Ciao Pier,
io ho risolto seguendo step by step questa utilissima guida:
http://www.halibutdepot.org/how_to_buil ... ntu_lucid/
Se anche tu hai una scheda wireless RT3090 (e se usi un EEEPC 1001HA è questa) seguendo la guida potrai risvegliarla.
Inizialmente avevo provato con l'ultima versione del device scaricabile dal sito ufficiale dopo aver inseriti alcuni dati (
http://www.ralinktech.com/support.php?s=2). Ma, forse per incompatibilità tra patch e versione, non funzionava.
Quindi ho seguito in todo la procedura ed installato il precedente drive (la versione 2.3.1.3 del 8 febbraio 2010) e si connette benissimo.
Puoi anche provare con una procedura già pronta al link:
http://stat.case.edu/~jrt32/how_to_buil ... a1_all.deb (che a me non funzionava in quanto rilevava che la mia versione era più recente).
Un ultima cosa prima di salutarti: facendo un iwconfig il risultato è questo:
lo no wireless extensions.
ra0 Ralink STA ESSID:"TSUNAMI_WIRELESS" Nickname:"RT2860STA"
Mode:Managed Frequency=2.437 GHz Access Point: 00:1B:2F:EE:D4:0A
Bit Rate=65 Mb/s
RTS thr:off Fragment thr:off
Link Quality=100/100 Signal level:-47 dBm Noise level:-83 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
eth0 no wireless extensions.
M'inquieta il fatto che la wlan0 è scomparsa... (???) BHO...
Questo il risultato del comando lspci
00:00.0 Host bridge: Intel Corporation Mobile 945GME Express Memory Controller Hub (rev 03)
00:02.0 VGA compatible controller: Intel Corporation Mobile 945GME Express Integrated Graphics Controller (rev 03)
00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 02)
00:1c.3 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 4 (rev 02)
00:1d.0 USB Controller: Intel Corporation N10/ICH7 Family USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 02)
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 02)
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)
00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)
00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02)
01:00.0 Ethernet controller: Atheros Communications Atheros AR8132 / L1c Gigabit Ethernet Adapter (rev c0)
02:00.0 Network controller: RaLink RT3090 Wireless 802.11n 1T/1R PCIe
Good luck e se qualche guru potesse spiegarmi perchè non si vede la wlan0, garantisco un meraviglioso caffè in riva al mare.
Ciao.