Pagina 1 di 1
Problema mount automatico periferiche usb
Inviato: mercoledì 23 luglio 2008, 0:12
da roberto71
Salve,
ecco il mio problema,ho installato su un pc Ubuntu Hardy e tutto girava a meraviglia,
tranne un piccolo particolare, l'HD secondario in EXT3 non me lo montava all'avvio...
Fino a questo momento se inserivo una pen usb me la montava in automatico e mi mostrava l'icona sul Desktop...
Per poter far partire all'avvio il disco secondario, ho editato fstab, aggiungendo due righe, una riga per montare il disco secondario e l'altra per montare una cartella condivisa NTFS in rete, il tutto con possibilità di scriverci sopra....
ecco il mio nuovo fstab:
# /etc/fstab: static file system information.
#
# -- This file has been automaticly generated by ntfs-config --
#
#
proc /proc proc defaults 0 0
# Entry for /dev/sda1 :
UUID=c2cd9064-c77f-4544-a78b-f8dda1acd7ae / ext3 relatime,errors=remount-ro 0 1
# Entry for /dev/sda5 :
UUID=75c84f79-9d2a-494f-bed8-2cf06ece96fc none swap sw 0 0
UUID=3c14924a-5ac5-4f97-baa8-a39b79bf0071 /media/Slave ext3 rw,defaults 0 0
/dev/scd1 /media/cdrom0 udf,iso9660 user,noauto,exec,utf8 0 0
/dev/scd0 /media/cdrom1 udf,iso9660 user,noauto,exec,utf8 0 0
/dev/fd0 /media/floppy0 auto rw,user,noauto,exec,utf8 0 0
//192.168.0.3/pippo /media/Meteo cifs credentials=/root/smbpw,umask=000,iocharset=utf8 0 0
Dopo aver fatto questa modifica e aver riavviato il pc, il disco secondario si monta all'avvio ed anche la cartella
condivisa funziona correttamente, ma adesso se collego una pen usb od altro per montarla devo andare in Risorse e solo cliccando sopra l'icona mi monta la penna....
cosa può essere successo...
Grazie a chi mi può dare una mano...
Ciao Roberto.
P.S. Se la sezione non è corretta prego i moderatori di spostarla....grazie...
Re: Problema mount automatico periferiche usb
Inviato: mercoledì 23 luglio 2008, 11:30
da M
Se cancelli quelle due righe, tutto torna a funzionare?
ciao,
Marco
Re: Problema mount automatico periferiche usb
Inviato: mercoledì 23 luglio 2008, 13:23
da roberto71
No purtroppo non cambia niente, a parte non farmi vedere la cartella condivisa in rete e
lasciarmi il disco Slave nel menù Risorse....
Non so più cosa pensare....
Mi viene in mente un altra cosa, ma è corretto che il disco secondario interno venga riconosciuto come sdb1?
Ciao.
Re: Problema mount automatico periferiche usb
Inviato: mercoledì 23 luglio 2008, 16:05
da M
Ok, allora il problema non è di fstab! Che venga nominato sdb1 è corretto, prova a collegare la penna usb e post l'output di dmesg.
ciao,
Marco
Re: Problema mount automatico periferiche usb
Inviato: mercoledì 23 luglio 2008, 23:41
da roberto71
Ciao e grazie di tutto...
ecco il risultato....
[ 29.484415] hub 4-0:1.0: 2 ports detected
[ 29.516133] usb 1-1: new full speed USB device using uhci_hcd and address 2
[ 29.587089] ACPI: PCI Interrupt 0000:00:1d.1 -> GSI 19 (level, low) -> IRQ 21
[ 29.587097] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 29.587099] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 29.587116] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5
[ 29.587138] uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000a400
[ 29.587218] usb usb5: configuration #1 chosen from 1 choice
[ 29.587236] hub 5-0:1.0: USB hub found
[ 29.587240] hub 5-0:1.0: 2 ports detected
[ 29.682340] usb 1-1: configuration #1 chosen from 1 choice
[ 29.691187] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 19
[ 29.691194] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 29.691197] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 29.691214] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6
[ 29.691233] uhci_hcd 0000:00:1d.2: irq 19, io base 0x0000a480
[ 29.691320] usb usb6: configuration #1 chosen from 1 choice
[ 29.691337] hub 6-0:1.0: USB hub found
[ 29.691341] hub 6-0:1.0: 2 ports detected
[ 29.794985] PCI: Enabling device 0000:03:00.1 (0000 -> 0001)
[ 29.794991] ACPI: PCI Interrupt 0000:03:00.1 -> GSI 17 (level, low) -> IRQ 17
[ 29.795019] PCI: Setting latency timer of device 0000:03:00.1 to 64
[ 29.795658] scsi0 : pata_jmicron
[ 29.795873] scsi1 : pata_jmicron
[ 29.796339] ata1: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 17
[ 29.796341] ata2: PATA max UDMA/100 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 17
[ 29.922542] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 30.089511] usb 2-1: configuration #1 chosen from 1 choice
[ 30.295467] ata1.00: ATAPI: TSSTcorpDVD-ROM SH-D162C, TS05, max UDMA/33
[ 30.295488] ata1.01: ATAPI: TSSTcorpCD/DVDW SH-S182D, SB03, max UDMA/33
[ 30.333900] usb 5-2: new low speed USB device using uhci_hcd and address 2
[ 30.482187] ata1.00: configured for UDMA/33
[ 30.508838] usb 5-2: configuration #1 chosen from 1 choice
[ 30.511840] usbcore: registered new interface driver libusual
[ 30.515723] Initializing USB Mass Storage driver...
[ 30.516169] scsi2 : SCSI emulation for USB Mass Storage devices
[ 30.516512] usbcore: registered new interface driver usb-storage
[ 30.516514] USB Mass Storage support registered.
[ 30.516574] usb-storage: device found at 2
[ 30.516576] usb-storage: waiting for device to settle before scanning
[ 30.525201] usbcore: registered new interface driver hiddev
[ 30.542907] input: Logitech USB RECEIVER as /devices/pci0000:00/0000:00:1d.1/usb5/5-2/5-2:1.0/input/input2
[ 30.570567] input,hidraw0: USB HID v1.11 Mouse [Logitech USB RECEIVER] on usb-0000:00:1d.1-2
[ 30.570579] usbcore: registered new interface driver usbhid
[ 30.570583] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 30.654919] ata1.01: configured for UDMA/33
[ 30.821094] scsi 0:0:0:0: CD-ROM TSSTcorp DVD-ROM SH-D162C TS05 PQ: 0 ANSI: 5
[ 30.822078] scsi 0:0:1:0: CD-ROM TSSTcorp CD/DVDW SH-S182D SB03 PQ: 0 ANSI: 5
[ 30.822182] ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 30.823379] ACPI: PCI Interrupt 0000:00:1a.7[C] -> GSI 18 (level, low) -> IRQ 19
[ 30.823386] PCI: Setting latency timer of device 0000:00:1a.7 to 64
[ 30.823388] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 30.823407] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7
[ 30.827315] ehci_hcd 0000:00:1a.7: debug port 1
[ 30.827320] PCI: cache line size of 32 is not supported by device 0000:00:1a.7
[ 30.827324] ehci_hcd 0000:00:1a.7: irq 19, io mem 0xfe7ffc00
[ 30.874801] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[17] MMIO=[febff800-febfffff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 30.882144] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 30.882230] usb usb7: configuration #1 chosen from 1 choice
[ 30.882248] hub 7-0:1.0: USB hub found
[ 30.882252] hub 7-0:1.0: 6 ports detected
[ 30.882708] ACPI: PCI Interrupt 0000:05:03.0[A] -> GSI 19 (level, low) -> IRQ 21
[ 30.934310] ohci1394: fw-host1: OHCI-1394 1.0 (PCI): IRQ=[21] MMIO=[febfe000-febfe7ff] Max Packet=[2048] IR/IT contexts=[8/8]
[ 30.984945] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20
[ 30.984954] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 30.984957] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 30.984979] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8
[ 30.988879] ehci_hcd 0000:00:1d.7: debug port 1
[ 30.988884] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 30.988887] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfe7ff800
[ 31.000859] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 31.000962] usb usb8: configuration #1 chosen from 1 choice
[ 31.000987] hub 8-0:1.0: USB hub found
[ 31.000992] hub 8-0:1.0: 6 ports detected
[ 31.104772] ata_piix 0000:00:1f.2: version 2.12
[ 31.104779] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[ 31.104804] ACPI: PCI Interrupt 0000:00:1f.2 -> GSI 22 (level, low) -> IRQ 22
[ 31.104830] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 31.105431] scsi3 : ata_piix
[ 31.105812] scsi4 : ata_piix
[ 31.106603] ata3: SATA max UDMA/133 cmd 0x9000 ctl 0x8c00 bmdma 0x8480 irq 22
[ 31.106605] ata4: SATA max UDMA/133 cmd 0x8880 ctl 0x8800 bmdma 0x8488 irq 22
[ 31.224495] usb 7-1: new high speed USB device using ehci_hcd and address 2
[ 31.269300] ata3.00: ATA-7: WDC WD740ADFD-00NLR4, 21.07QR4, max UDMA/133
[ 31.269304] ata3.00: 145226112 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 31.285320] ata3.00: configured for UDMA/133
[ 31.358657] usb 7-1: configuration #1 chosen from 1 choice
[ 31.358880] scsi5 : SCSI emulation for USB Mass Storage devices
[ 31.359002] usb-storage: device found at 2
[ 31.359003] usb-storage: waiting for device to settle before scanning
[ 31.450851] scsi 3:0:0:0: Direct-Access ATA WDC WD740ADFD-00 21.0 PQ: 0 ANSI: 5
[ 31.450899] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[ 31.450919] ACPI: PCI Interrupt 0000:00:1f.5 -> GSI 22 (level, low) -> IRQ 22
[ 31.450941] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 31.450981] scsi6 : ata_piix
[ 31.451010] scsi7 : ata_piix
[ 31.451779] ata5: SATA max UDMA/133 cmd 0xa000 ctl 0x9c00 bmdma 0x9480 irq 22
[ 31.451781] ata6: SATA max UDMA/133 cmd 0x9880 ctl 0x9800 bmdma 0x9488 irq 22
[ 31.596933] usb 7-3: new high speed USB device using ehci_hcd and address 3
[ 31.735202] usb 7-3: configuration #1 chosen from 1 choice
[ 31.736433] usb 5-2: USB disconnect, address 2
[ 31.807147] ata6.00: ATA-7: ST3400633AS, 3.AAH, max UDMA/133
[ 31.807151] ata6.00: 781422768 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 31.873696] ata6.00: configured for UDMA/133
[ 31.873805] scsi 7:0:0:0: Direct-Access ATA ST3400633AS 3.AA PQ: 0 ANSI: 5
[ 31.874060] ahci 0000:03:00.0: version 3.0
[ 31.874080] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 31.879507] usb 1-1: USB disconnect, address 2
[ 32.007306] usb 2-1: USB disconnect, address 2
[ 32.151151] ieee1394: Host added: ID:BUS[0-00:1023] GUID[001106000000bb7e]
[ 32.207069] ieee1394: Host added: ID:BUS[1-00:1023] GUID[0011d80001525b4e]
[ 32.734160] usb 5-2: new low speed USB device using uhci_hcd and address 3
[ 32.874942] ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[ 32.874946] ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part
[ 32.874952] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 32.875059] scsi8 : ahci
[ 32.875217] scsi9 : ahci
[ 32.875260] ata7: SATA max UDMA/133 abar m8192@0xfeafe000 port 0xfeafe100 irq 16
[ 32.875263] ata8: SATA max UDMA/133 abar m8192@0xfeafe000 port 0xfeafe180 irq 16
[ 32.908172] usb 5-2: configuration #1 chosen from 1 choice
[ 32.929304] input: Logitech USB RECEIVER as /devices/pci0000:00/0000:00:1d.1/usb5/5-2/5-2:1.0/input/input3
[ 32.950872] input,hidraw0: USB HID v1.11 Mouse [Logitech USB RECEIVER] on usb-0000:00:1d.1-2
[ 33.193429] ata7: SATA link down (SStatus 0 SControl 300)
[ 33.512958] ata8: SATA link down (SStatus 0 SControl 300)
[ 33.522706] Driver 'sd' needs updating - please use bus_type methods
[ 33.523868] sd 3:0:0:0: [sda] 145226112 512-byte hardware sectors (74356 MB)
[ 33.523877] sd 3:0:0:0: [sda] Write Protect is off
[ 33.523879] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 33.523891] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.523925] sd 3:0:0:0: [sda] 145226112 512-byte hardware sectors (74356 MB)
[ 33.523933] sd 3:0:0:0: [sda] Write Protect is off
[ 33.523934] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 33.523955] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.523971] sda:Driver 'sr' needs updating - please use bus_type methods
[ 33.537774] sda1 sda2
[ 33.549918] sd 3:0:0:0: [sda] Attached SCSI disk
[ 33.549964] sd 7:0:0:0: [sdb] 781422768 512-byte hardware sectors (400088 MB)
[ 33.549975] sd 7:0:0:0: [sdb] Write Protect is off
[ 33.549978] sd 7:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 33.549995] sd 7:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.550035] sd 7:0:0:0: [sdb] 781422768 512-byte hardware sectors (400088 MB)
[ 33.550048] sd 7:0:0:0: [sdb] Write Protect is off
[ 33.550051] sd 7:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 33.550075] sd 7:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.550077] sdb:sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[ 33.554438] Uniform CD-ROM driver Revision: 3.20
[ 33.554483] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 33.562653] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 33.562695] sr 0:0:1:0: Attached scsi CD-ROM sr1
[ 33.568447] sdb1
[ 33.568499] sd 7:0:0:0: [sdb] Attached SCSI disk
[ 33.571807] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 33.571821] sr 0:0:1:0: Attached scsi generic sg1 type 5
[ 33.571833] sd 3:0:0:0: Attached scsi generic sg2 type 0
[ 33.571846] sd 7:0:0:0: Attached scsi generic sg3 type 0
[ 33.717777] Attempting manual resume
[ 33.717780] swsusp: Resume From Partition 8:5
[ 33.717781] PM: Checking swsusp image.
[ 33.717899] PM: Resume from disk failed.
[ 33.742037] kjournald starting. Commit interval 5 seconds
[ 33.742046] EXT3-fs: mounted filesystem with ordered data mode.
[ 36.348706] usb-storage: device scan complete
[ 36.349327] scsi 5:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 36.349832] scsi 5:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 36.350331] scsi 5:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 36.350829] scsi 5:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 36.352225] sd 5:0:0:0: [sdc] Attached SCSI removable disk
[ 36.352261] sd 5:0:0:0: Attached scsi generic sg4 type 0
[ 36.353346] sd 5:0:0:1: [sdd] Attached SCSI removable disk
[ 36.353378] sd 5:0:0:1: Attached scsi generic sg5 type 0
[ 36.354467] sd 5:0:0:2: [sde] Attached SCSI removable disk
[ 36.354499] sd 5:0:0:2: Attached scsi generic sg6 type 0
[ 36.355591] sd 5:0:0:3: [sdf] Attached SCSI removable disk
[ 36.355624] sd 5:0:0:3: Attached scsi generic sg7 type 0
Re: Problema mount automatico periferiche usb
Inviato: giovedì 24 luglio 2008, 22:51
da M
Eccolo: sdg: unknown partition table!
Hai provato con un'altra chiavetta usb? Ho il presentimento che ci sia qualcosa che non va in quella che stai usando...
ciao,
Marco
Re: Problema mount automatico periferiche usb
Inviato: venerdì 25 luglio 2008, 7:45
da roberto71
Questo è il risultato con un altra chiavetta...
[ 201.710986] usb 8-6: new high speed USB device using ehci_hcd and address 3
[ 201.843807] usb 8-6: configuration #1 chosen from 1 choice
[ 201.844075] scsi9 : SCSI emulation for USB Mass Storage devices
[ 201.844297] usb-storage: device found at 3
[ 201.844301] usb-storage: waiting for device to settle before scanning
[ 206.839081] usb-storage: device scan complete
[ 206.839507] scsi 9:0:0:0: Direct-Access USB USB 2.0 Flash 5.00 PQ: 0 ANSI: 2
[ 206.848423] sd 9:0:0:0: [sdg] 2052096 512-byte hardware sectors (1051 MB)
[ 206.849046] sd 9:0:0:0: [sdg] Write Protect is off
[ 206.849050] sd 9:0:0:0: [sdg] Mode Sense: 0b 00 00 08
[ 206.849052] sd 9:0:0:0: [sdg] Assuming drive cache: write through
[ 206.851166] sd 9:0:0:0: [sdg] 2052096 512-byte hardware sectors (1051 MB)
[ 206.851791] sd 9:0:0:0: [sdg] Write Protect is off
[ 206.851794] sd 9:0:0:0: [sdg] Mode Sense: 0b 00 00 08
[ 206.851796] sd 9:0:0:0: [sdg] Assuming drive cache: write through
[ 206.851799] sdg: sdg1
[ 206.853075] sd 9:0:0:0: [sdg] Attached SCSI removable disk
[ 206.853120] sd 9:0:0:0: Attached scsi generic sg8 type 0
Il problema, come per la chiave precedente è che invece di montarle automaticamente, me li indica in Risorse e se ci vado sopra
col mouse mi scrive > e cliccandoci mi monta il dispositivo sul desktop...poi posso copiare e eliminare qualsiasi file all'interno della chiavetta....
Dimenticato nel frattempo ho installato su un portatile ubuntu 804 e senza modificare fstab, lui funziona bene, con tutte le chiavette....
Ciao Roberto.
Re: Problema mount automatico periferiche usb
Inviato: venerdì 25 luglio 2008, 10:29
da M
Il tuo userid è presente nel gruppo plugdev?
ciao,
Marco
Re: Problema mount automatico periferiche usb
Inviato: venerdì 25 luglio 2008, 13:48
da roberto71
Ciao io il gruppo plugdev non ce l'ho...
e neanche nel portatile dove funziona tutto....
Ciao.