USB 2.0 wireless 802.IIN, problemi di istallazione

Riconoscimento, installazione e configurazione delle periferiche.
domes
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 566
Iscrizione: martedì 3 maggio 2011, 18:48

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da domes »

magozurlinux ha scritto:
lunedì 26 ottobre 2020, 12:24
Col browser metti il gateway della tua rete http://192.168.0.1 o 192.168.1.1; ti dovrebbe andare alla pagina di configurazione del modem/router, inserisci nome utente e password per entrare nella pagina di configurazione del modem/router.
Si, si , certo

Quello che voglio dire è che dopo aver cambiato il canale del router da automatico a 11 e aver riavviato sia il router che il pc al rientrare nella configurazione del router non mi fa piu vedere nè i dispositivi connessi via wifi al router ne le impostazioni wireless.

Comunque adesso la connessione salta meno anche se quando aggiorno una pagina pesante o comunque cerco di navigare cade di nuovo

Codice: Seleziona tutto

dmesg | grep usb
[   51.080653] Modules linked in: rfcomm bnep snd_hda_codec_hdmi snd_hda_codec_idt snd_hda_codec_generic binfmt_misc intel_rapl_msr mei_hdcp snd_hda_intel snd_intel_dspcfg intel_rapl_common snd_hda_codec x86_pkg_temp_thermal intel_powerclamp snd_hda_core coretemp dell_laptop ledtrig_audio kvm_intel snd_hwdep dell_smm_hwmon kvm snd_pcm iwldvm mac80211 snd_seq_midi crct10dif_pclmul snd_seq_midi_event ghash_clmulni_intel snd_rawmidi aesni_intel uvcvideo libarc4 crypto_simd cryptd videobuf2_vmalloc glue_helper videobuf2_memops videobuf2_v4l2 rapl btusb dell_wmi intel_cstate videobuf2_common dell_smbios snd_seq iwlwifi input_leds rtl8188fu(OE) btrtl i915 videodev joydev dcdbas btbcm btintel wmi_bmof mc sparse_keymap serio_raw dell_wmi_descriptor bluetooth snd_seq_device snd_timer drm_kms_helper cfg80211 ecdh_generic snd i2c_algo_bit ecc fb_sys_fops mei_me syscopyarea sysfillrect sysimgblt soundcore mei mac_hid sch_fq_codel parport_pc ppdev lp drm parport ip_tables x_tables autofs4 ums_realtek uas
[   51.080694]  usb_storage r8169 ahci crc32_pclmul psmouse i2c_i801 lpc_ich libahci realtek wmi video
[   89.797011] usb 3-1: USB disconnect, device number 2
[   89.797129] RTL871X: ###=> usb_read_port_complete => urb status(-108)
[   89.797131] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[   89.797132] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[   89.797133] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[   89.797134] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[   89.797136] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[   89.797137] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[   89.797138] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[   89.797176] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0xaa000000, vendorreq_times:1
[   89.797177] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0xaa000000, vendorreq_times:2
[   89.797179] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0xaa000000, vendorreq_times:3
[   89.797181] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0xaa000000, vendorreq_times:4
[   89.911856] RTL871X: usb_read_port_cancel
[   89.911858] RTL871X: usb_write_port_cancel 
[   90.183778] usb 3-1: new high-speed USB device number 3 using xhci_hcd
[   90.334220] usb 3-1: New USB device found, idVendor=0bda, idProduct=f179, bcdDevice= 0.00
[   90.334223] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   90.334225] usb 3-1: Product: 802.11n
[   90.334227] usb 3-1: Manufacturer: Realtek
[   90.334229] usb 3-1: SerialNumber: 1CBFCE7CCC75
               usb_endpoint_descriptor(0):
[   90.335163] RTL871X: RT_usb_endpoint_is_bulk_in = 1
               usb_endpoint_descriptor(1):
[   90.335167] RTL871X: RT_usb_endpoint_is_bulk_out = 2
               usb_endpoint_descriptor(2):
[   90.335171] RTL871X: RT_usb_endpoint_is_bulk_out = 3
[   90.737983] RTL871X: ### PS params=>  power_mgnt(2),usbss_enable(0) ###
[   90.753109] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[   90.753163] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[   91.015521] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[   91.015570] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[   91.660509] RTL871X: usb_AggSettingRxUpdate: RX Aggregation USB mode, size=20KB, timeout=1024us
[   94.104332] RTL871X: usb_read_port_cancel
[   94.104374] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   94.104410] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   94.104454] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   94.104496] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   94.104538] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   94.104580] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   94.104660] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   94.104701] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[   94.104709] RTL871X: usb_write_port_cancel 
[   94.183483] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[   94.183537] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[   94.815878] RTL871X: usb_AggSettingRxUpdate: RX Aggregation USB mode, size=20KB, timeout=1024us
[  100.141300] usb 3-1: USB disconnect, device number 3
[  100.141459] RTL871X: ###=> usb_read_port_complete => urb status(-71)
[  100.141536] RTL871X: ###=> usb_read_port_complete => urb status(-71)
[  100.141599] RTL871X: usb_write_port, status=-19
[  100.141624] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  100.141717] RTL871X: usb_write_port_complete(): TX Warning! bDriverStopped(True) OR bSurpriseRemoved(False) pxmitbuf->buf_tag(0)
[  100.141724] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  100.141725] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  100.141727] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  100.141727] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  100.141728] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  100.141793] RTL871X: usb_write_port_complete(): TX Warning! bDriverStopped(True) OR bSurpriseRemoved(False) pxmitbuf->buf_tag(0)
[  100.141873] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0xaa000000, vendorreq_times:1
[  100.141875] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0xaa000000, vendorreq_times:2
[  100.141876] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0xaa000000, vendorreq_times:3
[  100.254229] RTL871X: usb_read_port_cancel
[  100.254232] RTL871X: usb_write_port_cancel 
[  100.529933] usb 3-1: new high-speed USB device number 4 using xhci_hcd
[  100.688639] usb 3-1: New USB device found, idVendor=0bda, idProduct=f179, bcdDevice= 0.00
[  100.688648] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  100.688652] usb 3-1: Product: 802.11n
[  100.688654] usb 3-1: Manufacturer: Realtek
[  100.688659] usb 3-1: SerialNumber: 1CBFCE7CCC75
               usb_endpoint_descriptor(0):
[  100.690726] RTL871X: RT_usb_endpoint_is_bulk_in = 1
               usb_endpoint_descriptor(1):
[  100.690735] RTL871X: RT_usb_endpoint_is_bulk_out = 2
               usb_endpoint_descriptor(2):
[  100.690744] RTL871X: RT_usb_endpoint_is_bulk_out = 3
[  101.103472] RTL871X: ### PS params=>  power_mgnt(2),usbss_enable(0) ###
[  101.118484] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  101.118595] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  101.380336] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  101.380373] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  102.022868] RTL871X: usb_AggSettingRxUpdate: RX Aggregation USB mode, size=20KB, timeout=1024us
[  104.458574] RTL871X: usb_read_port_cancel
[  104.458632] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  104.458702] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  104.459383] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  104.459451] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  104.459494] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  104.459534] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  104.459572] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  104.459617] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  104.459630] RTL871X: usb_write_port_cancel 
[  104.535259] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  104.535356] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  105.174687] RTL871X: usb_AggSettingRxUpdate: RX Aggregation USB mode, size=20KB, timeout=1024us
[  119.137339] usb 3-1: USB disconnect, device number 4
[  119.137571] RTL871X: ###=> usb_read_port_complete => urb status(-108)
[  119.137583] RTL871X: usb_write_port_complete(): TX Warning! bDriverStopped(True) OR bSurpriseRemoved(False) pxmitbuf->buf_tag(0)
[  119.137593] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  119.137596] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  119.137599] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  119.137601] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  119.137604] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  119.137607] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  119.137609] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  119.137696] RTL871X: usb_write_port_complete(): TX Warning! bDriverStopped(True) OR bSurpriseRemoved(False) pxmitbuf->buf_tag(0)
[  119.137703] RTL871X: usb_write_port_complete(): TX Warning! bDriverStopped(True) OR bSurpriseRemoved(False) pxmitbuf->buf_tag(0)
[  119.138525] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0xaa000000, vendorreq_times:1
[  119.138528] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0xaa000000, vendorreq_times:2
[  119.138531] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0xaa000000, vendorreq_times:3
[  119.138532] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0xaa000000, vendorreq_times:4
[  119.208721] RTL871X: usb_read_port_cancel
[  119.208724] RTL871X: usb_write_port_cancel 
[  119.480737] usb 3-1: new high-speed USB device number 5 using xhci_hcd
[  119.631316] usb 3-1: New USB device found, idVendor=0bda, idProduct=f179, bcdDevice= 0.00
[  119.631323] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  119.631326] usb 3-1: Product: 802.11n
[  119.631329] usb 3-1: Manufacturer: Realtek
[  119.631332] usb 3-1: SerialNumber: 1CBFCE7CCC75
               usb_endpoint_descriptor(0):
[  119.632242] RTL871X: RT_usb_endpoint_is_bulk_in = 1
               usb_endpoint_descriptor(1):
[  119.632251] RTL871X: RT_usb_endpoint_is_bulk_out = 2
               usb_endpoint_descriptor(2):
[  119.632259] RTL871X: RT_usb_endpoint_is_bulk_out = 3
[  120.050486] RTL871X: ### PS params=>  power_mgnt(2),usbss_enable(0) ###
[  120.066610] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  120.066646] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  120.307624] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  120.307740] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  120.953764] RTL871X: usb_AggSettingRxUpdate: RX Aggregation USB mode, size=20KB, timeout=1024us
[  123.420712] RTL871X: usb_read_port_cancel
[  123.420768] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  123.421094] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  123.421141] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  123.421183] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  123.421222] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  123.421263] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  123.421304] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  123.421345] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  123.421357] RTL871X: usb_write_port_cancel 
[  123.494607] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  123.494700] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  124.130057] RTL871X: usb_AggSettingRxUpdate: RX Aggregation USB mode, size=20KB, timeout=1024us
[  157.055569] RTL871X: ###=> usb_read_port_complete => urb status(-71)
[  157.055640] RTL871X: ###=> usb_read_port_complete => urb status(-71)
[  157.055728] RTL871X: ###=> usb_read_port_complete => urb status(-71)
[  157.055850] RTL871X: ###=> usb_read_port_complete => urb status(-71)
[  157.055940] RTL871X: ###=> usb_read_port_complete => urb status(-71)
[  157.055974] usb 3-1: USB disconnect, device number 5
[  157.056015] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(True)
[  157.056098] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(True)
[  157.056101] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(True)
[  157.056102] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(True)
[  157.056103] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(True)
[  157.056104] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(True)
[  157.056106] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(True)
[  157.148587] RTL871X: usb_read_port_cancel
[  157.148590] RTL871X: usb_write_port_cancel 
[  157.433323] usb 3-1: new high-speed USB device number 6 using xhci_hcd
[  157.583884] usb 3-1: New USB device found, idVendor=0bda, idProduct=f179, bcdDevice= 0.00
[  157.583889] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
domes
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 566
Iscrizione: martedì 3 maggio 2011, 18:48

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da domes »

Non, riesco a modificare il router e non navigo praticamente.

Ci sarà una soluzione hardware, che sò un'altro wifiusb che sia piu facile da settare e che funzioni con ubuntu?
Avatar utente
magozurlinux
Accecante Asceta
Accecante Asceta
Messaggi: 21896
Iscrizione: mercoledì 17 marzo 2010, 17:44
Desktop: Xubuntu
Distribuzione: Ubuntu 20.04 LTS x86_64
Località: Pisa

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da magozurlinux »

domes ha scritto:
giovedì 29 ottobre 2020, 10:35
Non, riesco a modificare il router e non navigo praticamente.

Ci sarà una soluzione hardware, che sò un'altro wifiusb che sia piu facile da settare e che funzioni con ubuntu?
Dietro il router dovrebbe esserci un forellino con la scritta Reset; infila dentro la punta di un fermaglio aperto, aspetta 15'' così resetti il router; dovresti riuscire ad accedere nuovamente al router da browser.
Xubuntu 20.04 LTS amd64 :ciao:
domes
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 566
Iscrizione: martedì 3 maggio 2011, 18:48

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da domes »

Vediamo se riesco a spiegarmi.

Prima di comperare questa wifiusb avevo (ed ho) problemi con la wifi interna che non si connette alla rete finchè non si "riscalda".....voglio dire che dopo un pò che è accesa la laptop inizia a vedere le reti disponibili e si connette alla rete domestica: questo però dopo aver tenuto disabilitata la rete wifi in "modalità aereo" e provato e riprovato ad abilitarla con continui riavvii del sistema finchè si connette.

Al tentare di usare la wifiusb oggetto di questa discussione ho notato che quando la wifi interna si connette tutto funziona ma ci sono 2 connessioni alla stessa rete e valori un pò strani del tutto.

Sarà che il problema risiede proprio nella wifi interna?? c'è un modo di disabilitarla direttamente o definitivamente??
Schermata da 2020-10-29 11-50-14.png

Codice: Seleziona tutto

danieledell@danieledell-Inspiron-N5110:~$ sudo lshw -C network
[sudo] password di danieledell: 
  *-network                 
       description: Ethernet interface
       product: RTL810xE PCI Express Fast Ethernet controller
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 0
       bus info: pci@0000:05:00.0
       logical name: enp5s0
       version: 05
       serial: 24:b6:fd:1a:fa:53
       capacity: 100Mbit/s
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=r8169 firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII
       resources: irq:17 ioport:e000(size=256) memory:f1104000-f1104fff memory:f1100000-f1103fff
  *-network DISABLED
       description: Wireless interface
       product: Centrino Wireless-N 1030 [Rainbow Peak]
       vendor: Intel Corporation
       physical id: 0
       bus info: pci@0000:09:00.0
       logical name: wlp9s0
       version: 34
       serial: 4c:80:93:4d:4d:56
       width: 64 bits
       clock: 33MHz
       capabilities: pm msi pciexpress cap_list ethernet physical wireless
       configuration: broadcast=yes driver=iwlwifi driverversion=5.4.0-52-generic firmware=18.168.6.1 latency=0 link=no multicast=yes wireless=IEEE 802.11
       resources: irq:37 memory:f7e00000-f7e01fff
  *-network
       description: Wireless interface
       physical id: 2
       bus info: usb@3:1
       logical name: wlx1cbfce7ccc75
       serial: 1c:bf:ce:7c:cc:75
       capabilities: ethernet physical wireless
       configuration: broadcast=yes driver=rtl8188fu ip=192.168.1.115 multicast=yes wireless=IEEE 802.11bgn
danieledell@danieledell-Inspiron-N5110:~$ iwconfig
enp5s0    no wireless extensions.

wlp9s0    IEEE 802.11  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=15 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Power Management:on
          
wlx1cbfce7ccc75  IEEE 802.11bgn  ESSID:"TIM-29990241"  Nickname:"<WIFI@REALTEK>"
          Mode:Managed  Frequency:2.412 GHz  Access Point: A4:91:B1:C9:9D:61   
          Bit Rate:72.2 Mb/s   Sensitivity:0/0  
          Retry:off   RTS thr:off   Fragment thr:off
          Power Management:off
          Link Quality=95/100  Signal level=-48 dBm  Noise level=0 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

lo        no wireless extensions.

danieledell@danieledell-Inspiron-N5110:~$ dmesg | grep usb
[  166.161843] usb 3-1: new high-speed USB device number 2 using xhci_hcd
[  166.312267] usb 3-1: New USB device found, idVendor=0bda, idProduct=f179, bcdDevice= 0.00
[  166.312275] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  166.312279] usb 3-1: Product: 802.11n
[  166.312283] usb 3-1: Manufacturer: Realtek
[  166.312286] usb 3-1: SerialNumber: 1CBFCE7CCC75
               usb_endpoint_descriptor(0):
[  166.339107] RTL871X: RT_usb_endpoint_is_bulk_in = 1
               usb_endpoint_descriptor(1):
[  166.339111] RTL871X: RT_usb_endpoint_is_bulk_out = 2
               usb_endpoint_descriptor(2):
[  166.339115] RTL871X: RT_usb_endpoint_is_bulk_out = 3
[  166.738167] RTL871X: ### PS params=>  power_mgnt(2),usbss_enable(0) ###
[  166.752741] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  166.753847] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  166.938083] usbcore: registered new interface driver rtl8188fu
[  167.042221] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  167.042265] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  167.678857] RTL871X: usb_AggSettingRxUpdate: RX Aggregation USB mode, size=20KB, timeout=1024us
[  170.093598] RTL871X: usb_read_port_cancel
[  170.093640] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  170.093690] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  170.093742] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  170.093786] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  170.093825] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  170.093974] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  170.094019] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  170.094061] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  170.094069] RTL871X: usb_write_port_cancel 
[  170.164135] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  170.164261] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  170.802888] RTL871X: usb_AggSettingRxUpdate: RX Aggregation USB mode, size=20KB, timeout=1024us
[  381.232382] usb 3-1: USB disconnect, device number 2
[  381.232517] RTL871X: ###=> usb_read_port_complete => urb status(-108)
[  381.232519] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  381.232521] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  381.232522] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  381.232524] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  381.232525] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  381.232527] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  381.232528] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  381.232571] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0x48000000, vendorreq_times:1
[  381.232574] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0x48000000, vendorreq_times:2
[  381.232586] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0x48000000, vendorreq_times:3
[  381.232588] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0x48000000, vendorreq_times:4
[  381.331093] RTL871X: usb_read_port_cancel
[  381.331101] RTL871X: usb_write_port_cancel 
[  381.602770] usb 3-1: new high-speed USB device number 3 using xhci_hcd
[  381.753364] usb 3-1: New USB device found, idVendor=0bda, idProduct=f179, bcdDevice= 0.00
[  381.753372] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  381.753376] usb 3-1: Product: 802.11n
[  381.753390] usb 3-1: Manufacturer: Realtek
[  381.753394] usb 3-1: SerialNumber: 1CBFCE7CCC75
               usb_endpoint_descriptor(0):
[  381.754462] RTL871X: RT_usb_endpoint_is_bulk_in = 1
               usb_endpoint_descriptor(1):
[  381.754478] RTL871X: RT_usb_endpoint_is_bulk_out = 2
               usb_endpoint_descriptor(2):
[  381.754484] RTL871X: RT_usb_endpoint_is_bulk_out = 3
[  382.183244] RTL871X: ### PS params=>  power_mgnt(2),usbss_enable(0) ###
[  382.202173] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  382.202227] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  382.461966] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  382.462003] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  383.117272] RTL871X: usb_AggSettingRxUpdate: RX Aggregation USB mode, size=20KB, timeout=1024us
[  385.547054] RTL871X: usb_read_port_cancel
[  385.547105] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  385.547154] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  385.547262] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  385.547315] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  385.547356] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  385.547396] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  385.547439] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  385.548168] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  385.548184] RTL871X: usb_write_port_cancel 
[  385.621218] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  385.621311] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  386.263852] RTL871X: usb_AggSettingRxUpdate: RX Aggregation USB mode, size=20KB, timeout=1024us
[  389.539149] usb 3-1: USB disconnect, device number 3
[  389.539329] RTL871X: ###=> usb_read_port_complete => urb status(-108)
[  389.539335] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  389.539337] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  389.539338] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  389.539340] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  389.539341] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  389.539342] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  389.539344] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(True) OR bSurpriseRemoved(False)
[  389.539433] RTL871X: usb_write_port_complete(): TX Warning! bDriverStopped(True) OR bSurpriseRemoved(False) pxmitbuf->buf_tag(0)
[  389.539437] RTL871X: usb_write_port_complete(): TX Warning! bDriverStopped(True) OR bSurpriseRemoved(False) pxmitbuf->buf_tag(0)
[  389.539438] RTL871X: usb_write_port_complete(): TX Warning! bDriverStopped(True) OR bSurpriseRemoved(False) pxmitbuf->buf_tag(0)
[  389.539439] RTL871X: usb_write_port_complete(): TX Warning! bDriverStopped(True) OR bSurpriseRemoved(False) pxmitbuf->buf_tag(0)
[  389.539490] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0x48000000, vendorreq_times:1
[  389.539492] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0x48000000, vendorreq_times:2
[  389.539494] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0x48000000, vendorreq_times:3
[  389.539496] RTL871X: reg 0x6a4, usb write 2 fail, status:-19 value=0x48000000, vendorreq_times:4
[  389.618852] RTL871X: usb_read_port_cancel
[  389.618860] RTL871X: usb_write_port_cancel 
[  389.898572] usb 3-1: new high-speed USB device number 4 using xhci_hcd
[  390.053594] usb 3-1: New USB device found, idVendor=0bda, idProduct=f179, bcdDevice= 0.00
[  390.053598] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  390.053600] usb 3-1: Product: 802.11n
[  390.053602] usb 3-1: Manufacturer: Realtek
[  390.053603] usb 3-1: SerialNumber: 1CBFCE7CCC75
               usb_endpoint_descriptor(0):
[  390.055685] RTL871X: RT_usb_endpoint_is_bulk_in = 1
               usb_endpoint_descriptor(1):
[  390.055689] RTL871X: RT_usb_endpoint_is_bulk_out = 2
               usb_endpoint_descriptor(2):
[  390.055693] RTL871X: RT_usb_endpoint_is_bulk_out = 3
[  390.462244] RTL871X: ### PS params=>  power_mgnt(2),usbss_enable(0) ###
[  390.476861] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  390.476933] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  390.724732] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin
[  390.724768] usb 3-1: request firmware rtlwifi/rtl8188fufw.bin loaded
[  391.367646] RTL871X: usb_AggSettingRxUpdate: RX Aggregation USB mode, size=20KB, timeout=1024us
[  393.830937] RTL871X: usb_read_port_cancel
[  393.831010] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  393.831063] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  393.831105] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  393.831175] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  393.831244] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  393.831304] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  393.831367] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  393.831432] RTL871X: usb_read_port_complete() RX Warning! bDriverStopped(False) OR bSurpriseRemoved(False)
[  393.831441] RTL871X: usb_write_port_cancel 

Codice: Seleziona tutto

nmcli device wifi list
IN-USE  BSSID              SSID              MODE   CHAN  RATE        SIGNAL  B>
*       A4:91:B1:C9:9D:61  TIM-29990241      Infra  1     130 Mbit/s  75      ▂>
        E8:DF:70:D5:1C:D0  NetoIP.com-Mauro  Infra  1     195 Mbit/s  42      ▂>

IN-USE  BSSID              SSID          MODE   CHAN  RATE        SIGNAL  BARS >
*       A4:91:B1:C9:9D:61  TIM-29990241  Infra  1     130 Mbit/s  81      ▂▄▆█ >
lines 1-6/6 (END)

Avatar utente
magozurlinux
Accecante Asceta
Accecante Asceta
Messaggi: 21896
Iscrizione: mercoledì 17 marzo 2010, 17:44
Desktop: Xubuntu
Distribuzione: Ubuntu 20.04 LTS x86_64
Località: Pisa

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da magozurlinux »

In un mio precedente messaggio ti avevo detto che ci sono due dispositivi wireless nello stesso pc che si collegano alla tua rete; vanno in conflitto.

Da terminale postami questo comando:

Codice: Seleziona tutto

lspci -nnk | grep -A6 -i net
Xubuntu 20.04 LTS amd64 :ciao:
domes
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 566
Iscrizione: martedì 3 maggio 2011, 18:48

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da domes »

magozurlinux ha scritto:
giovedì 29 ottobre 2020, 17:48
In un mio precedente messaggio ti avevo detto che ci sono due dispositivi wireless nello stesso pc che si collegano alla tua rete; vanno in conflitto.
Si, ma non sò cosa sia......io ho solo cambiato il canale del mio laptop da automatico a 11 e quella NetoIP.com-Mauro ha cambiato allo stesso canale
Da terminale postami questo comando:

Codice: Seleziona tutto

lspci -nnk | grep -A6 -i net

Codice: Seleziona tutto

lspci -nnk | grep -A6 -i net
05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL810xE PCI Express Fast Ethernet controller [10ec:8136] (rev 05)
	Subsystem: Dell RTL810xE PCI Express Fast Ethernet controller [1028:04b0]
	Kernel driver in use: r8169
	Kernel modules: r8169
09:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1030 [Rainbow Peak] [8086:008a] (rev 34)
	Kernel driver in use: iwlwifi
	Kernel modules: iwlwifi
0b:00.0 USB controller [0c03]: Texas Instruments TUSB73x0 SuperSpeed USB 3.0 xHCI Host Controller [104c:8241] (rev 02)
	Subsystem: Dell TUSB73x0 SuperSpeed USB 3.0 xHCI Host Controller [1028:04b0]
	Kernel driver in use: xhci_hcd

Avatar utente
magozurlinux
Accecante Asceta
Accecante Asceta
Messaggi: 21896
Iscrizione: mercoledì 17 marzo 2010, 17:44
Desktop: Xubuntu
Distribuzione: Ubuntu 20.04 LTS x86_64
Località: Pisa

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da magozurlinux »

La scheda di rete wireless integrata è questa:
09:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1030 [Rainbow Peak] [8086:008a] (rev 34)
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
Da terminale dai questo comando:

Codice: Seleziona tutto

echo blacklist iwlwifi | sudo tee -a /etc/modprobe.d/blacklist.conf
riavvia il pc.

Vedi ora come va la connessione.
Xubuntu 20.04 LTS amd64 :ciao:
domes
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 566
Iscrizione: martedì 3 maggio 2011, 18:48

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da domes »

magozurlinux ha scritto:
venerdì 30 ottobre 2020, 9:37
La scheda di rete wireless integrata è questa:
09:00.0 Network controller [0280]: Intel Corporation Centrino Wireless-N 1030 [Rainbow Peak] [8086:008a] (rev 34)
Kernel driver in use: iwlwifi
Kernel modules: iwlwifi
Da terminale dai questo comando:

Codice: Seleziona tutto

echo blacklist iwlwifi | sudo tee -a /etc/modprobe.d/blacklist.conf
riavvia il pc.

Vedi ora come va la connessione.
Lo stesso, anzi peggio, salta dopo 2-3 secondi.
Poi in altri momenti "dura" di piu, non riesco a capire....sarà difettosa la pennetta a questo punto?
domes
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 566
Iscrizione: martedì 3 maggio 2011, 18:48

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da domes »

in alto
Avatar utente
magozurlinux
Accecante Asceta
Accecante Asceta
Messaggi: 21896
Iscrizione: mercoledì 17 marzo 2010, 17:44
Desktop: Xubuntu
Distribuzione: Ubuntu 20.04 LTS x86_64
Località: Pisa

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da magozurlinux »

domes ha scritto:
lunedì 2 novembre 2020, 11:34
in alto
Per rimettere com'era prima da terminale dai questi comandi:

Codice: Seleziona tutto

sudo -H gedit /etc/modprobe.d/blacklist.conf
cancella l'ultima riga

Codice: Seleziona tutto

blacklist iwlwifi
salva ed esci dall'editor di testo.

Riavvia il pc.

A me oggi la chiavetta come la tua col driver rtl8188fu non funziona più, rileva solo una rete che non è la mia.

Ho provato a rimuovere il driver e reinstallarlo, niente, non va più come prima, anche con Windows rileva solo una rete, non la mia. Bo!
Xubuntu 20.04 LTS amd64 :ciao:
domes
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 566
Iscrizione: martedì 3 maggio 2011, 18:48

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da domes »

magozurlinux ha scritto:
lunedì 2 novembre 2020, 18:32
domes ha scritto:
lunedì 2 novembre 2020, 11:34
in alto
Per rimettere com'era prima da terminale dai questi comandi:

Codice: Seleziona tutto

sudo -H gedit /etc/modprobe.d/blacklist.conf
cancella l'ultima riga

Codice: Seleziona tutto

blacklist iwlwifi
salva ed esci dall'editor di testo.

Riavvia il pc.

A me oggi la chiavetta come la tua col driver rtl8188fu non funziona più, rileva solo una rete che non è la mia.

Ho provato a rimuovere il driver e reinstallarlo, niente, non va più come prima, anche con Windows rileva solo una rete, non la mia. Bo!
Quindi non c'è modo di farla funzionare?

Esiste una wifiusb da comperare che sia compatibile con ubuntu 20.04?
Avatar utente
magozurlinux
Accecante Asceta
Accecante Asceta
Messaggi: 21896
Iscrizione: mercoledì 17 marzo 2010, 17:44
Desktop: Xubuntu
Distribuzione: Ubuntu 20.04 LTS x86_64
Località: Pisa

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da magozurlinux »

Prova a dare questo comando:

Codice: Seleziona tutto

echo REGDOMAIN=IT | sudo tee -a /etc/default/crda
riavvia il pc.
Xubuntu 20.04 LTS amd64 :ciao:
domes
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 566
Iscrizione: martedì 3 maggio 2011, 18:48

Re: USB 2.0 wireless 802.IIN, problemi di istallazione

Messaggio da domes »

magozurlinux ha scritto:
martedì 3 novembre 2020, 9:52
Prova a dare questo comando:

Codice: Seleziona tutto

echo REGDOMAIN=IT | sudo tee -a /etc/default/crda
riavvia il pc.
tutto uguale
Scrivi risposta

Ritorna a “Driver e periferiche”

Chi c’è in linea

Visualizzano questa sezione: Bing [Bot], DnD, Google [Bot], KCerci15, MARCO_1974 e 24 ospiti