con il comando
dmesg ricevo questo oput
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 502MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 128624) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 128624
[ 0.000000] HighMem 128624 -> 128624
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 128624
[ 0.000000] On node 0 totalpages: 128624
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 972 pages used for memmap
[ 0.000000] Normal zone: 123556 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F6C40 checksum 0
[ 0.000000] ACPI: RSDP 000F6C40, 0014 (r0 TOSQCI)
[ 0.000000] ACPI: RSDT 1F67EFB9, 0044 (r1 TOSQCI RSDT 6040000 LTP 0)
[ 0.000000] ACPI: FACP 1F683E8A, 0074 (r1 TOSQCI ALVISO 6040000 LOHR 5F)
[ 0.000000] ACPI: DSDT 1F67F833, 4657 (r1 TOSQCI ALVISO 6040000 MSFT 100000E)
[ 0.000000] ACPI: FACS 1F694FC0, 0040
[ 0.000000] ACPI: APIC 1F683EFE, 0066 (r1 TOSQCI ALVISO 6040000 LOHR 5F)
[ 0.000000] ACPI: HPET 1F683F64, 0038 (r1 TOSQCI ALVISO 6040000 LOHR 5F)
[ 0.000000] ACPI: MCFG 1F683F9C, 003C (r1 TOSQCI ALVISO 6040000 LOHR 5F)
[ 0.000000] ACPI: BOOT 1F683FD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP 1)
[ 0.000000] ACPI: SSDT 1F67F3EE, 0235 (r1 PmRef Cpu0Ist 3000 INTL 20030224)
[ 0.000000] ACPI: SSDT 1F67F216, 01D8 (r1 PmRef Cpu0Cst 3001 INTL 20030224)
[ 0.000000] ACPI: SSDT 1F67EFFD, 0219 (r1 PmRef CpuPm 3000 INTL 20030224)
[ 0.000000] ACPI: DMI detected: Toshiba
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:13 APIC version 20
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec20000] gsi_base[24])
[ 0.000000] IOAPIC[1]: apic_id 2, version 255, address 0xfec20000, GSI 24-279
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 2 I/O APICs
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0x0 is invalid
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000e0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000e0000 - 00000000000e4000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000e4000 - 00000000000e8000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000e8000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 127620
[ 0.000000] Kernel command line: root=UUID=25adaaae-d988-457b-a695-084e420e41d4 ro
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] mapped IOAPIC to ffff9000 (fec20000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 1729.582 MHz processor.
[ 7.631522] Console: colour VGA+ 80x25
[ 7.631526] console [tty0] enabled
[ 7.635540] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 7.635810] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 7.646983] Memory: 497924k/514496k available (2177k kernel code, 15896k reserved, 1006k data, 368k init, 0k highmem)
[ 7.647076] virtual kernel memory layout:
[ 7.647077] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 7.647078] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 7.647080] vmalloc : 0xe0000000 - 0xff7fe000 ( 503 MB)
[ 7.647081] lowmem : 0xc0000000 - 0xdf670000 ( 502 MB)
[ 7.647082] .init : 0xc0421000 - 0xc047d000 ( 368 kB)
[ 7.647083] .data : 0xc0320434 - 0xc041bdc4 (1006 kB)
[ 7.647085] .text : 0xc0100000 - 0xc0320434 (2177 kB)
[ 7.647541] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 7.647687] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 7.727782] Calibrating delay using timer specific routine.. 3462.90 BogoMIPS (lpj=6925808)
[ 7.727917] Security Framework initialized
[ 7.727977] SELinux: Disabled at boot.
[ 7.728045] AppArmor: AppArmor initialized
[ 7.728104] Failure registering capabilities with primary security module.
[ 7.728172] Mount-cache hash table entries: 512
[ 7.728345] Initializing cgroup subsys ns
[ 7.728406] Initializing cgroup subsys cpuacct
[ 7.728470] CPU: After generic identify, caps: afe9fbff 00000000 00000000 00000000 00000180 00000000 00000000 00000000
[ 7.728481] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 7.728568] CPU: L2 cache: 2048K
[ 7.728622] CPU: After all inits, caps: afe9fbff 00000000 00000000 00002040 00000180 00000000 00000000 00000000
[ 7.728631] Compat vDSO mapped to ffffe000.
[ 7.728695] Checking 'hlt' instruction... OK.
[ 7.744204] SMP alternatives: switching to UP code
[ 7.746102] Freeing SMP alternatives: 11k freed
[ 7.746259] Early unpacking initramfs... done
[ 8.094378] ACPI: Core revision 20070126
[ 8.094492] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 8.120837] CPU0: Intel(R) Pentium(R) M processor 1.73GHz stepping 08
[ 8.120979] Total of 1 processors activated (3462.90 BogoMIPS).
[ 8.123010] ENABLING IO-APIC IRQs
[ 8.123269] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 8.267800] Brought up 1 CPUs
[ 8.267893] CPU0 attaching sched-domain:
[ 8.267896] domain 0: span 01
[ 8.267898] groups: 01
[ 8.268055] net_namespace: 64 bytes
[ 8.268116] Booting paravirtualized kernel on bare hardware
[ 8.268620] Time: 9:15:40 Date: 06/16/08
[ 8.268698] NET: Registered protocol family 16
[ 8.268937] EISA bus registered
[ 8.269014] ACPI: bus type pci registered
[ 8.294491] PCI: PCI BIOS revision 2.10 entry at 0xfd7be, last bus=7
[ 8.294551] PCI: Using configuration type 1
[ 8.294614] Setting up standard PCI resources
[ 8.302069] ACPI: EC: Look up EC in DSDT
[ 8.303281] ACPI: Interpreter enabled
[ 8.303337] ACPI: (supports S0 S3 S4 S5)
[ 8.303525] ACPI: Using IOAPIC for interrupt routing
[ 8.370723] ACPI: EC: GPE = 0x1d, I/O: command/status = 0x66, data = 0x62
[ 8.370785] ACPI: EC: driver started in poll mode
[ 8.370881] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 8.371619] Force enabled HPET at base address 0xfed00000
[ 8.371627] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[ 8.371690] PCI quirk: region 1180-11bf claimed by ICH6 GPIO
[ 8.372457] PCI: Transparent bridge - 0000:00:1e.0
[ 8.372597] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 8.372903] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 8.375197] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 8.375698] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 8.376247] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 8.376794] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 8.377295] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 8.377839] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 8.378419] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 8.378996] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 8.379527] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 8.379614] pnp: PnP ACPI init
[ 8.379672] ACPI: bus type pnp registered
[ 8.380818] pnp: PnP ACPI: found 8 devices
[ 8.380874] ACPI: ACPI bus type pnp unregistered
[ 8.380931] PnPBIOS: Disabled by ACPI PNP
[ 8.381192] PCI: Using ACPI for IRQ routing
[ 8.381248] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 8.381330] PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.0
[ 8.381391] PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.0
[ 8.381452] PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.0
[ 8.381514] PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.1
[ 8.381575] PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.1
[ 8.381636] PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.1
[ 8.381697] PCI: Cannot allocate resource region 7 of bridge 0000:00:1c.2
[ 8.381759] PCI: Cannot allocate resource region 8 of bridge 0000:00:1c.2
[ 8.381820] PCI: Cannot allocate resource region 9 of bridge 0000:00:1c.2
[ 8.411759] NET: Registered protocol family 8
[ 8.411815] NET: Registered protocol family 20
[ 8.412027] hpet clockevent registered
[ 8.412033] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 8.412212] hpet0: 3 64-bit timers, 14318180 Hz
[ 8.413302] AppArmor: AppArmor Filesystem Enabled
[ 8.415752] Time: tsc clocksource has been installed.
[ 8.423788] system 00:01: iomem range 0xe0000000-0xefffffff could not be reserved
[ 8.423867] system 00:01: iomem range 0xf0000000-0xf0003fff could not be reserved
[ 8.423946] system 00:01: iomem range 0xf0004000-0xf0004fff could not be reserved
[ 8.424024] system 00:01: iomem range 0xf0005000-0xf0005fff could not be reserved
[ 8.424103] system 00:01: iomem range 0xf0008000-0xf000bfff could not be reserved
[ 8.424182] system 00:01: iomem range 0xfed20000-0xfed3ffff could not be reserved
[ 8.424261] system 00:01: iomem range 0xfed45000-0xfed8ffff could not be reserved
[ 8.424343] system 00:04: ioport range 0x680-0x6ff has been reserved
[ 8.424403] system 00:04: ioport range 0x800-0x80f has been reserved
[ 8.424464] system 00:04: ioport range 0x1000-0x107f has been reserved
[ 8.424526] system 00:04: ioport range 0x1180-0x11bf has been reserved
[ 8.424587] system 00:04: ioport range 0x1600-0x167f has been reserved
[ 8.455048] PCI: Bridge: 0000:00:1c.0
[ 8.456096] IO window: disabled.
[ 8.456153] MEM window: disabled.
[ 8.456209] PREFETCH window: disabled.
[ 8.456268] PCI: Bridge: 0000:00:1c.1
[ 8.456322] IO window: disabled.
[ 8.456379] MEM window: disabled.
[ 8.456435] PREFETCH window: disabled.
[ 8.456493] PCI: Bridge: 0000:00:1c.2
[ 8.456547] IO window: disabled.
[ 8.456604] MEM window: disabled.
[ 8.456660] PREFETCH window: disabled.
[ 8.456721] PCI: Bus 7, cardbus bridge: 0000:06:01.0
[ 8.456778] IO window: 00003400-000034ff
[ 8.456837] IO window: 00003800-000038ff
[ 8.456896] PREFETCH window: 34000000-37ffffff
[ 8.456956] MEM window: 38000000-3bffffff
[ 8.457014] PCI: Bridge: 0000:00:1e.0
[ 8.457070] IO window: 3000-3fff
[ 8.457128] MEM window: b0100000-b01fffff
[ 8.457186] PREFETCH window: disabled.
[ 8.457265] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 16
[ 8.457379] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 8.457400] ACPI: PCI Interrupt 0000:00:1c.1
-> GSI 16 (level, low) -> IRQ 17
[ 8.457513] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 8.457534] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 8.457646] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 8.457659] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 8.457675] ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 8.457794] NET: Registered protocol family 2
[ 8.495807] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 8.496051] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 8.496221] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 8.496374] TCP: Hash tables configured (established 16384 bind 16384)
[ 8.496435] TCP reno registered
[ 8.507857] checking if image is initramfs... it is
[ 8.915734] Switched to high resolution mode on CPU 0
[ 9.198967] Freeing initrd memory: 7320k freed
[ 9.236953] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 9.241153] Simple Boot Flag at 0x36 set to 0x1
[ 9.243350] audit: initializing netlink socket (disabled)
[ 9.243424] audit(1213607740.468:1): initialized
[ 9.245464] VFS: Disk quotas dquot_6.5.1
[ 9.245595] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 9.245797] io scheduler noop registered
[ 9.245852] io scheduler anticipatory registered
[ 9.245909] io scheduler deadline registered
[ 9.245975] io scheduler cfq registered (default)
[ 9.246042] Boot video device is 0000:00:02.0
[ 9.246204] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 9.246256] assign_interrupt_mode Found MSI capability
[ 9.246359] Allocate Port Service[0000:00:1c.0:pcie00]
[ 9.246402] Allocate Port Service[0000:00:1c.0:pcie02]
[ 9.246495] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 9.246546] assign_interrupt_mode Found MSI capability
[ 9.246644] Allocate Port Service[0000:00:1c.1:pcie00]
[ 9.246675] Allocate Port Service[0000:00:1c.1:pcie02]
[ 9.246767] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 9.246818] assign_interrupt_mode Found MSI capability
[ 9.246915] Allocate Port Service[0000:00:1c.2:pcie00]
[ 9.246948] Allocate Port Service[0000:00:1c.2:pcie02]
[ 9.247199] isapnp: Scanning for PnP cards...
[ 9.601488] isapnp: No Plug & Play device found
[ 9.627646] Real Time Clock Driver v1.12ac
[ 9.627808] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 9.628442] ACPI: PCI Interrupt 0000:00:1e.3 -> GSI 20 (level, low) -> IRQ 19
[ 9.628558] ACPI: PCI interrupt for device 0000:00:1e.3 disabled
[ 9.629228] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 9.629376] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 9.629545] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 9.632681] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 9.632742] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 9.643628] mice: PS/2 mouse device common for all mice
[ 9.643799] EISA: Probing bus 0 at eisa.0
[ 9.643859] Cannot allocate resource for EISA slot 1
[ 9.643917] Cannot allocate resource for EISA slot 2
[ 9.643975] Cannot allocate resource for EISA slot 3
[ 9.644050] EISA: Detected 0 cards.
[ 9.644105] cpuidle: using governor ladder
[ 9.644161] cpuidle: using governor menu
[ 9.644309] NET: Registered protocol family 1
[ 9.644389] Using IPI No-Shortcut mode
[ 9.644474] registered taskstats version 1
[ 9.644632] Magic number: 12:872:272
[ 9.644697] hash matches device ttyy0
[ 9.644837] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 9.644896] EDD information not available.
[ 9.645144] Freeing unused kernel memory: 368k freed
[ 9.683588] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 9.840091] fuse init (API version 7.9)
[ 9.859282] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[ 9.859508] ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 9.869794] ACPI: Thermal Zone [THRM] (69 C)
[ 10.452106] usbcore: registered new interface driver usbfs
[ 10.452193] usbcore: registered new interface driver hub
[ 10.457634] usbcore: registered new device driver usb
[ 10.470673] USB Universal Host Controller Interface driver v3.0
[ 10.470793] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20
[ 10.470910] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 10.470914] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 10.471309] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 10.471417] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001820
[ 10.471617] usb usb1: configuration #1 chosen from 1 choice
[ 10.471699] hub 1-0:1.0: USB hub found
[ 10.471757] hub 1-0:1.0: 2 ports detected
[ 10.520958] 8139too Fast Ethernet driver 0.9.28
[ 10.575549] ACPI: PCI Interrupt 0000:00:1d.1 -> GSI 19 (level, low) -> IRQ 21
[ 10.575671] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 10.575676] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 10.575754] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 10.575863] uhci_hcd 0000:00:1d.1: irq 21, io base 0x00001840
[ 10.576028] usb usb2: configuration #1 chosen from 1 choice
[ 10.576107] hub 2-0:1.0: USB hub found
[ 10.576165] hub 2-0:1.0: 2 ports detected
[ 10.583666] SCSI subsystem initialized
[ 10.615447] libata version 3.00 loaded.
[ 10.679652] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
[ 10.679779] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 10.679783] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 10.679864] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
[ 10.683852] ehci_hcd 0000:00:1d.7: debug port 1
[ 10.683913] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 10.683921] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xb0040000
[ 10.699431] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 10.699622] usb usb3: configuration #1 chosen from 1 choice
[ 10.699706] hub 3-0:1.0: USB hub found
[ 10.699765] hub 3-0:1.0: 8 ports detected
[ 10.803648] ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 19 (level, low) -> IRQ 21
[ 10.804625] eth0: RealTek RTL8139 at 0x3000, 00:16:36:11:d4:9b, IRQ 21
[ 10.804687] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 10.807198] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 10.811910] ahci 0000:00:1f.2: version 3.0
[ 10.811935] ACPI: PCI Interrupt 0000:00:1f.2 -> GSI 19 (level, low) -> IRQ 21
[ 10.812053] ACPI: PCI interrupt for device 0000:00:1f.2 disabled
[ 10.812115] ahci: probe of 0000:00:1f.2 failed with error -22
[ 10.816406] ata_piix 0000:00:1f.2: version 2.12
[ 10.816411] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ]
[ 10.971417] ACPI: PCI Interrupt 0000:00:1f.2 -> GSI 19 (level, low) -> IRQ 21
[ 10.971569] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 10.972259] scsi0 : ata_piix
[ 10.972746] scsi1 : ata_piix
[ 10.972915] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x18b0 irq 14
[ 10.972978] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18b8 irq 15
[ 11.135729] ata1.00: ATA-6: TOSHIBA MK6032GSX, AS311G, max UDMA/100
[ 11.135797] ata1.00: 117210240 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 11.143727] ata1.00: configured for UDMA/100
[ 11.411323] Clocksource tsc unstable (delta = -35570543483 ns)
[ 11.415342] Time: hpet clocksource has been installed.
[ 11.417152] ata2.00: ATAPI: MATSHITADVD-RAM UJ-841S, 1.50, max UDMA/33
[ 11.464987] ata2.00: configured for UDMA/33
[ 11.465883] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK6032GS AS31 PQ: 0 ANSI: 5
[ 11.468861] scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-841S 1.50 PQ: 0 ANSI: 5
[ 11.501336] Driver 'sd' needs updating - please use bus_type methods
[ 11.501469] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[ 11.501541] sd 0:0:0:0: [sda] Write Protect is off
[ 11.501598] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 11.501613] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.501736] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[ 11.501805] sd 0:0:0:0: [sda] Write Protect is off
[ 11.501862] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 11.501877] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 11.501960] sda:Driver 'sr' needs updating - please use bus_type methods
[ 11.518410] sda1 sda2
[ 11.519388] sd 0:0:0:0: [sda] Attached SCSI disk
[ 11.524908] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 11.524983] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 11.530750] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 11.530830] Uniform CD-ROM driver Revision: 3.20
[ 11.530927] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 11.608092] Attempting manual resume
[ 11.608148] swsusp: Resume From Partition 8:5
[ 11.608150] PM: Checking swsusp image.
[ 11.608269] PM: Resume from disk failed.
[ 11.622834] kjournald starting. Commit interval 5 seconds
[ 11.622904] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.836396] Linux agpgart interface v0.102
[ 13.928382] agpgart: Detected an Intel 915GM Chipset.
[ 13.928950] agpgart: Detected 7932K stolen memory.
[ 14.008314] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 14.068337] agpgart: AGP aperture is 256M @ 0xc0000000
[ 14.068505] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.444378] input: Power Button (FF) as /devices/virtual/input/input2
[ 14.460213] ACPI: Power Button (FF) [PWRF]
[ 14.460385] input: Lid Switch as /devices/virtual/input/input3
[ 14.464685] ACPI: Lid Switch [liD]
[ 14.465247] input: Power Button (CM) as /devices/virtual/input/input4
[ 14.476197] ACPI: Power Button (CM) [PWRB]
[ 14.512300] ACPI: AC Adapter [ACAD] (off-line)
[ 15.168089] iTCO_vendor_support: vendor-support=0
[ 15.232326] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[ 15.244143] iTCO_wdt: Found a ICH6-M TCO device (Version=2, TCOBASE=0x1060)
[ 15.244253] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 15.568020] intel_rng: FWH not detected
[ 15.640145] ACPI: Battery Slot [BAT1] (battery present)
[ 15.640811] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5
[ 15.655994] ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no)
[ 16.356021] ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 17 (level, low) -> IRQ 16
[ 16.356156] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 16.675806] intel8x0_measure_ac97_clock: measured 54102 usecs
[ 16.675872] intel8x0: clocking to 48000
[ 16.751928] Yenta: CardBus bridge found at 0000:06:01.0 [1179:ff31]
[ 16.752028] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 16.752087] Yenta: Routing CardBus interrupts to PCI
[ 16.752149] Yenta TI: socket 0000:06:01.0, mfunc 0x015c1d22, devctl 0x44
[ 16.774689] ieee80211_crypt: registered algorithm 'NULL'
[ 16.813012] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 16.813079] ieee80211: Copyright (C) 2004-2005 Intel Corporation
[ 16.863899] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 16.908776] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[ 16.908860] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[ 16.984574] Yenta: ISA IRQ mask 0x0cf8, PCI irq 17
[ 16.984640] Socket status: 30000007
[ 16.984695] Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #08
[ 16.984776] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff
[ 16.984836] cs: IO port probe 0x3000-0x3fff: clean.
[ 16.985165] pcmcia: parent PCI bridge Memory window: 0xb0100000 - 0xb01fffff
[ 17.027812] ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 17 (level, low) -> IRQ 16
[ 17.060264] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 17.970904] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04713/0x0
[ 17.970994] synaptics: Toshiba Satellite L20 detected, limiting rate to 40pps.
[ 18.006082] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[ 18.634764] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
[ 18.657879] cs: IO port probe 0x100-0x3af: clean.
[ 18.659721] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[ 18.660591] cs: IO port probe 0x820-0x8ff: clean.
[ 18.661272] cs: IO port probe 0xc00-0xcf7: clean.
[ 18.662111] cs: IO port probe 0xa00-0xaff: clean.
[ 18.786974] lp: driver loaded but no devices found
[ 18.831418] NET: Registered protocol family 17
[ 18.988395] Adding 1477940k swap on /dev/sda5. Priority:-1 extents:1 across:1477940k
[ 19.031121] EXT3 FS on sda1, internal journal
[ 19.399985] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 43.840774] Marking TSC unstable due to: cpufreq changes.
[ 26.947588] No dock devices found.
[ 21.003398] apm: BIOS not found.
[ 22.083852] [drm] Initialized drm 1.1.0 20060810
[ 22.103476] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 17
[ 22.103484] PCI: Setting latency timer of device 0000:00:02.0 to 64
[ 22.103549] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 22.304593] eth0: link down
[ 69.231494] NET: Registered protocol family 10
[ 69.232216] lo: Disabled Privacy Extensions
[ 69.233169] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 36.009553] eth1: no IPv6 routers present
[ 98.695817] eth1: no IPv6 routers present
giuseppe@giuseppe-laptop:~$