Forum Ubuntu-it

Buon giorno a tutti,
avrei un problema con il portatile di cui a titolo con xubuntu 16.10 come s.o.
Non si connette al router fastweb tramite il wifi pur vedendo la rete.
questo è quello che mi restituisce dando il comando lspci

00:00.0 Host bridge: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx DMI Bridge
00:02.0 VGA compatible controller: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller
00:02.1 Display controller: Intel Corporation Atom Processor D4xx/D5xx/N4xx/N5xx Integrated Graphics Controller
00:1b.0 Audio device: Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 02)
00:1d.0 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 (rev 02)
00:1d.1 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 (rev 02)
00:1d.2 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 (rev 02)
00:1d.3 USB controller: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 (rev 02)
00:1d.7 USB controller: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation NM10 Family LPC Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation NM10/ICH7 Family SATA Controller [AHCI mode] (rev 02)
00:1f.3 SMBus: Intel Corporation NM10/ICH7 Family SMBus Controller (rev 02)
01:00.0 Ethernet controller: Qualcomm Atheros AR8152 v1.1 Fast Ethernet (rev c1)
02:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak]

Qualche suggerimento?
Grazie

In base cosa credi che veda la rete, almeno da quel comando?

Prova a vdere con "ifconfig -a" se si connette alla wireless

02:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak]

questa è la scheda wireless
posta l'output tra i tag 'codice' i driver li hai installati?

ecco:
*-network
description: Ethernet interface
product: AR8152 v1.1 Fast Ethernet
vendor: Qualcomm Atheros
physical id: 0
bus info: pci@0000:01:00.0
logical name: enp1s0
version: c1
serial: 1c:75:08:a5:23:4a
size: 100Mbit/s
capacity: 100Mbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI duplex=full ip=192.168.1.74 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s
resources: irq:30 memory:57000000-5703ffff ioport:5000(size=128)
*-network
description: Wireless interface
product: Centrino Wireless-N 1000 [Condor Peak]
vendor: Intel Corporation
physical id: 0
bus info: pci@0000:02:00.0
logical name: wlp2s0
version: 00
serial: 00:26:c7:c4:aa:68
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=iwlwifi driverversion=4.8.0-34-generic firmware=39.31.5.1 build 35138 ip=10.42.0.1 latency=0 link=yes multicast=yes wireless=IEEE 802.11
resources: irq:28 memory:56000000-56001fff

Inseriti come hai fatto i listati rendono il post troppo lungo e di difficile lettura.
In futuro incollali tra i tag [ code] [ /code] che si creano cliccando su Codice in alto, sopra la finestra di scrittura (editor completo) così:

• [ code]listato
  da postare[ /code]

Correggi il post precedente cliccando su "modifica, poi seleziona il listato, clicca su Codice e salva

Ciao

posta qui l'output del comando in questo comando

Posta anche questi comandi: