[Install] Installazione scanner Canon 3200F
[Install] Installazione scanner Canon 3200F
Salve a tutti!
Ho installato Ubuntu 7.10, ma ho problemi a far funzionare il mio scanner Canon 3200 F,mentre funziona regolarmente la mia stampante HP 3650.
Lanciando Xsane mi dà nessuna periferica collegata, ma su Preferenze>Hardware information la vede regolarmente.
Nella pagina di aiuto di Ubuntu dllo sanner mi consiglia di installarlo manualmente, scaricando i driver cercando con Synaptics libsane extras, ma me lo dà già installato.
Potete aiutarmi?
Stefano
Ho installato Ubuntu 7.10, ma ho problemi a far funzionare il mio scanner Canon 3200 F,mentre funziona regolarmente la mia stampante HP 3650.
Lanciando Xsane mi dà nessuna periferica collegata, ma su Preferenze>Hardware information la vede regolarmente.
Nella pagina di aiuto di Ubuntu dllo sanner mi consiglia di installarlo manualmente, scaricando i driver cercando con Synaptics libsane extras, ma me lo dà già installato.
Potete aiutarmi?
Stefano
- slayer1971
- Prode Principiante
- Messaggi: 154
- Iscrizione: venerdì 22 dicembre 2006, 9:53
- Distribuzione: Ubuntu 12.04 LTS i686
- Località: Bari
Re: [Install] Installazione scanner Canon 3200F
Hai verificato la compatibilita su http://www.sane-project.org Ad occhio pare incerta la sua funzionalità
Re: [Install] Installazione scanner Canon 3200F
Stesso scanner, stesso problema.
Qualcuno sa come farlo andare? :'(
Qualcuno sa come farlo andare? :'(
- slayer1971
- Prode Principiante
- Messaggi: 154
- Iscrizione: venerdì 22 dicembre 2006, 9:53
- Distribuzione: Ubuntu 12.04 LTS i686
- Località: Bari
Re: [Install] Installazione scanner Canon 3200F
Se nel sito indicato non indica la compatibilità sarà dura, comunque qualcuno più esperto potrà aiutarvi se ci sono possibilità. La mia esperienza con uno scanner HP serie 3670 è stata triste alla fine ho installato Win su virtualbox per farlo funzionare. Spero tu risolva diversamente, perché sono costretto ad occupare 2G di spazio per uno scanner.Ciao
Re: [Install] Installazione scanner Canon 3200F
Vorrei spiegare meglio la questione: l' installazione dei driver di Windows per utilizzare lo scanner in questione,dovrebbe avvenire tramite un menu apposito in Sistema, installando ndigtk da Synaptics, come raccomandato nel menu di aiuto di Ubuntu, ho selezionato ndiswrapper per l' installazione ma poi questo menu non compare, forse la soluzione del problema sta qua.slayer1971 ha scritto: Se nel sito indicato non indica la compatibilità sarà dura, comunque qualcuno più esperto potrà aiutarvi se ci sono possibilità. La mia esperienza con uno scanner HP serie 3670 è stata triste alla fine ho installato Win su virtualbox per farlo funzionare. Spero tu risolva diversamente, perché sono costretto ad occupare 2G di spazio per uno scanner.Ciao
Grazie comunque per l' aiuto.
- slayer1971
- Prode Principiante
- Messaggi: 154
- Iscrizione: venerdì 22 dicembre 2006, 9:53
- Distribuzione: Ubuntu 12.04 LTS i686
- Località: Bari
Re: [Install] Installazione scanner Canon 3200F
Forse puoi essere tu ad aiutarmi:ndigtk si Synaptics non lo trovo, forse è un problema di repository, per quello che ho letto mi è sembrato che ndiswrapper fosse per l'installazione di schede wireless. Se hai voglia di descrivere i passaggi più dettagliatamente faccio delle prove e magari risolviamo entrambi. Magari puoi indicarmi l'indirizzo della guida che hai usato.Ciao
Ultima modifica di slayer1971 il martedì 18 dicembre 2007, 15:53, modificato 1 volta in totale.
Re: [Install] Installazione scanner Canon 3200F
Qualche novità sul fronte canon?
Ho trovato sul loro sito questo
Qualcuno ha qualche riferimento o è a conoscenza di qualcosa già esistente?
Ho trovato sul loro sito questo
Mi sembrerebbe giusto iniziare ora una petizione per spingere a cambiare politica come lo si è fatto con la ati!Canon sviluppa driver solo per Windows e Macintosh, non per Linux o altri sistemi operativi (ad esempio, PalmOS, Epoc o altri PDA).
Tuttavia, Canon offre programmi di sviluppo personalizzati per la seguente gamma di prodotti Canon:
# Fotocamere digitali
# Stampanti Bubble Jet
# Fotocopiatrici digitali GP e stampanti LBP
# Sistemi digitali iR multifunzionali
Le informazioni relative agli scanner sono riservate e non verranno distribuite; per questi prodotti, pertanto, non esiste alcun programma.
Qualcuno ha qualche riferimento o è a conoscenza di qualcosa già esistente?
-
supergigio91
- Prode Principiante
- Messaggi: 8
- Iscrizione: venerdì 13 giugno 2008, 11:10
- Località: San Martino B.A. Verona
Re: [Install] Installazione scanner Canon 3200F
idem!Fox -ino ha scritto: Stesso scanner, stesso problema.
Qualcuno sa come farlo andare? :'(
Alessandro
Re: [Install] Installazione scanner Canon 3200F
Proviamo a riepilogare un pò ...
inizialmente ho seguito questo percorso:
Assicurarsi di avere installati i pacchetti sane sane-utils libsane libsane-extras xsane (che riguardano xsane, il programma gnome predefinito in ubuntu per l’acquisizione di immagini da scanner). In caso contrario : [ sudo apt-get install sane sane-utils libsane libsane-extras xsane ]
2. Installare con [ sudo apt-get install scanbuttond ] il modulo scanbuttond, necessario per il corretto riconoscimento dello scanner
3. Far partire il modulo digitando nel terminale semplicemente [ scanbuttond ]
4. scollego la webcam (che inizialmente viene vista da GIMP) e poi lancio gimp/file/crea/xsane/device log ma non vede alcuno scanner.
lancio il comando da terminale sane-find-scanner -p ed ottengo:
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
# No USB scanners found. If you expected something different, make sure that
# you have loaded a kernel driver for your USB host controller and have setup
# the USB system correctly. See man sane-usb for details.
# No Mustek parallel port scanners found. If you expected something
# different, make sure the scanner is correctly connected to your computer
# and you have apropriate access rights.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.
# You may want to run this program as root to find all devices. Once you
# found the scanner devices, be sure to adjust access permissions as
# necessary.
provo a lanciare il comando sudo gedit /etc/sane.d/dll.conf ed ottengo:
# enable the next line if you want to allow access through the network:
net
abaton
agfafocus
apple
avision
artec
artec_eplus48u
as6e
bh
canon
canon630u
canon_pp
cardscan
coolscan
coolscan2
#dc25
#dc210
#dc240
dell1600n_net
dmc
epjitsu
epson
epson2
fujitsu
#gphoto2
genesys
gt68xx
hp
hp3900
hpsj5s
hp3500
hp4200
hp5400
hp5590
hpljm1005
hs2p
ibm
leo
lexmark
ma1509
matsushita
microtek
microtek2
mustek
#mustek_pp
mustek_usb
mustek_usb2
nec
niash
pie
pixma
plustek
#plustek_pp
#pnm
qcam
ricoh
s9036
sceptre
sharp
sm3600
sm3840
snapscan
sp15c
#st400
#stv680
tamarack
teco1
teco2
teco3
#test
u12
umax
#umax_pp
umax1220u
v4l
poi lancio il comando sudo gedit /etc/sane.d/canon_pp.conf ed ottengo l'apertura del file che è così configurato:
# Define which port to use if one isn't specified - you should only have
# one of these lines!
# This is the default port to be used - others will be detected
ieee1284 parport0
# Define the location of our pixel weight file, can begin with ~/ if needed.
# You can have as many of these as you like - lines with ports that don't exist
# will be ignored.
#
# Parameters are:
# calibrate /path/to/calibration-file port-name
#
# The format of port-name is dependant on your OS version.
#
# If a file isn't speficied, the default name will be
# ~/.sane/canon_pp-calibration-[port-name]
calibrate ~/.sane/canon_pp-calibration-pp0 parport0
# calibrate /etc/sane/my_calibration parport1
# Enable the next line if you're having trouble with ECP mode such as I/O
# errors. Nibble mode is slower, but more reliable.
force_nibble
# Set a default initialisation mode for each port. Valid modes are:
# AUTO (attempts to automatically detect by trying both methods)
FB620P (10101010 style.. also works for FB320P)
# FB630P (11001100 style.. also works for FB330P, N340P, N640P)
init_mode AUTO parport0
init_mode FB620P parport0
# init_mode FB630P parport0
Mi sapete dire cosa sbaglio (secondo me bisogna prima caricare i drive per lo scanner se no il sistema non lo vede mai ...)
Grazie a tutti
inizialmente ho seguito questo percorso:
Assicurarsi di avere installati i pacchetti sane sane-utils libsane libsane-extras xsane (che riguardano xsane, il programma gnome predefinito in ubuntu per l’acquisizione di immagini da scanner). In caso contrario : [ sudo apt-get install sane sane-utils libsane libsane-extras xsane ]
2. Installare con [ sudo apt-get install scanbuttond ] il modulo scanbuttond, necessario per il corretto riconoscimento dello scanner
3. Far partire il modulo digitando nel terminale semplicemente [ scanbuttond ]
4. scollego la webcam (che inizialmente viene vista da GIMP) e poi lancio gimp/file/crea/xsane/device log ma non vede alcuno scanner.
lancio il comando da terminale sane-find-scanner -p ed ottengo:
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
# No USB scanners found. If you expected something different, make sure that
# you have loaded a kernel driver for your USB host controller and have setup
# the USB system correctly. See man sane-usb for details.
# No Mustek parallel port scanners found. If you expected something
# different, make sure the scanner is correctly connected to your computer
# and you have apropriate access rights.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.
# You may want to run this program as root to find all devices. Once you
# found the scanner devices, be sure to adjust access permissions as
# necessary.
provo a lanciare il comando sudo gedit /etc/sane.d/dll.conf ed ottengo:
# enable the next line if you want to allow access through the network:
net
abaton
agfafocus
apple
avision
artec
artec_eplus48u
as6e
bh
canon
canon630u
canon_pp
cardscan
coolscan
coolscan2
#dc25
#dc210
#dc240
dell1600n_net
dmc
epjitsu
epson
epson2
fujitsu
#gphoto2
genesys
gt68xx
hp
hp3900
hpsj5s
hp3500
hp4200
hp5400
hp5590
hpljm1005
hs2p
ibm
leo
lexmark
ma1509
matsushita
microtek
microtek2
mustek
#mustek_pp
mustek_usb
mustek_usb2
nec
niash
pie
pixma
plustek
#plustek_pp
#pnm
qcam
ricoh
s9036
sceptre
sharp
sm3600
sm3840
snapscan
sp15c
#st400
#stv680
tamarack
teco1
teco2
teco3
#test
u12
umax
#umax_pp
umax1220u
v4l
poi lancio il comando sudo gedit /etc/sane.d/canon_pp.conf ed ottengo l'apertura del file che è così configurato:
# Define which port to use if one isn't specified - you should only have
# one of these lines!
# This is the default port to be used - others will be detected
ieee1284 parport0
# Define the location of our pixel weight file, can begin with ~/ if needed.
# You can have as many of these as you like - lines with ports that don't exist
# will be ignored.
#
# Parameters are:
# calibrate /path/to/calibration-file port-name
#
# The format of port-name is dependant on your OS version.
#
# If a file isn't speficied, the default name will be
# ~/.sane/canon_pp-calibration-[port-name]
calibrate ~/.sane/canon_pp-calibration-pp0 parport0
# calibrate /etc/sane/my_calibration parport1
# Enable the next line if you're having trouble with ECP mode such as I/O
# errors. Nibble mode is slower, but more reliable.
force_nibble
# Set a default initialisation mode for each port. Valid modes are:
# AUTO (attempts to automatically detect by trying both methods)
FB620P (10101010 style.. also works for FB320P)
# FB630P (11001100 style.. also works for FB330P, N340P, N640P)
init_mode AUTO parport0
init_mode FB620P parport0
# init_mode FB630P parport0
Mi sapete dire cosa sbaglio (secondo me bisogna prima caricare i drive per lo scanner se no il sistema non lo vede mai ...)
Grazie a tutti
Chi c’è in linea
Visualizzano questa sezione: 0 utenti iscritti e 10 ospiti
