Ubuntu 7.04: niente rete

[silent911]

Ho appena installato la ubuntu 7.04 e non riesco ad andare su internet...mi spiego meglio.
Se attivo il dhcp non ottengo niente (niente ip, netmask, gateway), se imposto i parametri manualmente non riesco nè a navigare ne a pingare gli altri utenti della lan... siccome ho due pc collegati in contemporanea uso uno swithch avendo una sola presa ethernet in camera.

Provando in un'altra camera della stessa lan (stavolta senza switch) riesco a prendere indirizzo, netmask ecc.. ma non riesco nè a navigare nè a pingare siti. se invece provo a pingare un altro utente della lan otenngo host unreacheable...

A cosa potrebbe essere dovuto? Con altre distribuzioni linux e con windows riesco a navigare quindi escluderei problemi al mio switch...

[melchiorre]

A volte il problema c'è se si è effettuato un aggiornamento da edgy, ma se non è il tuo caso non saprei

[silent911]

sto provando e riprovando: a volte prende solo l'indirizzo, a volte non prende niente....

[silent911]

dopo aver settato gliindirizzi a mano tramite l'interfaccia grafica, se do sudo ifconfig mi fa vedere

eth0
          inet6


etho: avah
          inet addr:169.254.4.166  mask 255.255.0.0


mentre io avevo settato un 192.168.

[silent911]

Ho scaricato nuovamente l'immagine della live e ho avviato la stessa...
indirizzo, gateway, mask e dns sono ok...ma non pinga e non va su internet...
ma cosa può essere???? sto pensando che è come se fosse bloccato da un firewall...

[Ptah]

Intanto leva il protocollo ipv6 che tanto non ti serve a nulla...e poi riprova, sia mai che è quello :d

[silent911]

che comando devo dare per togliere l'ipv6?

[samburu]

La tua linea o la tua periferica (modem / router) perché se imposti il dhcp e non parte...

[silent911]

La tua linea o la tua periferica (modem / router) perché se imposti il dhcp e non parte...

la linea funziona... se uso lo stesso pc con windows funziona tutto

[samburu]

La tua connessione è attiva? Vai nel pannello connessioni e controlla. A volte può capitare che per qualche remota ragione la scheda si disattivi, o sia disattivata di default. Altro caso (a me capitato) era che con windows voleva il bridging, mentre con Ubuntu no...al tuo posto proverei con uno e poi l'altro. Per farlo devi entrare fisicamente nel modem.

[silent911]

se vado in /var/log/messages trovo

NETDEV WATCHDOG: eth0: transmit timed out
eth0: link down

[silent911]

forse si riesce a capire qualcosa in più: se do il dmesg ottengo

irq 23: nobody cared (try booting  with the "irqpoll" option )

se poi faccio un cat di /proc/interrupts

al 23 ho eth0 che è la mia scheda di rete

[silent911]

Ho risolto il problema

nel file /boot/grub/menu.lst basta aggiungere

noapic pci=noacpi

alla voce ubuntu

[gibe]

anche io ho un problema analogo ....sto cercando il collegamento da qualche giorno ....il pc non fa il ping con il router.

per provare la tua soluzione ti chiedo " dove hai aggiunto la riga??

all' ultimo rigo scrivo

ubuntu    noapic pci=noacpi

ok cosi???

gibe

[silent911]

no sono più preciso
nel file /boot/grub/menu.lst
cambia la riga

kernel /boot/vmlinuz-2.6.20-15-generic root=UUID=882cd01e-4f7c-4cec-b684-d0807e3c9bd5 ro quiet splash

in

kernel /boot/vmlinuz-2.6.20-15-generic root=UUID=882cd01e-4f7c-4cec-b684-d0807e3c9bd5 noapic pci=noacpi ro quiet splash

[gibe]

nel mio caso non funziona :'(

dopo la modifica ho fatto restart ma non pingavo neanche sulla scheda di rete

incomincio a pensare che il problema sta nel router che non riesce a dialogare con ubuntu??

posso verificare questo??

gibe

[silent911]

Nn mi sono chiare alcune cose:

• usi un portatile o un fisso?
• se scrivi ping 127.0.0.1 va a buon fine?
• su windows va tutto bene?
• dai sudo dmesg e postalo

[gibe]

uso un portatile acer per ubuntu
sul router è connesso un pc con windows xp che funziona bene

quando accendo il portatile e provo a fare un ifconfig la scheda non ha indirizzo e la luce verde è spenta ::)

poi come root
ifconfig eth0 192.168.1.100 (pongo l' indirizzo statico alla scheda)

a questo punto verifico con un ifconfig (ora la scheda ha un ip)

provo a pingare ping 192.168.1.100 (lo fa)

provo a pingare il router ping 192.168.1.1 (non lo fa Unreachable)

provo a pingare ping 127.0.0.1 (lo fa!!! ma su cosa ho pingato??)

poi do il comando dmesg

mi da una serie di istruzioni  (un po lungo!!!! )
root@giuseppe-laptop:/home/giuseppe# dmesg
[17179569.184000] Linux version 2.6.17-10-generic (root@vernadsky) (gcc version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #2 SMP Fri Oct 13 18:45:35 UTC 2006 (Ubuntu 2.6.17-10.33-generic)
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[17179569.184000]  BIOS-e820: 0000000000100000 - 0000000026ff0000 (usable)
[17179569.184000]  BIOS-e820: 0000000026ff0000 - 0000000026ffffc0 (ACPI data)
[17179569.184000]  BIOS-e820: 0000000026ffffc0 - 0000000027000000 (ACPI NVS)
[17179569.184000]  BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 623MB LOWMEM available.
[17179569.184000] On node 0 totalpages: 159728
[17179569.184000]  DMA zone: 4096 pages, LIFO batch:0
[17179569.184000]  Normal zone: 155632 pages, LIFO batch:31
[17179569.184000] DMI 2.3 present.
[17179569.184000] ACPI: RSDP (v000 OID_00                                ) @ 0x000e4010
[17179569.184000] ACPI: RSDT (v001 OID_00 RSDT_000 0x30303030 �& 0x00010007) @ 0x26fffbc0
[17179569.184000] ACPI: FADT (v002 INSYDE FACP_000 0x00000100 �& 0x00010007) @ 0x26fffac0
[17179569.184000] ACPI: BOOT (v001 INSYDE SYS_BOOT 0x00000100 �& 0x00010007) @ 0x26fffb50
[17179569.184000] ACPI: DBGP (v001 INSYDE SYS_DBGP 0x00000100 �& 0x00010007) @ 0x26fffb80
[17179569.184000] ACPI: DSDT (v001 INSYDE  VT8362 0x00001000 MSFT 0x0100000d) @ 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0x1008
[17179569.184000] Allocating PCI resources starting at 30000000 (gap: 27000000:d8f80000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: root=/dev/hda1 ro quiet splash
[17179569.184000] Local APIC disabled by BIOS (or by default) -- you can enable it with "lapic"
[17179569.184000] mapped APIC to ffffd000 (014ec000)
[17179569.184000] Enabling fast FPU save and restore... done.
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[17179569.184000] Detected 1200.283 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179571.344000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[17179571.348000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179571.384000] Memory: 623208k/638912k available (1910k kernel code, 15136k reserved, 1070k data, 308k init, 0k highmem)
[17179571.384000] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[17179571.464000] Calibrating delay using timer specific routine.. 2402.61 BogoMIPS (lpj=4805238)
[17179571.464000] Security Framework v1.0.0 initialized
[17179571.464000] SELinux:  Disabled at boot.
[17179571.464000] Mount-cache hash table entries: 512
[17179571.464000] CPU: After generic identify, caps: 0183f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000
[17179571.464000] CPU: After vendor identify, caps: 0183f9ff c1cbf9ff 00000000 00000000 00000000 00000000 00000000
[17179571.464000] Enabling disabled K7/SSE Support.
[17179571.464000] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[17179571.464000] CPU: L2 Cache: 256K (64 bytes/line)
[17179571.464000] CPU: After all inits, caps: 0383f9ff c1cbf9ff 00000000 00000420 00000000 00000000 00000000
[17179571.464000] Checking 'hlt' instruction... OK.
[17179571.480000] SMP alternatives: switching to UP code
[17179571.480000] Freeing SMP alternatives: 16k freed
[17179571.480000] checking if image is initramfs... it is
[17179572.296000] Freeing initrd memory: 5563k freed
[17179572.296000] ACPI: Core revision 20060707
[17179572.296000] ACPI: Looking for DSDT ... not found!
[17179572.300000] ACPI: setting ELCR to 0200 (from 0c00)
[17179572.308000] CPU0: AMD mobile AMD Athlon(tm) XP 1400+  stepping 00
[17179572.308000] SMP motherboard not detected.
[17179572.308000] Local APIC not detected. Using dummy APIC emulation.
[17179572.308000] Brought up 1 CPUs
[17179572.308000] migration_cost=0
[17179572.308000] NET: Registered protocol family 16
[17179572.308000] EISA bus registered
[17179572.308000] ACPI: bus type pci registered
[17179572.308000] PCI: PCI BIOS revision 2.10 entry at 0xe8a64, last bus=1
[17179572.308000] PCI: Using configuration type 1
[17179572.308000] Setting up standard PCI resources
[17179572.364000] ACPI: Interpreter enabled
[17179572.364000] ACPI: Using PIC for interrupt routing
[17179572.368000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179572.368000] PCI: Probing PCI hardware (bus 00)
[17179572.368000] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[17179572.368000] Disabling VIA memory write queue (PCI ID 0305, rev 80): [55] 3c & 1f -> 1c
[17179572.368000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:11.1
[17179572.368000] Boot video device is 0000:01:00.0
[17179572.368000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179572.380000] ACPI: Embedded Controller [EC0] (gpe 1) interrupt mode.
[17179572.380000] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 *11)
[17179572.380000] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
[17179572.380000] ACPI: PCI Interrupt Link [LNKC] (IRQs 10) *11
[17179572.380000] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 *11)
[17179572.384000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179572.384000] pnp: PnP ACPI init
[17179572.384000] PCI: setting IRQ 13 as level-triggered
[17179572.388000] pnp: PnP ACPI: found 11 devices
[17179572.388000] PnPBIOS: Disabled by ACPI PNP
[17179572.388000] PCI: Using ACPI for IRQ routing
[17179572.388000] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[17179572.388000] PCI: Cannot allocate resource region 0 of device 0000:00:0a.0
[17179572.388000] pnp: 00:07: ioport range 0x1600-0x167f has been reserved
[17179572.388000] pnp: 00:07: ioport range 0x2c8-0x2cf has been reserved
[17179572.388000] pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
[17179572.388000] pnp: 00:07: ioport range 0x1000-0x105f could not be reserved
[17179572.388000] PCI: Bridge: 0000:00:01.0
[17179572.388000]  IO window: c000-dfff
[17179572.388000]  MEM window: e0000000-efffffff
[17179572.388000]  PREFETCH window: 90000000-9fffffff
[17179572.388000] PCI: Bus 2, cardbus bridge: 0000:00:0a.0
[17179572.388000]  IO window: 00001400-000014ff
[17179572.388000]  IO window: 00001800-000018ff
[17179572.388000]  PREFETCH window: 30000000-31ffffff
[17179572.388000]  MEM window: 32000000-33ffffff
[17179572.388000] PCI: Setting latency timer of device 0000:00:01.0 to 64
[17179572.388000] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[17179572.388000] PCI: setting IRQ 11 as level-triggered
[17179572.388000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[17179572.388000] NET: Registered protocol family 2
[17179572.424000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[17179572.424000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[17179572.428000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[17179572.428000] TCP: Hash tables configured (established 131072 bind 65536)
[17179572.428000] TCP reno registered
[17179572.428000] Simple Boot Flag at 0x37 set to 0x1
[17179572.428000] audit: initializing netlink socket (disabled)
[17179572.428000] audit(1179664128.428:1): initialized
[17179572.432000] VFS: Disk quotas dquot_6.5.1
[17179572.432000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179572.432000] Initializing Cryptographic API
[17179572.432000] io scheduler noop registered
[17179572.432000] io scheduler anticipatory registered
[17179572.432000] io scheduler deadline registered
[17179572.432000] io scheduler cfq registered (default)
[17179572.432000] Applying VIA southbridge workaround.
[17179572.432000] isapnp: Scanning for PnP cards...
[17179572.784000] isapnp: No Plug & Play device found
[17179572.824000] Real Time Clock Driver v1.12ac
[17179572.824000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[17179572.824000] mice: PS/2 mouse device common for all mice
[17179572.824000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[17179572.824000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179572.824000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[17179572.824000] PNP: PS/2 Controller [PNP0303:KBC,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[17179572.840000] i8042.c: Detected active multiplexing controller, rev 1.1.
[17179572.848000] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[17179572.848000] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[17179572.852000] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[17179572.852000] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[17179572.856000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179572.856000] EISA: Probing bus 0 at eisa.0
[17179572.856000] Cannot allocate resource for EISA slot 1
[17179572.856000] EISA: Detected 0 cards.
[17179572.856000] TCP bic registered
[17179572.856000] NET: Registered protocol family 1
[17179572.856000] NET: Registered protocol family 8
[17179572.856000] NET: Registered protocol family 20
[17179572.856000] Using IPI No-Shortcut mode
[17179572.856000] ACPI: (supports S0 S3 S4 S5)
[17179572.856000] Freeing unused kernel memory: 308k freed
[17179573.164000] input: AT Translated Set 2 keyboard as /class/input/input0
[17179574.124000] Capability LSM initialized
[17179574.184000] ACPI: CPU0 (power states: C1[C1] C2[C2])
[17179574.188000] ACPI: Thermal Zone [THRM] (54 C)
[17179575.076000] VP_IDE: IDE controller at PCI slot 0000:00:11.1
[17179575.076000] VP_IDE: chipset revision 6
[17179575.076000] VP_IDE: not 100% native mode: will probe irqs later
[17179575.076000] VP_IDE: VIA vt8231 (rev 10) IDE UDMA100 controller on pci0000:00:11.1
[17179575.076000]    ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda:DMA, hdb:pio
[17179575.076000]    ide1: BM-DMA at 0x1108-0x110f, BIOS settings: hdc:DMA, hdd:pio
[17179575.076000] Probing IDE interface ide0...
[17179575.492000] hda: TOSHIBA MK2018GAP, ATA DISK drive
[17179576.164000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[17179576.644000] Probing IDE interface ide1...
[17179577.512000] hdc: QSI CD-ROM SCR-242, ATAPI CD/DVD-ROM drive
[17179577.848000] ide1 at 0x170-0x177,0x376 on irq 15
[17179577.860000] hda: max request size: 128KiB
[17179577.872000] hda: 39070080 sectors (20003 MB), CHS=38760/16/63, UDMA(100)
[17179577.872000] hda: cache flushes supported
[17179577.872000]  hda: hda1 hda2
[17179577.984000] hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
[17179577.984000] Uniform CD-ROM driver Revision: 3.20
[17179578.408000] usbcore: registered new driver usbfs
[17179578.408000] usbcore: registered new driver hub
[17179578.408000] USB Universal Host Controller Interface driver v3.0
[17179578.408000] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[17179578.408000] ACPI: PCI Interrupt 0000:00:11.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
[17179578.408000] uhci_hcd 0000:00:11.2: UHCI Host Controller
[17179578.412000] uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
[17179578.412000] uhci_hcd 0000:00:11.2: irq 11, io base 0x00001200
[17179578.412000] usb usb1: configuration #1 chosen from 1 choice
[17179578.412000] hub 1-0:1.0: USB hub found
[17179578.412000] hub 1-0:1.0: 2 ports detected
[17179578.592000] Attempting manual resume
[17179578.684000] kjournald starting.  Commit interval 5 seconds
[17179578.684000] EXT3-fs: mounted filesystem with ordered data mode.
[17179596.200000] via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker
[17179596.200000] PCI: Enabling device 0000:00:12.0 (0005 -> 0007)
[17179596.200000] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[17179596.244000] Linux agpgart interface v0.101 (c) Dave Jones
[17179596.332000] eth0: VIA Rhine II at 0x1e800, 00:c0:9f:10:0a:a8, IRQ 11.
[17179596.332000] eth0: MII PHY found at address 1, status 0x7829 advertising 01e1 Link 45e1.
[17179596.356000] agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
[17179596.364000] agpgart: AGP aperture is 64M @ 0xa0000000
[17179596.788000] parport_pc: VIA 686A/8231 detected
[17179596.788000] parport_pc: probing current configuration
[17179596.788000] parport_pc: Current parallel port base: 0x378
[17179596.788000] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[17179596.812000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179596.864000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179596.884000] parport_pc: VIA parallel port: io=0x378, irq=7
[17179597.160000] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[17179597.160000] Yenta: CardBus bridge found at 0000:00:0a.0 [1025:001d]
[17179597.160000] Yenta O2: res at 0x94/0xD4: 00/ea
[17179597.160000] Yenta O2: enabling read prefetch/write burst
[17179597.288000] Yenta: ISA IRQ mask 0x0438, PCI irq 11
[17179597.288000] Socket status: 30000007
[17179597.312000] irda_init()
[17179597.312000] NET: Registered protocol family 23
[17179597.548000] input: PC Speaker as /class/input/input1
[17179597.820000] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[17179597.820000] PCI: setting IRQ 10 as level-triggered
[17179597.820000] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[17179597.820000] PCI: Via IRQ fixup for 0000:00:11.5, from 11 to 10
[17179597.820000] PCI: Setting latency timer of device 0000:00:11.5 to 64
[17179597.864000] Floppy drive(s): fd0 is 1.44M
[17179597.884000] FDC 0 is a post-1991 82077
[17179598.036000] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[17179598.116000] input: PS/2 Mouse as /class/input/input2
[17179598.148000] input: AlpsPS/2 ALPS GlidePoint as /class/input/input3
[17179598.204000] ts: Compaq touchscreen protocol output
[17179598.332000] ACPI: PCI Interrupt 0000:00:11.6[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[17179598.332000] PCI: Via IRQ fixup for 0000:00:11.6, from 11 to 10
[17179598.424000] cs: IO port probe 0x100-0x3af: clean.
[17179598.428000] cs: IO port probe 0x3e0-0x4ff: clean.
[17179598.428000] cs: IO port probe 0x820-0x8ff: clean.
[17179598.428000] cs: IO port probe 0xc00-0xcf7: clean.
[17179598.428000] cs: IO port probe 0xa00-0xaff: clean.
[17179599.084000] PCI: Setting latency timer of device 0000:00:11.6 to 64
[17179599.140000] NET: Registered protocol family 17
[17179599.692000] MC'97 0 converters and GPIO not ready (0x1)
[17179600.240000] lp0: using parport0 (interrupt-driven).
[17179600.308000] Adding 827308k swap on /dev/disk/by-uuid/451e53b1-2fc0-4eef-b8ad-a514780a1f31.  Priority:-1 extents:1 across:827308k
[17179600.416000] EXT3 FS on hda1, internal journal
[17179602.796000] ACPI: AC Adapter [ADP0] (on-line)
[17179602.860000] ACPI: Battery Slot [BAT0] (battery present)
[17179602.892000] ACPI: Power Button (FF) [PWRF]
[17179602.892000] ACPI: Lid Switch [LID]
[17179602.892000] ACPI: Power Button (CM) [PBTN]
[17179603.108000] ibm_acpi: ec object not found
[17179603.152000] pcc_acpi: loading...
[17179603.340000] ACPI: Video Device [VGA0] (multi-head: yes  rom: no  post: no)
[17179603.724000] powernow: PowerNOW! Technology present. Can scale: frequency and voltage.
[17179603.732000] powernow: SGTC: 10000
[17179603.732000] powernow: Minimum speed 500 MHz. Maximum speed 1200 MHz.
[17179607.480000] mtrr: no more MTRRs available
[17179608.336000] [drm] Initialized drm 1.0.1 20051102
[17179608.404000] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[17179608.408000] [drm] Initialized savage 2.4.1 20050313 on minor 0
[17179608.408000] mtrr: 0x90000000,0x8000000 overlaps existing 0x90000000,0x1000000
[17179608.408000] mtrr: 0x90000000,0x2000000 overlaps existing 0x90000000,0x1000000
[17179608.408000] mtrr: base(0x92000000) is not aligned on a size(0x5000000) boundary
[17179608.412000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[17179608.412000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[17179608.412000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[17179609.636000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[17179609.636000] apm: overridden by ACPI.
[17179615.392000] Bluetooth: Core ver 2.8
[17179615.392000] NET: Registered protocol family 31
[17179615.392000] Bluetooth: HCI device and connection manager initialized
[17179615.392000] Bluetooth: HCI socket layer initialized
[17179615.432000] Bluetooth: L2CAP ver 2.8
[17179615.432000] Bluetooth: L2CAP socket layer initialized
[17179615.628000] Bluetooth: RFCOMM socket layer initialized
[17179615.628000] Bluetooth: RFCOMM TTY layer initialized
[17179615.628000] Bluetooth: RFCOMM ver 1.7
[17179624.300000] NET: Registered protocol family 10
[17179624.300000] lo: Disabled Privacy Extensions

e allora come sono messo??? :'(

gibe