Pagina 1 di 1

ho installato tor e non mi funziona internet

Inviato: giovedì 4 settembre 2008, 12:05
da mrsocotra
ho installato tor ma quando lo attivo con il tor button  non mi naviga e sta fermo sulla pagina dalla quale lo ho attivato.
suggerimenti? grazie.

Re: ho installato tor e non mi funziona internet

Inviato: giovedì 4 settembre 2008, 12:06
da alberto t.
ciao
segui questa mia guida :)

Re: ho installato tor e non mi funziona internet

Inviato: giovedì 4 settembre 2008, 12:23
da mrsocotra
l'ho seguita ma il problema persiste, allego il file di config
Ho tagliato l'inizio perchè se no non stava in un messaggio
#
#  3. DEBUGGING
#
#  These options are mainly useful when tracing a problem. Note that
#  you might also want to invoke Privoxy with the --no-daemon command
#  line option when debugging.
#
#
#
#  3.1. debug
#
#  Specifies:
#
#      Key values that determine what information gets logged.
#
#  Type of value:
#
#      Integer values
#
#  Default value:
#
#       0 (i.e.: only fatal errors (that cause Privoxy to exit) are logged)
#
#  Effect if unset:
#
#      Default value is used (see above).
#
#  Notes:
#
#      The available debug levels are:
#
#        debug         1 # log each request destination (and the crunch reason if Privoxy intercepted the request)
#        debug         2 # show each connection status
#        debug         4 # show I/O status
#        debug         8 # show header parsing
#        debug        16 # log all data written to the network into the logfile
#        debug        32 # debug force feature
#        debug        64 # debug regular expression filters
#        debug       128 # debug redirects
#        debug       256 # debug GIF de-animation
#        debug       512 # Common Log Format
#        debug      1024 # debug kill pop-ups
#        debug      2048 # CGI user interface
#        debug      4096 # Startup banner and warnings.  
#        debug      8192 # Non-fatal errors
#
#
#      To select multiple debug levels, you can either add them or
#      use multiple debug lines.
#
#      A debug level of 1 is informative because it will show you each
#      request as it happens. 1, 4096 and 8192 are recommended so that you
#      will notice when things go wrong. The other levels are probably only
#      of interest if you are hunting down a specific problem. They can
#      produce a hell of an output (especially 16).
#
#      Privoxy used to ship with the debug levels recommended above enabled
#      by default, but due to privacy concerns 3.0.7 and later are
#      configured to only log fatal errors.
#
#      If you are used to the more verbose settings, simply enable the debug
#      lines below again.
#
#      If you want to use pure CLF (Common Log Format), you should set
#      debug 512 ONLY and not enable anything else.
#
#      Privoxy has a hard-coded limit for the length of log messages. If
#      it's reached, messages are logged truncated and marked with
#      "... [too long, truncated]".
#
#      Please don't file any support requests without trying to reproduce
#      the problem with increased debug level first. Once you read the log
#      messages, you may even be able to solve the problem on your own.
#
#debug   1    # log each request destination (and the crunch reason if Privoxy intercepted the request)
#debug   4096 # Startup banner and warnings
#debug   8192 # Non-fatal errors
#
#
#  3.2. single-threaded
#
#  Specifies:
#
#      Whether to run only one server thread.
#
#  Type of value:
#
#      None
#
#  Default value:
#
#      Unset
#
#  Effect if unset:
#
#      Multi-threaded (or, where unavailable: forked) operation,
#      i.e. the ability to serve multiple requests simultaneously.
#
#  Notes:
#
#      This option is only there for debugging purposes. It will
#      drastically reduce performance.
#
#single-threaded
#
#
#  4. ACCESS CONTROL AND SECURITY
#
#  This section of the config file controls the security-relevant
#  aspects of Privoxy's configuration.
#
#
#
#  4.1. listen-address
#
#  Specifies:
#
#      The IP address and TCP port on which Privoxy will listen for
#      client requests.
#
#  Type of value:
#
#      [IP-Address]:Port
#
#  Default value:
#
#      127.0.0.1:8118
#
#  Effect if unset:
#
#      Bind to 127.0.0.1 (localhost), port 8118. This is suitable and
#      recommended for home users who run Privoxy on the same machine
#      as their browser.
#
#  Notes:
#
#      You will need to configure your browser(s) to this proxy address
#      and port.
#
#      If you already have another service running on port 8118, or
#      if you want to serve requests from other machines (e.g. on your
#      local network) as well, you will need to override the default.
#
#      If you leave out the IP address, Privoxy will bind to all
#      interfaces (addresses) on your machine and may become reachable
#      from the Internet. In that case, consider using access control
#      lists (ACL's, see below), and/or a firewall.
#
#      If you open Privoxy to untrusted users, you will also
#      want to make sure that the following actions are disabled:
#      enable-edit-actions and enable-remote-toggle
#
#  Example:
#
#      Suppose you are running Privoxy on a machine which has the
#      address 192.168.0.1 on your local private network (192.168.0.0)
#      and has another outside connection with a different address. You
#      want it to serve requests from inside only:
#
#        listen-address  192.168.0.1:8118
#
#
listen-address  127.0.0.1:8118
#
#
#  4.2. toggle
#
#  Specifies:
#
#      Initial state of "toggle" status
#
#  Type of value:
#
#      1 or 0
#
#  Default value:
#
#      1
#
#  Effect if unset:
#
#      Act as if toggled on
#
#  Notes:
#
#      If set to 0, Privoxy will start in "toggled off" mode,
#      i.e. mostly behave like a normal, content-neutral proxy
#      with both ad blocking and content filtering disabled. See
#      enable-remote-toggle below.
#
#      The windows version will only display the toggle icon in the
#      system tray if this option is present.
#
toggle  1
#
#
#  4.3. enable-remote-toggle
#
#  Specifies:
#
#      Whether or not the web-based toggle feature may be used
#
#  Type of value:
#
#      0 or 1
#
#  Default value:
#
#      0
#
#  Effect if unset:
#
#      The web-based toggle feature is disabled.
#
#  Notes:
#
#      When toggled off, Privoxy mostly acts like a normal,
#      content-neutral proxy, i.e. doesn't block ads or filter content.
#
#      Access to the toggle feature can not be controlled separately by
#      "ACLs" or HTTP authentication, so that everybody who can access
#      Privoxy (see "ACLs" and listen-address above) can toggle it
#      for all users. So this option is not recommended for multi-user
#      environments with untrusted users.
#
#      Note that malicious client side code (e.g Java) is also capable
#      of using this option.
#
#      As a lot of Privoxy users don't read documentation, this feature
#      is disabled by default.
#
#      Note that you must have compiled Privoxy with support for this
#      feature, otherwise this option has no effect.
#
enable-remote-toggle  0
#
#
#  4.4. enable-remote-http-toggle
#
#  Specifies:
#
#      Whether or not Privoxy recognizes special HTTP headers to change
#      its behaviour.
#
#  Type of value:
#
#      0 or 1
#
#  Default value:
#
#      0
#
#  Effect if unset:
#
#      Privoxy ignores special HTTP headers.
#
#  Notes:
#
#      When toggled on, the client can change Privoxy's behaviour by
#      setting special HTTP headers. Currently the only supported
#      special header is "X-Filter: No", to disable filtering for
#      the ongoing request, even if it is enabled in one of the
#      action files.
#
#      This feature is disabled by default. If you are using Privoxy in
#      a environment with trusted clients, you may enable this feature
#      at your discretion. Note that malicious client side code (e.g
#      Java) is also capable of using this feature.
#
#      This option will be removed in future releases as it has been
#      obsoleted by the more general header taggers.
#
enable-remote-http-toggle  0
#
#
#  4.5. enable-edit-actions
#
#  Specifies:
#
#      Whether or not the web-based actions file editor may be used
#
#  Type of value:
#
#      0 or 1
#
#  Default value:
#
#      0
#
#  Effect if unset:
#
#      The web-based actions file editor is disabled.
#
#  Notes:
#
#      Access to the editor can not be controlled separately by
#      "ACLs" or HTTP authentication, so that everybody who can access
#      Privoxy (see "ACLs" and listen-address above) can modify its
#      configuration for all users.
#
#      This option is not recommended for environments with untrusted
#      users and as a lot of Privoxy users don't read documentation,
#      this feature is disabled by default.
#
#      Note that malicious client side code (e.g Java) is also capable
#      of using the actions editor and you shouldn't enable this
#      options unless you understand the consequences and are sure
#      your browser is configured correctly.
#
#      Note that you must have compiled Privoxy with support for this
#      feature, otherwise this option has no effect.
#
enable-edit-actions 0
#
#
#  4.6. enforce-blocks
#
#  Specifies:
#
#      Whether the user is allowed to ignore blocks and can "go there
#      anyway".
#
#  Type of value:
#
#      0 or 1
#
#  Default value:
#
#      0
#
#  Effect if unset:
#
#      Blocks are not enforced.
#
#  Notes:
#
#      Privoxy is mainly used to block and filter requests as a service
#      to the user, for example to block ads and other junk that clogs
#      the pipes.  Privoxy's configuration isn't perfect and sometimes
#      innocent pages are blocked. In this situation it makes sense to
#      allow the user to enforce the request and have Privoxy ignore
#      the block.
#
#      In the default configuration Privoxy's "Blocked" page contains
#      a "go there anyway" link to adds a special string (the force
#      prefix) to the request URL. If that link is used, Privoxy
#      will detect the force prefix, remove it again and let the
#      request pass.
#
#      Of course Privoxy can also be used to enforce a network
#      policy. In that case the user obviously should not be able to
#      bypass any blocks, and that's what the "enforce-blocks" option
#      is for. If it's enabled, Privoxy hides the "go there anyway"
#      link. If the user adds the force prefix by hand, it will not
#      be accepted and the circumvention attempt is logged.
#
#  Examples:
#
#      enforce-blocks 1
#
enforce-blocks 0
#
#
#  4.7. ACLs: permit-access and deny-access
#
#  Specifies:
#
#      Who can access what.
#
#  Type of value:
#
#      src_addr[/src_masklen] [dst_addr[/dst_masklen]]
#
#      Where src_addr and dst_addr are IP addresses in dotted decimal
#      notation or valid DNS names, and src_masklen and dst_masklen are
#      subnet masks in CIDR notation, i.e. integer values from 2 to 30
#      representing the length (in bits) of the network address. The
#      masks and the whole destination part are optional.
#
#  Default value:
#
#      Unset
#
#  Effect if unset:
#
#      Don't restrict access further than implied by listen-address
#
#  Notes:
#
#      Access controls are included at the request of ISPs and systems
#      administrators, and are not usually needed by individual
#      users. For a typical home user, it will normally suffice to
#      ensure that Privoxy only listens on the localhost (127.0.0.1)
#      or internal (home) network address by means of the listen-address
#      option.
#
#      Please see the warnings in the FAQ that Privoxy is not intended
#      to be a substitute for a firewall or to encourage anyone to
#      defer addressing basic security weaknesses.
#
#      Multiple ACL lines are OK. If any ACLs are specified, Privoxy
#      only talks to IP addresses that match at least one permit-access
#      line and don't match any subsequent deny-access line. In other
#      words, the last match wins, with the default being deny-access.
#
#      If Privoxy is using a forwarder (see forward below) for a
#      particular destination URL, the dst_addr that is examined is
#      the address of the forwarder and NOT the address of the ultimate
#      target. This is necessary because it may be impossible for the
#      local Privoxy to determine the IP address of the ultimate target
#      (that's often what gateways are used for).
#
#      You should prefer using IP addresses over DNS names, because
#      the address lookups take time. All DNS names must resolve! You
#      can not use domain patterns like "*.org" or partial domain
#      names. If a DNS name resolves to multiple IP addresses, only
#      the first one is used.
#
#      Denying access to particular sites by ACL may have undesired
#      side effects if the site in question is hosted on a machine
#      which also hosts other sites (most sites are).
#
#  Examples:
#
#      Explicitly define the default behavior if no ACL and
#      listen-address are set: "localhost" is OK. The absence of a
#      dst_addr implies that all destination addresses are OK:
#
#        permit-access  localhost
#
#
#      Allow any host on the same class C subnet as www.privoxy.org
#      access to nothing but www.example.com (or other domains hosted
#      on the same system):
#
#        permit-access  www.privoxy.org/24 www.example.com/32
#
#
#      Allow access from any host on the 26-bit subnet 192.168.45.64 to
#      anywhere, with the exception that 192.168.45.73 may not access
#      the IP address behind www.dirty-stuff.example.com:
#
#        permit-access  192.168.45.64/26
#        deny-access   192.168.45.73  www.dirty-stuff.example.com
#
#
#
#  4.8. buffer-limit
#
#  Specifies:
#
#      Maximum size of the buffer for content filtering.
#
#  Type of value:
#
#      Size in Kbytes
#
#  Default value:
#
#      4096
#
#  Effect if unset:
#
#      Use a 4MB (4096 KB) limit.
#
#  Notes:
#
#      For content filtering, i.e. the +filter and +deanimate-gif
#      actions, it is necessary that Privoxy buffers the entire document
#      body. This can be potentially dangerous, since a server could
#      just keep sending data indefinitely and wait for your RAM to
#      exhaust -- with nasty consequences.  Hence this option.
#
#      When a document buffer size reaches the buffer-limit, it is
#      flushed to the client unfiltered and no further attempt to filter
#      the rest of the document is made. Remember that there may be
#      multiple threads running, which might require up to buffer-limit
#      Kbytes each, unless you have enabled "single-threaded" above.
#
buffer-limit 4096
#
#
#  5. FORWARDING
#
#  This feature allows routing of HTTP requests through a chain of
#  multiple proxies.
#
#  Forwarding can be used to chain Privoxy with a caching proxy to
#  speed up browsing. Using a parent proxy may also be necessary if
#  the machine that Privoxy runs on has no direct Internet access.
#
#  Note that parent proxies can severely decrease your privacy
#  level. For example a parent proxy could add your IP address to the
#  request headers and if it's a caching proxy it may add the "Etag"
#  header to revalidation requests again, even though you configured
#  Privoxy to remove it. It may also ignore Privoxy's header time
#  randomization and use the original values which could be used by
#  the server as cookie replacement to track your steps between visits.
#
#  Also specified here are SOCKS proxies. Privoxy supports the SOCKS
#  4 and SOCKS 4A protocols.
#
#
#
#  5.1. forward
#
#  Specifies:
#
#      To which parent HTTP proxy specific requests should be routed.
#
#  Type of value:
#
#      target_pattern http_parent[:port]
#
#      where target_pattern is a URL pattern that specifies to which
#      requests (i.e. URLs) this forward rule shall apply. Use /
#      to denote "all URLs".  http_parent[:port] is the DNS name or
#      IP address of the parent HTTP proxy through which the requests
#      should be forwarded, optionally followed by its listening port
#      (default: 8080). Use a single dot (.) to denote "no forwarding".
#
#  Default value:
#
#      Unset
#
#  Effect if unset:
#
#      Don't use parent HTTP proxies.
#
#  Notes:
#
#      If http_parent is ".", then requests are not forwarded to
#      another HTTP proxy but are made directly to the web servers.
#
#      Multiple lines are OK, they are checked in sequence, and the
#      last match wins.
#
#  Examples:
#
#      Everything goes to an example parent proxy, except SSL on port
#      443 (which it doesn't handle):
#
#        forward   /      parent-proxy.example.org:8080
#        forward   :443   .
#
#
#      Everything goes to our example ISP's caching proxy, except for
#      requests to that ISP's sites:
#
#        forward   /                  caching-proxy.isp.example.net:8000
#        forward   .isp.example.net   .
#
#
#
#
#  5.2. forward-socks4 and forward-socks4a
#
#  Specifies:
#
#      Through which SOCKS proxy (and optionally to which parent HTTP
#      proxy) specific requests should be routed.
#
#  Type of value:
#
#      target_pattern socks_proxy[:port] http_parent[:port]
#
#      where target_pattern is a URL pattern that specifies to which
#      requests (i.e. URLs) this forward rule shall apply. Use / to
#      denote "all URLs".  http_parent and socks_proxy are IP addresses
#      in dotted decimal notation or valid DNS names (http_parent may
#      be "." to denote "no HTTP forwarding"), and the optional port
#      parameters are TCP ports, i.e. integer values from 1 to 64535
#
#  Default value:
#
#      Unset
#
#  Effect if unset:
#
#      Don't use SOCKS proxies.
#
#  Notes:
#
#      Multiple lines are OK, they are checked in sequence, and the
#      last match wins.
#
#      The difference between forward-socks4 and forward-socks4a
#      is that in the SOCKS 4A protocol, the DNS resolution of the
#      target hostname happens on the SOCKS server, while in SOCKS 4
#      it happens locally.
#
#      If http_parent is ".", then requests are not forwarded to another
#      HTTP proxy but are made (HTTP-wise) directly to the web servers,
#      albeit through a SOCKS proxy.
#
#  Examples:
#
#      From the company example.com, direct connections are made to all
#      "internal" domains, but everything outbound goes through their
#      ISP's proxy by way of example.com's corporate SOCKS 4A gateway
#      to the Internet.
#
#        forward-socks4a   /       socks-gw.example.com:1080    www-cache.isp.example.net:8080
#        forward           .example.com        .
#
#
#      A rule that uses a SOCKS 4 gateway for all destinations but no
#      HTTP parent looks like this:
#
#        forward-socks4   /               socks-gw.example.com:1080  .
#
#
#      To chain Privoxy and Tor, both running on the same system,
#      you would use something like:
#
#        forward-socks4a   /               127.0.0.1:9050 .
#
#
#      The public Tor network can't be used to reach your local network,
#      if you need to access local servers you therefore might want
#      to make some exceptions:
#
#        forward         192.168.*.*/     .  
#        forward         10.*.*.*/        .  
#        forward         127.*.*.*/       .
#
#
#      Unencrypted connections to systems in these address ranges will
#      be as (un) secure as the local network is, but the alternative
#      is that you can't reach the local network through Privoxy at
#      all. Of course this may actually be desired and there is no
#      reason to make these exceptions if you aren't sure you need them.
#
#      If you also want to be able to reach servers in your local
#      network by using their names, you will need additional exceptions
#      that look like this:
#
#       forward           localhost/     .
#
#
#
#
#  5.3. forwarded-connect-retries
#
#  Specifies:
#
#      How often Privoxy retries if a forwarded connection request
#      fails.
#
#  Type of value:
#
#      Number of retries.
#
#  Default value:
#
#      0
#
#  Effect if unset:
#
#      Connections forwarded through other proxies are treated like
#      direct connections and no retry attempts are made.
#
#  Notes:
#
#      forwarded-connect-retries is mainly interesting for socks4a
#      connections, where Privoxy can't detect why the connections
#      failed. The connection might have failed because of a DNS timeout
#      in which case a retry makes sense, but it might also have failed
#      because the server doesn't exist or isn't reachable. In this
#      case the retry will just delay the appearance of Privoxy's
#      error message.
#
#      Note that in the context of this option, "forwarded connections"
#      includes all connections that Privoxy forwards through other
#      proxies. This option is not limited to the HTTP CONNECT method.
#
#      Only use this option, if you are getting lots of
#      forwarding-related error messages that go away when you try again
#      manually. Start with a small value and check Privoxy's logfile
#      from time to time, to see how many retries are usually needed.
#
#  Examples:
#
#      forwarded-connect-retries 1
#
forwarded-connect-retries  0
#
#
#  5.4. accept-intercepted-requests
#
#  Specifies:
#
#      Whether intercepted requests should be treated as valid.
#
#  Type of value:
#
#      0 or 1
#
#  Default value:
#
#      0
#
#  Effect if unset:
#
#      Only proxy requests are accepted, intercepted requests are
#      treated as invalid.
#
#  Notes:
#
#      If you don't trust your clients and want to force them to use
#      Privoxy, enable this option and configure your packet filter
#      to redirect outgoing HTTP connections into Privoxy.

#
#      Make sure that Privoxy's own requests aren't redirected as well.
#      Additionally take care that Privoxy can't intentionally connect
#      to itself, otherwise you could run into redirection loops if
#      Privoxy's listening port is reachable by the outside or an
#      attacker has access to the pages you visit.
#
#  Examples:
#
#      accept-intercepted-requests 1
#
accept-intercepted-requests 0
#
#
#  5.5. allow-cgi-request-crunching
#
#  Specifies:
#
#      Whether requests to Privoxy's CGI pages can be blocked or
#      redirected.
#
#  Type of value:
#
#      0 or 1
#
#  Default value:
#
#      0
#
#  Effect if unset:
#
#      Privoxy ignores block and redirect actions for its CGI pages.
#
#  Notes:
#
#      By default Privoxy ignores block or redirect actions for
#      its CGI pages.  Intercepting these requests can be useful in
#      multi-user setups to implement fine-grained access control,
#      but it can also render the complete web interface useless and
#      make debugging problems painful if done without care.
#
#      Don't enable this option unless you're sure that you really
#      need it.
#
#  Examples:
#
#      allow-cgi-request-crunching 1
#
allow-cgi-request-crunching 0
#
#
#  5.6. split-large-forms
#
#  Specifies:
#
#      Whether the CGI interface should stay compatible with broken
#      HTTP clients.
#
#  Type of value:
#
#      0 or 1
#
#  Default value:
#
#      0
#
#  Effect if unset:
#
#      The CGI form generate long GET URLs.
#
#  Notes:
#
#      Privoxy's CGI forms can lead to rather long URLs. This isn't
#      a problem as far as the HTTP standard is concerned, but it can
#      confuse clients with arbitrary URL length limitations.
#
#      Enabling split-large-forms causes Privoxy to divide big forms
#      into smaller ones to keep the URL length down. It makes editing
#      a lot less convenient and you can no longer submit all changes
#      at once, but at least it works around this browser bug.
#
#      If you don't notice any editing problems, there is no reason
#      to enable this option, but if one of the submit buttons appears
#      to be broken, you should give it a try.
#
#  Examples:
#
#      split-large-forms 1
#
split-large-forms 0
#
#
#  6. WINDOWS GUI OPTIONS
#
#  Privoxy has a number of options specific to the Windows GUI
#  interface:
#

#  If "activity-animation" is set to 1, the Privoxy icon will animate
#  when "Privoxy" is active. To turn off, set to 0.
#
#activity-animation   1

#  If "log-messages" is set to 1, Privoxy will log messages to the
#  console window:
#
#log-messages   1

#  If "log-buffer-size" is set to 1, the size of the log buffer,
#  i.e. the amount of memory used for the log messages displayed in
#  the console window, will be limited to "log-max-lines" (see below).
#
#  Warning: Setting this to 0 will result in the buffer to grow
#  infinitely and eat up all your memory!
#
#log-buffer-size 1

#  log-max-lines is the maximum number of lines held in the log
#  buffer. See above.
#
#log-max-lines 200

#  If "log-highlight-messages" is set to 1, Privoxy will highlight
#  portions of the log messages with a bold-faced font:
#
#log-highlight-messages 1

#  The font used in the console window:
#
#log-font-name Comic Sans MS

#  Font size used in the console window:
#
#log-font-size 8

#  "show-on-task-bar" controls whether or not Privoxy will appear as
#  a button on the Task bar when minimized:
#
#show-on-task-bar 0

#  If "close-button-minimizes" is set to 1, the Windows close button
#  will minimize Privoxy instead of closing the program (close with
#  the exit option on the File menu).
#
#close-button-minimizes 1

#  The "hide-console" option is specific to the MS-Win console version
#  of Privoxy.  If this option is used, Privoxy will disconnect from
#  and hide the command console.
#
#hide-console
#
#logfile logfile

#jarfile jarfile

#forward-socks4a /       localhost:9050  .

Re: ho installato tor e non mi funziona internet

Inviato: giovedì 4 settembre 2008, 12:26
da dj_def
se hai un router devi forwardare le porte che usa tor

inoltre la connessione sarà lenta, quindi aspetta un pò quando carichi le pagine

Re: ho installato tor e non mi funziona internet

Inviato: giovedì 4 settembre 2008, 12:37
da alberto t.
ciao
devi togliere il segno # davanti a:

Codice: Seleziona tutto

forward-socks4a /       localhost:9050  .
Ciao, Alberto

Re: ho installato tor e non mi funziona internet

Inviato: giovedì 4 settembre 2008, 15:46
da mrsocotra
fatto, ma non funziona lo stesso..

Re: ho installato tor e non mi funziona internet

Inviato: venerdì 5 settembre 2008, 19:50
da mrsocotra
up.. appena clicco sulla cipollina rossa per farla diventare verde(se è una cipolla :)) la connessione sembra bloccata e non mi carica più niente.