Pagina 1 di 1
Errori nell'hard disk ATA
Inviato: giovedì 16 luglio 2009, 20:54
da Johnny B Good
Ciao a tutti, ho avviato la live Parted Magic per fare un controllo sui miei dischi che ultimamente facevano un po' di capricci e mi ha trovato questi errori per il mio hard disk ata
Codice: Seleziona tutto
Complete error log:
SMART Error Log Version: 1
Warning: ATA error count 10147 inconsistent with error log pointer 5
ATA Error Count: 10147 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 10147 occurred at disk power-on lifetime: 4684 hours (195 days + 4 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 0f 10 04 e2 Error: ICRC, ABRT at LBA = 0x0204100f = 33820687
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 0f 10 04 e2 08 00:05:52.816 READ DMA
c8 00 80 8f 0f 04 e2 08 00:05:52.816 READ DMA
c8 00 80 0f 0f 04 e2 08 00:05:52.816 READ DMA
c8 00 80 8f 0e 04 e2 08 00:05:52.816 READ DMA
c8 00 80 0f 0e 04 e2 08 00:05:52.816 READ DMA
Error 10146 occurred at disk power-on lifetime: 4674 hours (194 days + 18 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:04:45.136 READ DMA
f8 00 00 00 00 00 e0 08 00:04:45.104 READ NATIVE MAX ADDRESS
ec 00 00 00 00 00 a0 0a 00:04:45.088 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 00:04:45.088 SET FEATURES [Set transfer mode]
f8 00 00 00 00 00 e0 08 00:04:45.088 READ NATIVE MAX ADDRESS
Error 10145 occurred at disk power-on lifetime: 4671 hours (194 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:04:45.504 READ DMA
f8 00 00 00 00 00 e0 08 00:04:45.488 READ NATIVE MAX ADDRESS
ec 00 00 00 00 00 a0 0a 00:04:45.488 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 00:04:45.472 SET FEATURES [Set transfer mode]
f8 00 00 00 00 00 e0 08 00:04:45.472 READ NATIVE MAX ADDRESS
Error 10144 occurred at disk power-on lifetime: 4671 hours (194 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:04:45.296 READ DMA
f8 00 00 00 00 00 e0 08 00:04:45.264 READ NATIVE MAX ADDRESS
ec 00 00 00 00 00 a0 0a 00:04:45.264 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 00:04:45.248 SET FEATURES [Set transfer mode]
f8 00 00 00 00 00 e0 08 00:04:45.248 READ NATIVE MAX ADDRESS
Error 10143 occurred at disk power-on lifetime: 4667 hours (194 days + 11 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 8f de 7c e5 Error: ICRC, ABRT at LBA = 0x057cde8f = 92069519
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 8f de 7c e5 08 03:55:39.344 READ DMA
f8 00 00 00 00 00 e0 08 03:55:39.328 READ NATIVE MAX ADDRESS
ec 00 00 00 00 00 a0 0a 03:55:39.328 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 03:55:39.312 SET FEATURES [Set transfer mode]
f8 00 00 00 00 00 e0 08 03:55:39.312 READ NATIVE MAX ADDRESS
io sinceramente non so cosa voglia dire, ditemi soltanto per favore se si puo' fare qualcosa
Grazie mille
Re: Errori nell'hard disk ATA
Inviato: giovedì 16 luglio 2009, 21:12
da il_muflone
sono errori tutti riferiti più o meno allo stesso periodo ma non si sa se siano vecchi o recenti perché l'hdd misura il tempo in ore di utilizzo.
installa gsmartcontrol e avvia da quello un controllo del disco mediante smart (va bene pure quello rapido da 3 minuti)
quindi consulta il nuovo log e osserva il numero di ore, se oscilla tra 4700 ore allora gli errori di sopra sono recenti e dovresti pensare seriamente ad un backup urgente.
se l'orario del nuovo test riporta un numero di ore molto superiore, ad esempio 5000, 6000 allora quegli errori sono abbastanza vecchi, può essere che un certo giorno tu abbia avuto problemi al disco che si sono risolti da soli.
nello stesso programma troverai anche altre informazioni utili a decifrare gli errori
che non passi un messaggio fuorviante: gli errori smart sono errori registrati dal disco stesso, non può essersi sbagliato il sistema operativo.
ciao
Re: Errori nell'hard disk ATA
Inviato: giovedì 16 luglio 2009, 21:41
da Johnny B Good
ti ringrazio molto, il test che avevo fatto sul livecd era stato fatto proprio con gsmartcontrol; ora nel dubbio l'ho installato anche su ubuntu e ho fatto il test. Nonostante dice "
Test result: test completed without errors" (il Short self-test), nella scheda Error Log vedo comunque degli errori:
Codice: Seleziona tutto
Complete error log:
SMART Error Log Version: 1
Warning: ATA error count 10147 inconsistent with error log pointer 5
ATA Error Count: 10147 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 10147 occurred at disk power-on lifetime: 4684 hours (195 days + 4 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 0f 10 04 e2 Error: ICRC, ABRT at LBA = 0x0204100f = 33820687
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 0f 10 04 e2 08 00:05:52.816 READ DMA
c8 00 80 8f 0f 04 e2 08 00:05:52.816 READ DMA
c8 00 80 0f 0f 04 e2 08 00:05:52.816 READ DMA
c8 00 80 8f 0e 04 e2 08 00:05:52.816 READ DMA
c8 00 80 0f 0e 04 e2 08 00:05:52.816 READ DMA
Error 10146 occurred at disk power-on lifetime: 4674 hours (194 days + 18 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:04:45.136 READ DMA
f8 00 00 00 00 00 e0 08 00:04:45.104 READ NATIVE MAX ADDRESS
ec 00 00 00 00 00 a0 0a 00:04:45.088 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 00:04:45.088 SET FEATURES [Set transfer mode]
f8 00 00 00 00 00 e0 08 00:04:45.088 READ NATIVE MAX ADDRESS
Error 10145 occurred at disk power-on lifetime: 4671 hours (194 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:04:45.504 READ DMA
f8 00 00 00 00 00 e0 08 00:04:45.488 READ NATIVE MAX ADDRESS
ec 00 00 00 00 00 a0 0a 00:04:45.488 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 00:04:45.472 SET FEATURES [Set transfer mode]
f8 00 00 00 00 00 e0 08 00:04:45.472 READ NATIVE MAX ADDRESS
Error 10144 occurred at disk power-on lifetime: 4671 hours (194 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:04:45.296 READ DMA
f8 00 00 00 00 00 e0 08 00:04:45.264 READ NATIVE MAX ADDRESS
ec 00 00 00 00 00 a0 0a 00:04:45.264 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 00:04:45.248 SET FEATURES [Set transfer mode]
f8 00 00 00 00 00 e0 08 00:04:45.248 READ NATIVE MAX ADDRESS
Error 10143 occurred at disk power-on lifetime: 4667 hours (194 days + 11 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 8f de 7c e5 Error: ICRC, ABRT at LBA = 0x057cde8f = 92069519
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 8f de 7c e5 08 03:55:39.344 READ DMA
f8 00 00 00 00 00 e0 08 03:55:39.328 READ NATIVE MAX ADDRESS
ec 00 00 00 00 00 a0 0a 03:55:39.328 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 03:55:39.312 SET FEATURES [Set transfer mode]
f8 00 00 00 00 00 e0 08 03:55:39.312 READ NATIVE MAX ADDRESS
Penso comunque di aver identificato l'origine di questi errori, ovvero spegnimenti drastici che sono stato obbligato a fare a cusa di un rumore strano alla ventola del processore...In ogni caso se il disco è danneggiato irrimediabilmente non è un grosso problema, ne compro uno nuovo, sata, e risolvo il problema...
Grazie ancora.
Re: Errori nell'hard disk ATA
Inviato: giovedì 16 luglio 2009, 21:51
da il_muflone
oltre a completed without error dice anche il lifetime hours
se oscilla a circa 4700 sono errori nuovi
Re: Errori nell'hard disk ATA
Inviato: venerdì 17 luglio 2009, 12:23
da Johnny B Good
ah ok, il risultato del test è questo
Codice: Seleziona tutto
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Maxtor DiamondMax Plus 9 family
Device Model: Maxtor 6Y080L0
Serial Number: Y25MSZQC
Firmware Version: YAR41BW0
User Capacity: 81,964,302,336 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Fri Jul 17 12:19:37 2009 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 241) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 37) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 216 214 063 Pre-fail Always - 10841
4 Start_Stop_Count 0x0032 252 252 000 Old_age Always - 2071
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always - 0
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0
8 Seek_Time_Performance 0x0027 253 249 187 Pre-fail Always - 37937
9 Power_On_Minutes 0x0032 238 238 000 Old_age Always - 848h+00m
10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0
11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 248 248 000 Old_age Always - 2129
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always - 26
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 1091
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline - 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0008 001 001 000 Old_age Offline - 9398
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0
201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 0
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0
207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0
208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0
209 Offline_Seek_Performnce 0x0024 185 185 000 Old_age Offline - 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0
SMART Error Log Version: 1
Warning: ATA error count 10147 inconsistent with error log pointer 5
ATA Error Count: 10147 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 10147 occurred at disk power-on lifetime: 4684 hours (195 days + 4 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 0f 10 04 e2 Error: ICRC, ABRT at LBA = 0x0204100f = 33820687
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 80 0f 10 04 e2 08 00:05:52.816 READ DMA
c8 00 80 8f 0f 04 e2 08 00:05:52.816 READ DMA
c8 00 80 0f 0f 04 e2 08 00:05:52.816 READ DMA
c8 00 80 8f 0e 04 e2 08 00:05:52.816 READ DMA
c8 00 80 0f 0e 04 e2 08 00:05:52.816 READ DMA
Error 10146 occurred at disk power-on lifetime: 4674 hours (194 days + 18 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:04:45.136 READ DMA
f8 00 00 00 00 00 e0 08 00:04:45.104 READ NATIVE MAX ADDRESS
ec 00 00 00 00 00 a0 0a 00:04:45.088 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 00:04:45.088 SET FEATURES [Set transfer mode]
f8 00 00 00 00 00 e0 08 00:04:45.088 READ NATIVE MAX ADDRESS
Error 10145 occurred at disk power-on lifetime: 4671 hours (194 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:04:45.504 READ DMA
f8 00 00 00 00 00 e0 08 00:04:45.488 READ NATIVE MAX ADDRESS
ec 00 00 00 00 00 a0 0a 00:04:45.488 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 00:04:45.472 SET FEATURES [Set transfer mode]
f8 00 00 00 00 00 e0 08 00:04:45.472 READ NATIVE MAX ADDRESS
Error 10144 occurred at disk power-on lifetime: 4671 hours (194 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 e0 Error: ICRC, ABRT at LBA = 0x00000000 = 0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 00 00 00 e0 08 00:04:45.296 READ DMA
f8 00 00 00 00 00 e0 08 00:04:45.264 READ NATIVE MAX ADDRESS
ec 00 00 00 00 00 a0 0a 00:04:45.264 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 00:04:45.248 SET FEATURES [Set transfer mode]
f8 00 00 00 00 00 e0 08 00:04:45.248 READ NATIVE MAX ADDRESS
Error 10143 occurred at disk power-on lifetime: 4667 hours (194 days + 11 hours)
When the command that caused the error occurred, the device was in an unknown state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 8f de 7c e5 Error: ICRC, ABRT at LBA = 0x057cde8f = 92069519
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 8f de 7c e5 08 03:55:39.344 READ DMA
f8 00 00 00 00 00 e0 08 03:55:39.328 READ NATIVE MAX ADDRESS
ec 00 00 00 00 00 a0 0a 03:55:39.328 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 0a 03:55:39.312 SET FEATURES [Set transfer mode]
f8 00 00 00 00 00 e0 08 03:55:39.312 READ NATIVE MAX ADDRESS
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 4891 -
# 2 Short offline Completed without error 00% 4887 -
# 3 Short offline Completed without error 00% 4886 -
# 4 Short offline Completed without error 00% 4886 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
quindi da quanto posso dedurre dalla parte finale dove dice
Codice: Seleziona tutto
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 4891 -
# 2 Short offline Completed without error 00% 4887 -
# 3 Short offline Completed without error 00% 4886 -
# 4 Short offline Completed without error 00% 4886 -
le ore sono 4891. Rientra nei numeri vicini a 4700 o no? Se sono errori nuovi, che differenza fa?
Perdonami ma come avrai capito non sono molto pratico...
Grazie ancora
Re: Errori nell'hard disk ATA
Inviato: venerdì 17 luglio 2009, 12:32
da il_muflone
il test serviva solo a capire se si trattasse di errori di 1-2-3 anni fa di cui non ti frega più tanto, ma evidentemente non è così, quindi sono errori abbastanza recenti
la maggior parte sembrano errori di lettura
è possibile che il disco ti abbandoni, di più non si capisce da quei messaggi
ciao
Re: Errori nell'hard disk ATA
Inviato: venerdì 17 luglio 2009, 16:09
da Johnny B Good
ok, grazie mille. appena torno dalle vacanze mi compro un nuovo hard disk, sperando che questa resista ancora per le prossime 10, 15 ore massimo di vita