Forum Ubuntu-it • Ubuntu vede la rete ma non si connette

Pagina 1 di 1

Ubuntu vede la rete ma non si connette

Inviato: domenica 8 gennaio 2017, 18:24

da matepaco

Buongiorno a tutti.
Purtroppo la mia scheda madre ha cominciato a non funzionare più così l'ho cambiata. Un modello molto simile, tra l'altro, per non perdere l'installazione di windows (in dual boot). Su windows tutto ok, wireless compreso.
Ubuntu ho deciso invece di formattarlo e reinstallarlo. Ha qualche problemino tra cui quello col wireless: vede la rete ma non si connette

Codice: Seleziona tutto

$ dmesg
....
[   84.667720] wlp3s7: authenticate with f4:f2:6d:c6:f0:67
[   84.673053] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 1/3)
[   84.738930] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 2/3)
[   84.801343] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 3/3)
[   84.872573] wlp3s7: authentication with f4:f2:6d:c6:f0:67 timed out
[   92.411266] IPv6: ADDRCONF(NETDEV_UP): wlp3s7: link is not ready

questo è l'output di dmesg... Già con la vecchia mobo avevo avuto i primi problemi. Li bastava disabilitare il wifi e riabilitarlo e di solito ad un certo punto si connetteva. Ma pensavo fosse un altro dei difetti della mobo e non ci davo peso.
Altre info sul mio sistema:

Codice: Seleziona tutto

$ uname -a
Linux gigabyte 4.8.0-32-generic #34-Ubuntu SMP Tue Dec 13 14:30:43 UTC 2016 x86_64 x86_64 x86_64 GNU/Linux

naturalmente aggiornato, via cavo

Codice: Seleziona tutto

$ lspci -vv
00:00.0 Host bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD9x0/RX980 Host Bridge (rev 02)
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] RD9x0/RX980 Host Bridge
	Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Capabilities: <access denied>

00:02.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890/RD9x0/RX980 PCI to PCI bridge (PCI Express GFX port 0) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 25
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: fea00000-feafffff
	Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:09.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] RD890/RD9x0/RX980 PCI to PCI bridge (PCI Express GPP Port 4) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 24
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	Memory behind bridge: fe900000-fe9fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:11.0 SATA controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] (rev 40) (prog-if 01 [AHCI 1.0])
	Subsystem: Gigabyte Technology Co., Ltd SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32
	Interrupt: pin A routed to IRQ 19
	Region 0: I/O ports at f040 [size=8]
	Region 1: I/O ports at f030 [size=4]
	Region 2: I/O ports at f020 [size=8]
	Region 3: I/O ports at f010 [size=4]
	Region 4: I/O ports at f000 [size=16]
	Region 5: Memory at feb0b000 (32-bit, non-prefetchable) [size=1K]
	Capabilities: <access denied>
	Kernel driver in use: ahci
	Kernel modules: ahci

00:12.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
	Subsystem: Gigabyte Technology Co., Ltd SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at feb0a000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci-pci

00:12.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
	Subsystem: Gigabyte Technology Co., Ltd SB7x0/SB8x0/SB9x0 USB EHCI Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at feb09000 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci

00:13.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
	Subsystem: Gigabyte Technology Co., Ltd SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at feb08000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci-pci

00:13.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
	Subsystem: Gigabyte Technology Co., Ltd SB7x0/SB8x0/SB9x0 USB EHCI Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at feb07000 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci

00:14.0 SMBus: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller (rev 42)
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 SMBus Controller
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Kernel driver in use: piix4_smbus
	Kernel modules: i2c_piix4, sp5100_tco

00:14.2 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 Azalia (Intel HDA) (rev 40)
	Subsystem: Gigabyte Technology Co., Ltd SBx00 Azalia (Intel HDA)
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at feb00000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel

00:14.3 ISA bridge: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller (rev 40)
	Subsystem: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 LPC host controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

00:14.4 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] SBx00 PCI to PCI Bridge (rev 40) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
	Memory behind bridge: fe800000-fe8fffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:14.5 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI2 Controller (prog-if 10 [OHCI])
	Subsystem: Gigabyte Technology Co., Ltd SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at feb06000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci-pci

00:15.0 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: fe700000-fe7fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:15.1 PCI bridge: Advanced Micro Devices, Inc. [AMD/ATI] SB700/SB800/SB900 PCI to PCI bridge (PCIE port 1) (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
	Memory behind bridge: fe600000-fe6fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:16.0 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB OHCI0 Controller (prog-if 10 [OHCI])
	Subsystem: Gigabyte Technology Co., Ltd SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at feb05000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci-pci

00:16.2 USB controller: Advanced Micro Devices, Inc. [AMD/ATI] SB7x0/SB8x0/SB9x0 USB EHCI Controller (prog-if 20 [EHCI])
	Subsystem: Gigabyte Technology Co., Ltd SB7x0/SB8x0/SB9x0 USB EHCI Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at feb04000 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci

00:18.0 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor HyperTransport Configuration
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Capabilities: <access denied>

00:18.1 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Address Map
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.2 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor DRAM Controller
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.3 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Miscellaneous Control
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Capabilities: <access denied>
	Kernel driver in use: k10temp
	Kernel modules: k10temp

00:18.4 Host bridge: Advanced Micro Devices, Inc. [AMD] Family 10h Processor Link Control
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] Barts PRO [Radeon HD 6850] (prog-if 00 [VGA controller])
	Subsystem: ASUSTeK Computer Inc. EAH6850 [Radeon HD 6850]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 34
	Region 0: Memory at d0000000 (64-bit, prefetchable) [size=256M]
	Region 2: Memory at fea20000 (64-bit, non-prefetchable) [size=128K]
	Region 4: I/O ports at e000 [size=256]
	Expansion ROM at 000c0000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel driver in use: radeon
	Kernel modules: radeon

01:00.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] Barts HDMI Audio [Radeon HD 6800 Series]
	Subsystem: ASUSTeK Computer Inc. Barts HDMI Audio [Radeon HD 6800 Series]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 36
	Region 0: Memory at fea40000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel

02:00.0 USB controller: ASMedia Technology Inc. Device 1343 (prog-if 30 [XHCI])
	Subsystem: Gigabyte Technology Co., Ltd Device 5007
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 26
	Region 0: Memory at fe900000 (64-bit, non-prefetchable) [size=32K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd

03:07.0 Network controller: Qualcomm Atheros AR5416 Wireless Network Adapter [AR5008 802.11(a)bgn] (rev 01)
	Subsystem: Qualcomm Atheros AR5416 Wireless Network Adapter [AR5008 802.11(a)bgn]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 168, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 21
	Region 0: Memory at fe800000 (32-bit, non-prefetchable) [size=64K]
	Capabilities: <access denied>
	Kernel driver in use: ath9k
	Kernel modules: ath9k

04:00.0 Ethernet controller: Qualcomm Atheros Killer E2400 Gigabit Ethernet Controller (rev 10)
	Subsystem: Gigabyte Technology Co., Ltd Killer E2400 Gigabit Ethernet Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 37
	Region 0: Memory at fe700000 (64-bit, non-prefetchable) [size=256K]
	Region 2: I/O ports at d000 [size=128]
	Capabilities: <access denied>
	Kernel driver in use: alx
	Kernel modules: alx

05:00.0 USB controller: VIA Technologies, Inc. VL805 USB 3.0 Host Controller (rev 01) (prog-if 30 [XHCI])
	Subsystem: Gigabyte Technology Co., Ltd VL805 USB 3.0 Host Controller
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 32
	Region 0: Memory at fe600000 (64-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd

da cui si vede che ho una scheda che va con ath9k

Codice: Seleziona tutto

$ dmesg | grep ath9k
[    4.779140] ath9k 0000:03:07.0 wlp3s7: renamed from wlan0

ho già provato ad aggiungere

Codice: Seleziona tutto

options iwlwifi 11n_disable=1 wd_disable=1

ad /etc/modprobe.d/iwlwifi.conf come visto su alcuni post ma niente...
Qualche idea?

Re: Ubuntu vede la rete ma non si connette

Inviato: domenica 8 gennaio 2017, 19:17

da magozurlinux

Da terminale postami questi comandi:

Codice: Seleziona tutto

sudo ifconfig -a

Codice: Seleziona tutto

iwconfig

Re: Ubuntu vede la rete ma non si connette

Inviato: domenica 8 gennaio 2017, 20:28

da matepaco

Intanto grazie:

Codice: Seleziona tutto

$ sudo ifconfig -a
enp4s0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.1.108  netmask 255.255.255.0  broadcast 192.168.1.255
        inet6 fe80::3e9e:9e0c:24e7:4d94  prefixlen 64  scopeid 0x20<link>
        ether 1c:1b:0d:67:e5:e7  txqueuelen 1000  (Ethernet)
        RX packets 1364  bytes 1060900 (1.0 MB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 1412  bytes 150344 (150.3 KB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 16  

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1  (Loopback locale)
        RX packets 4601  bytes 287701 (287.7 KB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 4601  bytes 287701 (287.7 KB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlp3s7: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether b0:48:7a:f3:a7:d8  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

Codice: Seleziona tutto

$ iwconfig
enp4s0    no wireless extensions.

wlp3s7    IEEE 802.11  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=20 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Power Management:off
          
lo        no wireless extensions.

Re: Ubuntu vede la rete ma non si connette

Inviato: domenica 8 gennaio 2017, 20:37

da Vir1966

Prova a dare:

Codice: Seleziona tutto

sudo ifconfig wlp3s7 up

Re: Ubuntu vede la rete ma non si connette

Inviato: domenica 8 gennaio 2017, 21:51

da matepaco

ok. fatto ma non cambia nulla... Il comando non da output di errore ma non si connette ancora

Re: Ubuntu vede la rete ma non si connette

Inviato: domenica 8 gennaio 2017, 23:03

da Vir1966

Per capire meglio ....vede la rete ma non si connette dopo aver messo la chiave WEP?

Re: Ubuntu vede la rete ma non si connette

Inviato: lunedì 9 gennaio 2017, 11:59

da matepaco

Si esatto. Dal gestore vedo in elenco molte reti tra cui la mia. Se ci clicco sopra comincia a provare a connettersi (la prima volta mi ha chiesto la password, WPA2) ma dopo un po' si arrende. Da dmesg vedo il solito messaggio

Re: Ubuntu vede la rete ma non si connette

Inviato: lunedì 9 gennaio 2017, 12:04

da magozurlinux

Da terminale postami questo comando:

Codice: Seleziona tutto

dmesg | grep ath

Re: Ubuntu vede la rete ma non si connette

Inviato: lunedì 9 gennaio 2017, 12:11

da matepaco

Codice: Seleziona tutto

 $ dmesg | grep ath
[    4.630118] ath: EEPROM regdomain: 0x809c
[    4.630120] ath: EEPROM indicates we should expect a country code
[    4.630120] ath: doing EEPROM country->regdmn map search
[    4.630121] ath: country maps to regdmn code: 0x52
[    4.630122] ath: Country alpha2 being used: CN
[    4.630122] ath: Regpair used: 0x52
[    4.899023] ath9k 0000:03:07.0 wlp3s7: renamed from wlan0

Re: Ubuntu vede la rete ma non si connette

Inviato: lunedì 9 gennaio 2017, 12:41

da magozurlinux

Da terminale dai questi comandi:

Codice: Seleziona tutto

sudo rm /etc/modprobe.d/iwlwifi.conf

questi comandi vanno dati una volta sola:

Codice: Seleziona tutto

echo options ath9k nohwcrypt=1 | sudo tee /etc/modprobe.d/ath9k.conf

Codice: Seleziona tutto

echo "options cfg80211 ieee80211_regdom=EU" | sudo tee /etc/modprobe.d/cfg80211.conf

riavvia il portatile.

Re: Ubuntu vede la rete ma non si connette

Inviato: lunedì 9 gennaio 2017, 12:59

da Vir1966

matepaco [url=http://forum.ubuntu-it.org/viewtopic.php?p=4948606#p4948606][img]http://forum.ubuntu-it.org/images/icons/icona-cita.gif[/img][/url] ha scritto:Si esatto. Dal gestore vedo in elenco molte reti tra cui la mia. Se ci clicco sopra comincia a provare a connettersi (la prima volta mi ha chiesto la password, WPA2) ma dopo un po' si arrende. Da dmesg vedo il solito messaggio

Era successo anche a me su un portatile con Xubuntu 16.04....poi ho cliccato sull'icona di rete , impostazioni e impostazioni della rete wifi a cui dovevo connettermi e ho salvato la password nell'apposito campo.....e il pc si è connesso.
Magari lo hai gia fatto, in caso prova...non si sa mai

Re: Ubuntu vede la rete ma non si connette

Inviato: lunedì 9 gennaio 2017, 16:03

da matepaco

@magozurlinux: fatto tutto. Riavviato il pc (è un fisso) e niente. Non si connette come al solito

Codice: Seleziona tutto

dmesg
...
[   76.127748] IPv6: ADDRCONF(NETDEV_UP): wlp3s7: link is not ready
[   91.698949] IPv6: ADDRCONF(NETDEV_UP): wlp3s7: link is not ready
[   91.734310] IPv6: ADDRCONF(NETDEV_UP): wlp3s7: link is not ready
[  104.959733] wlp3s7: authenticate with f4:f2:6d:c6:f0:67
[  104.964036] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 1/3)
[  105.074089] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 2/3)
[  105.147418] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 3/3)
[  105.211711] wlp3s7: authentication with f4:f2:6d:c6:f0:67 timed out
[  106.147170] wlp3s7: authenticate with f4:f2:6d:c6:f0:67
[  106.151675] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 1/3)
[  106.268586] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 2/3)
[  106.301411] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 3/3)
[  106.326442] wlp3s7: authentication with f4:f2:6d:c6:f0:67 timed out
[  107.662073] wlp3s7: authenticate with f4:f2:6d:c6:f0:67
[  107.667367] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 1/3)
[  107.739179] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 2/3)
[  107.809816] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 3/3)
[  107.849852] wlp3s7: authentication with f4:f2:6d:c6:f0:67 timed out
[  109.689423] wlp3s7: authenticate with f4:f2:6d:c6:f0:67
[  109.694349] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 1/3)
[  109.777026] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 2/3)
[  109.827039] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 3/3)
[  109.872917] wlp3s7: authentication with f4:f2:6d:c6:f0:67 timed out

Codice: Seleziona tutto

$ dmesg | grep ath
[    4.980725] ath: EEPROM regdomain: 0x809c
[    4.980726] ath: EEPROM indicates we should expect a country code
[    4.980727] ath: doing EEPROM country->regdmn map search
[    4.980727] ath: country maps to regdmn code: 0x52
[    4.980728] ath: Country alpha2 being used: CN
[    4.980728] ath: Regpair used: 0x52
[    5.230860] ath9k 0000:03:07.0 wlp3s7: renamed from wlan0

@Vir1966: Avevo già controllato. Lo spazio per la Password è già riempito corretamente

Re: Ubuntu vede la rete ma non si connette

Inviato: lunedì 9 gennaio 2017, 17:47

da magozurlinux

Hai l'IPv6 attivo.

Clicca in alto a dx sull'icona di NM, vai in basso su Modifica connessioni...; clicca su Senza fili, seleziona la tua rete wireless, clicca su Modifica, vai su Impostazioni IPv6, mettilo su Ignora e clicca in basso a dx su Salva.

Disconnettiti e poi ti riconnetti; prova la connessione.

Re: Ubuntu vede la rete ma non si connette

Inviato: mercoledì 11 gennaio 2017, 7:02

da matepaco

@magozurlinux: fatto pure questo. Non si connette però forse è diventato un po' più veloce a darmi il segnale di mancata connessione... magra consolazione...

Re: Ubuntu vede la rete ma non si connette

Inviato: mercoledì 11 gennaio 2017, 7:49

da enziosavio

Che possa mancare linux-firmware

Re: Ubuntu vede la rete ma non si connette

Inviato: mercoledì 11 gennaio 2017, 17:47

da magozurlinux

Da terminale postami questi comandi:

Codice: Seleziona tutto

route -n

Codice: Seleziona tutto

dmesg | grep wlp3s7

Re: Ubuntu vede la rete ma non si connette

Inviato: mercoledì 11 gennaio 2017, 21:04

da matepaco

@enziosavio: controllato. già installato alla versione più recente

@magozurlinux: Con ethernet attiva

Codice: Seleziona tutto

$ route -n
Tabella di routing IP del kernel
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         192.168.1.1     0.0.0.0         UG    100    0        0 enp4s0
169.254.0.0     0.0.0.0         255.255.0.0     U     1000   0        0 enp4s0
192.168.1.0     0.0.0.0         255.255.255.0   U     100    0        0 enp4s0

con wireless che non si connette

Codice: Seleziona tutto

 $ route -n
Tabella di routing IP del kernel
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface

Codice: Seleziona tutto

$ dmesg | grep wlp3s7
[    4.843434] ath9k 0000:03:07.0 wlp3s7: renamed from wlan0
[    4.905113] IPv6: ADDRCONF(NETDEV_UP): wlp3s7: link is not ready
[    4.910928] IPv6: ADDRCONF(NETDEV_UP): wlp3s7: link is not ready
[    5.043760] IPv6: ADDRCONF(NETDEV_UP): wlp3s7: link is not ready
[  353.531574] wlp3s7: authenticate with f4:f2:6d:c6:f0:67
[  353.537679] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 1/3)
[  353.614204] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 2/3)
[  353.686110] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 3/3)
[  353.741007] wlp3s7: authentication with f4:f2:6d:c6:f0:67 timed out
[  354.683238] wlp3s7: authenticate with f4:f2:6d:c6:f0:67
[  354.687268] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 1/3)
[  354.768958] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 2/3)
[  354.810556] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 3/3)
[  354.860231] wlp3s7: authentication with f4:f2:6d:c6:f0:67 timed out
[  356.211213] wlp3s7: authenticate with f4:f2:6d:c6:f0:67
[  356.216872] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 1/3)
[  356.288416] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 2/3)
[  356.343886] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 3/3)
[  356.403179] wlp3s7: authentication with f4:f2:6d:c6:f0:67 timed out
[  358.249799] wlp3s7: authenticate with f4:f2:6d:c6:f0:67
[  358.256453] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 1/3)
[  358.329951] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 2/3)
[  358.422455] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 3/3)
[  358.526316] wlp3s7: authentication with f4:f2:6d:c6:f0:67 timed out
[  370.185909] wlp3s7: authenticate with f4:f2:6d:c6:f0:67
[  370.191329] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 1/3)
[  370.269190] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 2/3)
[  370.357667] wlp3s7: send auth to f4:f2:6d:c6:f0:67 (try 3/3)
[  370.429143] wlp3s7: authentication with f4:f2:6d:c6:f0:67 timed out

C'è ancora quell'errore IPV6 ma sulla scheda della connessione è selezionato "ignora"