyua /dev/ttyw3 /dev/ttyxc /dev/ttyz5
/dev/tty21 /dev/tty44 /dev/ttya0 /dev/ttyb9 /dev/ttyd2 /dev/ttyeb /dev/ttyq4 /dev/ttyrd /dev/ttyt2 /dev/ttyub /dev/ttyw4 /dev/ttyxd /dev/ttyz6
/dev/tty22 /dev/tty45 /dev/ttya1 /dev/ttyba /dev/ttyd3 /dev/ttyec /dev/ttyq5 /dev/ttyre /dev/ttyt3 /dev/ttyuc /dev/ttyw5 /dev/ttyxe /dev/ttyz7
/dev/tty23 /dev/tty46 /dev/ttya2 /dev/ttybb /dev/ttyd4 /dev/ttyed /dev/ttyq6 /dev/ttyrf /dev/ttyt4 /dev/ttyud /dev/ttyw6 /dev/ttyxf /dev/ttyz8
/dev/tty24 /dev/tty47 /dev/ttya3 /dev/ttybc /dev/ttyd5 /dev/ttyee /dev/ttyq7 /dev/ttys0 /dev/ttyt5 /dev/ttyue /dev/ttyw7 /dev/ttyy0 /dev/ttyz9
/dev/tty25 /dev/tty48 /dev/ttya4 /dev/ttybd /dev/ttyd6 /dev/ttyef /dev/ttyq8 /dev/ttyS0 /dev/ttyt6 /dev/ttyuf /dev/ttyw8 /dev/ttyy1 /dev/ttyza
/dev/tty26 /dev/tty49 /dev/ttya5 /dev/ttybe /dev/ttyd7 /dev/ttyp0 /dev/ttyq9 /dev/ttys1 /dev/ttyt7 /dev/ttyv0 /dev/ttyw9 /dev/ttyy2 /dev/ttyzb
/dev/tty27 /dev/tty5 /dev/ttya6 /dev/ttybf /dev/ttyd8 /dev/ttyp1 /dev/ttyqa /dev/ttyS1 /dev/ttyt8 /dev/ttyv1 /dev/ttywa /dev/ttyy3 /dev/ttyzc
/dev/tty28 /dev/tty50 /dev/ttya7 /dev/ttyc0 /dev/ttyd9 /dev/ttyp2 /dev/ttyqb /dev/ttys2 /dev/ttyt9 /dev/ttyv2 /dev/ttywb /dev/ttyy4 /dev/ttyzd
/dev/tty29 /dev/tty51 /dev/ttya8 /dev/ttyc1 /dev/ttyda /dev/ttyp3 /dev/ttyqc /dev/ttyS2 /dev/ttyta /dev/ttyv3 /dev/ttywc /dev/ttyy5 /dev/ttyze
/dev/tty3 /dev/tty52 /dev/ttya9 /dev/ttyc2 /dev/ttydb /dev/ttyp4 /dev/ttyqd /dev/ttys3 /dev/ttytb /dev/ttyv4 /dev/ttywd /dev/ttyy6 /dev/ttyzf
carmelo@AMD64:~$
