Vodafone station revolution - ethernet

[garresg]

Buongiorno a tutti.
Ho di recente installato la fibra a 300mega con la vodafone station revolution.
Nessun problema per configurare il wireless. Non riesco però a connettermi con il cavo ethernet. Ho controllato con il precedente router adsl e tutto funziona correttamente ma non se collego la vodafone station tramite cavo.
Ho Ubuntu 15.10
Qualcuno saprebbe darmi una mano?

Ecco un pò di informazioni:

Codice: Seleziona tutto

marcello@marcello-K52F:~$ lsb_release -ds && uname -m
Ubuntu 15.10
x86_64
marcello@marcello-K52F:~$ ^C
marcello@marcello-K52F:~$ $DESKTOP_SESSION
ubuntu: comando non trovato
marcello@marcello-K52F:~$ echo $DESKTOP_SESSION
ubuntu
marcello@marcello-K52F:~$ lspci -nn | grep -i net
02:00.0 Network controller [0280]: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
04:00.5 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 03)
marcello@marcello-K52F:~$ sudo lshw -C network
[sudo] password di marcello: 
  *-network               
       description: Wireless interface
       product: AR9285 Wireless Network Adapter (PCI-Express)
       vendor: Qualcomm Atheros
       physical id: 0
       bus info: pci@0000:02:00.0
       logical name: wlan0
       version: 01
       serial: 48:5d:60:97:e8:31
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless
       configuration: broadcast=yes driver=ath9k driverversion=4.2.0-19-generic firmware=N/A ip=192.168.1.7 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn
       resources: irq:17 memory:d2c00000-d2c0ffff
  *-network
       description: Ethernet interface
       product: JMC250 PCI Express Gigabit Ethernet Controller
       vendor: JMicron Technology Corp.
       physical id: 0.5
       bus info: pci@0000:04:00.5
       logical name: eth0
       version: 03
       serial: bc:ae:c5:a0:80:43
       size: 10Mbit/s
       capacity: 1Gbit/s
       width: 32 bits
       clock: 33MHz
       capabilities: pm pciexpress msix msi bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=jme driverversion=1.0.8 duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s
       resources: irq:32 memory:d0400000-d0403fff ioport:a100(size=128) ioport:a000(size=256)
marcello@marcello-K52F:~$ sudo ifconfig -a
eth0      Link encap:Ethernet  IndirizzoHW bc:ae:c5:a0:80:43  
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisioni:0 txqueuelen:1000 
          Byte RX:0 (0.0 B)  Byte TX:0 (0.0 B)
          Interrupt:32 

lo        Link encap:Loopback locale  
          indirizzo inet:127.0.0.1  Maschera:255.0.0.0
          indirizzo inet6: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:3507 errors:0 dropped:0 overruns:0 frame:0
          TX packets:3507 errors:0 dropped:0 overruns:0 carrier:0
          collisioni:0 txqueuelen:0 
          Byte RX:513372 (513.3 KB)  Byte TX:513372 (513.3 KB)

wlan0     Link encap:Ethernet  IndirizzoHW 48:5d:60:97:e8:31  
          indirizzo inet:192.168.1.7  Bcast:192.168.1.255  Maschera:255.255.255.0
          indirizzo inet6: fe80::4a5d:60ff:fe97:e831/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:12209 errors:0 dropped:0 overruns:0 frame:0
          TX packets:9722 errors:0 dropped:0 overruns:0 carrier:0
          collisioni:0 txqueuelen:1000 
          Byte RX:10278697 (10.2 MB)  Byte TX:1474087 (1.4 MB)

marcello@marcello-K52F:~$

[giulux]

Inseriti come hai fatto i listati rendono il post troppo lungo e di difficile lettura.
In futuro incollali tra i tag [ code] e [ /code] che si creano cliccando su Codice in alto, sopra la finestra di scrittura (editor completo) così:

• [ code]listato
  da postare[ /code]

Correggi il post precedente cliccando su "modifica", poi evidenzia il listato, clicca su Codice e salva

Ciao

[garresg]

Grazie Giulux.