[Risolto] Installare Stampante HP B109n su Kubuntu 10.04

Riconoscimento, installazione e configurazione delle periferiche.
dapinna
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 268
Iscrizione: domenica 13 novembre 2005, 20:26
Desktop: KDE
Distribuzione: KUbuntu 16.04 LTS ( x86_64)
Sesso: Maschile
Località: Sassari
Contatti:

[Risolto] Installare Stampante HP B109n su Kubuntu 10.04

Messaggio da dapinna »

Salve a tutti.

Ho una stampante HP B109n, che funziona sia con USB che Wifi
So che qualcuno è riuscito ad installarla e in effetti la procedura è semplice e ho seguito
le indicazioni che ho trovato nel sito HP, cioè ho scaricato il file hplip-3.10.5.run ed installato
usando il comando

Codice: Seleziona tutto

run hplip-3.10.5.run
Rispondo ad alcune domandi, inserisco la password e vedo che inizia a scaricare dei pacchetti di alcune dipendenze che mancavano
quindi ricontrolla le dipendenze e dice "tutto ok".

Ma alla fine riposta un errore:
hplip-3.10.5.run
Ho ripetuto il comando alcune volte, anche cancellando la sotto-cartella che crea, ma l'unica differenze è che le dipendenze
sono già a posto al primo controllo.

Per completezza allego i risultati del comando:

Codice: Seleziona tutto

sh hplip-3.10.5.run 
Creating directory hplip-3.10.5
Verifying archive integrity... All good.
Uncompressing HPLIP 3.10.5 Self Extracting Archive....................

   [cut di un mare di puntini]

HP Linux Imaging and Printing System (ver. 3.10.5)
HPLIP Installer ver. 5.1

Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.

Installer log saved in: hplip-install_Tue-22-Jun-2010_23:36:43.log

/
note: Defaults for each question are maked with a '*'. Press <enter> to accept the default.


INSTALLATION MODE
-----------------
Automatic mode will install the full HPLIP solution with the most common options.
Custom mode allows you to choose installation options to fit specific requirements.

Please choose the installation mode (a=automatic*, c=custom, q=quit) : 

Initializing. Please wait...
 

INTRODUCTION
------------
This installer will install HPLIP version 3.10.5 on your computer.
Please close any running package management systems now (YaST, Adept, Synaptic, Up2date, etc).
 

DISTRO/OS CONFIRMATION
----------------------
Distro appears to be Ubuntu 10.04.

Is "Ubuntu 10.04" your correct distro/OS and version (y=yes*, n=no, q=quit) ? 


ENTER USER PASSWORD
-------------------
Please enter the user (daniele)'s password: 
Password accepted


INSTALLATION NOTES
------------------
Enable the universe/multiverse repositories. Also be sure you are using the Ubuntu "Main" Repositories. See: https://help.ubuntu.com/community/Repositories/Ubuntu for more information.  Disable the CD-ROM/DVD source if you do not have the Ubuntu installation media inserted in the drive.  During the install process you will be added to the lp group, please quit the installer before the setup stage, log out, log back in, and run hp-setup to complete the install.

Please read the installation notes. Press <enter> to continue or 'q' to quit: 


RUNNING PRE-INSTALL COMMANDS
----------------------------
OK


CHECKING FOR NETWORK CONNECTION
-------------------------------
Network connection present.


RUNNING PRE-PACKAGE COMMANDS
----------------------------
sudo dpkg --configure -a (Pre-depend step 1)
sudo apt-get install --yes --force-yes -f (Pre-depend step 2)
sudo aptitude update (Pre-depend step 3)
OK


DEPENDENCY AND CONFLICT RESOLUTION
----------------------------------
warning: A previous install of HPLIP is installed and/or running.
sudo apt-get remove --assume-yes hplip hpijs hplip-cups hplip-data libhpmud0 foomatic-db-hpijs (Removing old HPLIP version)
warning: HPLIP removal failed. The previous install may have been installed using a tarball or this installer.
warning: Continuing to run installer - this installation should overwrite the previous one.


RUNNING POST-PACKAGE COMMANDS
-----------------------------
OK


RE-CHECKING DEPENDENCIES
------------------------
OK


PRE-BUILD COMMANDS
------------------
OK


BUILD AND INSTALL
-----------------
Running './configure --with-hpppddir=/usr/share/ppd/HP --prefix=/usr --enable-udev-acl-rules --enable-qt4 --enable-doc-build --disable-cups-ppd-install --disable-foomatic-drv-install --disable-foomatic-ppd-install --disable-hpijs-install --disable-policykit --enable-cups-drv-install --enable-hpcups-install --enable-network-build --enable-dbus-build --enable-scan-build --enable-fax-build'
Please wait, this may take several minutes...
Command completed successfully.

Running 'make clean'
Please wait, this may take several minutes...
Command completed successfully.

Running 'make'
Please wait, this may take sjavascript:void(0);everal minutes...

error: 'make' command failed with status code 2

Se poi dovesse servire anche: lsusb

Codice: Seleziona tutto

lsusb
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 041e:4028 Creative Technology, Ltd Vista Plus cam [VF0090]
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 004: ID 03f0:7b11 Hewlett-Packard 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
daniele@pcdan-linux:/media/disk-1/Software/Linux/Driver/Stampante HP b109n$ 

Come posso risolvere?
Ovviamente mi accontenterei della stampa da USB ma cmq avrei problemi con il "piccolino" con Kubuntu per Netbook
e quello voglio collegarlo con il WiFi :-)

Ringrazio Anticipatamente per le Risposte
Ultima modifica di dapinna il mercoledì 23 giugno 2010, 1:40, modificato 1 volta in totale.
dapinna
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 268
Iscrizione: domenica 13 novembre 2005, 20:26
Desktop: KDE
Distribuzione: KUbuntu 16.04 LTS ( x86_64)
Sesso: Maschile
Località: Sassari
Contatti:

Re: Installare Stampante HP B109n su Kubuntu 10.04

Messaggio da dapinna »

mi rispondo da solo, dato che ho risolto, sperando che possa servire a qualcun altro :-)

Ho installato hplip e hplib-gui da repository

Ho dato il comando hp-setup e seguito la procedura.

ad un certo punto da un msg di errore e vedo una casella gialla che invita a sfogliare per selezionare il ppd corretto.
Li non ho trovato il ppd della stampante, ma è presente nella cartella che si è creata durante il tentativo di installazione con il file scaricato da HP

Per ora è solo USB ma non dovrebbe essere un problema impostarla via wireless
Scrivi risposta

Ritorna a “Driver e periferiche”

Chi c’è in linea

Visualizzano questa sezione: 0 utenti iscritti e 4 ospiti