[Supporto] porta IrDA integrata: problemi con ircp-tray
Inviato: mercoledì 11 agosto 2010, 23:29
Ciao a tutt@,
ho installato lucid su un acer aspire 5720 di un amico di cui non possiedo la documentazione.
Il portatile ha una porta infrarossi che il mio amico vuole usare per trasferire le foto dal cellulare.
Non so nulla dell'argomento perché non ho mai utilizzato questa tecnologia.
Ho letto la relativa documentazione della comunità e credo che il mio caso sia quello della porta integrata.
Innanzitutto non so come capire se entrambe le modalità SIR e FIR sono supportate.
Leggendo la documentazione mi è parso di capire che in genere i dispositivi le offrono entrambe, per cui ho seguito le indicazioni per entrambe.
Non so se la porta è abilitata nel BIOS, nel quale non c'è nessuna voce che la riguardi.
Ho installato irda-utils e setserial.
Ho eseguito i comandi per la configurazione della FIR e per le configurazioni comuni.
Ho eseguito dmsg e ho trovato soltanto queste righe che mi sembra possano essere rilevanti
ma non corrispondono all'output indicato dalla guida
questo dmsg completo o almeno quello che sono riuscita a copiare
Non ho a disposizione un cellulare con infrarossi per testare la connessione.
Infine ho installato ircp-tray ma quando vado ad aprirlo mi dice:
Servizio irda non avviato!
È necessario modificare «/etc/default/irda-utils» e impostare la partenza all'avvio di irattach .
Altrimenti provare a digitare nel terminale:
"sudo irattach /dev/ttyS1 -s"
Leggere il manuale di irattach per maggiori informazioni.
Ircp Tray non sarà in grado di funzionare.
Ho fatto quanto indicato ma l'avviso ricompare, quindi immagino che sia un problema di riconoscimento o configurazione della porta.
Avete qualche suggerimento su come procedere?
Grazie
ho installato lucid su un acer aspire 5720 di un amico di cui non possiedo la documentazione.
Il portatile ha una porta infrarossi che il mio amico vuole usare per trasferire le foto dal cellulare.
Non so nulla dell'argomento perché non ho mai utilizzato questa tecnologia.
Ho letto la relativa documentazione della comunità e credo che il mio caso sia quello della porta integrata.
Innanzitutto non so come capire se entrambe le modalità SIR e FIR sono supportate.
Leggendo la documentazione mi è parso di capire che in genere i dispositivi le offrono entrambe, per cui ho seguito le indicazioni per entrambe.
Non so se la porta è abilitata nel BIOS, nel quale non c'è nessuna voce che la riguardi.
Ho installato irda-utils e setserial.
Ho eseguito i comandi per la configurazione della FIR e per le configurazioni comuni.
Ho eseguito dmsg e ho trovato soltanto queste righe che mi sembra possano essere rilevanti
Codice: Seleziona tutto
17.368228] irda_init()
[ 17.368240] NET: Registered protocol family 23
[ 17.371625] IrCOMM protocol (Dag Brattli)
questo dmsg completo o almeno quello che sono riuscita a copiare
Codice: Seleziona tutto
[ 0.742744] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
[ 0.742838] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
[ 0.742954] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[ 0.743158] ACPI Warning for \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, ACPI requires 4 (20090903/nspredef-336)
[ 0.752937] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.753079] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.753218] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.753357] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.753496] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 0.753637] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12)
[ 0.753775] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.753913] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12)
[ 0.754078] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.754087] vgaarb: loaded
[ 0.754223] SCSI subsystem initialized
[ 0.754271] libata version 3.00 loaded.
[ 0.754271] usbcore: registered new interface driver usbfs
[ 0.754271] usbcore: registered new interface driver hub
[ 0.754271] usbcore: registered new device driver usb
[ 0.754271] ACPI: WMI: Mapper loaded
[ 0.754271] PCI: Using ACPI for IRQ routing
[ 0.754271] NetLabel: Initializing
[ 0.754271] NetLabel: domain hash size = 128
[ 0.754271] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.754271] NetLabel: unlabeled traffic allowed by default
[ 0.754271] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.754271] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.760028] Switching to clocksource tsc
[ 0.762420] AppArmor: AppArmor Filesystem Enabled
[ 0.762430] pnp: PnP ACPI init
[ 0.762440] ACPI: bus type pnp registered
[ 0.763545] pnp 00:01: io resource (0x164e-0x164f) overlaps 0000:00:1c.3 BAR 13 (0x1000-0x1fff), disabling
[ 0.784199] pnp: PnP ACPI: found 10 devices
[ 0.784202] ACPI: ACPI bus type pnp unregistered
[ 0.784205] PnPBIOS: Disabled by ACPI PNP
[ 0.784217] system 00:01: ioport range 0x600-0x60f has been reserved
[ 0.784220] system 00:01: ioport range 0x610-0x610 has been reserved
[ 0.784224] system 00:01: ioport range 0x800-0x80f has been reserved
[ 0.784227] system 00:01: ioport range 0x810-0x817 has been reserved
[ 0.784230] system 00:01: ioport range 0x400-0x47f has been reserved
[ 0.784233] system 00:01: ioport range 0x500-0x53f has been reserved
[ 0.784237] system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.784241] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.784244] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved
[ 0.784248] system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved
[ 0.784251] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved
[ 0.784254] system 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved
[ 0.784258] system 00:01: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.784261] system 00:01: iomem range 0x32000000-0x320000ff could not be reserved
[ 0.818974] pci 0000:01:00.0: BAR 6: no parent found for of device [0xfffe0000-0xffffffff]
[ 0.819044] pci 0000:01:00.0: BAR 6: can't allocate mem resource [0x90000000-0x8fffffff]
[ 0.819048] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.819051] pci 0000:00:01.0: IO window: 0x5000-0x5fff
[ 0.819056] pci 0000:00:01.0: MEM window: 0x90000000-0x92ffffff
[ 0.819060] pci 0000:00:01.0: PREFETCH window: 0x00000080000000-0x0000008fffffff
[ 0.819066] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.819070] pci 0000:00:1c.0: IO window: 0x4000-0x4fff
[ 0.819078] pci 0000:00:1c.0: MEM window: 0x9a300000-0x9b2fffff
[ 0.819083] pci 0000:00:1c.0: PREFETCH window: 0x00000093000000-0x00000093ffffff
[ 0.819093] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:04
[ 0.819097] pci 0000:00:1c.1: IO window: 0x3000-0x3fff
[ 0.819104] pci 0000:00:1c.1: MEM window: 0x99300000-0x9a2fffff
[ 0.819110] pci 0000:00:1c.1: PREFETCH window: 0x00000094000000-0x00000094ffffff
[ 0.819119] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:05
[ 0.819123] pci 0000:00:1c.2: IO window: 0x2000-0x2fff
[ 0.819131] pci 0000:00:1c.2: MEM window: 0x98200000-0x992fffff
[ 0.819137] pci 0000:00:1c.2: PREFETCH window: 0x00000095000000-0x00000095ffffff
[ 0.819146] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:06
[ 0.819150] pci 0000:00:1c.3: IO window: 0x1000-0x1fff
[ 0.819157] pci 0000:00:1c.3: MEM window: 0x97100000-0x981fffff
[ 0.819163] pci 0000:00:1c.3: PREFETCH window: 0x00000096000000-0x00000096ffffff
[ 0.819173] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:07
[ 0.819176] pci 0000:00:1e.0: IO window: disabled
[ 0.819183] pci 0000:00:1e.0: MEM window: 0x97000000-0x970fffff
[ 0.819188] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.819204] alloc irq_desc for 16 on node -1
[ 0.819206] alloc kstat_irqs on node -1
[ 0.819212] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.819217] pci 0000:00:01.0: setting latency timer to 64
[ 0.819228] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.819234] pci 0000:00:1c.0: setting latency timer to 64
[ 0.819246] alloc irq_desc for 17 on node -1
[ 0.819248] alloc kstat_irqs on node -1
[ 0.819252] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.819258] pci 0000:00:1c.1: setting latency timer to 64
[ 0.819271] alloc irq_desc for 18 on node -1
[ 0.819273] alloc kstat_irqs on node -1
[ 0.819278] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.819283] pci 0000:00:1c.2: setting latency timer to 64
[ 0.819295] alloc irq_desc for 19 on node -1
[ 0.819297] alloc kstat_irqs on node -1
[ 0.819301] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[ 0.819306] pci 0000:00:1c.3: setting latency timer to 64
[ 0.819316] pci 0000:00:1e.0: setting latency timer to 64
[ 0.819321] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.819324] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.819327] pci_bus 0000:01: resource 0 io: [0x5000-0x5fff]
[ 0.819330] pci_bus 0000:01: resource 1 mem: [0x90000000-0x92ffffff]
[ 0.819333] pci_bus 0000:01: resource 2 pref mem [0x80000000-0x8fffffff]
[ 0.819336] pci_bus 0000:02: resource 0 io: [0x4000-0x4fff]
[ 0.819338] pci_bus 0000:02: resource 1 mem: [0x9a300000-0x9b2fffff]
[ 0.819341] pci_bus 0000:02: resource 2 pref mem [0x93000000-0x93ffffff]
[ 0.819344] pci_bus 0000:04: resource 0 io: [0x3000-0x3fff]
[ 0.819347] pci_bus 0000:04: resource 1 mem: [0x99300000-0x9a2fffff]
[ 0.819350] pci_bus 0000:04: resource 2 pref mem [0x94000000-0x94ffffff]
[ 0.819353] pci_bus 0000:05: resource 0 io: [0x2000-0x2fff]
[ 0.819355] pci_bus 0000:05: resource 1 mem: [0x98200000-0x992fffff]
[ 0.819358] pci_bus 0000:05: resource 2 pref mem [0x95000000-0x95ffffff]
[ 0.819361] pci_bus 0000:06: resource 0 io: [0x1000-0x1fff]
[ 0.819364] pci_bus 0000:06: resource 1 mem: [0x97100000-0x981fffff]
[ 0.819367] pci_bus 0000:06: resource 2 pref mem [0x96000000-0x96ffffff]
[ 0.819370] pci_bus 0000:07: resource 1 mem: [0x97000000-0x970fffff]
[ 0.819372] pci_bus 0000:07: resource 3 io: [0x00-0xffff]
[ 0.819375] pci_bus 0000:07: resource 4 mem: [0x000000-0xffffffff]
[ 0.819410] NET: Registered protocol family 2
[ 0.819514] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.819888] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.820323] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.820523] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.820525] TCP reno registered
[ 0.820601] NET: Registered protocol family 1
[ 0.820982] pci 0000:01:00.0: Boot video device
[ 0.821197] cpufreq-nforce2: No nForce2 chipset.
[ 0.821227] Scanning for low memory corruption every 60 seconds
[ 0.821350] audit: initializing netlink socket (disabled)
[ 0.821361] type=2000 audit(1281541317.819:1): initialized
[ 0.832549] highmem bounce pool size: 64 pages
[ 0.832556] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.834310] VFS: Disk quotas dquot_6.5.2
[ 0.834379] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.835021] fuse init (API version 7.13)
[ 0.835117] msgmni has been set to 1705
[ 0.835343] alg: No test for stdrng (krng)
[ 0.835401] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.835405] io scheduler noop registered
[ 0.835408] io scheduler anticipatory registered
[ 0.835410] io scheduler deadline registered
[ 0.835455] io scheduler cfq registered (default)
[ 0.835629] alloc irq_desc for 24 on node -1
[ 0.835631] alloc kstat_irqs on node -1
[ 0.835640] pcieport 0000:00:01.0: irq 24 for MSI/MSI-X
[ 0.835647] pcieport 0000:00:01.0: setting latency timer to 64
[ 0.835801] alloc irq_desc for 25 on node -1
[ 0.835803] alloc kstat_irqs on node -1
[ 0.835813] pcieport 0000:00:1c.0: irq 25 for MSI/MSI-X
[ 0.835825] pcieport 0000:00:1c.0: setting latency timer to 64
[ 0.835999] alloc irq_desc for 26 on node -1
[ 0.836001] alloc kstat_irqs on node -1
[ 0.836012] pcieport 0000:00:1c.1: irq 26 for MSI/MSI-X
[ 0.836024] pcieport 0000:00:1c.1: setting latency timer to 64
[ 0.836195] alloc irq_desc for 27 on node -1
[ 0.836197] alloc kstat_irqs on node -1
[ 0.836206] pcieport 0000:00:1c.2: irq 27 for MSI/MSI-X
[ 0.836219] pcieport 0000:00:1c.2: setting latency timer to 64
[ 0.836388] alloc irq_desc for 28 on node -1
[ 0.836390] alloc kstat_irqs on node -1
[ 0.836400] pcieport 0000:00:1c.3: irq 28 for MSI/MSI-X
[ 0.836412] pcieport 0000:00:1c.3: setting latency timer to 64
[ 0.836529] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.836548] Firmware did not grant requested _OSC control
[ 0.836572] Firmware did not grant requested _OSC control
[ 0.836589] Firmware did not grant requested _OSC control
[ 0.836605] Firmware did not grant requested _OSC control
[ 0.836621] Firmware did not grant requested _OSC control
[ 0.836654] Firmware did not grant requested _OSC control
[ 0.836671] Firmware did not grant requested _OSC control
[ 0.836687] Firmware did not grant requested _OSC control
[ 0.836703] Firmware did not grant requested _OSC control
[ 0.836719] Firmware did not grant requested _OSC control
[ 0.836737] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.837854] ACPI: AC Adapter [AC] (on-line)
[ 0.837965] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:02/PNP0C0C:00/input/input0
[ 0.837970] ACPI: Power Button [PWRB]
[ 0.838019] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:02/PNP0C0D:00/input/input1
[ 0.838067] ACPI: Lid Switch [LID0]
[ 0.838120] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:02/PNP0C0E:00/input/input2
[ 0.838124] ACPI: Sleep Button [SLPB]
[ 0.838184] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 0.838187] ACPI: Power Button [PWRF]
[ 0.838959] ACPI: SSDT 7fe7ac90 0022C (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.839605] ACPI: SSDT 7fe79610 005D7 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.841980] Monitor-Mwait will be used to enter C-1 state
[ 0.842010] Monitor-Mwait will be used to enter C-2 state
[ 0.842036] Monitor-Mwait will be used to enter C-3 state
[ 0.842045] Marking TSC unstable due to TSC halts in idle
[ 0.842092] Switching to clocksource hpet
[ 0.842166] processor LNXCPU:00: registered as cooling_device0
[ 0.842549] ACPI: SSDT 7fe7af10 000C4 (v01 PmRef Cpu1Ist 00003000 INTL 20051117)
[ 0.843015] ACPI: SSDT 7fe7cd10 00083 (v01 PmRef Cpu1Cst 00003000 INTL 20051117)
[ 0.844009] processor LNXCPU:01: registered as cooling_device1
[ 0.874040] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.874049] ACPI: Thermal Zone [TZ01] (40 C)
[ 0.874224] isapnp: Scanning for PnP cards...
[ 0.875799] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.877399] brd: module loaded
[ 0.877933] loop: module loaded
[ 0.878025] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[ 0.878122] ata_piix 0000:00:1f.1: version 2.13
[ 0.878135] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.878178] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.878253] scsi0 : ata_piix
[ 0.878331] scsi1 : ata_piix
[ 0.878942] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x60e0 irq 14
[ 0.878946] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x60e8 irq 15
[ 0.879326] Fixed MDIO Bus: probed
[ 0.879363] PPP generic driver version 2.4.2
[ 0.879401] tun: Universal TUN/TAP device driver, 1.6
[ 0.879403] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.879491] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.879512] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.879525] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[ 0.879529] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[ 0.879562] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[ 0.879594] ehci_hcd 0000:00:1a.7: debug port 1
[ 0.883484] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[ 0.883499] ehci_hcd 0000:00:1a.7: irq 18, io mem 0x9b304c00
[ 0.900074] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[ 0.900168] usb usb1: configuration #1 chosen from 1 choice
[ 0.900200] hub 1-0:1.0: USB hub found
[ 0.900209] hub 1-0:1.0: 4 ports detected
[ 0.900273] alloc irq_desc for 23 on node -1
[ 0.900276] alloc kstat_irqs on node -1
[ 0.900281] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.900293] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.900296] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.900333] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[ 0.900361] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.904239] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 0.904253] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x9b304800
[ 0.920036] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.920115] usb usb2: configuration #1 chosen from 1 choice
[ 0.920144] hub 2-0:1.0: USB hub found
[ 0.920152] hub 2-0:1.0: 6 ports detected
[ 0.920219] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.920237] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.920258] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.920264] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[ 0.920268] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[ 0.920308] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[ 0.920348] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000060c0
[ 0.920444] usb usb3: configuration #1 chosen from 1 choice
[ 0.920473] hub 3-0:1.0: USB hub found
[ 0.920482] hub 3-0:1.0: 2 ports detected
[ 0.920535] alloc irq_desc for 21 on node -1
[ 0.920537] alloc kstat_irqs on node -1
[ 0.920542] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 0.920549] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[ 0.920553] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[ 0.920586] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[ 0.920624] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000060a0
[ 0.920725] usb usb4: configuration #1 chosen from 1 choice
[ 0.920756] hub 4-0:1.0: USB hub found
[ 0.920766] hub 4-0:1.0: 2 ports detected
[ 0.920819] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.920826] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.920830] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.920865] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
[ 0.920895] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00006080
[ 0.920991] usb usb5: configuration #1 chosen from 1 choice
[ 0.921022] hub 5-0:1.0: USB hub found
[ 0.921029] hub 5-0:1.0: 2 ports detected
[ 0.921082] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.921090] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.921094] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.921126] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
[ 0.921164] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00006060
[ 0.921263] usb usb6: configuration #1 chosen from 1 choice
[ 0.921296] hub 6-0:1.0: USB hub found
[ 0.921304] hub 6-0:1.0: 2 ports detected
[ 0.921356] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.921363] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.921367] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.921403] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
[ 0.921432] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00006040
[ 0.921532] usb usb7: configuration #1 chosen from 1 choice
[ 0.921560] hub 7-0:1.0: USB hub found
[ 0.921567] hub 7-0:1.0: 2 ports detected
[ 0.921669] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[ 0.961414] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.961434] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.961515] mice: PS/2 mouse device common for all mice
[ 0.961669] rtc_cmos 00:03: RTC can wake from S4
[ 0.961707] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.961741] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs
[ 0.961845] device-mapper: uevent: version 1.0.3
[ 0.961942] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 0.962009] device-mapper: multipath: version 1.1.0 loaded
[ 0.962012] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 0.962131] EISA: Probing bus 0 at eisa.0
[ 0.962138] Cannot allocate resource for EISA slot 1
[ 0.962140] Cannot allocate resource for EISA slot 2
[ 0.962143] Cannot allocate resource for EISA slot 3
[ 0.962145] Cannot allocate resource for EISA slot 4
[ 0.962147] Cannot allocate resource for EISA slot 5
[ 0.962149] Cannot allocate resource for EISA slot 6
[ 0.962160] EISA: Detected 0 cards.
[ 0.962314] cpuidle: using governor ladder
[ 0.962445] cpuidle: using governor menu
[ 0.962944] TCP cubic registered
[ 0.963115] NET: Registered protocol family 10
[ 0.963655] lo: Disabled Privacy Extensions
[ 0.964120] NET: Registered protocol family 17
[ 0.964529] Using IPI No-Shortcut mode
[ 0.964606] PM: Resume from disk failed.
[ 0.964620] registered taskstats version 1
[ 0.965408] Magic number: 6:561:689
[ 0.965490] rtc_cmos 00:03: setting system clock to 2010-08-11 15:41:58 UTC (1281541318)
[ 0.965493] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.965495] EDD information not available.
[ 0.991352] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 1.055793] ata1.00: ATAPI: Optiarc DVD RW AD-7560A, DX06, max UDMA/33
[ 1.072288] ata1.00: configured for UDMA/33
[ 1.228868] isapnp: No Plug & Play device found
[ 1.230007] scsi 0:0:0:0: CD-ROM Optiarc DVD RW AD-7560A DX06 PQ: 0 ANSI: 5
[ 1.235532] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.235535] Uniform CD-ROM driver Revision: 3.20
[ 1.235637] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.235685] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 1.235780] Freeing unused kernel memory: 660k freed
[ 1.236141] ACPI: Battery Slot [BAT0] (battery present)
[ 1.236201] Write protecting the kernel text: 4680k
[ 1.236264] Write protecting the kernel read-only data: 1840k
[ 1.254008] udev: starting version 151
[ 1.336703] ahci 0000:00:1f.2: version 3.0
[ 1.336726] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 1.336774] alloc irq_desc for 29 on node -1
[ 1.336776] alloc kstat_irqs on node -1
[ 1.336789] ahci 0000:00:1f.2: irq 29 for MSI/MSI-X
[ 1.336859] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x3 impl SATA mode
[ 1.336863] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc ems
[ 1.336870] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.337187] tg3.c:v3.102 (September 1, 2009)
[ 1.337248] tg3 0000:05:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 1.337263] tg3 0000:05:00.0: setting latency timer to 64
[ 1.354652] ACPI: EC: GPE storm detected, transactions will use polling mode
[ 1.409734] scsi2 : ahci
[ 1.430694] scsi3 : ahci
[ 1.434425] alloc irq_desc for 20 on node -1
[ 1.434428] alloc kstat_irqs on node -1
[ 1.434436] ohci1394 0000:07:00.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 1.434444] ohci1394 0000:07:00.0: setting latency timer to 64
[ 1.439167] eth0: Tigon3 [partno(BCM95787m) rev b002] (PCI Express) MAC address 00:1b:38:68:30:be
[ 1.439171] eth0: attached PHY is 5787 (10/100/1000Base-T Ethernet) (WireSpeed[1])
[ 1.439174] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 1.439176] eth0: dma_rwctrl[76180000] dma_mask[64-bit]
[ 1.439440] scsi4 : ahci
[ 1.439654] ata3: SATA max UDMA/133 abar m2048@0x9b304000 port 0x9b304100 irq 29
[ 1.439659] ata4: SATA max UDMA/133 abar m2048@0x9b304000 port 0x9b304180 irq 29
[ 1.439661] ata5: DUMMY
[ 1.490149] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[97000000-970007ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 1.500115] usb 2-4: new high speed USB device using ehci_hcd and address 2
[ 1.641172] usb 2-4: configuration #1 chosen from 1 choice
[ 1.752113] usb 2-5: new high speed USB device using ehci_hcd and address 3
[ 1.756076] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.756100] ata4: SATA link down (SStatus 0 SControl 300)
[ 1.756733] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
[ 1.807954] ata3.00: ATA-7: WDC WD1600BEVS-22RST0, 04.01G04, max UDMA/133
[ 1.807958] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.809040] ata3.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 1.809337] ata3.00: configured for UDMA/133
[ 1.824302] scsi 2:0:0:0: Direct-Access ATA WDC WD1600BEVS-2 04.0 PQ: 0 ANSI: 5
[ 1.824481] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 1.824506] sd 2:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 1.824577] sd 2:0:0:0: [sda] Write Protect is off
[ 1.824580] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.824610] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.824764] sda: sda1 sda2 < sda5 >
[ 1.861823] sd 2:0:0:0: [sda] Attached SCSI disk
[ 1.886664] usb 2-5: configuration #1 chosen from 1 choice
[ 1.894615] Initializing USB Mass Storage driver...
[ 1.894758] scsi5 : SCSI emulation for USB Mass Storage devices
[ 1.894865] usbcore: registered new interface driver usb-storage
[ 1.894869] USB Mass Storage support registered.
[ 1.894991] usb-storage: device found at 3
[ 1.894993] usb-storage: waiting for device to settle before scanning
[ 2.228231] EXT4-fs (sda1): mounted filesystem with ordered data mode
[ 2.764419] ieee1394: Host added: ID:BUS[0-00:1023] GUID[b6411da400023f7a]
[ 6.892516] usb-storage: device scan complete
[ 6.893102] scsi 5:0:0:0: Direct-Access USBModem Disk 2.31 PQ: 0 ANSI: 2
[ 6.893652] sd 5:0:0:0: Attached scsi generic sg2 type 0
[ 6.894316] sd 5:0:0:0: [sdb] 65536 512-byte logical blocks: (33.5 MB/32.0 MiB)
[ 6.894813] sd 5:0:0:0: [sdb] Write Protect is on
[ 6.894816] sd 5:0:0:0: [sdb] Mode Sense: 0f 0e 80 00
[ 6.894819] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 6.896823] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 6.896829] sdb:
[ 6.899472] sd 5:0:0:0: [sdb] Assuming drive cache: write through
[ 6.899475] sd 5:0:0:0: [sdb] Attached SCSI disk
[ 17.272643] udev: starting version 151
[ 17.288344] Adding 6034424k swap on /dev/sda5. Priority:-1 extents:1 across:6034424k
[ 17.329284] lirc_dev: IR Remote Control driver registered, major 61
[ 17.330007] lirc_dev: lirc_register_driver: sample_rate: 0
[ 17.330127] enecir: KB3926B detected
[ 17.330130] enecir: chip is 0x3909 - 0x24, 0xc0
[ 17.330132] enecir: driver has been succesfully loaded
[ 17.346100] lp: driver loaded but no devices found
[ 17.354606] usbcore: registered new interface driver usbserial
[ 17.354817] USB Serial support registered for generic
[ 17.355081] usbcore: registered new interface driver usbserial_generic
[ 17.355084] usbserial: USB Serial Driver core
[ 17.368228] irda_init()
[ 17.368240] NET: Registered protocol family 23
[ 17.371625] IrCOMM protocol (Dag Brattli)
[ 17.651689] acpi device:35: registered as cooling_device2
[ 17.651871] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:33/LNXVIDEO:00/input/input6
[ 17.651927] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 17.864023] Linux agpgart interface v0.103
[ 17.868957] vga16fb: initializing
[ 17.868963] vga16fb: mapped to 0xc00a0000
[ 17.869030] fb0: VGA16 VGA frame buffer device
[ 17.967382] nvidia: module license 'NVIDIA' taints kernel.
[ 17.967387] Disabling lock debugging due to kernel taint
[ 18.026223] type=1505 audit(1281534135.558:2): operation="profile_load" pid=715 name="/sbin/dhclient3"
[ 18.026989] type=1505 audit(1281534135.558:3): operation="profile_load" pid=715 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 18.027400] type=1505 audit(1281534135.558:4): operation="profile_load" pid=715 name="/usr/lib/connman/scripts/dhclient-script"
[ 18.059484] type=1505 audit(1281534135.590:5): operation="profile_load" pid=725 name="/usr/sbin/ntpd"
[ 18.111932] alloc irq_desc for 30 on node -1
[ 18.111936] alloc kstat_irqs on node -1
[ 18.112001] tg3 0000:05:00.0: irq 30 for MSI/MSI-X
[ 18.322675] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 18.354680] type=1505 audit(1281534135.886:6): operation="profile_load" pid=785 name="/usr/share/gdm/guest-session/Xsession"
[ 18.356550] type=1505 audit(1281534135.890:7): operation="profile_replace" pid=786 name="/sbin/dhclient3"
[ 18.357407] type=1505 audit(1281534135.890:8): operation="profile_replace" pid=786 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 18.357824] type=1505 audit(1281534135.890:9): operation="profile_replace" pid=786 name="/usr/lib/connman/scripts/dhclient-script"
[ 18.361341] type=1505 audit(1281534135.894:10): operation="profile_load" pid=787 name="/usr/bin/evince"
[ 18.371349] type=1505 audit(1281534135.902:11): operation="profile_load" pid=787 name="/usr/bin/evince-previewer"
[ 18.860266] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 18.860269] ricoh-mmc: Copyright(c) Philip Langdale
[ 18.860298] ricoh-mmc: Ricoh MMC controller found at 0000:07:00.2 [1180:0843] (rev 12)
[ 18.860319] ricoh-mmc: Controller is now disabled.
[ 18.863788] sdhci: Secure Digital Host Controller Interface driver
[ 18.863790] sdhci: Copyright(c) Pierre Ossman
[ 18.869513] sdhci-pci 0000:07:00.1: SDHCI controller found [1180:0822] (rev 22)
[ 18.869534] alloc irq_desc for 22 on node -1
[ 18.869537] alloc kstat_irqs on node -1
[ 18.869544] sdhci-pci 0000:07:00.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22
[ 18.872284] Registered led device: mmc0::
[ 18.873377] mmc0: SDHCI controller on PCI [0000:07:00.1] using PIO
[ 18.945412] Linux video capture interface: v2.00
[ 18.949339] acer-wmi: Acer Laptop ACPI-WMI Extras
[ 18.950151] uvcvideo: Found UVC 1.00 device Acer CrystalEye webcam (064e:a101)
[ 18.953485] input: Acer CrystalEye webcam as /devices/pci0000:00/0000:00:1d.7/usb2/2-4/2-4:1.0/input/input7
[ 18.953624] usbcore: registered new interface driver uvcvideo
[ 18.954216] USB Video Class driver (v0.1.0)
[ 18.980140] acer-wmi: Brightness must be controlled by generic video driver
[ 19.035595] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 19.035631] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 19.090346] nvidia 0000:01:00.0: power state changed by ACPI to D0
[ 19.090360] nvidia 0000:01:00.0: power state changed by ACPI to D0
[ 19.090375] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 19.090387] nvidia 0000:01:00.0: setting latency timer to 64
[ 19.090397] vgaarb: device changed decodes: PCI:0000:01:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 19.090606] NVRM: loading NVIDIA UNIX x86 Kernel Module 195.36.24 Thu Apr 22 09:18:20 PDT 2010
[ 19.174359] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input8
[ 19.245557] cfg80211: Calling CRDA to update world regulatory domain
[ 19.297198] Console: switching to colour frame buffer device 80x30
[ 19.308780] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26ks
[ 19.308785] iwl3945: Copyright(c) 2003-2009 Intel Corporation
[ 19.308863] iwl3945 0000:06:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19
[ 19.308878] iwl3945 0000:06:00.0: setting latency timer to 64
[ 19.325588] cfg80211: World regulatory domain updated:
[ 19.325592] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 19.325595] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.325598] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.325601] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.325604] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.325607] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.389146] iwl3945 0000:06:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
[ 19.389151] iwl3945 0000:06:00.0: Detected Intel Wireless WiFi Link 3945ABG
[ 19.389272] alloc irq_desc for 31 on node -1
[ 19.389274] alloc kstat_irqs on node -1
[ 19.389309] iwl3945 0000:06:00.0: irq 31 for MSI/MSI-X
[ 19.407802] phy0: Selected rate control algorithm 'iwl-3945-rs'
[ 19.425105] iwl3945 0000:06:00.0: firmware: requesting iwlwifi-3945-2.ucode
[ 19.470298] iwl3945 0000:06:00.0: loaded firmware version 15.32.2.9
[ 19.541522] Registered led device: iwl-phy0::radio
[ 19.544818] Registered led device: iwl-phy0::assoc
[ 19.545147] Registered led device: iwl-phy0::RX
[ 19.545420] Registered led device: iwl-phy0::TX
[ 19.557682] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 19.647343] input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input9
[ 19.684947] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input10
[ 20.945064] usb 2-5: USB disconnect, address 3
[ 21.188055] usb 2-5: new high speed USB device using ehci_hcd and address 4
[ 21.322815] usb 2-5: configuration #1 chosen from 1 choice
[ 21.334338] usbserial_generic 2-5:1.0: generic converter detected
[ 21.334416] usb 2-5: generic converter now attached to ttyUSB0
[ 21.334476] usbserial_generic 2-5:1.1: generic converter detected
[ 21.334529] usb 2-5: generic converter now attached to ttyUSB1
[ 21.341617] scsi6 : SCSI emulation for USB Mass Storage devices
[ 21.342968] usbserial_generic 2-5:1.3: generic converter detected
[ 21.343049] usb 2-5: generic converter now attached to ttyUSB2
[ 21.344892] usb-storage: device found at 4
[ 21.344894] usb-storage: waiting for device to settle before scanning
[ 23.008237] ppdev: user-space parallel port driver
[ 26.341180] usb-storage: device scan complete
[ 26.341856] scsi 6:0:0:0: Direct-Access USBModem Disk 2.31 PQ: 0 ANSI: 2
[ 26.344010] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 26.346242] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 53.612052] CE: hpet increasing min_delta_ns to 15000 nsec
[ 858.282334] wlan0: deauthenticating from 00:1d:6a:86:5e:f1 by local choice (reason=3)
[ 858.284536] wlan0: direct probe to AP 00:1d:6a:86:5e:f1 (try 1)
[ 858.287014] wlan0: direct probe responded
[ 858.287022] wlan0: authenticate with AP 00:1d:6a:86:5e:f1 (try 1)
[ 858.289460] wlan0: authenticated
[ 858.289496] wlan0: associate with AP 00:1d:6a:86:5e:f1 (try 1)
[ 858.292548] wlan0: RX AssocResp from 00:1d:6a:86:5e:f1 (capab=0x421 status=0 aid=1)
[ 858.292554] wlan0: associated
[ 858.294513] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 868.800073] wlan0: no IPv6 routers present
[25072.920063] CE: hpet increasing min_delta_ns to 22500 nsec
umberto@umbertoori-aceraspire5720:~$
Infine ho installato ircp-tray ma quando vado ad aprirlo mi dice:
Servizio irda non avviato!
È necessario modificare «/etc/default/irda-utils» e impostare la partenza all'avvio di irattach .
Altrimenti provare a digitare nel terminale:
"sudo irattach /dev/ttyS1 -s"
Leggere il manuale di irattach per maggiori informazioni.
Ircp Tray non sarà in grado di funzionare.
Ho fatto quanto indicato ma l'avviso ricompare, quindi immagino che sia un problema di riconoscimento o configurazione della porta.
Avete qualche suggerimento su come procedere?
Grazie