Pagina 2 di 2
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 20:50
da andyrock
Riavvia il computer e quando ti compare il menu di grub seleziona la voce da cui fai partire ubuntu (normalmente la prima) e premi 'e'. Spostati sulla riga relativa al kernel a aggiungi alla fine di questa noapic e primi CTRL+X
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 21:26
da d-io
ho solo ubuntu, quindi non mi mostra il grub all'avvio... sto cercando come "attivarlo" perchè non ricordo nemmeno quello
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 21:31
da andyrock
Tieni premuto il tasto shift (maiusc) all'avivo.
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 21:35
da d-io
appena trovato e scoperto sinceramente, ora eseguo. -> ->
ok ho FATTO, ho aggiungo noapic
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 21:42
da andyrock
Prova a vedere se ti funziona adesso.
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 21:47
da d-io
si la pen drive viene letta perfettamente. però non legge la cam, se aprò un programma per la cattura da cam (guvcview) mi dice: Unable to allocate Buffers, Please try restarting your system.
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 21:49
da andyrock
Ok, fai come prima però invece di inserire noapic inserisci pci=routeirq e prova a vedere se funziona.
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 21:57
da d-io
ora ripresenta il problema originale, ossia con la cam collegata (e funzionante) la pen drive non va. senza cam la pen drive va
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 21:58
da andyrock
Adesso prova con pci=noacpi
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 22:04
da d-io
la pen drive va bene sempre, la cam non viene letta
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 22:07
da andyrock
Questa è la penultima opzione che ti so consigliare: acpi=off
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 22:12
da d-io
niente, problema originale
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 22:13
da andyrock
Ecco l'ultima opzione che ti consiglio: irqpoll
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 22:16
da d-io
niente anche in questo modo mi ridà il problema originale
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 22:20
da andyrock
Riavvia e senza aggiungere nessuna opzione dai:
Posta l'output. Mi raccomando deve essere inserita sia la webcam che la memoria usb.
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 22:22
da d-io
eccolo
Codice: Seleziona tutto
arco@Maverik:~$ cat /proc/interrupts
CPU0 CPU1
0: 27 0 IO-APIC-edge timer
1: 0 2 IO-APIC-edge i8042
4: 1 1 IO-APIC-edge
7: 0 0 IO-APIC-edge parport0
8: 1 0 IO-APIC-edge rtc0
9: 0 0 IO-APIC-fasteoi acpi
12: 3 1 IO-APIC-edge i8042
14: 103 111 IO-APIC-edge ata_piix
15: 0 0 IO-APIC-edge ata_piix
16: 263 255 IO-APIC-fasteoi uhci_hcd:usb5, HDA Intel
18: 0 0 IO-APIC-fasteoi uhci_hcd:usb4
19: 0 0 IO-APIC-fasteoi uhci_hcd:usb3
23: 8711 2283 IO-APIC-fasteoi ata_piix, ehci_hcd:usb1, uhci_hcd:usb2, bttv0, Bt87x audio
26: 100 1009 PCI-MSI-edge i915
27: 99 898 PCI-MSI-edge eth0
NMI: 0 0 Non-maskable interrupts
LOC: 11798 5504 Local timer interrupts
SPU: 0 0 Spurious interrupts
PMI: 0 0 Performance monitoring interrupts
PND: 0 0 Performance pending work
RES: 1066 2759 Rescheduling interrupts
CAL: 53 85 Function call interrupts
TLB: 213 269 TLB shootdowns
TRM: 0 0 Thermal event interrupts
THR: 0 0 Threshold APIC interrupts
MCE: 0 0 Machine check exceptions
MCP: 1 1 Machine check polls
ERR: 1
MIS: 0
marco@Maverik:~$
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 22:31
da andyrock
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: domenica 3 ottobre 2010, 22:41
da d-io
eccolo qui
Codice: Seleziona tutto
marco@Maverik:~$ lsusb -t
/: Bus 05.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
/: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
|__ Port 1: Dev 2, If 0, Class=HID, Driver=usbhid, 1.5M
|__ Port 1: Dev 2, If 1, Class=HID, Driver=usbhid, 1.5M
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci_hcd/8p, 480M
|__ Port 2: Dev 6, If 0, Class='bInterfaceClass 0x0e not yet handled', Driver=uvcvideo, 480M
|__ Port 2: Dev 6, If 1, Class='bInterfaceClass 0x0e not yet handled', Driver=uvcvideo, 480M
|__ Port 6: Dev 7, If 0, Class=stor., Driver=usb-storage, 480M
marco@Maverik:~$
Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: lunedì 4 ottobre 2010, 19:17
da magozurlinux
Ciao,
eccoti l'output di
lspci -vvn con webcam e chiavetta di rete wireless entrambe collegate:
Codice: Seleziona tutto
jupiter@jupiter:~$ lspci -vvn
00:00.0 0600: 1106:3099
Subsystem: 1043:807f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=32M]
Capabilities: <access denied>
Kernel driver in use: agpgart-via
Kernel modules: via-agp
00:01.0 0604: 1106:b099
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: de000000-deefffff
Prefetchable memory behind bridge: def00000-dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp
00:05.0 0401: 13f6:0111 (rev 10)
Subsystem: 1043:80e2
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at b800 [size=256]
Capabilities: <access denied>
Kernel driver in use: C-Media PCI
Kernel modules: snd-cmipci
00:09.0 0c03: 1106:3038 (rev 50)
Subsystem: 1043:8080
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at b400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:09.1 0c03: 1106:3038 (rev 50)
Subsystem: 1043:8080
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 16
Region 4: I/O ports at b000 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:09.2 0c03: 1106:3104 (rev 51) (prog-if 20)
Subsystem: 1043:8080
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 17
Region 0: Memory at dd800000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:0c.0 0c03: 1106:3038 (rev 61)
Subsystem: 1106:3038
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at a800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:0c.1 0c03: 1106:3038 (rev 61)
Subsystem: 1106:3038
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 16
Region 4: I/O ports at a400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:0c.2 0c03: 1106:3104 (rev 63) (prog-if 20)
Subsystem: 1106:3104
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 17
Region 0: Memory at dd000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:11.0 0601: 1106:3147
Subsystem: 1043:808c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel modules: i2c-viapro, via-ircc
00:11.1 0101: 1106:0571 (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: 1043:808c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 0
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at a000 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_via
Kernel modules: pata_via
00:11.2 0c03: 1106:3038 (rev 23)
Subsystem: 1043:808c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 21
Region 4: I/O ports at 9800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:11.3 0c03: 1106:3038 (rev 23)
Subsystem: 1043:808c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 21
Region 4: I/O ports at 9400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
01:00.0 0300: 1002:475a (rev 3a)
Subsystem: 1002:0084
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at df000000 (32-bit, prefetchable) [size=16M]
Region 1: I/O ports at d800 [size=256]
Region 2: Memory at de000000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at defe0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel modules: atyfb
jupiter@jupiter:~$
Ieri entrambe non funzionavano, oggi la webcam e la chiavetta wi-fi funzionano perfettamente.
Codice: Seleziona tutto
lsusb
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 003: ID 148f:2573 Ralink Technology, Corp. RT2501USB Wireless Adapter
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 002: ID 058f:9254 Alcor Micro Corp. Hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 05a9:0518 OmniVision Technologies, Inc. OV518 Webcam
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
jupiter@jupiter:~$
Saluti.

Re: Ubuntu 10.04 problemi dispositivi di storage usb
Inviato: lunedì 4 ottobre 2010, 19:47
da d-io
eh... e quindi?