vi posto quello che ho fatto e quindi fin dove arrivo... non riesco a capire cosa devo inserire al posto di "modulo"... in più se magare rilevate che ho sbagliato in qualcosa...
comando: sudo modprobe modulo
darioeman@darioeman-laptop:~$ sudo apt-get install lm-sensors
Lettura della lista dei pacchetti in corso... Fatto
Generazione dell'albero delle dipendenze in corso
Reading state information... Fatto
lm-sensors è già alla versione più recente.
0 aggiornati, 0 installati, 0 da rimuovere e 0 non aggiornati.
darioeman@darioeman-laptop:~$ gedit creadev.sh
darioeman@darioeman-laptop:~$ gedit creadev.sh
darioeman@darioeman-laptop:~$ gedit creadev.sh
darioeman@darioeman-laptop:~$ chmod 755 creadev.sh
chmod: cambio dei permessi di `creadev.sh': Funzione non permessa
darioeman@darioeman-laptop:~$ sudo chmod 755 creadev.sh
darioeman@darioeman-laptop:~$ sudo ./creadev.sh
/dev/i2c-0
/dev/i2c-1
/dev/i2c-2
/dev/i2c-3
/dev/i2c-4
/dev/i2c-5
/dev/i2c-6
/dev/i2c-7
/dev/i2c-8
/dev/i2c-9
/dev/i2c-10
/dev/i2c-11
/dev/i2c-12
/dev/i2c-13
/dev/i2c-14
/dev/i2c-15
/dev/i2c-16
/dev/i2c-17
/dev/i2c-18
/dev/i2c-19
/dev/i2c-20
/dev/i2c-21
/dev/i2c-22
/dev/i2c-23
/dev/i2c-24
/dev/i2c-25
/dev/i2c-26
/dev/i2c-27
/dev/i2c-28
/dev/i2c-29
/dev/i2c-30
/dev/i2c-31
darioeman@darioeman-laptop:~$ chmod 755 ricerca_sensori
darioeman@darioeman-laptop:~$ sudo ./ricerca_sensori
# sensors-detect revision $Revision$
This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.
We can start with probing for (PCI) I2C or SMBus adapters.
Do you want to probe now? (YES/no): yes
Probing for PCI bus adapters...
Sorry, no known PCI bus adapters found.
If you have undetectable or unsupported I2C/SMBus adapters, you can have
them scanned by manually loading the modules before running this script.
To continue, we need module `i2c-dev' to be loaded.
Do you want to load `i2c-dev' now? (YES/no): yes
Module loaded successfully.
We are now going to do the I2C/SMBus adapter probings. Some chips may
be double detected; we choose the one with the highest confidence
value in that case.
If you found that the adapter hung after probing a certain address,
you can specify that address to remain unprobed.
Some chips are also accessible through the ISA I/O ports. We have to
write to arbitrary I/O ports to probe them. This is usually safe though.
Yes, you do have ISA I/O ports even if you do not have any ISA slots!
Do you want to scan the ISA I/O ports? (YES/no): yes
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM78-J' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No
Some Super I/O chips may also contain sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): yes
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... Yes
Found unknown non-standard chip with ID 0x7a
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Fintek'... No
Trying family `ITE'... No
Some south bridges, CPUs or memory controllers may also contain
embedded sensors. Do you want to scan for them? (YES/no): yes
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... Success!
(driver `k8temp')
AMD K10 thermal sensors... No
Intel Core family thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
Driver `k8temp' (should be inserted):
Detects correctly:
* Chip `AMD K8 thermal sensors' (confidence: 9)
Do you want to overwrite /etc/sysconfig/lm_sensors? (YES/no): yes
Copy prog/init/lm_sensors.init to /etc/init.d/lm_sensors
for initialization at boot time.
You should now start the lm_sensors service to load the required
kernel modules.
Grazie mille per aver letto tutto
