[Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Riconoscimento, installazione e configurazione delle periferiche.
nina
Prode Principiante
Messaggi: 18
Iscrizione: martedì 26 maggio 2009, 19:15

[Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da nina »

Ho provato a montare l'hard disk seguendo tutte le strade proposte sul forum e sulla guida ma non viene proprio riconosciuto.
Aiutooooo perfavore sono nuova ad ubuntu, quindi c'è qualcuno che può spiegarmi come fare in un linguaggio semplice? Ho lo stesso problema anche con la memory card della fotocamera. Grazie
Avatar utente
maveloth
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 488
Iscrizione: lunedì 17 marzo 2008, 20:01
Località: Lucca

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da maveloth »

quando provi a montarlo(e specificando come) che errore ti da?

Maveloth
nina
Prode Principiante
Messaggi: 18
Iscrizione: martedì 26 maggio 2009, 19:15

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da nina »

dato che ho provato piu strade senza capirci granche ora non mi ricordo...potremmo riniziare di nuovo passo per passo?grazie in anticipo
Avatar utente
maveloth
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 488
Iscrizione: lunedì 17 marzo 2008, 20:01
Località: Lucca

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da maveloth »

da terminale dai questo comando e postami l'output

Codice: Seleziona tutto

sudo fdisk -l
Maveloth
nina
Prode Principiante
Messaggi: 18
Iscrizione: martedì 26 maggio 2009, 19:15

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da nina »

(da root) ho digitato da terminale: sudo fdisk -l

e mi esce questo:

Disco /dev/sda: 40.0 GB, 40007761920 byte
255 testine, 63 settori/tracce, 4864 cilindri
Unità = cilindri di 16065 * 512 = 8225280 byte
Identificativo disco: 0x587d2489

Dispositivo Boot      Start         End      Blocks   Id  System
/dev/sda1   *           1        4683    37616166   83  Linux
/dev/sda2            4684        4864     1453882+   5  Esteso
/dev/sda5            4684        4864     1453851   82  Linux swap / Solaris

cio vuol dire che nn lo legge proprio?grazie
Avatar utente
maveloth
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 488
Iscrizione: lunedì 17 marzo 2008, 20:01
Località: Lucca

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da maveloth »

allora prova a staccarlo e riattaccarlo dopodichè posta il risultato del comando

Codice: Seleziona tutto

dmesg
Maveloth
nina
Prode Principiante
Messaggi: 18
Iscrizione: martedì 26 maggio 2009, 19:15

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da nina »

[    0.609327] system 00:08: ioport range 0x12d4-0x12d4 has been reserved
[    0.609330] system 00:08: ioport range 0x1300-0x1375 has been reserved
[    0.609333] system 00:08: ioport range 0x1377-0x137f has been reserved
[    0.609336] system 00:08: ioport range 0x200-0x20f has been reserved
[    0.609339] system 00:08: ioport range 0x860-0x86f has been reserved
[    0.609343] system 00:08: iomem range 0xfec00000-0xfec00fff has been reserved
[    0.609346] system 00:08: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.609349] system 00:08: iomem range 0xfec10000-0xfec1ffff has been reserved
[    0.609352] system 00:08: iomem range 0xffe80000-0xffefffff has been reserved
[    0.609355] system 00:08: iomem range 0xfff80000-0xffffffff has been reserved
[    0.609359] system 00:08: iomem range 0xfee00400-0xffbfffff could not be reserved
[    0.609362] system 00:08: iomem range 0xfff00000-0xfff7ffff has been reserved
[    0.609368] system 00:09: iomem range 0x0-0x9ffff could not be reserved
[    0.609371] system 00:09: iomem range 0xe0000-0xfffff could not be reserved
[    0.609375] system 00:09: iomem range 0x100000-0x1effffff could not be reserved
[    0.644084] pci 0000:01:03.0: CardBus bridge, secondary bus 0000:02
[    0.644087] pci 0000:01:03.0:  IO window: 0x00c000-0x00c0ff
[    0.644092] pci 0000:01:03.0:  IO window: 0x00c400-0x00c4ff
[    0.644096] pci 0000:01:03.0:  PREFETCH window: 0x20000000-0x23ffffff
[    0.644101] pci 0000:01:03.0:  MEM window: 0x2c000000-0x2fffffff
[    0.644105] pci 0000:01:03.1: CardBus bridge, secondary bus 0000:06
[    0.644107] pci 0000:01:03.1:  IO window: 0x00cc00-0x00ccff
[    0.644112] pci 0000:01:03.1:  IO window: 0x001000-0x0010ff
[    0.644116] pci 0000:01:03.1:  PREFETCH window: 0x24000000-0x27ffffff
[    0.644120] pci 0000:01:03.1:  MEM window: 0x30000000-0x33ffffff
[    0.644125] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
[    0.644129] pci 0000:00:1e.0:  IO window: 0xc000-0xcfff
[    0.644134] pci 0000:00:1e.0:  MEM window: 0xe0000000-0xe00fffff
[    0.644139] pci 0000:00:1e.0:  PREFETCH window: 0x00000020000000-0x00000027ffffff
[    0.644152] pci 0000:00:1e.0: setting latency timer to 64
[    0.644163] pci 0000:01:03.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    0.644170] pci 0000:01:03.1: enabling device (0000 -> 0003)
[    0.644174] pci 0000:01:03.1: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    0.644181] bus: 00 index 0 io port: [0x00-0xffff]
[    0.644183] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[    0.644186] bus: 01 index 0 io port: [0xc000-0xcfff]
[    0.644189] bus: 01 index 1 mmio: [0xe0000000-0xe00fffff]
[    0.644191] bus: 01 index 2 mmio: [0x20000000-0x27ffffff]
[    0.644194] bus: 01 index 3 io port: [0x00-0xffff]
[    0.644196] bus: 01 index 4 mmio: [0x000000-0xffffffff]
[    0.644198] bus: 02 index 0 io port: [0xc000-0xc0ff]
[    0.644201] bus: 02 index 1 io port: [0xc400-0xc4ff]
[    0.644203] bus: 02 index 2 mmio: [0x20000000-0x23ffffff]
[    0.644206] bus: 02 index 3 mmio: [0x2c000000-0x2fffffff]
[    0.644208] bus: 06 index 0 io port: [0xcc00-0xccff]
[    0.644211] bus: 06 index 1 io port: [0x1000-0x10ff]
[    0.644213] bus: 06 index 2 mmio: [0x24000000-0x27ffffff]
[    0.644216] bus: 06 index 3 mmio: [0x30000000-0x33ffffff]
[    0.644225] NET: Registered protocol family 2
[    0.644333] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.644559] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.644655] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[    0.644752] TCP: Hash tables configured (established 16384 bind 16384)
[    0.644755] TCP reno registered
[    0.644821] NET: Registered protocol family 1
[    0.644948] checking if image is initramfs... it is
[    1.148018] Switched to high resolution mode on CPU 0
[    1.355286] Freeing initrd memory: 7367k freed
[    1.355395] cpufreq: No nForce2 chipset.
[    1.355590] audit: initializing netlink socket (disabled)
[    1.355617] type=2000 audit(1243353558.352:1): initialized
[    1.364171] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.365596] VFS: Disk quotas dquot_6.5.1
[    1.365657] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.366320] fuse init (API version 7.10)
[    1.366409] msgmni has been set to 962
[    1.366618] alg: No test for stdrng (krng)
[    1.366632] io scheduler noop registered
[    1.366634] io scheduler anticipatory registered
[    1.366637] io scheduler deadline registered
[    1.366652] io scheduler cfq registered (default)
[    1.366672] pci 0000:00:02.0: Boot video device
[    1.369198] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.369209] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.369724] ACPI: AC Adapter [AC0] (on-line)
[    1.421686] ACPI: Battery Slot [BAT0] (battery present)
[    1.421758] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    1.421761] ACPI: Power Button (FF) [PWRF]
[    1.421816] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
[    1.421857] ACPI: Lid Switch [liD]
[    1.421903] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[    1.421906] ACPI: Sleep Button (CM) [SLPB]
[    1.421950] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[    1.421953] ACPI: Power Button (CM) [PWRB]
[    1.422242] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[    1.422268] processor ACPI_CPU:00: registered as cooling_device0
[    1.422272] ACPI: Processor [CPU1] (supports 8 throttling states)
[    1.423883] thermal LNXTHERM:01: registered as thermal_zone0
[    1.424036] ACPI: Thermal Zone [THRM] (11 C)
[    1.424078] isapnp: Scanning for PnP cards...
[    1.777611] isapnp: No Plug & Play device found
[    1.778766] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.779826] brd: module loaded
[    1.780162] loop: module loaded
[    1.780238] Fixed MDIO Bus: probed
[    1.780244] PPP generic driver version 2.4.2
[    1.780308] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[    1.780340] Driver 'sd' needs updating - please use bus_type methods
[    1.780350] Driver 'sr' needs updating - please use bus_type methods
[    1.780427] ata_piix 0000:00:1f.1: version 2.12
[    1.780436] ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
[    1.780449] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    1.780489] ata_piix 0000:00:1f.1: setting latency timer to 64
[    1.780571] scsi0 : ata_piix
[    1.780653] scsi1 : ata_piix
[    1.782465] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    1.782468] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    1.944921] ata1.00: ATA-6: ST94019A, 3.05, max UDMA/100
[    1.944924] ata1.00: 78140160 sectors, multi 16: LBA48
[    1.961603] ata1.00: configured for UDMA/100
[    2.124265] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-T10N, PW02, max UDMA/33
[    2.140222] ata2.00: configured for UDMA/33
[    2.142649] scsi 0:0:0:0: Direct-Access    ATA      ST94019A        3.05 PQ: 0 ANSI: 5
[    2.142748] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors: (40.0 GB/37.2 GiB)
[    2.142766] sd 0:0:0:0: [sda] Write Protect is off
[    2.142769] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.142796] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.142857] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors: (40.0 GB/37.2 GiB)
[    2.142872] sd 0:0:0:0: [sda] Write Protect is off
[    2.142875] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.142900] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.142904]  sda: sda1 sda2
[    2.417747] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.417794] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.421535] scsi 1:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T10N  PW02 PQ: 0 ANSI: 5
[    2.433121] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.433125] Uniform CD-ROM driver Revision: 3.20
[    2.433213] sr 1:0:0:0: Attached scsi CD-ROM sr0
[    2.433250] sr 1:0:0:0: Attached scsi generic sg1 type 5
[    2.433898] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.433919] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[    2.433943] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    2.433947] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    2.434016] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    2.437941] ehci_hcd 0000:00:1d.7: debug port 1
[    2.437947] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    2.437962] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xe02ffc00
[    2.452007] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    2.452092] usb usb1: configuration #1 chosen from 1 choice
[    2.452122] hub 1-0:1.0: USB hub found
[    2.452131] hub 1-0:1.0: 6 ports detected
[    2.452240] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.452257] uhci_hcd: USB Universal Host Controller Interface driver
[    2.452280] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    2.452287] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    2.452290] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.452343] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    2.452368] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000e480
[    2.452439] usb usb2: configuration #1 chosen from 1 choice
[    2.452464] hub 2-0:1.0: USB hub found
[    2.452473] hub 2-0:1.0: 2 ports detected
[    2.452558] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    2.452564] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    2.452567] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.452608] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    2.452636] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e800
[    2.452706] usb usb3: configuration #1 chosen from 1 choice
[    2.452736] hub 3-0:1.0: USB hub found
[    2.452743] hub 3-0:1.0: 2 ports detected
[    2.452817] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    2.452823] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    2.452826] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.452867] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    2.452892] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e880
[    2.452968] usb usb4: configuration #1 chosen from 1 choice
[    2.452993] hub 4-0:1.0: USB hub found
[    2.453000] hub 4-0:1.0: 2 ports detected
[    2.453122] usbcore: registered new interface driver libusual
[    2.453156] usbcore: registered new interface driver usbserial
[    2.453167] USB Serial support registered for generic
[    2.453182] usbcore: registered new interface driver usbserial_generic
[    2.453184] usbserial: USB Serial Driver core
[    2.453233] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    2.457730] i8042.c: Detected active multiplexing controller, rev 1.0.
[    2.458589] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.458595] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    2.458597] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    2.458600] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    2.458603] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    2.458764] mice: PS/2 mouse device common for all mice
[    2.458980] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    2.459000] rtc0: alarms up to one month, 114 bytes nvram
[    2.459066] device-mapper: uevent: version 1.0.3
[    2.459171] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[    2.459231] device-mapper: multipath: version 1.0.5 loaded
[    2.459235] device-mapper: multipath round-robin: version 1.0.0 loaded
[    2.459320] EISA: Probing bus 0 at eisa.0
[    2.459327] Cannot allocate resource for EISA slot 1
[    2.459355] EISA: Detected 0 cards.
[    2.459424] cpuidle: using governor ladder
[    2.459488] cpuidle: using governor menu
[    2.460018] TCP cubic registered
[    2.460127] NET: Registered protocol family 10
[    2.460534] lo: Disabled Privacy Extensions
[    2.460851] NET: Registered protocol family 17
[    2.460869] Bluetooth: L2CAP ver 2.11
[    2.460870] Bluetooth: L2CAP socket layer initialized
[    2.460874] Bluetooth: SCO (Voice Link) ver 0.6
[    2.460876] Bluetooth: SCO socket layer initialized
[    2.460904] Bluetooth: RFCOMM socket layer initialized
[    2.460910] Bluetooth: RFCOMM TTY layer initialized
[    2.460912] Bluetooth: RFCOMM ver 1.10
[    2.461176] Using IPI No-Shortcut mode
[    2.461257] registered taskstats version 1
[    2.461378]  Magic number: 9:979:993
[    2.461445] rtc_cmos 00:02: setting system clock to 2009-05-26 15:59:20 UTC (1243353560)
[    2.461449] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    2.461451] EDD information not available.
[    2.461754] Freeing unused kernel memory: 532k freed
[    2.461877] Write protecting the kernel text: 4128k
[    2.461919] Write protecting the kernel read-only data: 1532k
[    2.463579] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[    3.004028] usb 3-1: new low speed USB device using uhci_hcd and address 2
[    3.138473] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[    3.138520] 8139cp 0000:01:0c.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[    3.141684] 8139too Fast Ethernet driver 0.9.28
[    3.141722] 8139too 0000:01:0c.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[    3.142645] eth0: RealTek RTL8139 at 0xc800, 00:03:0d:25:46:b4, IRQ 19
[    3.142648] eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
[    3.146261] ohci1394 0000:01:0a.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    3.196014] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18]  MMIO=[e00fd800-e00fdfff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[    3.234634] usb 3-1: configuration #1 chosen from 1 choice
[    3.448394] usbcore: registered new interface driver hiddev
[    3.453447] Marking TSC unstable due to TSC halts in idle
[    3.461880] input: Acrox USB & PS/2 Mouse as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input6
[    3.462121] generic-usb 0003:0F62:1001.0001: input,hidraw0: USB HID v1.10 Mouse [Acrox USB & PS/2 Mouse] on usb-0000:00:1d.1-1/input0
[    3.462137] usbcore: registered new interface driver usbhid
[    3.462140] usbhid: v2.6:USB HID core driver
[    3.746468] PM: Starting manual resume from disk
[    3.746472] PM: Resume from partition 8:5
[    3.746474] PM: Checking hibernation image.
[    3.747450] PM: Resume from disk failed.
[    3.794097] kjournald starting.  Commit interval 5 seconds
[    3.794108] EXT3-fs: mounted filesystem with ordered data mode.
[    4.468150] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00030d4925538bb8]
[  13.055237] udev: starting version 141
[  13.531590] Linux agpgart interface v0.103
[  13.800437] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:14/input/input7
[  13.802670] ACPI: Video Device [IGD] (multi-head: yes  rom: no  post: no)
[  13.813822] input: PC Speaker as /devices/platform/pcspkr/input/input8
[  13.856451] agpgart-intel 0000:00:00.0: Intel 855GM Chipset
[  13.856973] agpgart-intel 0000:00:00.0: detected 16252K stolen memory
[  13.858840] agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xd8000000
[  13.900320] intel_rng: FWH not detected
[  14.109775] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[  14.206884] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[  14.286271] yenta_cardbus 0000:01:03.0: CardBus bridge found [1734:106a]
[  14.286290] yenta_cardbus 0000:01:03.0: O2: res at 0x94/0xD4: 00/ea
[  14.286293] yenta_cardbus 0000:01:03.0: O2: enabling read prefetch/write burst
[  14.301288] ieee80211_crypt: registered algorithm 'NULL'
[  14.307601] ieee80211: 802.11 data/management/control stack, git-1.1.13
[  14.307604] ieee80211: Copyright (C) 2004-2005 Intel Corporation
[  14.391645] iTCO_vendor_support: vendor-support=0
[  14.413247] yenta_cardbus 0000:01:03.0: ISA IRQ mask 0x0cb8, PCI irq 17
[  14.413252] yenta_cardbus 0000:01:03.0: Socket status: 30000006
[  14.413256] pci_bus 0000:01: Raising subordinate bus# of parent bus (#01) from #01 to #05
[  14.413277] yenta_cardbus 0000:01:03.0: pcmcia: parent PCI bridge I/O window: 0xc000 - 0xcfff
[  14.413281] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc000-0xcfff: clean.
[  14.413502] yenta_cardbus 0000:01:03.0: pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xe00fffff
[  14.413505] yenta_cardbus 0000:01:03.0: pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x27ffffff
[  14.414061] yenta_cardbus 0000:01:03.1: CardBus bridge found [1734:106a]
[  14.425201] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq
[  14.425204] ipw2200: Copyright(c) 2003-2006 Intel Corporation
[  14.429569] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[  14.429691] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x0460)
[  14.429782] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[  14.541344] yenta_cardbus 0000:01:03.1: ISA IRQ mask 0x0cb8, PCI irq 17
[  14.541350] yenta_cardbus 0000:01:03.1: Socket status: 30000006
[  14.541354] pci_bus 0000:01: Raising subordinate bus# of parent bus (#01) from #05 to #09
[  14.541364] yenta_cardbus 0000:01:03.1: pcmcia: parent PCI bridge I/O window: 0xc000 - 0xcfff
[  14.541368] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc000-0xcfff: clean.
[  14.541589] yenta_cardbus 0000:01:03.1: pcmcia: parent PCI bridge Memory window: 0xe0000000 - 0xe00fffff
[  14.541592] yenta_cardbus 0000:01:03.1: pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x27ffffff
[  14.545300] ipw2200 0000:01:07.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[  14.545524] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[  14.545566] ipw2200 0000:01:07.0: firmware: requesting ipw2200-bss.fw
[  14.808437] ipw2200: Detected geography ZZR (14 802.11bg channels, 0 802.11a channels)
[  14.884720] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[  14.886337] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[  14.886727] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[  14.887262] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[  14.888011] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[  14.940534] Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[  14.940627] Intel ICH 0000:00:1f.5: setting latency timer to 64
[  15.162256] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x6eb1, caps: 0xa04711/0x40a
[  15.209524] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input9
[  15.320831] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af: clean.
[  15.322416] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff: clean.
[  15.322805] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff: clean.
[  15.323340] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7: clean.
[  15.324089] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
[  16.216019] AC'97 1 does not respond - RESET
[  16.216232] AC'97 1 access is not valid [0xffffffff], removing mixer.
[  16.216238] Unable to initialize codec #1
[  16.272030] intel8x0_measure_ac97_clock: measured 55568 usecs
[  16.272033] intel8x0: clocking to 48000
[  16.662371] lp: driver loaded but no devices found
[  16.800113] Adding 1453840k swap on /dev/sda5.  Priority:-1 extents:1 across:1453840k
[  17.348369] EXT3 FS on sda1, internal journal
[  18.375359] type=1505 audit(1243353576.410:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=1988
[  18.431743] type=1505 audit(1243353576.466:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1992
[  18.431868] type=1505 audit(1243353576.466:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1992
[  18.431919] type=1505 audit(1243353576.466:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1992
[  18.431963] type=1505 audit(1243353576.466:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1992
[  18.598917] type=1505 audit(1243353576.634:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1997
[  18.599220] type=1505 audit(1243353576.634:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1997
[  18.631242] type=1505 audit(1243353576.666:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2001
[  21.141468] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[  21.141472] Bluetooth: BNEP filters: protocol multicast
[  21.189891] Bridge firewalling registered
[  23.280020] ppdev: user-space parallel port driver
[  24.581683] [drm] Initialized drm 1.1.0 20060810
[  24.659265] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[  24.659271] pci 0000:00:02.0: setting latency timer to 64
[  24.659464] [drm] Initialized i915 1.6.0 20080730 on minor 0
[  24.662221] [drm:i915_setparam] *ERROR* unknown parameter 4
[  24.662245] [drm:i915_getparam] *ERROR* Unknown parameter 6
[  26.575566] [drm:i915_getparam] *ERROR* Unknown parameter 6
[  26.963168] eth0: link down
[  26.963251] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  37.904019] eth1: no IPv6 routers present
[  82.106532] [drm:i915_getparam] *ERROR* Unknown parameter 6
[  85.144026] Clocksource tsc unstable (delta = -106136053 ns)
[  94.050481] ieee80211_crypt: registered algorithm 'TKIP'
[  140.640408] ieee80211_crypt: registered algorithm 'WEP'
[  482.508045] usb 1-5: new high speed USB device using ehci_hcd and address 3
[  482.641270] usb 1-5: configuration #1 chosen from 1 choice
[  482.861346] Initializing USB Mass Storage driver...
[  482.862627] scsi2 : SCSI emulation for USB Mass Storage devices
[  482.863149] usbcore: registered new interface driver usb-storage
[  482.863159] USB Mass Storage support registered.
[  482.865445] usb-storage: device found at 3
[  482.865452] usb-storage: waiting for device to settle before scanning
[  487.864298] usb-storage: device scan complete
[  487.864896] scsi scan: INQUIRY result too short (5), using 36
[  487.864908] scsi 2:0:0:0: CD-ROM            Toshiba  USB 2.0 CD-ROM  1.15 PQ: 0 ANSI: 0
[  487.866512] scsi 2:0:0:1: Direct-Access    Toshiba  USB 2.0 Ext. HDD 1.15 PQ: 0 ANSI: 0
[  487.919573] sr1: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[  487.919836] sr 2:0:0:0: Attached scsi CD-ROM sr1
[  487.919995] sr 2:0:0:0: Attached scsi generic sg2 type 5
[  487.921894] sd 2:0:0:1: [sdb] Attached SCSI disk
[  487.921951] sd 2:0:0:1: Attached scsi generic sg3 type 0
[  491.540042] ISO 9660 Extensions: Microsoft Joliet Level 3
[  491.541018] ISO 9660 Extensions: RRIP_1991A
[ 2072.364184] usb 1-5: USB disconnect, address 3
[ 2072.605201] scsi 2:0:0:0: rejecting I/O to dead device
[ 2072.605214] scsi 2:0:0:0: rejecting I/O to dead device
[ 2169.964221] usb 1-5: new high speed USB device using ehci_hcd and address 4
[ 2170.100955] usb 1-5: configuration #1 chosen from 1 choice
[ 2170.103174] scsi3 : SCSI emulation for USB Mass Storage devices
[ 2170.105770] usb-storage: device found at 4
[ 2170.105777] usb-storage: waiting for device to settle before scanning
[ 2175.104293] usb-storage: device scan complete
[ 2175.104908] scsi scan: INQUIRY result too short (5), using 36
[ 2175.104921] scsi 3:0:0:0: CD-ROM            Toshiba  USB 2.0 CD-ROM  1.15 PQ: 0 ANSI: 0
[ 2175.106523] scsi 3:0:0:1: Direct-Access    Toshiba  USB 2.0 Ext. HDD 1.15 PQ: 0 ANSI: 0
[ 2175.165094] sr1: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[ 2175.165222] sr 3:0:0:0: Attached scsi CD-ROM sr1
[ 2175.165311] sr 3:0:0:0: Attached scsi generic sg2 type 5
[ 2175.166013] sd 3:0:0:1: [sdb] Attached SCSI disk
[ 2175.166062] sd 3:0:0:1: Attached scsi generic sg3 type 0
[ 2178.473804] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 2178.474793] ISO 9660 Extensions: RRIP_1991A
[ 2999.361353] usb 1-5: USB disconnect, address 4
[ 2999.507002] scsi 3:0:0:0: rejecting I/O to dead device
[ 2999.507020] scsi 3:0:0:0: rejecting I/O to dead device
[ 3238.012051] usb 1-5: new high speed USB device using ehci_hcd and address 5
[ 3238.153295] usb 1-5: configuration #1 chosen from 1 choice
[ 3238.155454] scsi4 : SCSI emulation for USB Mass Storage devices
[ 3238.157959] usb-storage: device found at 5
[ 3238.157966] usb-storage: waiting for device to settle before scanning
[ 3243.156320] usb-storage: device scan complete
[ 3243.156932] scsi scan: INQUIRY result too short (5), using 36
[ 3243.156944] scsi 4:0:0:0: CD-ROM            Toshiba  USB 2.0 CD-ROM  1.15 PQ: 0 ANSI: 0
[ 3243.158553] scsi 4:0:0:1: Direct-Access    Toshiba  USB 2.0 Ext. HDD 1.15 PQ: 0 ANSI: 0
[ 3243.215481] sr1: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[ 3243.215610] sr 4:0:0:0: Attached scsi CD-ROM sr1
[ 3243.215699] sr 4:0:0:0: Attached scsi generic sg2 type 5
[ 3243.216799] sd 4:0:0:1: [sdb] Attached SCSI disk
[ 3243.216848] sd 4:0:0:1: Attached scsi generic sg3 type 0
[ 3246.468594] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 3246.469584] ISO 9660 Extensions: RRIP_1991A
[ 3800.355651] usb 1-5: USB disconnect, address 5
[ 3807.932056] usb 1-5: new high speed USB device using ehci_hcd and address 6
[ 3808.072245] usb 1-5: configuration #1 chosen from 1 choice
[ 3808.074405] scsi5 : SCSI emulation for USB Mass Storage devices
[ 3808.076927] usb-storage: device found at 6
[ 3808.076933] usb-storage: waiting for device to settle before scanning
[ 3813.076226] usb-storage: device scan complete
[ 3813.076838] scsi scan: INQUIRY result too short (5), using 36
[ 3813.076851] scsi 5:0:0:0: CD-ROM            Toshiba  USB 2.0 CD-ROM  1.15 PQ: 0 ANSI: 0
[ 3813.078454] scsi 5:0:0:1: Direct-Access    Toshiba  USB 2.0 Ext. HDD 1.15 PQ: 0 ANSI: 0
[ 3813.137161] sr1: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[ 3813.137403] sr 5:0:0:0: Attached scsi CD-ROM sr1
[ 3813.137563] sr 5:0:0:0: Attached scsi generic sg2 type 5
[ 3813.138570] sd 5:0:0:1: [sdb] Attached SCSI disk
[ 3813.138690] sd 5:0:0:1: Attached scsi generic sg3 type 0
[ 3816.551966] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 3816.553463] ISO 9660 Extensions: RRIP_1991A
[ 3897.865427] usb 1-5: USB disconnect, address 6
[ 5373.240048] usb 1-5: new high speed USB device using ehci_hcd and address 7
[ 5373.421260] usb 1-5: configuration #1 chosen from 1 choice
[ 5373.465718] scsi6 : SCSI emulation for USB Mass Storage devices
[ 5373.468954] usb-storage: device found at 7
[ 5373.468962] usb-storage: waiting for device to settle before scanning
[ 5378.468396] usb-storage: device scan complete
[ 5378.469132] scsi scan: INQUIRY result too short (5), using 36
[ 5378.469138] scsi 6:0:0:0: CD-ROM            Toshiba  USB 2.0 CD-ROM  1.15 PQ: 0 ANSI: 0
[ 5378.471158] scsi 6:0:0:1: Direct-Access    Toshiba  USB 2.0 Ext. HDD 1.15 PQ: 0 ANSI: 0
[ 5378.525354] sr1: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[ 5378.525569] sr 6:0:0:0: Attached scsi CD-ROM sr1
[ 5378.525706] sr 6:0:0:0: Attached scsi generic sg2 type 5
[ 5378.531115] sd 6:0:0:1: [sdb] Attached SCSI disk
[ 5378.531203] sd 6:0:0:1: Attached scsi generic sg3 type 0
[ 5381.297260] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 5381.298199] ISO 9660 Extensions: RRIP_1991A
[ 7492.691200] usb 1-5: USB disconnect, address 7
[ 7492.799203] scsi 6:0:0:0: rejecting I/O to dead device
[ 7492.799221] scsi 6:0:0:0: rejecting I/O to dead device
[ 7503.068073] usb 1-5: new high speed USB device using ehci_hcd and address 8
[ 7503.245416] usb 1-5: configuration #1 chosen from 1 choice
[ 7503.293289] scsi7 : SCSI emulation for USB Mass Storage devices
[ 7503.305485] usb-storage: device found at 8
[ 7503.305490] usb-storage: waiting for device to settle before scanning
[ 7508.304218] usb-storage: device scan complete
[ 7508.304833] scsi scan: INQUIRY result too short (5), using 36
[ 7508.304846] scsi 7:0:0:0: CD-ROM            Toshiba  USB 2.0 CD-ROM  1.15 PQ: 0 ANSI: 0
[ 7508.306448] scsi 7:0:0:1: Direct-Access    Toshiba  USB 2.0 Ext. HDD 1.15 PQ: 0 ANSI: 0
[ 7508.366055] sr1: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[ 7508.366302] sr 7:0:0:0: Attached scsi CD-ROM sr1
[ 7508.366460] sr 7:0:0:0: Attached scsi generic sg2 type 5
[ 7508.369961] sd 7:0:0:1: [sdb] Attached SCSI disk
[ 7508.370097] sd 7:0:0:1: Attached scsi generic sg3 type 0
Avatar utente
maveloth
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 488
Iscrizione: lunedì 17 marzo 2008, 20:01
Località: Lucca

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da maveloth »

stai usando un notebook o un fisso?

nel caso tu stia usando un fisso a quale porta lo stai collegando?

Maveloth

EDIT:hai la possibilità di usare windows? se sì prova ad attaccarlo e vedi che non sia protetto da password...
Ultima modifica di maveloth il martedì 26 maggio 2009, 20:47, modificato 1 volta in totale.
nina
Prode Principiante
Messaggi: 18
Iscrizione: martedì 26 maggio 2009, 19:15

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da nina »

un notebook
nina
Prode Principiante
Messaggi: 18
Iscrizione: martedì 26 maggio 2009, 19:15

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da nina »

l'hardisk prima andava con windows ed ha una password
Avatar utente
maveloth
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 488
Iscrizione: lunedì 17 marzo 2008, 20:01
Località: Lucca

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da maveloth »

se puoi usare windows basta che togli la password e dovrebbe funzionare normalmente.

Maveloth
nina
Prode Principiante
Messaggi: 18
Iscrizione: martedì 26 maggio 2009, 19:15

[Risolto] Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?RISOLTO

Messaggio da nina »

RISOLTOOOO!!! grazie mille per l'aiuto non sapevo veramente come fare.sei stato gentilissimo
p.s. mica sai come posso fare per la memory card...non la legge proprio al mio computer ma in altri notebook con ubuntu la legge.
Avatar utente
maveloth
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 488
Iscrizione: lunedì 17 marzo 2008, 20:01
Località: Lucca

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da maveloth »

mmm non so... ma te lo fa solo con una specifica scheda o con tutte le schede??

Maveloth

P.S. grazie dei ringraziamenti...
nina
Prode Principiante
Messaggi: 18
Iscrizione: martedì 26 maggio 2009, 19:15

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da nina »

ne ho provate altre ma niente
Avatar utente
maveloth
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 488
Iscrizione: lunedì 17 marzo 2008, 20:01
Località: Lucca

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da maveloth »

allora il problema è del lettore .. posta l'output di "lspci" e dimmi il modello del portatile

Maveloth
nina
Prode Principiante
Messaggi: 18
Iscrizione: martedì 26 maggio 2009, 19:15

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da nina »

00:00.0 Host bridge: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.1 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:00.3 System peripheral: Intel Corporation 82852/82855 GM/GME/PM/GMV Processor to I/O Controller (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
00:02.1 Display controller: Intel Corporation 82852/855GM Integrated Graphics Device (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
01:03.0 CardBus bridge: O2 Micro, Inc. OZ711M1/MC1 4-in-1 MemoryCardBus Controller (rev 20)
01:03.1 CardBus bridge: O2 Micro, Inc. OZ711M1/MC1 4-in-1 MemoryCardBus Controller (rev 20)
01:03.2 System peripheral: O2 Micro, Inc. OZ711Mx 4-in-1 MemoryCardBus Accelerator
01:07.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
01:0a.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
01:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)



modello notebook:Fujitsu siemens Amilo
Avatar utente
maveloth
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 488
Iscrizione: lunedì 17 marzo 2008, 20:01
Località: Lucca

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da maveloth »

non prenderlo come un rimprovero ma i risultati degli output mettili dentro il tag code altrimenti non ci si capisce nulla....
comunque ora vedo ... che manca il modello del portatile Amilo è la serie ce ne sono un po...

Maveloth
nina
Prode Principiante
Messaggi: 18
Iscrizione: martedì 26 maggio 2009, 19:15

[Risolto] Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da nina »

amilo M1405 dovrebbe essere il modello
Avatar utente
maveloth
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 488
Iscrizione: lunedì 17 marzo 2008, 20:01
Località: Lucca

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da maveloth »

pare che è il kernel che non ha un modulo per quel modello di lettore, comunque ci dovrebbe essere un pacchetto che lo fa funzionare. mi dovresti dire che versione di ubuntu stai usando

Maveloth
nina
Prode Principiante
Messaggi: 18
Iscrizione: martedì 26 maggio 2009, 19:15

Re: [Usb] hard disk esterno toshiba non riconosciuto da ubuntu.che fare?

Messaggio da nina »

la 9.04
Scrivi risposta

Ritorna a “Driver e periferiche”

Chi c’è in linea

Visualizzano questa sezione: Google [Bot] e 9 ospiti