Card express NEC (ora Renesas) USB 3.0

[Crow©]

ciao a tutti ho un problema, in pratica ho una card express NEC (ora Renesas) USB 3.0 inserendo la card non mi era stata rilevata poi riavviando tutto ok, ma mi è capitato che dopo qualche monta e smonta della pendrive non le monta più, ecco un output di dmesg
il comando lspci mi restituisce questo

Codice: Seleziona tutto

02:00.0 USB Controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)

dmesg mi restituisce questo che forse può essere inerente al mio caso

Codice: Seleziona tutto

  0.388296] hub 1-0:1.0: USB hub found
[    0.388303] hub 1-0:1.0: 8 ports detected
[    0.388408] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.388432] uhci_hcd: USB Universal Host Controller Interface driver
[    0.388496] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    0.388508] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    0.388513] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    0.388562] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    0.388597] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001800
[    0.388752] hub 2-0:1.0: USB hub found
[    0.388757] hub 2-0:1.0: 2 ports detected
[    0.388828] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.388837] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    0.388841] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    0.388884] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    0.388929] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001820
[    0.389074] hub 3-0:1.0: USB hub found
[    0.389079] hub 3-0:1.0: 2 ports detected
[    0.389149] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.389158] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    0.389162] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    0.389201] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    0.389244] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001840
[    0.389394] hub 4-0:1.0: USB hub found
[    0.389399] hub 4-0:1.0: 2 ports detected
[    0.389478] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[    0.389487] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    0.389491] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    0.389532] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    0.389572] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001860
[    0.389718] hub 5-0:1.0: USB hub found
[    0.389723] hub 5-0:1.0: 2 ports detected

volevo sapere moduli e driver da installare o da utilizzare ed eventuali configurazioni.

grazie a tutti anticipatamente