Ubuntu cli e installazione audio
Inviato: martedì 8 luglio 2008, 15:39
Ciao, mi se è rotto il computer principale e ho dovuto risvegliare il mio vecchio pc.
Poiche' ubuntu è un po' pesantuccio per il mio 700mhz, ho deciso di eseguire una installazione minimale con ubuntu netinst.
dopo aver installato la sola command line, ho deciso di installare come interfaccia grafica lxde e devo dire mi sto' trovando molto bene... un computer molto reattivo anche se con soli 256mb di ram.
pero' ho notato che l'audio nn funziona!!! pensavo bastasse installare alsa-base e alsa-utils, ma l'audio continua a nn sentirsi...
il kernel che ho installato e' quello generico ed ho una realtek ac97... una scheda audio integrata!
lspci mi restituisce questo:
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP]
00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
00:04.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10)
00:04.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10)
00:04.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10)
00:04.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
00:04.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 20)
00:0a.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
00:0b.0 Parallel controller: Timedia Technology Co Ltd Unknown device 7268 (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 MX 440] (rev a3)
lsmod questo:
Module Size Used by
ipv6 267780 8
battery 14212 0
video 19856 0
output 4736 1 video
sbs 15112 0
sbshc 7680 1 sbs
container 5632 0
dock 11280 0
iptable_filter 3840 0
ip_tables 14820 1 iptable_filter
x_tables 16132 1 ip_tables
ac 6916 0
lp 12324 0
loop 18948 0
snd_via82xx 29464 2
gameport 16008 1 snd_via82xx
snd_ac97_codec 101028 1 snd_via82xx
ac97_bus 3072 1 snd_ac97_codec
snd_pcm_oss 42144 0
snd_mixer_oss 17920 1 snd_pcm_oss
snd_pcm 78596 4 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_page_alloc 11400 2 snd_via82xx,snd_pcm
snd_mpu401_uart 9728 1 snd_via82xx
snd_seq_dummy 4868 0
nvidia 4718576 22
snd_seq_oss 35584 0
snd_seq_midi 9376 0
snd_rawmidi 25760 2 snd_mpu401_uart,snd_seq_midi
af_packet 23812 2
snd_seq_midi_event 8320 2 snd_seq_oss,snd_seq_midi
snd_seq 54224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
serio_raw 7940 0
snd_timer 24836 3 snd_pcm,snd_seq
snd_seq_device 9612 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
button 9232 0
snd 56996 14 snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401_uart,snd_seq_dummy,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
i2c_viapro 9876 0
via_agp 11136 1
i2c_core 24832 2 nvidia,i2c_viapro
shpchp 34452 0
soundcore 8800 1 snd
agpgart 34760 2 nvidia,via_agp
pci_hotplug 30880 1 shpchp
parport_pc 36260 2
parport 37832 2 lp,parport_pc
via686a 15244 0
evdev 13056 3
psmouse 40336 0
pcspkr 4224 0
ext3 136712 1
jbd 48404 1 ext3
mbcache 9600 1 ext3
sg 36880 0
sr_mod 17956 0
cdrom 37408 1 sr_mod
sd_mod 30720 3
pata_via 13316 2
ata_generic 8324 0
8139too 27520 0
mii 6400 1 8139too
pata_acpi 8320 0
dmesg questo:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.24-19-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Wed Jun 18 14:43:41 UTC 2008 (Ubuntu 2.6.24-19.34-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000ffec000 (usable)
[ 0.000000] BIOS-e820: 000000000ffec000 - 000000000ffef000 (ACPI data)
[ 0.000000] BIOS-e820: 000000000ffef000 - 000000000ffff000 (reserved)
[ 0.000000] BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 255MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 65516) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 65516
[ 0.000000] HighMem 65516 -> 65516
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 65516
[ 0.000000] On node 0 totalpages: 65516
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 479 pages used for memmap
[ 0.000000] Normal zone: 60941 pages, LIFO batch:15
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F5B70 checksum 0
[ 0.000000] ACPI: RSDP 000F5B70, 0014 (r0 ASUS )
[ 0.000000] ACPI: RSDT 0FFEC000, 002C (r1 ASUS CUV4X_M 30303031 MSFT 31313031)
[ 0.000000] ACPI: FACP 0FFEC080, 0074 (r1 ASUS CUV4X_M 30303031 MSFT 31313031)
[ 0.000000] ACPI: DSDT 0FFEC100, 255B (r1 ASUS CUV4X_M 1000 MSFT 100000B)
[ 0.000000] ACPI: FACS 0FFFF000, 0040
[ 0.000000] ACPI: BOOT 0FFEC040, 0028 (r1 ASUS CUV4X_M 30303031 MSFT 31313031)
[ 0.000000] ACPI: PM-Timer IO Port: 0xe408
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 10000000:efff0000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65005
[ 0.000000] Kernel command line: root=UUID=9168c805-d602-4a64-b9a2-26c80acccf10 ro vga=791
[ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 0.000000] mapped APIC to ffffb000 (0120c000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Detected 701.612 MHz processor.
[ 26.183551] Console: colour dummy device 80x25
[ 26.183566] console [tty0] enabled
[ 26.184370] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 26.185041] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 26.215536] Memory: 248068k/262064k available (2177k kernel code, 13536k reserved, 1006k data, 368k init, 0k highmem)
[ 26.215586] virtual kernel memory layout:
[ 26.215590] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 26.215594] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 26.215598] vmalloc : 0xd0800000 - 0xff7fe000 ( 751 MB)
[ 26.215602] lowmem : 0xc0000000 - 0xcffec000 ( 255 MB)
[ 26.215606] .init : 0xc0421000 - 0xc047d000 ( 368 kB)
[ 26.215610] .data : 0xc0320434 - 0xc041bdc4 (1006 kB)
[ 26.215614] .text : 0xc0100000 - 0xc0320434 (2177 kB)
[ 26.215683] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 26.215800] SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 26.295829] Calibrating delay using timer specific routine.. 1405.06 BogoMIPS (lpj=2810124)
[ 26.295926] Security Framework initialized
[ 26.295959] SELinux: Disabled at boot.
[ 26.296012] AppArmor: AppArmor initialized
[ 26.296031] Failure registering capabilities with primary security module.
[ 26.296066] Mount-cache hash table entries: 512
[ 26.296458] Initializing cgroup subsys ns
[ 26.296497] Initializing cgroup subsys cpuacct
[ 26.296534] CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 26.296566] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 26.296582] CPU: L2 cache: 128K
[ 26.296597] CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 00000000
[ 26.296630] Compat vDSO mapped to ffffe000.
[ 26.296685] Checking 'hlt' instruction... OK.
[ 26.312542] SMP alternatives: switching to UP code
[ 26.316477] Freeing SMP alternatives: 11k freed
[ 26.316944] Early unpacking initramfs... done
[ 27.305099] ACPI: Core revision 20070126
[ 27.305348] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 27.308302] ACPI: setting ELCR to 0200 (from 0c60)
[ 27.308717] CPU0: Intel Celeron (Coppermine) stepping 06
[ 27.308746] SMP motherboard not detected.
[ 27.308759] Local APIC not detected. Using dummy APIC emulation.
[ 27.308935] Brought up 1 CPUs
[ 27.309003] CPU0 attaching sched-domain:
[ 27.309013] domain 0: span 01
[ 27.309018] groups: 01
[ 27.309809] net_namespace: 64 bytes
[ 27.309859] Booting paravirtualized kernel on bare hardware
[ 27.311772] Time: 13:05:24 Date: 07/08/08
[ 27.311915] NET: Registered protocol family 16
[ 27.313066] EISA bus registered
[ 27.313130] ACPI: bus type pci registered
[ 27.315241] PCI: PCI BIOS revision 2.10 entry at 0xf0890, last bus=1
[ 27.315281] PCI: Using configuration type 1
[ 27.315328] Setting up standard PCI resources
[ 27.327928] ACPI: EC: Look up EC in DSDT
[ 27.334451] ACPI: Interpreter enabled
[ 27.334494] ACPI: (supports S0 S1 S4 S5)
[ 27.334547] ACPI: Using PIC for interrupt routing
[ 27.351926] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 27.352653] PCI quirk: region e400-e4ff claimed by vt82c586 ACPI
[ 27.352685] PCI quirk: region e800-e80f claimed by vt82c686 SMB
[ 27.353304] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 27.361761] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 27.362069] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 27.362341] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 27.362613] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 *6 7 9 10 11 12 14 15)
[ 27.363228] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 27.363432] pnp: PnP ACPI init
[ 27.363479] ACPI: bus type pnp registered
[ 27.375034] pnp: PnP ACPI: found 14 devices
[ 27.375076] ACPI: ACPI bus type pnp unregistered
[ 27.375097] PnPBIOS: Disabled by ACPI PNP
[ 27.376579] PCI: Using ACPI for IRQ routing
[ 27.376619] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 27.391544] NET: Registered protocol family 8
[ 27.391576] NET: Registered protocol family 20
[ 27.391950] AppArmor: AppArmor Filesystem Enabled
[ 27.395490] Time: tsc clocksource has been installed.
[ 27.403758] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 27.403789] system 00:00: iomem range 0xf0000-0xfffff could not be reserved
[ 27.403807] system 00:00: iomem range 0x100000-0xfffffff could not be reserved
[ 27.403830] system 00:00: iomem range 0xfffe0000-0xffffffff could not be reserved
[ 27.403871] system 00:02: ioport range 0x3f0-0x3f1 has been reserved
[ 27.403888] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 27.403924] system 00:03: ioport range 0xe400-0xe47f has been reserved
[ 27.403942] system 00:03: ioport range 0xe800-0xe80f has been reserved
[ 27.436297] PCI: Bridge: 0000:00:01.0
[ 27.436332] IO window: disabled.
[ 27.436349] MEM window: d6000000-d76fffff
[ 27.436363] PREFETCH window: d7700000-e3ffffff
[ 27.436401] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 27.436448] NET: Registered protocol family 2
[ 27.475748] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 27.476535] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 27.476826] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 27.477153] TCP: Hash tables configured (established 8192 bind 8192)
[ 27.477184] TCP reno registered
[ 27.488034] checking if image is initramfs...Switched to high resolution mode on CPU 0
[ 28.281822] it is
[ 29.305583] Freeing initrd memory: 7142k freed
[ 29.306346] Simple Boot Flag at 0x3a set to 0x1
[ 29.308140] audit: initializing netlink socket (disabled)
[ 29.308219] audit(1215522326.096:1): initialized
[ 29.318585] VFS: Disk quotas dquot_6.5.1
[ 29.319683] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 29.320383] io scheduler noop registered
[ 29.320413] io scheduler anticipatory registered
[ 29.320426] io scheduler deadline registered
[ 29.320515] io scheduler cfq registered (default)
[ 29.320569] PCI: VIA PCI bridge detected. Disabling DAC.
[ 29.320586] PCI: Disabling Via external APIC routing
[ 29.320661] Boot video device is 0000:01:00.0
[ 29.322098] isapnp: Scanning for PnP cards...
[ 29.676592] isapnp: No Plug & Play device found
[ 29.926260] Real Time Clock Driver v1.12ac
[ 29.926881] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 29.927294] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 29.928049] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 29.931122] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 29.932499] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 29.936722] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 29.937093] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 29.937657] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 29.938403] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 29.938440] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 29.950979] mice: PS/2 mouse device common for all mice
[ 29.951684] EISA: Probing bus 0 at eisa.0
[ 29.951765] EISA: Detected 0 cards.
[ 29.951781] cpuidle: using governor ladder
[ 29.951793] cpuidle: using governor menu
[ 29.952487] NET: Registered protocol family 1
[ 29.952625] Using IPI No-Shortcut mode
[ 29.952760] registered taskstats version 1
[ 29.953047] Magic number: 0:497:78
[ 29.953327] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 29.953345] EDD information not available.
[ 29.954895] Freeing unused kernel memory: 368k freed
[ 29.977365] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 30.273792] vesafb: framebuffer at 0xd8000000, mapped to 0xd0880000, using 3072k, total 65536k
[ 30.273842] vesafb: mode is 1024x768x16, linelength=2048, pages=1
[ 30.273857] vesafb: protected mode interface info at c000:f6d0
[ 30.273873] vesafb: pmi: set display start = c00cf715, set palette = c00cf79a
[ 30.273888] vesafb: pmi: ports = b4c3 b503 ba03 c003 c103 c403 c503 c603 c703 c803 c903 cc03 ce03 cf03 d003 d103 d203 d303 d403 d503 da03 7103
[ 30.273944] vesafb: scrolling: redraw
[ 30.273958] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 30.274710] Console: switching to colour frame buffer device 128x48
[ 30.311694] fb0: VESA VGA frame buffer device
[ 30.642986] fuse init (API version 7.9)
[ 30.713224] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 30.713679] ACPI: Processor [CPU0] (supports 16 throttling states)
[ 32.023899] SCSI subsystem initialized
[ 32.121847] usbcore: registered new interface driver usbfs
[ 32.122350] usbcore: registered new interface driver hub
[ 32.157741] usbcore: registered new device driver usb
[ 32.437616] USB Universal Host Controller Interface driver v3.0
[ 32.439068] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6
[ 32.439497] PCI: setting IRQ 6 as level-triggered
[ 32.439507] ACPI: PCI Interrupt 0000:00:04.2[D] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6
[ 32.440166] uhci_hcd 0000:00:04.2: UHCI Host Controller
[ 32.441257] uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1
[ 33.090639] irq 6: nobody cared (try booting with the "irqpoll" option)
[ 33.091115] Pid: 1177, comm: modprobe Not tainted 2.6.24-19-generic #1
[ 33.105596] [] __report_bad_irq+0x24/0x80
[ 33.120034] [] note_interrupt+0x27b/0x2c0
[ 33.134490] [] handle_IRQ_event+0x30/0x60
[ 33.148970] [] handle_level_irq+0x91/0xf0
[ 33.163525] [] do_IRQ+0x3b/0x70
[ 33.178034] [] common_interrupt+0x23/0x30
[ 33.192584] [] __do_softirq+0x61/0x110
[ 33.207140] [] do_softirq+0x55/0x60
[ 33.221653] [] irq_exit+0x6d/0x80
[ 33.236022] [] do_IRQ+0x40/0x70
[ 33.250253] [] pci_write+0x34/0x40
[ 33.264454] [] common_interrupt+0x23/0x30
[ 33.278588] [] as_antic_stop+0x3b/0x40
[ 33.292502] [] _spin_unlock_irqrestore+0xd/0x20
[ 33.306256] [] setup_irq+0xce/0x1a0
[ 33.319761] [] usb_hcd_irq+0x0/0x60 [usbcore]
[ 33.333258] [] request_irq+0xa1/0xc0
[ 33.346416] [] usb_add_hcd+0x209/0x5f0 [usbcore]
[ 33.359643] [] usb_hcd_pci_probe+0x1be/0x2d0 [usbcore]
[ 33.372820] [] pci_device_probe+0x56/0x80
[ 33.385871] [] driver_probe_device+0x88/0x190
[ 33.398822] [] kobject_uevent_env+0xf0/0x3d0
[ 33.411646] [] __driver_attach+0x9e/0xa0
[ 33.424441] [] bus_for_each_dev+0x3b/0x60
[ 33.437103] [] driver_attach+0x16/0x20
[ 33.449602] [] __driver_attach+0x0/0xa0
[ 33.462031] [] bus_add_driver+0x8a/0x1e0
[ 33.474427] [] __pci_register_driver+0x56/0x90
[ 33.486829] [] uhci_hcd_init+0x7f/0xaa [uhci_hcd]
[ 33.499241] [] sys_init_module+0x126/0x19c0
[ 33.511529] [] kmem_cache_destroy+0x0/0x160
[ 33.523790] [] syscall_call+0x7/0xb
[ 33.536001] =======================
[ 33.548141] handlers:
[ 33.560184] [] (usb_hcd_irq+0x0/0x60 [usbcore])
[ 33.572619] Disabling IRQ #6
[ 33.584977] uhci_hcd 0000:00:04.2: irq 6, io base 0x0000d400
[ 33.661134] libata version 3.00 loaded.
[ 34.053936] 8139too Fast Ethernet driver 0.9.28
[ 34.503017] floppy0: Unable to grab IRQ6 for the floppy driver
[ 34.952412] usb usb1: configuration #1 chosen from 1 choice
[ 34.965717] hub 1-0:1.0: USB hub found
[ 34.978652] hub 1-0:1.0: 2 ports detected
[ 35.096906] ACPI: PCI Interrupt 0000:00:04.3[D] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6
[ 35.110322] uhci_hcd 0000:00:04.3: UHCI Host Controller
[ 35.123373] uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2
[ 35.136506] uhci_hcd 0000:00:04.3: irq 6, io base 0x0000d000
[ 35.151308] usb usb2: configuration #1 chosen from 1 choice
[ 35.164292] hub 2-0:1.0: USB hub found
[ 35.176843] hub 2-0:1.0: 2 ports detected
[ 35.303123] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
[ 35.315901] PCI: setting IRQ 5 as level-triggered
[ 35.315912] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 35.332866] eth0: RealTek RTL8139 at 0xa800, 00:50:ba:4c:a2:80, IRQ 5
[ 35.346147] eth0: Identified 8139 chip type 'RTL-8139C'
[ 35.367583] pata_via 0000:00:04.1: version 0.3.3
[ 35.372431] scsi0 : pata_via
[ 35.388451] scsi1 : pata_via
[ 35.402748] ata1: PATA max UDMA/66 cmd 0x1f0 ctl 0x3f6 bmdma 0xd800 irq 14
[ 35.416179] ata2: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xd808 irq 15
[ 35.593212] ata1.00: ATA-5: QUANTUM FIREBALLlct15 15, A01.0F00, max UDMA/66
[ 35.606764] ata1.00: 29336832 sectors, multi 16: LBA
[ 35.637088] ata1.00: configured for UDMA/66
[ 35.968511] ata2.00: ATAPI: CREATIVEDVD5240E-1, 1.20, max MWDMA2
[ 36.152414] ata2.00: configured for MWDMA2
[ 36.166474] scsi 0:0:0:0: Direct-Access ATA QUANTUM FIREBALL A01. PQ: 0 ANSI: 5
[ 36.183527] scsi 1:0:0:0: CD-ROM CREATIVE DVD5240E-1 1.20 PQ: 0 ANSI: 5
[ 37.029605] Driver 'sd' needs updating - please use bus_type methods
[ 37.049293] sd 0:0:0:0: [sda] 29336832 512-byte hardware sectors (15020 MB)
[ 37.075301] sd 0:0:0:0: [sda] Write Protect is off
[ 37.089488] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 37.091139] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 37.107342] Driver 'sr' needs updating - please use bus_type methods
[ 37.122356] sd 0:0:0:0: [sda] 29336832 512-byte hardware sectors (15020 MB)
[ 37.141651] sd 0:0:0:0: [sda] Write Protect is off
[ 37.156416] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 37.158152] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 37.173344] sda:ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 37.214178] ata1.00: BMDMA stat 0x24
[ 37.229314] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 37.229319] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 37.260412] ata1.00: status: { DRDY ERR }
[ 37.275918] ata1.00: error: { ICRC ABRT }
[ 37.291341] ata1: soft resetting link
[ 37.484133] ata1.00: configured for UDMA/66
[ 37.499607] ata1: EH complete
[ 37.528367] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 37.544044] ata1.00: BMDMA stat 0x24
[ 37.559374] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 37.559379] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 37.590585] ata1.00: status: { DRDY ERR }
[ 37.606078] ata1.00: error: { ICRC ABRT }
[ 37.621462] ata1: soft resetting link
[ 37.816014] ata1.00: configured for UDMA/66
[ 37.831279] ata1: EH complete
[ 37.857676] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 37.872948] ata1.00: BMDMA stat 0x24
[ 37.887716] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 37.887721] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 37.917874] ata1.00: status: { DRDY ERR }
[ 37.932867] ata1.00: error: { ICRC ABRT }
[ 37.947769] ata1: soft resetting link
[ 38.139898] ata1.00: configured for UDMA/66
[ 38.154886] ata1: EH complete
[ 38.173284] ata1.00: limiting speed to UDMA/44:PIO4
[ 38.187869] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 38.202375] ata1.00: BMDMA stat 0x24
[ 38.216948] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 38.216954] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 38.246718] ata1.00: status: { DRDY ERR }
[ 38.261547] ata1.00: error: { ICRC ABRT }
[ 38.276233] ata1: soft resetting link
[ 38.467766] ata1.00: configured for UDMA/44
[ 38.482443] ata1: EH complete
[ 38.502640] sda1 sda2
[ 38.539091] sd 0:0:0:0: [sda] 29336832 512-byte hardware sectors (15020 MB)
[ 38.553693] sd 0:0:0:0: [sda] Write Protect is off
[ 38.567829] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 38.568201] sd 0:0:0:0: [sda] Attached SCSI disk
[ 38.591380] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 38.609076] sd 0:0:0:0: [sda] 29336832 512-byte hardware sectors (15020 MB)
[ 38.623698] sd 0:0:0:0: [sda] Write Protect is off
[ 38.637637] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 38.639367] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 38.655665] sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
[ 38.669913] Uniform CD-ROM driver Revision: 3.20
[ 38.684084] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 38.709026] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 38.723581] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 39.969037] Attempting manual resume
[ 39.982264] swsusp: Resume From Partition 8:1
[ 39.982270] PM: Checking swsusp image.
[ 39.983229] PM: Resume from disk failed.
[ 40.131006] kjournald starting. Commit interval 5 seconds
[ 40.144682] EXT3-fs: mounted filesystem with ordered data mode.
[ 54.008609] floppy0: Unable to grab IRQ6 for the floppy driver
[ 54.158985] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 54.585008] logips2pp: Detected unknown logitech mouse model 101
[ 55.077712] input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input3
[ 57.188348] via686a 0000:00:04.4: base address not set - upgrade BIOS or use force_addr=0xaddr
[ 57.573614] parport_pc: VIA 686A/8231 detected
[ 57.573627] parport_pc: probing current configuration
[ 57.573650] parport_pc: Current parallel port base: 0x378
[ 57.573733] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[ 57.643684] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 57.671661] parport_pc: VIA parallel port: io=0x378, irq=7
[ 57.724385] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
[ 57.738870] PCI: setting IRQ 10 as level-triggered
[ 57.738880] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 57.753546] PCI parallel port detected: 1409:7268, I/O at 0xa400(0xa000)
[ 57.753592] parport1: PC-style at 0xa400 (0xa000) [PCSPP,TRISTATE]
[ 57.799551] Linux agpgart interface v0.102
[ 58.043677] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 58.151549] agpgart: Detected VIA Apollo Pro 133 chipset
[ 58.175130] agpgart: AGP aperture is 64M @ 0xe4000000
[ 58.200416] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 59.675891] input: Power Button (FF) as /devices/virtual/input/input4
[ 59.718935] ACPI: Power Button (FF) [PWRF]
[ 59.776982] input: Power Button (CM) as /devices/virtual/input/input5
[ 59.826854] ACPI: Power Button (CM) [PWRB]
[ 61.011316] NET: Registered protocol family 17
[ 63.112784] nvidia: module license 'NVIDIA' taints kernel.
[ 64.645867] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 64.661394] PCI: setting IRQ 11 as level-triggered
[ 64.661405] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 64.694318] NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.05 Tue Jan 22 19:36:58 PST 2008
[ 65.522663] ACPI: PCI Interrupt 0000:00:04.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 65.538927] PCI: Setting latency timer of device 0000:00:04.5 to 64
[ 70.180415] loop: module loaded
[ 70.325086] lp0: using parport0 (interrupt-driven).
[ 70.341103] lp1: using parport1 (polling).
[ 71.038310] Adding 530136k swap on /dev/sda1. Priority:-1 extents:1 across:530136k
[ 71.916087] EXT3 FS on sda2, internal journal
[ 73.971861] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 76.119474] No dock devices found.
[ 79.884526] NET: Registered protocol family 10
[ 79.886175] lo: Disabled Privacy Extensions
[ 90.583277] eth0: no IPv6 routers present
[ 135.535436] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 135.536345] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 135.537022] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
Cosa manca per far funzionare questo maledetto audio??? (il volume del master in alsamixer è al max)
Poiche' ubuntu è un po' pesantuccio per il mio 700mhz, ho deciso di eseguire una installazione minimale con ubuntu netinst.
dopo aver installato la sola command line, ho deciso di installare come interfaccia grafica lxde e devo dire mi sto' trovando molto bene... un computer molto reattivo anche se con soli 256mb di ram.
pero' ho notato che l'audio nn funziona!!! pensavo bastasse installare alsa-base e alsa-utils, ma l'audio continua a nn sentirsi...
il kernel che ho installato e' quello generico ed ho una realtek ac97... una scheda audio integrata!
lspci mi restituisce questo:
00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP]
00:04.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
00:04.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10)
00:04.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10)
00:04.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10)
00:04.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
00:04.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 20)
00:0a.0 Ethernet controller: D-Link System Inc RTL8139 Ethernet (rev 10)
00:0b.0 Parallel controller: Timedia Technology Co Ltd Unknown device 7268 (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 MX 440] (rev a3)
lsmod questo:
Module Size Used by
ipv6 267780 8
battery 14212 0
video 19856 0
output 4736 1 video
sbs 15112 0
sbshc 7680 1 sbs
container 5632 0
dock 11280 0
iptable_filter 3840 0
ip_tables 14820 1 iptable_filter
x_tables 16132 1 ip_tables
ac 6916 0
lp 12324 0
loop 18948 0
snd_via82xx 29464 2
gameport 16008 1 snd_via82xx
snd_ac97_codec 101028 1 snd_via82xx
ac97_bus 3072 1 snd_ac97_codec
snd_pcm_oss 42144 0
snd_mixer_oss 17920 1 snd_pcm_oss
snd_pcm 78596 4 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_page_alloc 11400 2 snd_via82xx,snd_pcm
snd_mpu401_uart 9728 1 snd_via82xx
snd_seq_dummy 4868 0
nvidia 4718576 22
snd_seq_oss 35584 0
snd_seq_midi 9376 0
snd_rawmidi 25760 2 snd_mpu401_uart,snd_seq_midi
af_packet 23812 2
snd_seq_midi_event 8320 2 snd_seq_oss,snd_seq_midi
snd_seq 54224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
serio_raw 7940 0
snd_timer 24836 3 snd_pcm,snd_seq
snd_seq_device 9612 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
button 9232 0
snd 56996 14 snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401_uart,snd_seq_dummy,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
i2c_viapro 9876 0
via_agp 11136 1
i2c_core 24832 2 nvidia,i2c_viapro
shpchp 34452 0
soundcore 8800 1 snd
agpgart 34760 2 nvidia,via_agp
pci_hotplug 30880 1 shpchp
parport_pc 36260 2
parport 37832 2 lp,parport_pc
via686a 15244 0
evdev 13056 3
psmouse 40336 0
pcspkr 4224 0
ext3 136712 1
jbd 48404 1 ext3
mbcache 9600 1 ext3
sg 36880 0
sr_mod 17956 0
cdrom 37408 1 sr_mod
sd_mod 30720 3
pata_via 13316 2
ata_generic 8324 0
8139too 27520 0
mii 6400 1 8139too
pata_acpi 8320 0
dmesg questo:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.24-19-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Wed Jun 18 14:43:41 UTC 2008 (Ubuntu 2.6.24-19.34-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000000ffec000 (usable)
[ 0.000000] BIOS-e820: 000000000ffec000 - 000000000ffef000 (ACPI data)
[ 0.000000] BIOS-e820: 000000000ffef000 - 000000000ffff000 (reserved)
[ 0.000000] BIOS-e820: 000000000ffff000 - 0000000010000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 255MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 65516) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 65516
[ 0.000000] HighMem 65516 -> 65516
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 65516
[ 0.000000] On node 0 totalpages: 65516
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 479 pages used for memmap
[ 0.000000] Normal zone: 60941 pages, LIFO batch:15
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F5B70 checksum 0
[ 0.000000] ACPI: RSDP 000F5B70, 0014 (r0 ASUS )
[ 0.000000] ACPI: RSDT 0FFEC000, 002C (r1 ASUS CUV4X_M 30303031 MSFT 31313031)
[ 0.000000] ACPI: FACP 0FFEC080, 0074 (r1 ASUS CUV4X_M 30303031 MSFT 31313031)
[ 0.000000] ACPI: DSDT 0FFEC100, 255B (r1 ASUS CUV4X_M 1000 MSFT 100000B)
[ 0.000000] ACPI: FACS 0FFFF000, 0040
[ 0.000000] ACPI: BOOT 0FFEC040, 0028 (r1 ASUS CUV4X_M 30303031 MSFT 31313031)
[ 0.000000] ACPI: PM-Timer IO Port: 0xe408
[ 0.000000] Allocating PCI resources starting at 20000000 (gap: 10000000:efff0000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65005
[ 0.000000] Kernel command line: root=UUID=9168c805-d602-4a64-b9a2-26c80acccf10 ro vga=791
[ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[ 0.000000] mapped APIC to ffffb000 (0120c000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Detected 701.612 MHz processor.
[ 26.183551] Console: colour dummy device 80x25
[ 26.183566] console [tty0] enabled
[ 26.184370] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 26.185041] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 26.215536] Memory: 248068k/262064k available (2177k kernel code, 13536k reserved, 1006k data, 368k init, 0k highmem)
[ 26.215586] virtual kernel memory layout:
[ 26.215590] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 26.215594] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 26.215598] vmalloc : 0xd0800000 - 0xff7fe000 ( 751 MB)
[ 26.215602] lowmem : 0xc0000000 - 0xcffec000 ( 255 MB)
[ 26.215606] .init : 0xc0421000 - 0xc047d000 ( 368 kB)
[ 26.215610] .data : 0xc0320434 - 0xc041bdc4 (1006 kB)
[ 26.215614] .text : 0xc0100000 - 0xc0320434 (2177 kB)
[ 26.215683] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 26.215800] SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
[ 26.295829] Calibrating delay using timer specific routine.. 1405.06 BogoMIPS (lpj=2810124)
[ 26.295926] Security Framework initialized
[ 26.295959] SELinux: Disabled at boot.
[ 26.296012] AppArmor: AppArmor initialized
[ 26.296031] Failure registering capabilities with primary security module.
[ 26.296066] Mount-cache hash table entries: 512
[ 26.296458] Initializing cgroup subsys ns
[ 26.296497] Initializing cgroup subsys cpuacct
[ 26.296534] CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 26.296566] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 26.296582] CPU: L2 cache: 128K
[ 26.296597] CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 00000000
[ 26.296630] Compat vDSO mapped to ffffe000.
[ 26.296685] Checking 'hlt' instruction... OK.
[ 26.312542] SMP alternatives: switching to UP code
[ 26.316477] Freeing SMP alternatives: 11k freed
[ 26.316944] Early unpacking initramfs... done
[ 27.305099] ACPI: Core revision 20070126
[ 27.305348] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 27.308302] ACPI: setting ELCR to 0200 (from 0c60)
[ 27.308717] CPU0: Intel Celeron (Coppermine) stepping 06
[ 27.308746] SMP motherboard not detected.
[ 27.308759] Local APIC not detected. Using dummy APIC emulation.
[ 27.308935] Brought up 1 CPUs
[ 27.309003] CPU0 attaching sched-domain:
[ 27.309013] domain 0: span 01
[ 27.309018] groups: 01
[ 27.309809] net_namespace: 64 bytes
[ 27.309859] Booting paravirtualized kernel on bare hardware
[ 27.311772] Time: 13:05:24 Date: 07/08/08
[ 27.311915] NET: Registered protocol family 16
[ 27.313066] EISA bus registered
[ 27.313130] ACPI: bus type pci registered
[ 27.315241] PCI: PCI BIOS revision 2.10 entry at 0xf0890, last bus=1
[ 27.315281] PCI: Using configuration type 1
[ 27.315328] Setting up standard PCI resources
[ 27.327928] ACPI: EC: Look up EC in DSDT
[ 27.334451] ACPI: Interpreter enabled
[ 27.334494] ACPI: (supports S0 S1 S4 S5)
[ 27.334547] ACPI: Using PIC for interrupt routing
[ 27.351926] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 27.352653] PCI quirk: region e400-e4ff claimed by vt82c586 ACPI
[ 27.352685] PCI quirk: region e800-e80f claimed by vt82c686 SMB
[ 27.353304] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 27.361761] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[ 27.362069] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[ 27.362341] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[ 27.362613] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 *6 7 9 10 11 12 14 15)
[ 27.363228] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 27.363432] pnp: PnP ACPI init
[ 27.363479] ACPI: bus type pnp registered
[ 27.375034] pnp: PnP ACPI: found 14 devices
[ 27.375076] ACPI: ACPI bus type pnp unregistered
[ 27.375097] PnPBIOS: Disabled by ACPI PNP
[ 27.376579] PCI: Using ACPI for IRQ routing
[ 27.376619] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 27.391544] NET: Registered protocol family 8
[ 27.391576] NET: Registered protocol family 20
[ 27.391950] AppArmor: AppArmor Filesystem Enabled
[ 27.395490] Time: tsc clocksource has been installed.
[ 27.403758] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 27.403789] system 00:00: iomem range 0xf0000-0xfffff could not be reserved
[ 27.403807] system 00:00: iomem range 0x100000-0xfffffff could not be reserved
[ 27.403830] system 00:00: iomem range 0xfffe0000-0xffffffff could not be reserved
[ 27.403871] system 00:02: ioport range 0x3f0-0x3f1 has been reserved
[ 27.403888] system 00:02: ioport range 0x4d0-0x4d1 has been reserved
[ 27.403924] system 00:03: ioport range 0xe400-0xe47f has been reserved
[ 27.403942] system 00:03: ioport range 0xe800-0xe80f has been reserved
[ 27.436297] PCI: Bridge: 0000:00:01.0
[ 27.436332] IO window: disabled.
[ 27.436349] MEM window: d6000000-d76fffff
[ 27.436363] PREFETCH window: d7700000-e3ffffff
[ 27.436401] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 27.436448] NET: Registered protocol family 2
[ 27.475748] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 27.476535] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 27.476826] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 27.477153] TCP: Hash tables configured (established 8192 bind 8192)
[ 27.477184] TCP reno registered
[ 27.488034] checking if image is initramfs...Switched to high resolution mode on CPU 0
[ 28.281822] it is
[ 29.305583] Freeing initrd memory: 7142k freed
[ 29.306346] Simple Boot Flag at 0x3a set to 0x1
[ 29.308140] audit: initializing netlink socket (disabled)
[ 29.308219] audit(1215522326.096:1): initialized
[ 29.318585] VFS: Disk quotas dquot_6.5.1
[ 29.319683] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 29.320383] io scheduler noop registered
[ 29.320413] io scheduler anticipatory registered
[ 29.320426] io scheduler deadline registered
[ 29.320515] io scheduler cfq registered (default)
[ 29.320569] PCI: VIA PCI bridge detected. Disabling DAC.
[ 29.320586] PCI: Disabling Via external APIC routing
[ 29.320661] Boot video device is 0000:01:00.0
[ 29.322098] isapnp: Scanning for PnP cards...
[ 29.676592] isapnp: No Plug & Play device found
[ 29.926260] Real Time Clock Driver v1.12ac
[ 29.926881] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 29.927294] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 29.928049] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 29.931122] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 29.932499] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 29.936722] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 29.937093] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 29.937657] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 29.938403] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 29.938440] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 29.950979] mice: PS/2 mouse device common for all mice
[ 29.951684] EISA: Probing bus 0 at eisa.0
[ 29.951765] EISA: Detected 0 cards.
[ 29.951781] cpuidle: using governor ladder
[ 29.951793] cpuidle: using governor menu
[ 29.952487] NET: Registered protocol family 1
[ 29.952625] Using IPI No-Shortcut mode
[ 29.952760] registered taskstats version 1
[ 29.953047] Magic number: 0:497:78
[ 29.953327] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 29.953345] EDD information not available.
[ 29.954895] Freeing unused kernel memory: 368k freed
[ 29.977365] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 30.273792] vesafb: framebuffer at 0xd8000000, mapped to 0xd0880000, using 3072k, total 65536k
[ 30.273842] vesafb: mode is 1024x768x16, linelength=2048, pages=1
[ 30.273857] vesafb: protected mode interface info at c000:f6d0
[ 30.273873] vesafb: pmi: set display start = c00cf715, set palette = c00cf79a
[ 30.273888] vesafb: pmi: ports = b4c3 b503 ba03 c003 c103 c403 c503 c603 c703 c803 c903 cc03 ce03 cf03 d003 d103 d203 d303 d403 d503 da03 7103
[ 30.273944] vesafb: scrolling: redraw
[ 30.273958] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 30.274710] Console: switching to colour frame buffer device 128x48
[ 30.311694] fb0: VESA VGA frame buffer device
[ 30.642986] fuse init (API version 7.9)
[ 30.713224] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 30.713679] ACPI: Processor [CPU0] (supports 16 throttling states)
[ 32.023899] SCSI subsystem initialized
[ 32.121847] usbcore: registered new interface driver usbfs
[ 32.122350] usbcore: registered new interface driver hub
[ 32.157741] usbcore: registered new device driver usb
[ 32.437616] USB Universal Host Controller Interface driver v3.0
[ 32.439068] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6
[ 32.439497] PCI: setting IRQ 6 as level-triggered
[ 32.439507] ACPI: PCI Interrupt 0000:00:04.2[D] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6
[ 32.440166] uhci_hcd 0000:00:04.2: UHCI Host Controller
[ 32.441257] uhci_hcd 0000:00:04.2: new USB bus registered, assigned bus number 1
[ 33.090639] irq 6: nobody cared (try booting with the "irqpoll" option)
[ 33.091115] Pid: 1177, comm: modprobe Not tainted 2.6.24-19-generic #1
[ 33.105596] [] __report_bad_irq+0x24/0x80
[ 33.120034] [] note_interrupt+0x27b/0x2c0
[ 33.134490] [] handle_IRQ_event+0x30/0x60
[ 33.148970] [] handle_level_irq+0x91/0xf0
[ 33.163525] [] do_IRQ+0x3b/0x70
[ 33.178034] [] common_interrupt+0x23/0x30
[ 33.192584] [] __do_softirq+0x61/0x110
[ 33.207140] [] do_softirq+0x55/0x60
[ 33.221653] [] irq_exit+0x6d/0x80
[ 33.236022] [] do_IRQ+0x40/0x70
[ 33.250253] [] pci_write+0x34/0x40
[ 33.264454] [] common_interrupt+0x23/0x30
[ 33.278588] [] as_antic_stop+0x3b/0x40
[ 33.292502] [] _spin_unlock_irqrestore+0xd/0x20
[ 33.306256] [] setup_irq+0xce/0x1a0
[ 33.319761] [] usb_hcd_irq+0x0/0x60 [usbcore]
[ 33.333258] [] request_irq+0xa1/0xc0
[ 33.346416] [] usb_add_hcd+0x209/0x5f0 [usbcore]
[ 33.359643] [] usb_hcd_pci_probe+0x1be/0x2d0 [usbcore]
[ 33.372820] [] pci_device_probe+0x56/0x80
[ 33.385871] [] driver_probe_device+0x88/0x190
[ 33.398822] [] kobject_uevent_env+0xf0/0x3d0
[ 33.411646] [] __driver_attach+0x9e/0xa0
[ 33.424441] [] bus_for_each_dev+0x3b/0x60
[ 33.437103] [] driver_attach+0x16/0x20
[ 33.449602] [] __driver_attach+0x0/0xa0
[ 33.462031] [] bus_add_driver+0x8a/0x1e0
[ 33.474427] [] __pci_register_driver+0x56/0x90
[ 33.486829] [] uhci_hcd_init+0x7f/0xaa [uhci_hcd]
[ 33.499241] [] sys_init_module+0x126/0x19c0
[ 33.511529] [] kmem_cache_destroy+0x0/0x160
[ 33.523790] [] syscall_call+0x7/0xb
[ 33.536001] =======================
[ 33.548141] handlers:
[ 33.560184] [] (usb_hcd_irq+0x0/0x60 [usbcore])
[ 33.572619] Disabling IRQ #6
[ 33.584977] uhci_hcd 0000:00:04.2: irq 6, io base 0x0000d400
[ 33.661134] libata version 3.00 loaded.
[ 34.053936] 8139too Fast Ethernet driver 0.9.28
[ 34.503017] floppy0: Unable to grab IRQ6 for the floppy driver
[ 34.952412] usb usb1: configuration #1 chosen from 1 choice
[ 34.965717] hub 1-0:1.0: USB hub found
[ 34.978652] hub 1-0:1.0: 2 ports detected
[ 35.096906] ACPI: PCI Interrupt 0000:00:04.3[D] -> Link [LNKD] -> GSI 6 (level, low) -> IRQ 6
[ 35.110322] uhci_hcd 0000:00:04.3: UHCI Host Controller
[ 35.123373] uhci_hcd 0000:00:04.3: new USB bus registered, assigned bus number 2
[ 35.136506] uhci_hcd 0000:00:04.3: irq 6, io base 0x0000d000
[ 35.151308] usb usb2: configuration #1 chosen from 1 choice
[ 35.164292] hub 2-0:1.0: USB hub found
[ 35.176843] hub 2-0:1.0: 2 ports detected
[ 35.303123] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
[ 35.315901] PCI: setting IRQ 5 as level-triggered
[ 35.315912] ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 35.332866] eth0: RealTek RTL8139 at 0xa800, 00:50:ba:4c:a2:80, IRQ 5
[ 35.346147] eth0: Identified 8139 chip type 'RTL-8139C'
[ 35.367583] pata_via 0000:00:04.1: version 0.3.3
[ 35.372431] scsi0 : pata_via
[ 35.388451] scsi1 : pata_via
[ 35.402748] ata1: PATA max UDMA/66 cmd 0x1f0 ctl 0x3f6 bmdma 0xd800 irq 14
[ 35.416179] ata2: PATA max UDMA/66 cmd 0x170 ctl 0x376 bmdma 0xd808 irq 15
[ 35.593212] ata1.00: ATA-5: QUANTUM FIREBALLlct15 15, A01.0F00, max UDMA/66
[ 35.606764] ata1.00: 29336832 sectors, multi 16: LBA
[ 35.637088] ata1.00: configured for UDMA/66
[ 35.968511] ata2.00: ATAPI: CREATIVEDVD5240E-1, 1.20, max MWDMA2
[ 36.152414] ata2.00: configured for MWDMA2
[ 36.166474] scsi 0:0:0:0: Direct-Access ATA QUANTUM FIREBALL A01. PQ: 0 ANSI: 5
[ 36.183527] scsi 1:0:0:0: CD-ROM CREATIVE DVD5240E-1 1.20 PQ: 0 ANSI: 5
[ 37.029605] Driver 'sd' needs updating - please use bus_type methods
[ 37.049293] sd 0:0:0:0: [sda] 29336832 512-byte hardware sectors (15020 MB)
[ 37.075301] sd 0:0:0:0: [sda] Write Protect is off
[ 37.089488] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 37.091139] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 37.107342] Driver 'sr' needs updating - please use bus_type methods
[ 37.122356] sd 0:0:0:0: [sda] 29336832 512-byte hardware sectors (15020 MB)
[ 37.141651] sd 0:0:0:0: [sda] Write Protect is off
[ 37.156416] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 37.158152] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 37.173344] sda:ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 37.214178] ata1.00: BMDMA stat 0x24
[ 37.229314] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 37.229319] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 37.260412] ata1.00: status: { DRDY ERR }
[ 37.275918] ata1.00: error: { ICRC ABRT }
[ 37.291341] ata1: soft resetting link
[ 37.484133] ata1.00: configured for UDMA/66
[ 37.499607] ata1: EH complete
[ 37.528367] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 37.544044] ata1.00: BMDMA stat 0x24
[ 37.559374] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 37.559379] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 37.590585] ata1.00: status: { DRDY ERR }
[ 37.606078] ata1.00: error: { ICRC ABRT }
[ 37.621462] ata1: soft resetting link
[ 37.816014] ata1.00: configured for UDMA/66
[ 37.831279] ata1: EH complete
[ 37.857676] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 37.872948] ata1.00: BMDMA stat 0x24
[ 37.887716] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 37.887721] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 37.917874] ata1.00: status: { DRDY ERR }
[ 37.932867] ata1.00: error: { ICRC ABRT }
[ 37.947769] ata1: soft resetting link
[ 38.139898] ata1.00: configured for UDMA/66
[ 38.154886] ata1: EH complete
[ 38.173284] ata1.00: limiting speed to UDMA/44:PIO4
[ 38.187869] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2
[ 38.202375] ata1.00: BMDMA stat 0x24
[ 38.216948] ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 38.216954] res 51/84:00:07:00:00/00:00:00:00:00/e0 Emask 0x10 (ATA bus error)
[ 38.246718] ata1.00: status: { DRDY ERR }
[ 38.261547] ata1.00: error: { ICRC ABRT }
[ 38.276233] ata1: soft resetting link
[ 38.467766] ata1.00: configured for UDMA/44
[ 38.482443] ata1: EH complete
[ 38.502640] sda1 sda2
[ 38.539091] sd 0:0:0:0: [sda] 29336832 512-byte hardware sectors (15020 MB)
[ 38.553693] sd 0:0:0:0: [sda] Write Protect is off
[ 38.567829] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 38.568201] sd 0:0:0:0: [sda] Attached SCSI disk
[ 38.591380] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 38.609076] sd 0:0:0:0: [sda] 29336832 512-byte hardware sectors (15020 MB)
[ 38.623698] sd 0:0:0:0: [sda] Write Protect is off
[ 38.637637] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 38.639367] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 38.655665] sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
[ 38.669913] Uniform CD-ROM driver Revision: 3.20
[ 38.684084] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 38.709026] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 38.723581] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 39.969037] Attempting manual resume
[ 39.982264] swsusp: Resume From Partition 8:1
[ 39.982270] PM: Checking swsusp image.
[ 39.983229] PM: Resume from disk failed.
[ 40.131006] kjournald starting. Commit interval 5 seconds
[ 40.144682] EXT3-fs: mounted filesystem with ordered data mode.
[ 54.008609] floppy0: Unable to grab IRQ6 for the floppy driver
[ 54.158985] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 54.585008] logips2pp: Detected unknown logitech mouse model 101
[ 55.077712] input: ImExPS/2 Logitech Explorer Mouse as /devices/platform/i8042/serio1/input/input3
[ 57.188348] via686a 0000:00:04.4: base address not set - upgrade BIOS or use force_addr=0xaddr
[ 57.573614] parport_pc: VIA 686A/8231 detected
[ 57.573627] parport_pc: probing current configuration
[ 57.573650] parport_pc: Current parallel port base: 0x378
[ 57.573733] parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
[ 57.643684] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 57.671661] parport_pc: VIA parallel port: io=0x378, irq=7
[ 57.724385] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
[ 57.738870] PCI: setting IRQ 10 as level-triggered
[ 57.738880] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
[ 57.753546] PCI parallel port detected: 1409:7268, I/O at 0xa400(0xa000)
[ 57.753592] parport1: PC-style at 0xa400 (0xa000) [PCSPP,TRISTATE]
[ 57.799551] Linux agpgart interface v0.102
[ 58.043677] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 58.151549] agpgart: Detected VIA Apollo Pro 133 chipset
[ 58.175130] agpgart: AGP aperture is 64M @ 0xe4000000
[ 58.200416] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 59.675891] input: Power Button (FF) as /devices/virtual/input/input4
[ 59.718935] ACPI: Power Button (FF) [PWRF]
[ 59.776982] input: Power Button (CM) as /devices/virtual/input/input5
[ 59.826854] ACPI: Power Button (CM) [PWRB]
[ 61.011316] NET: Registered protocol family 17
[ 63.112784] nvidia: module license 'NVIDIA' taints kernel.
[ 64.645867] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 64.661394] PCI: setting IRQ 11 as level-triggered
[ 64.661405] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 64.694318] NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.05 Tue Jan 22 19:36:58 PST 2008
[ 65.522663] ACPI: PCI Interrupt 0000:00:04.5[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
[ 65.538927] PCI: Setting latency timer of device 0000:00:04.5 to 64
[ 70.180415] loop: module loaded
[ 70.325086] lp0: using parport0 (interrupt-driven).
[ 70.341103] lp1: using parport1 (polling).
[ 71.038310] Adding 530136k swap on /dev/sda1. Priority:-1 extents:1 across:530136k
[ 71.916087] EXT3 FS on sda2, internal journal
[ 73.971861] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 76.119474] No dock devices found.
[ 79.884526] NET: Registered protocol family 10
[ 79.886175] lo: Disabled Privacy Extensions
[ 90.583277] eth0: no IPv6 routers present
[ 135.535436] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[ 135.536345] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[ 135.537022] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
Cosa manca per far funzionare questo maledetto audio??? (il volume del master in alsamixer è al max)