Pagina 1 di 2

problema lettura microsd

Inviato: martedì 17 marzo 2009, 12:42
da dfluisa
Salve ragazzi,

premetto che ho gardato per bene le discussioni già postate che riguardano l'argomento e per un pò ho anche provato a smanettare da sola. :-[
Ma ho visto che la maggior parte riguardano soluzioni che cambiano in base a ciò che viene richiesto di postare dopo prove dal terminale, quindi credo proprio di aver bisogno di voi. :-\

Ho ubuntu 8.10.Inserisco la microsd (nell'adattatore), ma non succede nulla,il sistema proprio non la vede.Come posso fare??

Grazie per l'aiuto.

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 12:56
da dfluisa
non mi può aiutare nessuno???vorrei spostare nel cellullare, ma non avendo il cavetto usb...non so davvero come fare...
>:(

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 12:58
da kapello
Prova a montarla manualmente. Dopo che l'hai inserita fai
sudo fdisk -l
che vediamo se il sistema la riconosce

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 13:06
da dfluisa
ciao!

avevo già provato: era un esperimento provato prima della resa...ma nulla!!!

questo è ciò che ne viene fuori:
Disco /dev/sda: 60.0 GB, 60011642880 byte
255 heads, 63 sectors/track, 7296 cylinders
Units = cilindri of 16065 * 512 = 8225280 bytes
Disk identifier: 0xee8cee8c

Dispositivo Boot      Start        End      Blocks  Id  System
/dev/sda1              1        3364    27021298+  83  Linux
/dev/sda2            3365        7296    31583790    5  Esteso
/dev/sda5            3365        7128    30234298+  83  Linux
/dev/sda6            7129        7296    1349428+  82  Linux swap / Solaris
luisa@PuoDarcy:~$

grazie!

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 13:12
da kapello
Sembra non riconoscerla ... c'è solo l'hd. Prova a toglierla, rimetterla e posta
dmesg

mettilo tra tag code mi raccomando. Però se non la riconosce non so se io riesco ad aiutarti..

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 13:17
da dfluisa
...cioè scusa da terminale devo inviare dmesg...tag code??scusami... :-[

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 13:20
da kapello
a terminale scrivi dmesg invio e poi riporti qui il risultato. Però nel post lo metti tra i tag code (la quarta icona da destra sopra le faccine,  #) in modo da non fare un post lunghissimo!

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 13:22
da dfluisa

Codice: Seleziona tutto

[   18.102991] NET: Registered protocol family 20
[   18.103051] AppArmor: AppArmor Filesystem Enabled
[   18.106976] Time: tsc clocksource has been installed.
[   18.115002] system 00:09: ioport range 0x480-0x48f has been reserved
[   18.115005] system 00:09: ioport range 0x5c0-0x5cf has been reserved
[   18.115014] system 00:0a: ioport range 0x4d0-0x4d1 has been reserved
[   18.115021] system 00:0c: iomem range 0xffc00000-0xffefffff has been reserved
[   18.115026] system 00:0d: ioport range 0x540-0x55f has been reserved
[   18.115029] system 00:0d: ioport range 0x400-0x47f has been reserved
[   18.115032] system 00:0d: ioport range 0x480-0x48f has been reserved
[   18.115035] system 00:0d: ioport range 0x500-0x53f has been reserved
[   18.115038] system 00:0d: ioport range 0x4c0-0x4cf has been reserved
[   18.115041] system 00:0d: iomem range 0xfec00000-0xfec00fff has been reserved
[   18.115045] system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
[   18.115051] system 00:0e: iomem range 0x0-0x9ffff could not be reserved
[   18.115054] system 00:0e: iomem range 0xc0000-0xdffff could not be reserved
[   18.115057] system 00:0e: iomem range 0xe0000-0xfffff could not be reserved
[   18.115060] system 00:0e: iomem range 0x100000-0x1fffffff could not be reserved
[   18.115063] system 00:0e: iomem range 0x0-0x0 could not be reserved
[   18.145433] PCI: Bridge: 0000:00:01.0
[   18.145436]   IO window: d000-dfff
[   18.145440]   MEM window: ff800000-ff8fffff
[   18.145443]   PREFETCH window: ce900000-de9fffff
[   18.145458] PCI: Bus 3, cardbus bridge: 0000:02:01.0
[   18.145460]   IO window: 00001000-000010ff
[   18.145464]   IO window: 00001400-000014ff
[   18.145468]   PREFETCH window: 34000000-37ffffff
[   18.145471]   MEM window: 38000000-3bffffff
[   18.145475] PCI: Bus 7, cardbus bridge: 0000:02:01.1
[   18.145477]   IO window: 00001800-000018ff
[   18.145481]   IO window: 00001c00-00001cff
[   18.145484]   PREFETCH window: 3c000000-3fffffff
[   18.145488]   MEM window: 40000000-43ffffff
[   18.145492] PCI: Bridge: 0000:00:1e.0
[   18.145493]   IO window: disabled.
[   18.145498]   MEM window: ff900000-ff9fffff
[   18.145502]   PREFETCH window: dea00000-deafffff
[   18.145516] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   18.145528] PCI: Enabling device 0000:02:01.0 (0000 -> 0003)
[   18.145811] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 4
[   18.145814] PCI: setting IRQ 4 as level-triggered
[   18.145817] ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
[   18.145825] PCI: Setting latency timer of device 0000:02:01.0 to 64
[   18.146104] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[   18.146107] PCI: setting IRQ 11 as level-triggered
[   18.146110] ACPI: PCI Interrupt 0000:02:01.1[B] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[   18.146116] PCI: Setting latency timer of device 0000:02:01.1 to 64
[   18.146127] NET: Registered protocol family 2
[   18.182926] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[   18.183123] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[   18.183231] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[   18.183343] TCP: Hash tables configured (established 16384 bind 16384)
[   18.183345] TCP reno registered
[   18.194964] checking if image is initramfs... it is
[   18.646711] Switched to high resolution mode on CPU 0
[   18.945345] Freeing initrd memory: 7311k freed
[   18.946019] audit: initializing netlink socket (disabled)
[   18.946039] audit(1237286347.392:1): initialized
[   18.948228] VFS: Disk quotas dquot_6.5.1
[   18.948314] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   18.948469] io scheduler noop registered
[   18.948472] io scheduler anticipatory registered
[   18.948474] io scheduler deadline registered
[   18.948486] io scheduler cfq registered (default)
[   18.948558] Boot video device is 0000:01:00.0
[   18.948863] isapnp: Scanning for PnP cards...
[   19.302169] isapnp: No Plug & Play device found
[   19.330432] Real Time Clock Driver v1.12ac
[   19.330556] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   19.330742] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
[   19.331282] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
[   19.331292] ACPI: PCI interrupt for device 0000:00:1f.6 disabled
[   19.331954] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   19.332032] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[   19.332133] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f12:PS2M] at 0x60,0x64 irq 1,12
[   19.334961] i8042.c: Detected active multiplexing controller, rev 1.1.
[   19.336119] serio: i8042 KBD port at 0x60,0x64 irq 1
[   19.336124] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[   19.336127] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[   19.336129] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[   19.336132] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[   19.345086] mice: PS/2 mouse device common for all mice
[   19.345198] EISA: Probing bus 0 at eisa.0
[   19.345207] Cannot allocate resource for EISA slot 1
[   19.345235] EISA: Detected 0 cards.
[   19.345239] cpuidle: using governor ladder
[   19.345241] cpuidle: using governor menu
[   19.345345] NET: Registered protocol family 1
[   19.345372] Using IPI No-Shortcut mode
[   19.345408] registered taskstats version 1
[   19.345507]   Magic number: 1:450:679
[   19.345613] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[   19.345615] EDD information not available.
[   19.345893] Freeing unused kernel memory: 368k freed
[   19.345922] Write protecting the kernel read-only data: 806k
[   19.380976] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[   20.549851] fuse init (API version 7.9)
[   20.570279] ACPI: Invalid PBLK length [7]
[   20.571099] ACPI: CPU0 (power states: C1[C1] C2[C2])
[   20.579353] ACPI: Thermal Zone [THRM] (58 C)
[   21.226145] usbcore: registered new interface driver usbfs
[   21.226173] usbcore: registered new interface driver hub
[   21.233409] usbcore: registered new device driver usb
[   21.246052] USB Universal Host Controller Interface driver v3.0
[   21.246120] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[   21.246136] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   21.246140] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   21.246518] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   21.246544] uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000e800
[   21.246680] usb usb1: configuration #1 chosen from 1 choice
[   21.246705] hub 1-0:1.0: USB hub found
[   21.246710] hub 1-0:1.0: 2 ports detected
[   21.310696] SCSI subsystem initialized
[   21.350323] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
[   21.350329] PCI: setting IRQ 5 as level-triggered
[   21.350333] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
[   21.350347] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   21.350351] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   21.350377] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   21.350404] uhci_hcd 0000:00:1d.1: irq 5, io base 0x0000e880
[   21.350524] usb usb2: configuration #1 chosen from 1 choice
[   21.350549] hub 2-0:1.0: USB hub found
[   21.350555] hub 2-0:1.0: 2 ports detected
[   21.401786] libata version 3.00 loaded.
[   21.454156] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
[   21.454161] PCI: setting IRQ 10 as level-triggered
[   21.454165] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[   21.454179] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   21.454184] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   21.454210] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   21.454237] uhci_hcd 0000:00:1d.2: irq 10, io base 0x0000ec00
[   21.454351] usb usb3: configuration #1 chosen from 1 choice
[   21.454374] hub 3-0:1.0: USB hub found
[   21.454380] hub 3-0:1.0: 2 ports detected
[   21.558085] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
[   21.558091] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 10 (level, low) -> IRQ 10
[   21.558106] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   21.558110] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   21.558136] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
[   21.562038] ehci_hcd 0000:00:1d.7: debug port 1
[   21.562044] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[   21.562052] ehci_hcd 0000:00:1d.7: irq 10, io mem 0xffaffc00
[   21.577507] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   21.577613] usb usb4: configuration #1 chosen from 1 choice
[   21.577638] hub 4-0:1.0: USB hub found
[   21.577645] hub 4-0:1.0: 6 ports detected
[   21.681547] tg3.c:v3.86 (November 9, 2007)
[   21.681577] ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
[   21.731556] eth0: Tigon3 [partno(BCM95788A50) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:17:31:3f:c9:93
[   21.731563] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1]
[   21.731566] eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
[   21.731587] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[   21.731594] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[   21.731633] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[   21.731646] ACPI: PCI interrupt for device 0000:00:1f.1 disabled
[   21.735667] ACPI: PCI Interrupt 0000:02:01.2[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[   21.788324] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10]  MMIO=[ff9ef800-ff9effff]  Max Packet=[2048]  IR/IT contexts=[4/4]
[   21.799997] ata_piix 0000:00:1f.1: version 2.12
[   21.800011] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
[   21.800048] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[   21.800873] scsi0 : ata_piix
[   21.801341] scsi1 : ata_piix
[   21.802846] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[   21.802849] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[   21.965501] ata1.00: ATA-6: IC25N060ATMR04-0, MO3OAD4A, max UDMA/100
[   21.965506] ata1.00: 117210240 sectors, multi 16: LBA48 
[   21.981336] ata1.00: configured for UDMA/100
[   22.300789] ata2.00: ATAPI: MATSHITAUJ-831D, 1.00, max UDMA/33
[   22.472453] ata2.00: configured for UDMA/33
[   22.472593] scsi 0:0:0:0: Direct-Access     ATA      IC25N060ATMR04-0 MO3O PQ: 0 ANSI: 5
[   22.474626] scsi 1:0:0:0: CD-ROM            MATSHITA UJ-831D          1.00 PQ: 0 ANSI: 5
[   22.487582] Driver 'sd' needs updating - please use bus_type methods
[   22.487669] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[   22.487682] sd 0:0:0:0: [sda] Write Protect is off
[   22.487685] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   22.487701] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   22.487750] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012 MB)
[   22.487760] sd 0:0:0:0: [sda] Write Protect is off
[   22.487763] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[   22.487779] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   22.487782]  sda:<4>Driver 'sr' needs updating - please use bus_type methods
[   22.514811]  sda1 sda2 < sda5 sda6 >
[   22.554215] sd 0:0:0:0: [sda] Attached SCSI disk
[   22.559876] sd 0:0:0:0: Attached scsi generic sg0 type 0
[   22.559896] sr 1:0:0:0: Attached scsi generic sg1 type 5
[   22.565260] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[   22.565264] Uniform CD-ROM driver Revision: 3.20
[   22.565313] sr 1:0:0:0: Attached scsi CD-ROM sr0
[   22.871247] Attempting manual resume
[   22.871251] swsusp: Resume From Partition 8:6
[   22.871253] PM: Checking swsusp image.
[   22.871403] PM: Resume from disk failed.
[   22.914473] kjournald starting.  Commit interval 5 seconds
[   22.914483] EXT3-fs: mounted filesystem with ordered data mode.
[   23.067281] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e018000356eea1]
[   39.392026] input: PC Speaker as /devices/platform/pcspkr/input/input2
[   39.707579] intel_rng: FWH not detected
[   39.736905] Linux agpgart interface v0.102
[   39.792840] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   39.900666] agpgart: Detected an Intel 855PM Chipset.
[   39.914280] agpgart: AGP aperture is 256M @ 0xe0000000
[   40.048469] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   40.100319] iTCO_vendor_support: vendor-support=0
[   40.156243] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
[   40.156331] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x0460)
[   40.156362] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   40.292023] irda_init()
[   40.292045] NET: Registered protocol family 23
[   40.419894] parport_pc 00:08: reported by Plug and Play ACPI
[   40.419993] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[   40.551663] nsc_ircc_pnp_probe() : From PnP, found firbase 0x2F8 ; irq 3 ; dma 1.
[   40.551692] nsc-ircc, chip->init
[   40.551701] nsc-ircc, Found chip at base=0x02e
[   40.551725] nsc-ircc, driver loaded (Dag Brattli)
[   40.551730] nsc_ircc_open(), can't get iobase of 0x2f8
[   40.551757] nsc-ircc, Found chip at base=0x02e
[   40.551780] nsc-ircc, driver loaded (Dag Brattli)
[   40.551782] nsc_ircc_open(), can't get iobase of 0x2f8
[   40.552240] nsc-ircc 00:07: disabled
[   40.703502] input: Power Button (FF) as /devices/virtual/input/input3
[   40.715342] ACPI: Power Button (FF) [PWRF]
[   40.715466] input: Lid Switch as /devices/virtual/input/input4
[   40.715561] ACPI: Lid Switch [LID]
[   40.715625] input: Sleep Button (CM) as /devices/virtual/input/input5
[   40.731302] ACPI: Sleep Button (CM) [SLPB]
[   40.731367] input: Power Button (CM) as /devices/virtual/input/input6
[   40.747279] ACPI: Power Button (CM) [PWRB]
[   40.866050] ACPI: AC Adapter [AC] (on-line)
[   41.255804] ACPI: Battery Slot [BAT0] (battery present)
[   41.255883] ACPI: Battery Slot [BAT1] (battery absent)
[   41.256012] asus-laptop: Asus Laptop Support version 0.42
[   41.256140] asus-laptop:   M6NE model detected
[   41.264849] Registered led device: asus:mail
[   42.177409] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:0f/LNXVIDEO:00/input/input7
[   42.189005] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   42.526723] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[   42.875950] [fglrx] Maximum main memory to use for locked dma buffers: 430 MBytes.
[   42.875994] [fglrx] ASYNCIO init succeed!
[   42.876529] [fglrx] PAT is enabled successfully!
[   42.877550] [fglrx] module loaded - fglrx 8.47.3 [Feb 25 2008] on minor 0
[   42.951820] ieee80211_crypt: registered algorithm 'NULL'
[   42.990011] ieee80211: 802.11 data/management/control stack, git-1.1.13
[   42.990016] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[   43.027737] Yenta: CardBus bridge found at 0000:02:01.0 [1043:1864]
[   43.084107] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[   43.084111] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[   43.159733] Yenta: ISA IRQ mask 0x0008, PCI irq 4
[   43.159739] Socket status: 30000006
[   43.159741] Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06
[   43.159748] pcmcia: parent PCI bridge Memory window: 0xff900000 - 0xff9fffff
[   43.159752] pcmcia: parent PCI bridge Memory window: 0xdea00000 - 0xdeafffff
[   43.213230] Yenta: CardBus bridge found at 0000:02:01.1 [1043:1864]
[   43.339446] Yenta: ISA IRQ mask 0x0008, PCI irq 11
[   43.339451] Socket status: 30000006
[   43.339453] Yenta: Raising subordinate bus# of parent bus (#02) from #06 to #0a
[   43.339461] pcmcia: parent PCI bridge Memory window: 0xff900000 - 0xff9fffff
[   43.339464] pcmcia: parent PCI bridge Memory window: 0xdea00000 - 0xdeafffff
[   43.364646] ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
[   43.415076] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[   43.777157] Synaptics Touchpad, model: 1, fw: 4.6, id: 0x925ea1, caps: 0x80471b/0x0
[   43.815130] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
[   45.086523] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels)
[   45.086580] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 4 (level, low) -> IRQ 4
[   45.086605] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[   45.383699] cs: IO port probe 0x100-0x3af: clean.
[   45.385466] cs: IO port probe 0x3e0-0x4ff: clean.
[   45.385805] cs: IO port probe 0x820-0x8ff: clean.
[   45.386429] cs: IO port probe 0xc00-0xcf7: clean.
[   45.387214] cs: IO port probe 0xa00-0xaff: clean.
[   45.388060] cs: IO port probe 0x100-0x3af: clean.
[   45.389789] cs: IO port probe 0x3e0-0x4ff: clean.
[   45.390127] cs: IO port probe 0x820-0x8ff: clean.
[   45.390750] cs: IO port probe 0xc00-0xcf7: clean.
[   45.391537] cs: IO port probe 0xa00-0xaff: clean.
[   45.911144] intel8x0_measure_ac97_clock: measured 55460 usecs
[   45.911147] intel8x0: clocking to 48000
[   46.143388] lp0: using parport0 (interrupt-driven).
[   46.222063] Adding 1349420k swap on /dev/sda6.  Priority:-1 extents:1 across:1349420k
[   46.760491] EXT3 FS on sda5, internal journal
[   47.621368] kjournald starting.  Commit interval 5 seconds
[   47.621377] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[   47.621634] EXT3 FS on sda1, internal journal
[   47.621639] EXT3-fs: mounted filesystem with ordered data mode.
[   48.480787] ip_tables: (C) 2000-2006 Netfilter Core Team
[   49.047274] No dock devices found.
[   49.064974] ACPI: \_SB_.PCI0.IDE0.CHN1.DRV0: found ejectable bay
[   49.064983] ACPI: \_SB_.PCI0.IDE0.CHN1.DRV0: Adding notify handler
[   49.065018] ACPI: Error installing bay notify handler
[   49.065021] ACPI: Bay [\_SB_.PCI0.IDE0.CHN1.DRV0] Added
[   50.379631] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   50.379636] apm: overridden by ACPI.
[   50.726317] ppdev: user-space parallel port driver
[   50.920210] audit(1237282780.890:2): type=1503 operation="inode_permission" requested_mask="a::" denied_mask="a::" name="/dev/tty" pid=4986 profile="/usr/sbin/cupsd" namespace="default"
[  102.317874] Marking TSC unstable due to: cpufreq changes.
[  102.325824] Time: acpi_pm clocksource has been installed.
[  136.982265] Clocksource tsc unstable (delta = -286482694 ns)
[   51.696231] ttyS1: LSR safety check engaged!
[  139.948295] Bluetooth: Core ver 2.11
[  139.960872] NET: Registered protocol family 31
[  139.960882] Bluetooth: HCI device and connection manager initialized
[  139.960892] Bluetooth: HCI socket layer initialized
[  139.997819] Bluetooth: L2CAP ver 2.9
[  139.997829] Bluetooth: L2CAP socket layer initialized
[   52.487490] Bluetooth: RFCOMM socket layer initialized
[   52.487505] Bluetooth: RFCOMM TTY layer initialized
[   52.487507] Bluetooth: RFCOMM ver 1.8
[   53.621400] ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
[   56.220598] [fglrx] Internal AGP support requested, but kernel AGP support active.
[   56.220605] [fglrx] Have to use kernel AGP support to avoid conflicts.
[   56.220609] [fglrx] AGP detected, AgpState   = 0x1f000217 (hardware caps of chipset)
[   56.221152] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[   56.221299] agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
[   56.221460] agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
[   56.221624] [fglrx] AGP enabled,  AgpCommand = 0x1f000314 (selected caps)
[   56.225311] [fglrx] GART Table is not in FRAME_BUFFER range 
[   56.225319] [fglrx] Reserve Block - 0 offset =  0X0 length = 0X40000
[   56.225322] [fglrx] Reserve Block - 1 offset =  0X3ff5000 length = 0Xb000
[   56.334669] [fglrx] interrupt source 20008000 successfully enabled
[   56.334677] [fglrx] enable ID = 0x00000004
[   56.335010] [fglrx] Receive enable interrupt message with irqEnableMask: 20008000
[   56.335219] [fglrx] interrupt source 10000000 successfully enabled
[   56.335223] [fglrx] enable ID = 0x00000005
[   56.335485] [fglrx] Receive enable interrupt message with irqEnableMask: 10000000
[  174.071035] NET: Registered protocol family 10
[  174.072168] lo: Disabled Privacy Extensions
[  174.073501] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  174.074398] ADDRCONF(NETDEV_UP): eth1: link is not ready
[  203.530044] NET: Registered protocol family 17
[  122.613181] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   90.526872] eth1: no IPv6 routers present
[  520.004588] ACPI: EC: missing OBF confirmation, don't expect it any longer.
[  520.504380] ACPI: EC: missing write data confirmation, don't expect it any longer.
[ 7860.022673] pccard: PCMCIA card inserted into slot 0
[ 7860.022691] cs: memory probe 0xff900000-0xff9fffff: excluding 0xff900000-0xff90ffff 0xff9e0000-0xff9fffff
[ 7860.025641] pcmcia: registering new device pcmcia0.0
[ 2944.344946] 0.0: GetNextTuple: No more items
[ 2944.345141] pata_pcmcia: probe of 0.0 failed with error -12
[ 7862.763474] pccard: card ejected from slot 0
[ 7917.477220] pccard: PCMCIA card inserted into slot 0
[ 7917.477348] pcmcia: registering new device pcmcia0.0
[ 7917.477556] 0.0: GetNextTuple: No more items
[ 7917.477574] pata_pcmcia: probe of 0.0 failed with error -12
[ 7917.484217] 0.0: GetNextTuple: No more items
[ 7917.484569] pata_pcmcia: probe of 0.0 failed with error -12
[ 8073.637303] pccard: card ejected from slot 0
[ 8079.218276] pccard: PCMCIA card inserted into slot 0
[ 8079.218403] pcmcia: registering new device pcmcia0.0
[ 8079.218611] 0.0: GetNextTuple: No more items
[ 8079.218629] pata_pcmcia: probe of 0.0 failed with error -12
[ 8079.224123] 0.0: GetNextTuple: No more items
[ 8079.224451] pata_pcmcia: probe of 0.0 failed with error -12
[ 8100.755840] pccard: card ejected from slot 0
[ 8212.054887] pccard: PCMCIA card inserted into slot 0
[ 8212.055014] pcmcia: registering new device pcmcia0.0
[ 8212.055220] 0.0: GetNextTuple: No more items
[ 8212.055238] pata_pcmcia: probe of 0.0 failed with error -12
[ 8212.060787] 0.0: GetNextTuple: No more items
[ 8212.061115] pata_pcmcia: probe of 0.0 failed with error -12
[ 8215.552569] pccard: card ejected from slot 0
[ 8254.713339] pccard: PCMCIA card inserted into slot 0
[ 8254.713468] pcmcia: registering new device pcmcia0.0
[ 8254.713677] 0.0: GetNextTuple: No more items
[ 8254.713694] pata_pcmcia: probe of 0.0 failed with error -12
[ 8254.719216] 0.0: GetNextTuple: No more items
[ 8254.719549] pata_pcmcia: probe of 0.0 failed with error -12
[ 8335.816758] pccard: card ejected from slot 0
[ 8368.466070] cs: pcmcia_socket0: unable to apply power.
[ 8370.151444] pccard: PCMCIA card inserted into slot 0
[ 8370.151572] pcmcia: registering new device pcmcia0.0
[ 8370.151781] 0.0: GetNextTuple: No more items
[ 8370.151799] pata_pcmcia: probe of 0.0 failed with error -12
[ 8370.157413] 0.0: GetNextTuple: No more items
[ 8370.157747] pata_pcmcia: probe of 0.0 failed with error -12
[ 8812.170434] pccard: card ejected from slot 0
[ 8833.922072] pccard: PCMCIA card inserted into slot 0
[ 8833.922199] pcmcia: registering new device pcmcia0.0
[ 8833.922406] 0.0: GetNextTuple: No more items
[ 8833.922425] pata_pcmcia: probe of 0.0 failed with error -12
[ 8833.927965] 0.0: GetNextTuple: No more items
[ 8833.928292] pata_pcmcia: probe of 0.0 failed with error -12
[ 8860.105563] pccard: card ejected from slot 0
[ 8872.965775] pccard: PCMCIA card inserted into slot 0
[ 8872.965903] pcmcia: registering new device pcmcia0.0
[ 8872.966111] 0.0: GetNextTuple: No more items
[ 8872.966129] pata_pcmcia: probe of 0.0 failed with error -12
[ 8872.971704] 0.0: GetNextTuple: No more items
[ 8872.972033] pata_pcmcia: probe of 0.0 failed with error -12
[ 8884.710836] pccard: card ejected from slot 0
[ 8901.742356] pccard: PCMCIA card inserted into slot 0
[ 8901.742483] pcmcia: registering new device pcmcia0.0
[ 8901.742692] 0.0: GetNextTuple: No more items
[ 8901.742711] pata_pcmcia: probe of 0.0 failed with error -12
[ 8901.748369] 0.0: GetNextTuple: No more items
[ 8901.748699] pata_pcmcia: probe of 0.0 failed with error -12
[ 8944.799853] pccard: card ejected from slot 0
[ 8950.439284] pccard: PCMCIA card inserted into slot 0
[ 8950.439410] pcmcia: registering new device pcmcia0.0
[ 8950.439615] 0.0: GetNextTuple: No more items
[ 8950.439633] pata_pcmcia: probe of 0.0 failed with error -12
[ 8950.445270] 0.0: GetNextTuple: No more items
[ 8950.445608] pata_pcmcia: probe of 0.0 failed with error -12
[ 8966.232938] pccard: card ejected from slot 0
[ 8980.285936] pccard: PCMCIA card inserted into slot 0
[ 8980.286065] pcmcia: registering new device pcmcia0.0
[ 8980.286272] 0.0: GetNextTuple: No more items
[ 8980.286290] pata_pcmcia: probe of 0.0 failed with error -12
[ 8980.291918] 0.0: GetNextTuple: No more items
[ 8980.292258] pata_pcmcia: probe of 0.0 failed with error -12
[ 8982.423527] pccard: card ejected from slot 0
[ 8985.320111] pccard: PCMCIA card inserted into slot 0
[ 8985.320238] pcmcia: registering new device pcmcia0.0
[ 8985.320446] 0.0: GetNextTuple: No more items
[ 8985.320464] pata_pcmcia: probe of 0.0 failed with error -12
[ 8985.325983] 0.0: GetNextTuple: No more items
[ 8985.326310] pata_pcmcia: probe of 0.0 failed with error -12
[ 9009.816940] pccard: card ejected from slot 0
[ 9026.087678] pccard: PCMCIA card inserted into slot 0
[ 9026.087806] pcmcia: registering new device pcmcia0.0
[ 9026.088011] 0.0: GetNextTuple: No more items
[ 9026.088029] pata_pcmcia: probe of 0.0 failed with error -12
[ 9026.093582] 0.0: GetNextTuple: No more items
[ 9026.093915] pata_pcmcia: probe of 0.0 failed with error -12
[ 3404.531341] pccard: card ejected from slot 0
[12422.509630] pccard: PCMCIA card inserted into slot 0
[12422.509760] pcmcia: registering new device pcmcia0.0
[12422.509966] 0.0: GetNextTuple: No more items
[12422.509983] pata_pcmcia: probe of 0.0 failed with error -12
[12422.560536] 0.0: GetNextTuple: No more items
[12422.563266] pata_pcmcia: probe of 0.0 failed with error -12
[13558.670049] pccard: card ejected from slot 0
[13565.558676] pccard: PCMCIA card inserted into slot 0
[13565.558805] pcmcia: registering new device pcmcia0.0
[13565.559011] 0.0: GetNextTuple: No more items
[13565.559029] pata_pcmcia: probe of 0.0 failed with error -12
[13565.565718] 0.0: GetNextTuple: No more items
[13565.566063] pata_pcmcia: probe of 0.0 failed with error -12
[13972.941563] pccard: card ejected from slot 0
[13986.114139] pccard: PCMCIA card inserted into slot 0
[13986.114268] pcmcia: registering new device pcmcia0.0
[13986.114476] 0.0: GetNextTuple: No more items
[13986.114494] pata_pcmcia: probe of 0.0 failed with error -12
[13986.150191] 0.0: GetNextTuple: No more items
[13986.150559] pata_pcmcia: probe of 0.0 failed with error -12
ecco

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 13:33
da kapello
Hai provato un pò di volte a metterla e toglierla ... Comunque sembra riconoscere il lettore ma dà un errore quando inserisci la scheda.
Non so se si può fare qualcosa, bisogna fare una ricerca.., o che intervenga un "espertissimo" !!

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 13:38
da dfluisa
Ho provato, ma nulla!

Ok, grazie comunque dell'aiuto.E montarla manualmente???sapresti farlo? :-[

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 13:44
da kapello
E montarla manualmente???
Il problema è che finchè il dispositivo non viene riconosciuto correttamente non può essere montato, vedi
[13986.114139] pccard: PCMCIA card inserted into slot 0
[13986.114268] pcmcia: registering new device pcmcia0.0
[13986.114476] 0.0: GetNextTuple: No more items
[13986.114494] pata_pcmcia: probe of 0.0 failed with error -12
[13986.150191] 0.0: GetNextTuple: No more items
[13986.150559] pata_pcmcia: probe of 0.0 failed with error -12
Dà questo errore quando inserisci la card ...

edit:
Hai provato un pò di volte a metterla e toglierla ...
scusa mi sono espresso male non volevo dire di farlo, ma che l'avevi fatto !!

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 13:56
da dfluisa
ok...grazie dell'aiuto...spero in qualcun altro...purtroppo non avendo in dotazione il cavo usb è l'unico modo per caricare la schedina e inserire qualcosa nel cellulare!!! :'(

grazie dell'aiuto!!  :(

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 13:58
da bancaldo
inseriscila e posta

Codice: Seleziona tutto

dmesg | tail

non importa postare tutto il dmesg.
;)

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 13:59
da dfluisa
ecco:

luisa@PuoDarcy:~$ dmesg | tail
[15523.694634] 0.0: GetNextTuple: No more items
[15523.695007] pata_pcmcia: probe of 0.0 failed with error -12
[13038.514798] process `skype' is using obsolete setsockopt SO_BSDCOMPAT
[17564.621231] pccard: card ejected from slot 0
[17582.210770] pccard: PCMCIA card inserted into slot 0
[17582.210898] pcmcia: registering new device pcmcia0.0
[17582.211101] 0.0: GetNextTuple: No more items
[17582.211119] pata_pcmcia: probe of 0.0 failed with error -12
[17582.275073] 0.0: GetNextTuple: No more items
[17582.275414] pata_pcmcia: probe of 0.0 failed with error -12

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 14:06
da bancaldo
non la riconosce, ma il lettore di SD, viene riconosciuto come periferica?

posta il risultato

Codice: Seleziona tutto

lspci

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 14:10
da dfluisa
luisa@PuoDarcy:~$ lspci
00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 21)
00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 21)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03)
01:00.0 VGA compatible controller: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10]
02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5788 Gigabit Ethernet (rev 03)
02:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ac)
02:01.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ac)
02:01.2 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 04)
02:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG Network Connection (rev 05)
luisa@PuoDarcy:~$

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 14:13
da kapello
se può essere utile, nel dmesg c'era anche questo

Codice: Seleziona tutto

[   43.027737] Yenta: CardBus bridge found at 0000:02:01.0 [1043:1864]
[   43.213230] Yenta: CardBus bridge found at 0000:02:01.1 [1043:1864]
[   43.339446] Yenta: ISA IRQ mask 0x0008, PCI irq 11
[   43.339451] Socket status: 30000006
[   43.339453] Yenta: Raising subordinate bus# of parent bus (#02) from #06 to #0a
[   43.339461] pcmcia: parent PCI bridge Memory window: 0xff900000 - 0xff9fffff
[   43.339464] pcmcia: parent PCI bridge Memory window: 0xdea00000 - 0xdeafffff

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 14:17
da kapello
Ho cercato un pò in rete e mi sembra di aver capito che può essere un bug del kernel. Non so se ho capito bene (il mio inglese non è fantastico), ma forse è solo un problema di hotplug. Quindi puoi provare a fare sta prova: spegni il pc, metti la card e accendi il pc. Poi posta un

sudo fdisk -l

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 14:24
da dfluisa
ecco fatto:

Disco /dev/sda: 60.0 GB, 60011642880 byte
255 heads, 63 sectors/track, 7296 cylinders
Units = cilindri of 16065 * 512 = 8225280 bytes
Disk identifier: 0xee8cee8c

Dispositivo Boot      Start        End      Blocks  Id  System
/dev/sda1              1        3364    27021298+  83  Linux
/dev/sda2            3365        7296    31583790    5  Esteso
/dev/sda5            3365        7128    30234298+  83  Linux
/dev/sda6            7129        7296    1349428+  82  Linux swap / Solaris
luisa@PuoDarcy:~$

Re: problema lettura microsd

Inviato: martedì 17 marzo 2009, 14:34
da kapello
niente da fare.