Pagina 3 di 3
Re: temperature da panico! -- karmic & lucid
Inviato: lunedì 28 giugno 2010, 15:30
da Alka-Seltzer PLUS
Hai installato la sensors-applet da mettere sul pannello superiore ? Così puoi anche monitoreare la velocità delle ventole
Che computer hai ? Da quanto lo utilizzi ? Potrebbe anche essere che devi darci una spolverata

Re: temperature da panico! -- karmic & lucid
Inviato: lunedì 28 giugno 2010, 16:09
da TheDarker
Ho un acer aspire 5536, ubuntu 10.4 32 bit, è nuovo di settembre e ubuntu lo ho da un mesetto scarso adesso che ho installato l'applet sono a 55 col primo e 62 con il secondo... mi pare che siano alte...
Re: temperature da panico! -- karmic & lucid
Inviato: lunedì 28 giugno 2010, 18:10
da Alka-Seltzer PLUS
Hai provato ad installare i driver ATI come da guida ?
http://forum.ubuntu-it.org/viewtopic.php?t=155477
Re: temperature da panico! -- karmic & lucid
Inviato: lunedì 28 giugno 2010, 19:10
da TheDarker
quel maledetto driver..... l'ho tolto perchè non mi faceva andare compiz, ma mi sn documentato e ho visto che le temperature dei processori AMD Athlon 64 X2 sono di default sui 60-65 gradi... e allora mi chiedo se abbia sbagliato a mettere ubuntu 32 bit... conviene mettere un 64? successivamente con il sensors ke mi hai dato ho notato che appena attivo un video qualsiasi su youtube (condizioni + di 720p) la temperaura di primo processore da 55 sale a 65 in 2 sec

(tempo dell'aggiornamento di sensors)
boh.. rimango del parere che 60 sia troppo...
Re: temperature da panico! -- karmic & lucid
Inviato: lunedì 28 giugno 2010, 19:38
da Alka-Seltzer PLUS
Anche io avevo problemi con le temperature con la 9.10 a 64 bit visualizzando filmati in flash.
Ora con la 10.04 ed i driver open non ne ho più
Viaggio attorno ai 50 °C a pieno schermo ( ma fai conto che ho un fisso ... )
Re: temperature da panico! -- karmic & lucid
Inviato: lunedì 28 giugno 2010, 21:42
da TheDarker
si, ma il fisso non ha nessun problema di raffreddamento... :P ma la mia domanda era, ora lo ho a 32 bit, avendo un amd athlon 64 x2 mi conviene installarlo a 64? e se fosse devo piallarlo o posso fare un upgrada?
Re: temperature da panico! -- karmic & lucid
Inviato: martedì 29 giugno 2010, 16:27
da pgallir
>:( i ocontinuo a sbattere la testa... però nel tentativo di capire cosa non andava, ho installato acpi. bene, se lancio
Codice: Seleziona tutto
jaky@jaky-laptop:~$ acpi -V
Battery 0: Full, 100%
Battery 0: design capacity 622 mAh, last full capacity 544 mAh = 87%
Adapter 0: on-line
Thermal 0: active, 57.0 degrees C
Thermal 0: trip point 0 switches to mode critical at temperature 85.0 degrees C
Thermal 0: trip point 1 switches to mode passive at temperature 95.0 degrees C
Thermal 0: trip point 2 switches to mode active at temperature 71.0 degrees C
Thermal 0: trip point 3 switches to mode active at temperature 55.0 degrees C
Thermal 1: ok, 26.8 degrees C
Thermal 1: trip point 0 switches to mode critical at temperature 127.0 degrees C
Cooling 0: LCD 0 of 15
Cooling 1: Processor 0 of 10
Cooling 2: Processor 0 of 10
Cooling 3: Processor 0 of 10
Cooling 4: Processor 0 of 10
Cooling 5: Processor 0 of 10
Cooling 6: Processor 0 of 10
Cooling 7: Processor 0 of 10
Cooling 8: Processor 0 of 10
Cooling 9: Fan 0 of 1
Cooling 10: Fan 1 of 1
jaky@jaky-laptop:~$
sogno o son desto? che vuol dire? che ha diversi gradi di raffreddamento per 55 70 85 95 e 127 gradi?? sempre se ho capito bene: cosa me ne faccio? da 85 in poi il pc è bello e defunto! non sarà che il problema è quello? se ho detto una bischerata sentitevi liberi di fustigarmi verbalmente.
Re: temperature da panico! -- karmic & lucid
Inviato: martedì 29 giugno 2010, 16:58
da pgallir
altra news....
grazie Alka-Seltzer PLUS, per via indiretta, al post
http://forum.ubuntu-it.org/viewtopic.php?t=389474 suggerisci di seguire qui
http://wiki.ubuntu-it.org/Amministrazio ... lmsensors)
e li ci sta la voce "Configurazione manuale".
seguendo quelle indicazioni ottengo...
Codice: Seleziona tutto
jaky@jaky-laptop:~$ sudo ./sensors-detect
# sensors-detect revision $Revision$
# System: Dell Inc. Studio 1557
# Board: Dell Inc. 0KM426
This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.
Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no):
Silicon Integrated Systems SIS5595... No
VIA VT82C686 Integrated Sensors... No
VIA VT8231 Integrated Sensors... No
AMD K8 thermal sensors... No
AMD Family 10h thermal sensors... No
AMD Family 11h thermal sensors... No
Intel Core family thermal sensor... Success!
(driver `coretemp')
Intel Atom thermal sensor... No
Intel AMB FB-DIMM thermal sensor... No
VIA C7 thermal sensor... No
VIA Nano thermal sensor... No
Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no):
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'... No
Trying family `SMSC'... No
Trying family `VIA/Winbond/Nuvoton/Fintek'... No
Trying family `ITE'... No
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'... Yes
Found unknown chip with ID 0x8502
Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no):
Probing for `IPMI BMC KCS' at 0xca0... No
Probing for `IPMI BMC SMIC' at 0xca8... No
Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (YES/no):
Probing for `National Semiconductor LM78' at 0x290... No
Probing for `National Semiconductor LM79' at 0x290... No
Probing for `Winbond W83781D' at 0x290... No
Probing for `Winbond W83782D' at 0x290... No
Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no):
Using driver `i2c-i801' for device 0000:00:1f.3: Intel 3400/5 Series (PCH)
Module i2c-i801 loaded successfully.
Now follows a summary of the probes I have just done.
Just press ENTER to continue:
Driver `coretemp':
* Chip `Intel Core family thermal sensor' (confidence: 9)
Do you want to generate /etc/sysconfig/lm_sensors? (yes/NO):
To load everything that is needed, add this to one of the system
initialization scripts (e.g. /etc/rc.d/rc.local):
#----cut here----
# Chip drivers
modprobe coretemp
/usr/bin/sensors -s
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones! You really
should try these commands right now to make sure everything is
working properly. Monitoring programs won't work until the needed
modules are loaded.
Unloading i2c-i801... OK
jaky@jaky-laptop:~$
e mo?? che dovrei fare?
ottengo infatti
#----cut here----
# Chip drivers
modprobe coretemp
/usr/bin/sensors -s
#----cut here----
e non qualcosa tipo
#----cut here----
# I2C adapter drivers
i2c-viapro
i2c-isa
# I2C chip drivers
eeprom
it87
#----cut here----
ad ogni modo un passetto in avanti è stato fatto. ora riconosce più sneosri di prima!
Codice: Seleziona tutto
jaky@jaky-laptop:~$ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1: +26.8°C (crit = +127.0°C)
temp2: +60.0°C (crit = +85.0°C)
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +58.0°C (high = +84.0°C, crit = +100.0°C)
coretemp-isa-0001
Adapter: ISA adapter
Core 1: +56.0°C (high = +84.0°C, crit = +100.0°C)
coretemp-isa-0002
Adapter: ISA adapter
Core 2: +61.0°C (high = +84.0°C, crit = +100.0°C)
coretemp-isa-0003
Adapter: ISA adapter
Core 3: +55.0°C (high = +84.0°C, crit = +100.0°C)
coretemp-isa-0004
Adapter: ISA adapter
Core 4: +58.0°C (high = +84.0°C, crit = +100.0°C)
coretemp-isa-0005
Adapter: ISA adapter
Core 5: +56.0°C (high = +84.0°C, crit = +100.0°C)
coretemp-isa-0006
Adapter: ISA adapter
Core 6: +61.0°C (high = +84.0°C, crit = +100.0°C)
coretemp-isa-0007
Adapter: ISA adapter
Core 7: +56.0°C (high = +84.0°C, crit = +100.0°C)
jaky@jaky-laptop:~$
Re: temperature da panico! -- karmic & lucid
Inviato: giovedì 1 luglio 2010, 10:55
da pgallir
una buona notizia ed una grrrrrrrrrrrrrrrrrrrrrrrrrrr...............
ho fatto un upgrade e mi ha scaricato il kernel nuovo, e ora - a parte che non mi va più l'audio con il nuovo kernel, ma chiudo qui perchè sarebbe (ot).. -
Codice: Seleziona tutto
jaky@jaky-laptop:~$ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1: +26.8°C (crit = +127.0°C)
temp2: +57.0°C (crit = +85.0°C)
jaky@jaky-laptop:~$
la buona notizia la vedete da voi: il mio pc non va più in temperatura di ebollizione. Questo, a patto che io non decida di guardarmi un film... li mi sono accorto che la temperatura è funzione della dimensione dello schermo dove proietto il filmato. E a schermo intero va tranquillo tranquillo ad 80 gradi... sicchè (sigh) per ora ho uno schermo full HD con tanto di scheda grafica dedicata per una mazza di niente....
qualcuno sa dirmi a che santo devo votarmi?
Re: temperature da panico! -- karmic & lucid
Inviato: lunedì 12 luglio 2010, 12:44
da pgallir
bene, risolto audio, uso di nuovo i driver ati aggiornati e uso il flash giusto.
Le temperature sono sempre alte. Mi sono però accorto che uso libc6-i386 e non la libc6-i686 (che però mi viene detto da apt-get che è obsoleta).
Allora ho installato la eglibc-source, perchè avevo letto qui
http://www.ubuntuupdates.org/packages/show/202687 che è l'head package... qualcuno mi può fermare se sto prendendo un abbaglio??