Pagina 1 di 1

Server in crash ....

Inviato: venerdì 10 aprile 2009, 9:57
da Rages
Salve a tutti,

Un paio di mesi fa scrivevo per trovare aiuto per mettere su un piccolo server Ubuntu 8.10, tutto è andato piuttosto bene, grazie anche all'aiuto del forum, adesso però ha incominciato ad accusare dei problemi.

Il server è costituito da un AMD 2350BE con 4Gb di ram e 2 HD in raid 0 e un hd da 750Gb x il backup.

Il problema è questo ... mi appaiono un sacco di scritte strane e poi mi esce kernel panic e tutto si blocca ... riavvio ... mi dà un errore ACPI (se non erro...).
Non c'è un file log da postarvi x capirci qualcosa di più? o un comando da dare x fare apparire cosa non va?
Una volta riavviato mi resta su per una giornata ... dopo di nuovo kernel panic.

Re: Server in crash ....

Inviato: venerdì 10 aprile 2009, 10:00
da AlexSistemiFree
E' una rottura.

Se riesci ad entrare nel sistema magari puoi dare:
dmesg > dmesg.txt
però in realtà ci sono tanti file di log, a parte i casi in cui le eventuali problematiche sono mostrate solo su console e non scritte su nessun file di log.

Re: Server in crash ....

Inviato: venerdì 10 aprile 2009, 11:22
da Rages
posto il mio dmesg

[    8.542388]  sda1 sda2 input: NOVATEK USB Keyboard as /devices/pci0000:00/0000:00:04.0/usb2/2-6/2-6:1.1/input/input2
[    8.550952] input,hiddev96,hidraw1: USB HID v1.10 Device [NOVATEK USB Keyboard] on usb-0000:00:04.0-6
[    8.550975] usbcore: registered new interface driver usbhid
[    8.550979] usbhid: v2.6:USB HID core driver
[    8.559496]  sda5 >
[    8.559655] sd 0:0:0:0: [sda] Attached SCSI disk
[    8.559745] sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
[    8.559767] sd 1:0:0:0: [sdb] Write Protect is off
[    8.559770] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    8.559807] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    8.559874] sd 1:0:0:0: [sdb] 1465149168 512-byte hardware sectors (750156 MB)
[    8.559893] sd 1:0:0:0: [sdb] Write Protect is off
[    8.559896] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    8.559932] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    8.559936]  sdb: sdb1
[    8.566931] sd 1:0:0:0: [sdb] Attached SCSI disk
[    8.567023] sd 3:0:0:0: [sdc] 488397168 512-byte hardware sectors (250059 MB)
[    8.567045] sd 3:0:0:0: [sdc] Write Protect is off
[    8.567048] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    8.567086] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    8.567157] sd 3:0:0:0: [sdc] 488397168 512-byte hardware sectors (250059 MB)
[    8.567177] sd 3:0:0:0: [sdc] Write Protect is off
[    8.567179] sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[    8.567216] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    8.567220]  sdc: sdc1 sdc2 ata8: port disabled. ignoring.
[    8.598512]  sdc5 >
[    8.598680] sd 3:0:0:0: [sdc] Attached SCSI disk
[    8.993704] PM: Starting manual resume from disk
[    8.993708] PM: Resume from partition 254:2
[    8.993710] PM: Checking hibernation image.
[    8.993850] PM: Resume from disk failed.
[    9.014898] EXT3-fs: INFO: recovery required on readonly filesystem.
[    9.014903] EXT3-fs: write access will be enabled during recovery.
[    9.530475] kjournald starting.  Commit interval 5 seconds
[    9.530491] EXT3-fs: dm-1: orphan cleanup on readonly fs
[    9.530499] ext3_orphan_cleanup: deleting unreferenced inode 6135816
[    9.530529] ext3_orphan_cleanup: deleting unreferenced inode 6135815
[    9.530536] ext3_orphan_cleanup: deleting unreferenced inode 6135814
[    9.530542] ext3_orphan_cleanup: deleting unreferenced inode 6135813
[    9.530549] ext3_orphan_cleanup: deleting unreferenced inode 6135812
[    9.530555] EXT3-fs: dm-1: 5 orphan inodes deleted
[    9.530557] EXT3-fs: recovery complete.
[    9.537466] EXT3-fs: mounted filesystem with ordered data mode.
[    9.741466] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[001e8c00017fbc25]
[  11.791188] udevd version 124 started
[  12.297197] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[  12.345960] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 21
[  12.345967] HDA Intel 0000:00:07.0: PCI INT A -> Link[AAZA] -> GSI 21 (level, low) -> IRQ 21
[  12.345989] HDA Intel 0000:00:07.0: setting latency timer to 64
[  12.361307] ACPI: Power Button (FF) [PWRF]
[  12.361400] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
[/sub]

Re: Server in crash ....

Inviato: venerdì 10 aprile 2009, 11:22
da Rages
[  12.424096] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[  12.441319] ACPI: Power Button (CM) [PWRB]
[  14.235200] ACPI: WMI: Mapper loaded
[  14.376451] usbcore: registered new interface driver usbserial
[  14.376470] usbserial: USB Serial support registered for generic
[  14.376514] usbcore: registered new interface driver usbserial_generic
[  14.376517] usbserial: USB Serial Driver core
[  14.386140] usbserial: USB Serial support registered for GSM modem (1-port)
[  14.386169] option 1-6:1.0: GSM modem (1-port) converter detected
[  14.386350] usb 1-6: GSM modem (1-port) converter now attached to ttyUSB0
[  14.386365] option 1-6:1.1: GSM modem (1-port) converter detected
[  14.386441] usb 1-6: GSM modem (1-port) converter now attached to ttyUSB1
[  14.386454] option 1-6:1.2: GSM modem (1-port) converter detected
[  14.386527] usb 1-6: GSM modem (1-port) converter now attached to ttyUSB2
[  14.386542] usbcore: registered new interface driver option
[  14.386544] option: USB Driver for GSM modems: v0.7.2
[  14.716233] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[  14.719289] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[  15.031722] input: PC Speaker as /devices/platform/pcspkr/input/input5
[  16.537656] loop: module loaded
[  16.595831] lp: driver loaded but no devices found
[  16.908175] Adding 5301408k swap on /dev/mapper/nvidia_dcedbcab5.  Priority:-1 extents:1 across:5301408k
[  17.290275] EXT3 FS on dm-1, internal journal
[  17.635541] kjournald starting.  Commit interval 5 seconds
[  17.635965] EXT3 FS on sdb1, internal journal
[  17.635970] EXT3-fs: recovery complete.
[  17.636102] EXT3-fs: mounted filesystem with ordered data mode.
[  18.072765] type=1505 audit(1239348215.609:2): operation="profile_load" name="/usr/sbin/mysqld" name2="default" pid=4624
[  18.255185] ip_tables: (C) 2000-2006 Netfilter Core Team
[  18.336383] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[  18.336534] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Plase use
[  18.336537] nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
[  18.336539] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[  18.790566] NET: Registered protocol family 10
[  18.791128] lo: Disabled Privacy Extensions
[  23.263230] warning: `dhcpd3' uses 32-bit capabilities (legacy support in use)
[  23.397968] NET: Registered protocol family 17
[  29.660013] eth0: no IPv6 routers present
[  71.565916] PPP generic driver version 2.4.2
[  71.669806] PPP BSD Compression module registered
[  71.719394] PPP Deflate Compression module registered

Re: Server in crash ....

Inviato: martedì 21 aprile 2009, 8:15
da Rages
è possibile che questo mio problema sia dovuto alla RAM?

Ho installato 2 Gb (2x 1 Gb DDR2) Corsair Dominator 1066 MHz e ho provato a fare un memtest dopo un crash ... beh non ha passato un test sono usciti solo errori ... dovrei settare qualcosa di particolare x fare questi test? Mi suona un tantino strano che non passi proprio nulla.

Re: Server in crash ....

Inviato: martedì 21 aprile 2009, 9:37
da Stealth
Rages ha scritto: è possibile che questo mio problema sia dovuto alla RAM?

Ho installato 2 Gb (2x 1 Gb DDR2) Corsair Dominator 1066 MHz e ho provato a fare un memtest dopo un crash ... beh non ha passato un test sono usciti solo errori ...
Beh... >:(
Se fai un test ed escono solo errori, qualcosa che non va ci dovrebbe essere. Comincio? La ram è difettosa....il tuo sistema non supporta quel formato...il bios non è settato per far funzionare i nuovi banchi....
Per non farla troppo lunga, hai provato a togliere la nuova ram e a ripartire con la vecchia dotazione? Non è una prova astuta ma non può sbagliare e, se il pc parte, sai con chi prendertela
ciao

ps: sposto in hardware

Re: Server in crash ....

Inviato: martedì 21 aprile 2009, 11:16
da Rages
Non mi son spiegato bene .. quella ram è montata sin dall'inizio in quel modo .. ed ha sempre funzionato, (3 mesi + o - ) ma non mi spiego come .. infatti da quel che ho capito non è possibile montarle in quel modo.
Ho tolto un banco di RAM e con 1 Gb in single channel il memtest è tutto ok ;)

Il problema nasce col double channel credo che questa scheda non sopporti il double con 1066Mhz.

(O forse questo tipo di RAM).

Di fatto cmq anche in single la fa andare a 800Mhz.
Ho letto da qualche parte di provare ad alzare a 2,11V ho provato ma non cambia nulla.
Per il momento sto andando con 1 Gb e sembra stabile.

Re: Server in crash ....

Inviato: venerdì 24 aprile 2009, 9:12
da AlexSistemiFree
Il tuo sistema supporta memorie ddr o ddr2?

Impostando il tutto a 800 ti funziona pure con 2 schede anziché soltanto una?

Non so la tua motherboard di quanti slot per la ram disponga però capita che escano alcuni modelli sfortunati in cui è presente un problema hardware per cui nei fatti non sono in grado di gestire tutta la memoria che teoricamente potrebbero gestire.

Comunque, se per sbaglio, ti capitasse di provare della ram di un'altra marca, chissà se funziona.