innanzitutto un saluto a tutta la community da un nuovo utilizzatore di Ubuntu
(ho abbandonato la mia macchina slackware 9 anni fa..).
Ho un problema con la configurazione della mia scheda WIFI in oggetto.
è una pcmicia, e inserendola viene riconosciuta correttamente.
lspci
0000:07:00.0 Network controller: Texas Instruments ACX 100 22Mbps Wireless Interface
dmesg | grep acx
[4294700.937000] acx100: It looks like you've been coaxed into buying a wireless network card
[4294700.937000] acx100: that uses the mysterious ACX100/ACX111 chip from Texas Instruments.
[4294700.937000] acx100: You should better have bought e.g. a PRISM(R) chipset based card,
[4294700.937000] acx100: since that would mean REAL vendor Linux support.
[4294700.937000] acx100: Given this info, it's evident that this driver is still EXPERIMENTAL,
[4294700.937000] acx100: thus your mileage may vary. Reading README file and/or Craig's HOWTO is
[4294700.937000] recommended, visit http://acx100.sf.net in case of further questions/discussion.
[4294700.937000] acx100: Warning: compiled to use 16bit I/O access only (compatibility mode). Set Makefile ACX_IO_WIDTH=32 to use slightly problematic 32bit mode
[4294700.937000] acx_init_module: dev_info is: TI acx_pci
[4294700.937000] acx_init_module: TI acx_pci.o: Ver 0.2.0pre8 driver initialized, waiting for car ds to probe...
[4294700.938000] acx_select_io_register_set: using ACX100 io resource addresses (size: 56)
[4294700.938000] acx_probe_pci: TI acx_pci: Using IRQ 11
[4294700.938000] acx_reset_mac: enable soft reset...
[4294700.938000] acx_reset_mac: disable soft reset and go to init mode...
[4294701.239000] acx_write_fw: firmware written
[4294701.316000] acx_write_fw (firmware): 0, acx_validate_fw: 0
[4294701.341000] acx_reset_dev: boot up eCPU and wait for complete...
[4294701.556000] acx_reset_dev: Received signal that card is ready to be configured
(the eCPU has woken up)[4294701.575000] acx100: allocated net device wlan0, driver compiled against wireless extensions v17 and Linux 2.6.12-10-386
[4294701.575000] ************* acx_init_mac_1 *************
[4294701.670000] acx_write_fw: firmware written
[4294701.671000] acx_write_fw (radio): 0, acx_validate_fw: 0
[4294701.816000] acx100_init_wep: writing WEP options.
[4294701.819000] acx100: form factor 0x01 ((mini-)PCI / CardBus), radio type 0x0d (Maxim), EEPROM version 0x05. Uploaded firmware 'Rev 1.9.8.b' (0x01030505).
[4294701.820000] creating /proc entry driver/acx_wlan0
[4294701.820000] creating /proc entry driver/acx_wlan0_diag
[4294701.820000] creating /proc entry driver/acx_wlan0_eeprom
[4294701.820000] creating /proc entry driver/acx_wlan0_phy
[4294701.820000] acx_probe_pci: TI acx_pci.o: Ver 0.2.0pre8 loaded successfully
[4295073.698000] acx_cmd_join_bssid rates_basic 0003->03, rates_supported 0127->1f
[4295073.708000] BSS_Type = 255
[4295073.708000] JoinBSSID MAC:00:00:00:00:00:00
[4295073.708000] acx_set_status: Setting status = 0 (STOPPED)
[4296063.484000] acx_set_status: Setting status = 0 (STOPPED)
al momento della configurazione inserendo ESSID e WEP non ricevo l'ip dal router.
Ho letto molti tutorial su questa scheda e ho notato che con la vecchia distribuzione
di ubuntu non dava problemi.
ho anche provato con il wrapper ndiswrapper con i file .ini dei driver windows, ma nulla.
ho letto anche di provare con madwifi, ma non ho provato.
Qualcuno di voi è riuscito a far funzionare questa scheda?
io utilizzo Ubuntu 5.10 con kernel 2.6.12-10-386.
grazie
Ma7u
)
