Pagina 3 di 3

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 16:22
da iHero96
1280x1024 è 5:4 ma il mio monitor la supporta anche a 75Hz solo se installo i driver ho questo problema.

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 16:26
da cristian_c
iHero96 ha scritto: 1280x1024 è 5:4 ma il mio monitor la supporta anche a 75Hz solo se installo i driver ho questo problema.
Infatti è un formato inedito per me  ;D
Però non ho capito il motivo per cui ti servono i driver proprietari  :)

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 16:32
da iHero96
Ho molti problemi grafici ( linee, distorsioni, punti bianchi) e la risoluzione l'ho forzata io altrimenti restava a 1024x768

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 16:34
da cristian_c
iHero96 ha scritto: Ho molti problemi grafici ( linee distorsioni) e la risoluzione l'ho forzata io altrimenti restava a 1024x768
Forse i problemi derivano dal fatto che hai forzato la risoluzione. Come l'hai forzata?  ;)
Installare i drive rproprietari forse non risolverà i problemi, ma li potrebbe aggravare  :-\

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 16:36
da iHero96
l'ho forzata configurando l'xorg.conf così:

Codice: Seleziona tutto

Section "Screen"
  Identifier "Unknow"
  Monitor    "VGA-0"
  SubSection "Display"
    Modes "1280x1024_75.00"
  EndSubSection
EndSection

Section "Monitor"
  Identifier "VGA-0"
  Modeline "1280x1024_75.00"  138.75  1280 1368 1504 1728  1024 1027 1034 1072 -hsync +vsync
EndSection

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 16:54
da cristian_c
iHero96 ha scritto: l'ho forzata configurando l'xorg.conf così:

Codice: Seleziona tutto

Section "Screen"
  Identifier "Unknow"
  Monitor    "VGA-0"
  SubSection "Display"
    Modes "1280x1024_75.00"
  EndSubSection
EndSection

Section "Monitor"
  Identifier "VGA-0"
  Modeline "1280x1024_75.00"  138.75  1280 1368 1504 1728  1024 1027 1034 1072 -hsync +vsync
EndSection
Ho trovato qualcosa: http://www.stanchina.net/~flavio/debian/fglrx-installer.html  ;D

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 16:59
da iHero96
non c'è la mia scheda in elenco.....

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 17:03
da cristian_c
iHero96 ha scritto: non c'è la mia scheda in elenco.....
Non hai capito il motivo per cui l'ho linkata  ;D
6. Bugs and Workarounds
Non-standard screen sizes

It appears that the ATI driver will refuse any screen size that your monitor doesn't list in its VESA DDC info; for example, I can't get my preferred resolution of 1280x960(*) with my Samsung CRT monitor. The symptoms are the following: if multiple resolutions are listed in XF86Config (such as "1280x960" "1152x864" "1024x768" "800x600"), the display will open at 1024x768 with a noticeable delay (a couple of seconds).
There are two workarounds:

  1. List only one resolution (1280x960 in my case): the display will open at that resolution with no delay, but you won't be able to switch resolutions with Ctrl,Alt,+ and Ctrl,Alt,-
  2. Use Option "NoDDC" in the "Device" section, as shown above: this is harmless as long as you got your monitor timings right.

* I'd kill with my bare hands whoever came up with 1280x1024, which has non-square pixels unless you give up some screen real estate. The aspect ratio of a traditional CRT is 4/3 and all standard resolutions (such as 640x480, 800x600 and 1024x768) have that aspect ratio; the aspect ratio of 1280x1024 is 5/4, so pixels are slightly wider than a square and things on your display will look compressed in the vertical direction. Now call me picky, but I do notice it and i don't like it.

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 17:06
da iHero96
Quindi dovrei provare a installare i driver e poi modificare questo file?? "XF86Config"

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 17:20
da cristian_c
iHero96 ha scritto: Quindi dovrei provare a installare i driver e poi modificare questo file?? "XF86Config"
Azzera il tuo xorg.conf (o meglio fai una copia di backup) e segui questo link: http://www.linuxquestions.org/questions/linux-desktop-74/cant-set-to-1280x1024-on-ubuntu-with-ati-mobility-radeon-x1600-and-external-monitor-579335/  ;)

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 17:25
da iHero96
Ok ci proverò ma perchè a volte non vuole spegnersi o riavviarsi??

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 17:41
da cristian_c
iHero96 ha scritto: Ok ci proverò ma perchè a volte non vuole spegnersi o riavviarsi??
È accaduto anche adesso? Sei riuscito a spegnerlo?  ;)

Re: HD3300+driver "Segnale fuori dai limiti di Ingresso"

Inviato: giovedì 29 settembre 2011, 17:42
da iHero96
sì è risuccesso, ma l'ho forzato dal pulsante.......... :(