SMART extended self test - "test automatico non riuscito"

TheJoe · Messaggio da **TheJoe** » domenica 18 novembre 2018, 12:08

Buongiorno,
spero di aver azzeccato la sezione giusta del forum.

Ho avviato un extended self test SMART del disco su cui ho installato i dati degli utenti (il sistema operativo è su un secondo disco). Ieri sullo stato di salute leggevo "15 errori", oggi "test automatico non riuscito". Il test "extended" solitamente dovrebbe durare più di un'ora, invece si è risolto nel giro di pochi minuti e questo mi ha un po' preoccupato. Purtroppo non so leggere i dati SMART. Ho eseguito il test sia con l'utility gnome-disks, sia con gsmartcontrol e il risultato è lo stesso.

Posto di seguito l'output completo nella speranza che qualche utente skillato possa aiutarmi.

Codice: Seleziona tutto

Complete error log:

SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 15
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 15 [14] occurred at disk power-on lifetime: 15128 hours (630 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 70 45 d5 18 00 00  Error: WP at LBA = 0x7045d518 = 1883624728

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  61 00 00 00 08 00 00 0f 8b 58 40 40 00     00:02:05.329  WRITE FPDMA QUEUED
  60 00 00 00 08 00 00 4b 01 21 00 40 00     00:02:03.397  READ FPDMA QUEUED
  60 00 00 00 08 00 00 4b 01 20 f8 40 00     00:02:03.397  READ FPDMA QUEUED
  60 00 00 00 08 00 00 4b 01 22 28 40 00     00:02:03.397  READ FPDMA QUEUED
  60 00 00 00 08 00 00 4b 01 21 10 40 00     00:02:03.397  READ FPDMA QUEUED

Error 14 [13] occurred at disk power-on lifetime: 15128 hours (630 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 04 b0 e5 a0 00 00  Error: UNC at LBA = 0x04b0e5a0 = 78701984

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 20 00 00 67 93 73 78 40 00     00:01:48.416  READ FPDMA QUEUED
  60 00 00 00 08 00 00 04 b0 e5 a0 40 00     00:01:45.660  READ FPDMA QUEUED
  60 00 00 00 50 00 00 0f 25 98 a8 40 00     00:01:45.653  READ FPDMA QUEUED
  60 00 00 01 00 00 00 22 7c fc 40 40 00     00:01:45.643  READ FPDMA QUEUED
  60 00 00 00 88 00 00 25 2b 50 18 40 00     00:01:45.631  READ FPDMA QUEUED

Error 13 [12] occurred at disk power-on lifetime: 15127 hours (630 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 70 44 47 f8 00 00  Error: UNC at LBA = 0x704447f8 = 1883523064

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 70 84 de 38 40 00     00:01:32.446  READ FPDMA QUEUED
  60 00 00 00 08 00 00 70 84 dd e0 40 00     00:01:32.445  READ FPDMA QUEUED
  60 00 00 00 08 00 00 70 84 dd 88 40 00     00:01:32.150  READ FPDMA QUEUED
  60 00 00 00 18 00 00 70 84 97 c0 40 00     00:01:32.145  READ FPDMA QUEUED
  60 00 00 00 30 00 00 70 84 96 78 40 00     00:01:32.143  READ FPDMA QUEUED

Error 12 [11] occurred at disk power-on lifetime: 15127 hours (630 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 04 b0 8e c0 00 00  Error: UNC at LBA = 0x04b08ec0 = 78679744

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 01 18 00 00 04 b1 28 c0 40 00     00:01:22.728  READ FPDMA QUEUED
  60 00 00 00 f8 00 00 05 72 55 00 40 00     00:01:22.728  READ FPDMA QUEUED
  60 00 00 01 20 00 00 04 b0 8e 00 40 00     00:01:22.727  READ FPDMA QUEUED
  60 00 00 0d f8 00 00 04 96 e8 00 40 00     00:01:22.727  READ FPDMA QUEUED
  60 00 00 00 08 00 00 12 84 08 18 40 00     00:01:22.727  READ FPDMA QUEUED

Error 11 [10] occurred at disk power-on lifetime: 15127 hours (630 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 04 b0 e5 98 00 00  Error: UNC at LBA = 0x04b0e598 = 78701976

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 12 84 08 18 40 00     00:01:07.080  READ FPDMA QUEUED
  60 00 00 01 e0 00 00 06 47 ed 68 40 00     00:01:07.078  READ FPDMA QUEUED
  60 00 00 05 60 00 00 06 47 e8 00 40 00     00:01:07.074  READ FPDMA QUEUED
  60 00 00 01 00 00 00 06 44 66 00 40 00     00:01:07.071  READ FPDMA QUEUED
  60 00 00 00 90 00 00 05 ca 21 b8 40 00     00:01:07.070  READ FPDMA QUEUED

Error 10 [9] occurred at disk power-on lifetime: 15127 hours (630 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 04 96 d9 00 00 00  Error: UNC at LBA = 0x0496d900 = 76994816

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 f8 00 00 05 72 55 00 40 00     00:00:56.092  READ FPDMA QUEUED
  60 00 00 00 d8 00 00 05 72 54 00 40 00     00:00:56.081  READ FPDMA QUEUED
  60 00 00 01 c0 00 00 05 72 50 00 40 00     00:00:56.072  READ FPDMA QUEUED
  60 00 00 00 e8 00 00 05 72 47 00 40 00     00:00:56.062  READ FPDMA QUEUED
  60 00 00 01 58 00 00 05 72 1c 00 40 00     00:00:56.047  READ FPDMA QUEUED

Error 9 [8] occurred at disk power-on lifetime: 15127 hours (630 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 70 40 10 f8 00 00  Error: UNC at LBA = 0x704010f8 = 1883246840

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 6f 41 25 80 40 00     00:00:48.651  READ FPDMA QUEUED
  60 00 00 00 08 00 00 70 40 10 f8 40 00     00:00:48.635  READ FPDMA QUEUED
  60 00 00 00 08 00 00 70 40 11 00 40 00     00:00:48.635  READ FPDMA QUEUED
  60 00 00 00 08 00 00 70 40 10 a8 40 00     00:00:48.634  READ FPDMA QUEUED
  ef 00 10 00 02 00 00 00 00 00 00 a0 00     00:00:48.634  SET FEATURES [Enable SATA feature]

Error 8 [7] occurred at disk power-on lifetime: 15127 hours (630 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 70 40 10 f0 00 00  Error: UNC at LBA = 0x704010f0 = 1883246832

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 00 00 08 00 00 70 40 10 a8 40 00     00:00:44.652  READ FPDMA QUEUED
  60 00 00 00 08 00 00 70 40 11 00 40 00     00:00:44.652  READ FPDMA QUEUED
  60 00 00 00 08 00 00 70 40 10 f8 40 00     00:00:44.369  READ FPDMA QUEUED
  60 00 00 00 08 00 00 70 40 10 f0 40 00     00:00:44.368  READ FPDMA QUEUED
  60 00 00 00 08 00 00 70 40 10 e8 40 00     00:00:44.368  READ FPDMA QUEUED

Error 7 [6] occurred at disk power-on lifetime: 15051 hours (627 days + 3 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 00 01 29 28 00 00  Error: UNC at LBA = 0x00012928 = 76072

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 37 00 00 00 01 29 09 e0 00     00:00:25.490  READ DMA EXT
  25 00 00 00 09 00 00 00 01 29 00 e0 00     00:00:25.481  READ DMA EXT
  25 00 00 00 27 00 00 00 00 29 19 e0 00     00:00:25.477  READ DMA EXT
  25 00 00 00 19 00 00 00 00 29 00 e0 00     00:00:25.472  READ DMA EXT
  25 00 00 00 01 00 00 00 00 00 3f e0 00     00:00:25.463  READ DMA EXT

Error 6 [5] occurred at disk power-on lifetime: 14989 hours (624 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 08 8d 67 f0 00 00  Error: UNC at LBA = 0x088d67f0 = 143484912

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 22 00 00 08 8d 67 de e0 00     00:00:24.603  READ DMA EXT
  25 00 00 00 1e 00 00 08 8d 67 c0 e0 00     00:00:24.600  READ DMA EXT
  25 00 00 00 21 00 00 08 8d 67 9f e0 00     00:00:24.596  READ DMA EXT
  25 00 00 00 1f 00 00 08 8d 67 80 e0 00     00:00:24.593  READ DMA EXT
  25 00 00 00 20 00 00 08 8d 67 60 e0 00     00:00:24.590  READ DMA EXT

Error 5 [4] occurred at disk power-on lifetime: 14989 hours (624 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 08 8d 67 f0 00 00  Error: UNC at LBA = 0x088d67f0 = 143484912

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 22 00 00 08 8d 67 de e0 00     00:00:38.339  READ DMA EXT
  25 00 00 00 1e 00 00 08 8d 67 c0 e0 00     00:00:38.335  READ DMA EXT
  25 00 00 00 21 00 00 08 8d 67 9f e0 00     00:00:38.332  READ DMA EXT
  25 00 00 00 1f 00 00 08 8d 67 80 e0 00     00:00:38.329  READ DMA EXT
  25 00 00 00 20 00 00 08 8d 67 60 e0 00     00:00:38.326  READ DMA EXT

Error 4 [3] occurred at disk power-on lifetime: 14989 hours (624 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 08 8d 4d 98 00 00  Error: UNC at LBA = 0x088d4d98 = 143478168

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 37 00 00 08 8d 4d 89 e0 00     00:00:20.766  READ DMA EXT
  25 00 00 00 09 00 00 08 8d 4d 80 e0 00     00:00:20.763  READ DMA EXT
  25 00 00 00 36 00 00 08 8d 4d 4a e0 00     00:00:20.760  READ DMA EXT
  25 00 00 00 21 00 00 08 8d 48 1f e0 00     00:00:20.631  READ DMA EXT
  25 00 00 00 1f 00 00 08 8d 48 00 e0 00     00:00:20.620  READ DMA EXT

Error 3 [2] occurred at disk power-on lifetime: 14989 hours (624 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 08 8d 67 e8 00 00  Error: UNC at LBA = 0x088d67e8 = 143484904

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 22 00 00 08 8d 67 de e0 00     00:00:44.973  READ DMA EXT
  25 00 00 00 1e 00 00 08 8d 67 c0 e0 00     00:00:44.969  READ DMA EXT
  25 00 00 00 21 00 00 08 8d 67 9f e0 00     00:00:44.966  READ DMA EXT
  25 00 00 00 1f 00 00 08 8d 67 80 e0 00     00:00:44.963  READ DMA EXT
  25 00 00 00 20 00 00 08 8d 67 60 e0 00     00:00:44.959  READ DMA EXT

Error 2 [1] occurred at disk power-on lifetime: 14989 hours (624 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 08 8d 74 98 00 00  Error: UNC at LBA = 0x088d7498 = 143488152

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 05 00 00 08 8d 6e 00 e0 00     00:00:16.334  READ DMA EXT
  25 00 00 00 3a 00 00 08 8d 6d c6 e0 00     00:00:16.279  READ DMA EXT
  25 00 00 00 06 00 00 08 8d 6d c0 e0 00     00:00:16.276  READ DMA EXT
  25 00 00 00 39 00 00 08 8d 6d 87 e0 00     00:00:16.273  READ DMA EXT
  25 00 00 00 07 00 00 08 8d 6d 80 e0 00     00:00:16.270  READ DMA EXT

Error 1 [0] occurred at disk power-on lifetime: 14935 hours (622 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 00 08 8d 6d d0 00 00  Error: UNC at LBA = 0x088d6dd0 = 143486416

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 3a 00 00 08 8d 6d c6 e0 00     00:00:20.931  READ DMA EXT
  25 00 00 00 06 00 00 08 8d 6d c0 e0 00     00:00:20.928  READ DMA EXT
  25 00 00 00 39 00 00 08 8d 6d 87 e0 00     00:00:20.924  READ DMA EXT
  25 00 00 00 07 00 00 08 8d 6d 80 e0 00     00:00:20.921  READ DMA EXT
  25 00 00 00 38 00 00 08 8d 6d 48 e0 00     00:00:20.918  READ DMA EXT

La cosa che più mi preoccupa è la dicitura dell'errore 15 "media is write protected" nella schermata log di gsmartcontrol...

Grazie per l'aiuto.

Messaggio da **giulux** » domenica 18 novembre 2018, 12:11

Sposto in driver e periferiche.

wilecoyote

Salve, serve un test hardware sul disco.

Per controllare il disco fisso dai prima questo comando:

Codice: Seleziona tutto

lsblk

Dovrebbe essere /dev/sda il disco rigido, se il device è differente sostituiscilo conformemente nel prossimo comando per verificare il disco:

Codice: Seleziona tutto

sudo smartctl -a /dev/sda

Posta tutto l'output completo del prompt col comando medesimo, così di vedere com'è messo.

Ciao

TheJoe · Messaggio da **TheJoe** » domenica 18 novembre 2018, 16:43

Grazie dell'aiuto intanto...

Codice: Seleziona tutto

smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.15.0-39-lowlatency] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.14 (AF)
Device Model:     ST1000DM003-1CH162
Serial Number:    S1DBT4GD
LU WWN Device Id: 5 000c50 06187969c
Firmware Version: CC47
User Capacity:    1.000.204.886.016 bytes [1,00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    7200 rpm
Form Factor:      3.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is:  SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Sun Nov 18 16:41:45 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      ( 121)	The previous self-test completed having
					the read element of the test failed.
Total time to complete Offline 
data collection: 		(  575) seconds.
Offline data collection
capabilities: 			 (0x7b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 116) minutes.
Conveyance self-test routine
recommended polling time: 	 (   2) minutes.
SCT capabilities: 	       (0x3085)	SCT Status supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   108   099   006    Pre-fail  Always       -       16174664
  3 Spin_Up_Time            0x0003   098   097   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       779
  5 Reallocated_Sector_Ct   0x0033   100   100   010    Pre-fail  Always       -       376
  7 Seek_Error_Rate         0x000f   079   060   030    Pre-fail  Always       -       99794920
  9 Power_On_Hours          0x0032   072   072   000    Old_age   Always       -       24837
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       779
183 Runtime_Bad_Block       0x0032   001   001   000    Old_age   Always       -       340
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   085   085   000    Old_age   Always       -       15
188 Command_Timeout         0x0032   100   099   000    Old_age   Always       -       4 4 20
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   064   048   045    Old_age   Always       -       36 (Min/Max 22/39)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       155
193 Load_Cycle_Count        0x0032   100   100   000    Old_age   Always       -       811
194 Temperature_Celsius     0x0022   036   052   000    Old_age   Always       -       36 (0 16 0 0 0)
197 Current_Pending_Sector  0x0012   100   099   000    Old_age   Always       -       88
198 Offline_Uncorrectable   0x0010   100   099   000    Old_age   Offline      -       88
199 UDMA_CRC_Error_Count    0x003e   200   197   000    Old_age   Always       -       2591
240 Head_Flying_Hours       0x0000   100   253   000    Old_age   Offline      -       24857h+30m+59.386s
241 Total_LBAs_Written      0x0000   100   253   000    Old_age   Offline      -       20506839197
242 Total_LBAs_Read         0x0000   100   253   000    Old_age   Offline      -       11824553130

SMART Error Log Version: 1
ATA Error Count: 15 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 15 occurred at disk power-on lifetime: 15128 hours (630 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: WP at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  61 00 08 40 58 8b 4f 00      00:02:05.329  WRITE FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      00:02:03.397  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      00:02:03.397  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      00:02:03.397  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      00:02:03.397  READ FPDMA QUEUED

Error 14 occurred at disk power-on lifetime: 15128 hours (630 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 a0 e5 b0 04  Error: UNC at LBA = 0x04b0e5a0 = 78701984

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 20 ff ff ff 4f 00      00:01:48.416  READ FPDMA QUEUED
  60 00 08 a0 e5 b0 44 00      00:01:45.660  READ FPDMA QUEUED
  60 00 50 a8 98 25 4f 00      00:01:45.653  READ FPDMA QUEUED
  60 00 00 ff ff ff 4f 00      00:01:45.643  READ FPDMA QUEUED
  60 00 88 ff ff ff 4f 00      00:01:45.631  READ FPDMA QUEUED

Error 13 occurred at disk power-on lifetime: 15127 hours (630 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 08 ff ff ff 4f 00      00:01:32.446  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      00:01:32.445  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      00:01:32.150  READ FPDMA QUEUED
  60 00 18 ff ff ff 4f 00      00:01:32.145  READ FPDMA QUEUED
  60 00 30 ff ff ff 4f 00      00:01:32.143  READ FPDMA QUEUED

Error 12 occurred at disk power-on lifetime: 15127 hours (630 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 c0 8e b0 04  Error: UNC at LBA = 0x04b08ec0 = 78679744

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 18 c0 28 b1 44 00      00:01:22.728  READ FPDMA QUEUED
  60 00 f8 00 55 72 45 00      00:01:22.728  READ FPDMA QUEUED
  60 00 20 00 8e b0 44 00      00:01:22.727  READ FPDMA QUEUED
  60 00 f8 00 e8 96 44 00      00:01:22.727  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      00:01:22.727  READ FPDMA QUEUED

Error 11 occurred at disk power-on lifetime: 15127 hours (630 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 98 e5 b0 04  Error: UNC at LBA = 0x04b0e598 = 78701976

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 08 ff ff ff 4f 00      00:01:07.080  READ FPDMA QUEUED
  60 00 e0 68 ed 47 46 00      00:01:07.078  READ FPDMA QUEUED
  60 00 60 00 e8 47 46 00      00:01:07.074  READ FPDMA QUEUED
  60 00 00 00 66 44 46 00      00:01:07.071  READ FPDMA QUEUED
  60 00 90 b8 21 ca 45 00      00:01:07.070  READ FPDMA QUEUED

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed: read failure       90%     24832         1883620328
# 2  Short offline       Completed: read failure       50%     24832         1883620328
# 3  Extended offline    Completed: read failure       90%     24832         1883620328
# 4  Short offline       Completed: read failure       80%     24832         1883620328
# 5  Short offline       Completed: read failure       80%     24832         1883620328
# 6  Extended offline    Completed: read failure       90%     24808         1883620328
# 7  Short offline       Completed: read failure       90%     24808         1883620328
# 8  Extended offline    Completed: read failure       90%     22154         1883620328
# 9  Short offline       Completed: read failure       80%     22154         1883620328
#10  Short offline       Completed: read failure       40%     22154         1883620328
#11  Conveyance offline  Completed: read failure       90%     19074         1883623536
#12  Short offline       Completed: read failure       80%     19074         1883623536
#13  Short offline       Completed: read failure       10%     18638         1883620328
#14  Conveyance offline  Completed: read failure       90%     18638         1883620328
#15  Short offline       Completed: read failure       80%     18638         1883620328
#16  Extended offline    Completed: read failure       90%     15603         1883620328
#17  Short offline       Completed: read failure       70%     15603         1883623536
#18  Extended offline    Completed: read failure       90%     15057         143484912
#19  Short offline       Completed: read failure       90%     15057         143484912
#20  Extended offline    Completed without error       00%      9507         -
#21  Extended offline    Completed without error       00%      5952         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Questo è l'output... credevo fosse uguale a quello già postato.

wilecoyote

Salve, spiacente portar cattive notizie, fai un backup che sta andando il tuo HDD.

I parametri '1 Raw_Read_Error_Rate 16174664' e '7 Seek_Error_Rate 99794920' sono orripilanti ed il parametro '5 Reallocated_Sector_Ct 376' è brutto.

Inoltre leggo da questo parametro '9 Power_On_Hours 24837' che ha lavorato molte ore, ti fai un piacere a sostituirlo.

Il PASSED si riferisce ai circuiti elettronici.

Ciao

TheJoe · Messaggio da **TheJoe** » domenica 18 novembre 2018, 19:02

Ah, son proprio contento..

Grazie di avermi illuminato. Ciao!

wilecoyote

Salve,

TheJoe ha scritto:Ah, son proprio contento..

Grazie di avermi illuminato. Ciao!

Complimenti per prendere la cosa con ironia.

Altri avrebbero smoccolato l'impossibile…

Ciao

Forum Ubuntu-it

SMART extended self test - "test automatico non riuscito"

SMART extended self test - "test automatico non riuscito"

Re: SMART extended self test - "test automatico non riuscito

Re: SMART extended self test - "test automatico non riuscito

Re: SMART extended self test - "test automatico non riuscito

Re: SMART extended self test - "test automatico non riuscito

Re: SMART extended self test - "test automatico non riuscito

Re: SMART extended self test - "test automatico non riuscito

Chi c’è in linea

Accedi • Iscriviti