Forum Ubuntu-it

Innanzitutto un salutone a tutti! Perchè sono nuovo del forum!
Vi spiego il mio problema!

Poki giorni fa ho tentato di installare Ubuntu su un hard disk esterno!

Non ci sono riuscito, anche perchè nn avevo tempo e quindi ho lasciato perdere!

Quando ho tentato questa Installazione avevo un solo Hard Disk sata WD 250Mb, e un hard disk esterno Lacie 80 Gb!
Tutti e due venivano riconosciuti dal processo di installazzione!!

Dopo un paio di giorni ho deciso di comprare un secondo hard disk SATA 2 Maxtor 160 Gb, sul quale inizialmente volevo installare Vista, ma poi durante l'uinstallazione il tutto si è interrotto per alcuni problemi!
Il tutto mi ha innervosito ( anche considerando i numerosi problemi che vista crea) e ho deciso di ritentare l'installazione di Ubuntu!

Questa volta ho deciso di installare Ubuntu sul secondo hard disk appena comprato (il tutto con il live cd di ubuntu 6.10 uscitomi dalla rivista PcProfessionale).

La cosa più assurda è che adesso Ubuntu in fase di installazione nn riconosce il nuovo hard disk, ma addirittura nn trova nemmeno il vecchio hard disk (dove c'è xp) che prima riconosceva tranquillamente.

In pratica mi dice che nn trova nessun hard disk, mentre le periferiche usb si, infatti se inserisco una pendrive subito viene rilevata.

Premetto che dopo il tentatavo di installazione di vista ho ricostruito Il MasterBootRecord di xp tramite la console di ripristino di xp riportando tutto come prima!

Ormai sono disperato, ho provato anche a staccare fisicamente il secondo hard disk, ma nulla nn trova nulla!

Cosa posso fare?

Come mai prima mi vedeva l'hard disk dove c'era xp, e ora nn solo nn vede questo ma nn vede nemmeno il nuovo?
Vi prego di aiutarmi perchè è la prima volta che tento di installare Linux, e quindi sono all'asciutto!

Grazie

che intendi con "non lo trova" ? Nel senso che non lo vedi sul desktop ?

Quello potrebbe essere normale. Prova a fare, da terminale

Codice: Seleziona tutto

sudo fdisk -l

e posta qui quello che dice

Ciao siryayo.

Prova anche questo comando da un terminale: (Applicazioni>Accessori>Terminale)

dmesg | less

con questo dovresti vedere tutto ciò che ti ha ricnonsciuto il kernel Linux dal boot in poi, inclusi i controller Ide Pata e Sata (visto come Scsi, tipo Sda) e tutti i Dischi e le unità Cd/Dvd-/+R/Rw collegate.

Con i tasti freccia e pageup e pagedown ti sposti, con q (sta per quit) esci.

Al più postaci parte di quello che il comando dmesg ti visualizza, almeno per capire cosa ti vede e cosa no.

Ciao.

by Ninja

ECCO FDISK

ubuntu@ubuntu:~$ sudo fdisk -1
fdisk: invalid option -- 1

Usage: fdisk [-b SSZ] [-u] DISK Change partition table
fdisk -l [-b SSZ] [-u] DISK List partition table(s)
fdisk -s PARTITION Give partition size(s) in blocks
fdisk -v Give fdisk version
Here DISK is something like /dev/hdb or /dev/sda
and PARTITION is something like /dev/hda7
-u: give Start and End in sector (instead of cylinder) units
-b 2048: (for certain MO disks) use 2048-byte sectors

ECCO DMESG....

Codice: Seleziona tutto

ubuntu@ubuntu:~$ dmesg less
[17179569.184000] Linux version 2.6.17-10-generic (root@vernadsky) (gcc version
4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #2 SMP Fri Oct 13 18:45:35
 UTC 2006 (Ubuntu 2.6.17-10.33-generic)
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000]  BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[17179569.184000]  BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[17179569.184000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[17179569.184000]  BIOS-e820: 0000000000100000 - 000000003fee0000 (usable)
[17179569.184000]  BIOS-e820: 000000003fee0000 - 000000003fee3000 (ACPI NVS)
[17179569.184000]  BIOS-e820: 000000003fee3000 - 000000003fef0000 (ACPI data)
[17179569.184000]  BIOS-e820: 000000003fef0000 - 000000003ff00000 (reserved)
[17179569.184000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[17179569.184000]  BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[17179569.184000] 126MB HIGHMEM available.
[17179569.184000] 896MB LOWMEM available.
[17179569.184000] found SMP MP-table at 000f3c50
[17179569.184000] On node 0 totalpages: 261856
[17179569.184000]   DMA zone: 4096 pages, LIFO batch:0
[17179569.184000]   Normal zone: 225280 pages, LIFO batch:31
[17179569.184000]   HighMem zone: 32480 pages, LIFO batch:7
[17179569.184000] DMI 2.3 present.
[17179569.184000] ACPI: RSDP (v002 FSC                                   ) @ 0x0
00f7b20
[17179569.184000] ACPI: XSDT (v001 FSC    PC       0x42302e31 AWRD 0x00000000) @
 0x3fee30c0
[17179569.184000] ACPI: FADT (v003 FSC    PC       0x42302e31 AWRD 0x00000000) @
 0x3fee9bc0
[17179569.184000] ACPI: SLIC (v001 FSC    PC       0x42302e31 AWRD 0x00000000) @
 0x3fee9e00
[17179569.184000] ACPI: MCFG (v001 FSC    PC       0x42302e31 AWRD 0x00000000) @
 0x3fee9fc0
[17179569.184000] ACPI: MADT (v001 FSC    PC       0x42302e31 AWRD 0x00000000) @
 0x3fee9d00
[17179569.184000] ACPI: DSDT (v001     00 AWRDACPI 0x00001000 MSFT 0x0100000e) @
 0x00000000
[17179569.184000] ACPI: PM-Timer IO Port: 0x408
[17179569.184000] ACPI: Local APIC address 0xfee00000
[17179569.184000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[17179569.184000] Processor #0 6:15 APIC version 20
[17179569.184000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[17179569.184000] Processor #1 6:15 APIC version 20
[17179569.184000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
[17179569.184000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[17179569.184000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[17179569.184000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
[17179569.184000] IOAPIC[0]: apic_id 4, version 3, address 0xfec00000, GSI 0-23
[17179569.184000] ACPI: IOAPIC (id[0x05] address[0xfecc0000] gsi_base[24])
[17179569.184000] IOAPIC[1]: apic_id 5, version 3, address 0xfecc0000, GSI 24-47
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[17179569.184000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[17179569.184000] ACPI: IRQ0 used by override.
[17179569.184000] ACPI: IRQ2 used by override.
[17179569.184000] ACPI: IRQ9 used by override.
[17179569.184000] Enabling APIC mode:  Flat.  Using 2 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information
[17179569.184000] Allocating PCI resources starting at 40000000 (gap: 3ff00000:a
0100000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/pr
eseed/kubuntu.seed boot=casper initrd=/casper/initrd.gz ramdisk_size=1048576 roo
t=/dev/ram rw quiet splash -- locale=it_IT console-setup/layoutcode=it
[17179569.184000] mapped APIC to ffffd000 (fee00000)
[17179569.184000] mapped IOAPIC to ffffc000 (fec00000)
[17179569.184000] mapped IOAPIC to ffffb000 (fecc0000)
[17179569.184000] Enabling fast FPU save and restore... done.
[17179569.184000] Enabling unmasked SIMD FPU exception support... done.
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[17179569.184000] Detected 1862.483 MHz processor.
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179570.308000] Dentry cache hash table entries: 131072 (order: 7, 524288 byte
s)
[17179570.308000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179570.332000] Memory: 1028444k/1047424k available (1910k kernel code, 18328k
 reserved, 1070k data, 308k init, 129920k highmem)
[17179570.332000] Checking if this processor honours the WP bit even in supervis
or mode... Ok.
[17179570.412000] Calibrating delay using timer specific routine.. 3727.45 BogoM
IPS (lpj=7454901)
[17179570.412000] Security Framework v1.0.0 initialized
[17179570.412000] SELinux:  Disabled at boot.
[17179570.412000] Mount-cache hash table entries: 512
[17179570.412000] CPU: After generic identify, caps: bfebfbff 20100000 00000000
00000000 0000e3bd 00000000 00000001
[17179570.412000] CPU: After vendor identify, caps: bfebfbff 20100000 00000000 0
0000000 0000e3bd 00000000 00000001
[17179570.412000] monitor/mwait feature present.
[17179570.412000] using mwait in idle threads.
[17179570.412000] CPU: L1 I cache: 32K, L1 D cache: 32K
[17179570.412000] CPU: L2 cache: 2048K
[17179570.412000] CPU: Hyper-Threading is disabled
[17179570.412000] CPU: After all inits, caps: bfebfbff 20100000 00000000 0000014
0 0000e3bd 00000000 00000001
[17179570.412000] Checking 'hlt' instruction... OK.
[17179570.428000] SMP alternatives: switching to UP code
[17179570.428000] checking if image is initramfs... it is
[17179570.892000] Freeing initrd memory: 5524k freed
[17179570.892000] ACPI: Core revision 20060707
[17179570.896000] ACPI: Looking for DSDT ... not found!
[17179570.900000] ACPI: System reset via FADT Reset Register is supported
[17179570.900000] machine_reset = acpi_machine_reset
[17179570.900000] CPU0: Intel(R) Core(TM)2 CPU          6300  @ 1.86GHz stepping
 06
[17179570.900000] SMP alternatives: switching to SMP code
[17179570.900000] Booting processor 1/1 eip 3000
[17179570.912000] Initializing CPU#1
[17179570.992000] Calibrating delay using timer specific routine.. 3724.31 BogoM
IPS (lpj=7448627)
[17179570.992000] CPU: After generic identify, caps: bfebfbff 20100000 00000000
00000000 0000e3bd 00000000 00000001
[17179570.992000] CPU: After vendor identify, caps: bfebfbff 20100000 00000000 0
0000000 0000e3bd 00000000 00000001
[17179570.992000] monitor/mwait feature present.
[17179570.992000] CPU: L1 I cache: 32K, L1 D cache: 32K
[17179570.992000] CPU: L2 cache: 2048K
[17179570.992000] CPU: Hyper-Threading is disabled
[17179570.992000] CPU: After all inits, caps: bfebfbff 20100000 00000000 0000014
0 0000e3bd 00000000 00000001
[17179570.992000] CPU1: Intel(R) Core(TM)2 CPU          6300  @ 1.86GHz stepping
 06
[17179570.992000] Total of 2 processors activated (7451.76 BogoMIPS).
[17179570.992000] ENABLING IO-APIC IRQs
[17179570.992000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[17179571.136000] checking TSC synchronization across 2 CPUs: passed.
[17179571.140000] Brought up 2 CPUs
[17179571.224000] migration_cost=4000
[17179571.224000] NET: Registered protocol family 16
[17179571.224000] EISA bus registered
[17179571.224000] ACPI: bus type pci registered
[17179571.224000] PCI: Using MMCONFIG
[17179571.224000] Setting up standard PCI resources
[17179571.224000] mtrr: your CPUs had inconsistent fixed MTRR settings
[17179571.224000] mtrr: probably your BIOS does not setup all CPUs.
[17179571.224000] mtrr: corrected configuration.
[17179571.236000] ACPI: Interpreter enabled
[17179571.236000] ACPI: Using IOAPIC for interrupt routing
[17179571.236000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[17179571.236000] PCI: Probing PCI hardware (bus 00)
[17179571.240000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:0f.1
[17179571.240000] Boot video device is 0000:02:00.0
[17179571.240000] PCI: Transparent bridge - 0000:00:13.1
[17179571.240000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[17179571.316000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEXG._PRT]
[17179571.320000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[17179571.320000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2PE._PRT]
[17179571.320000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2PB._PRT]
[17179571.320000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
[17179571.320000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
[17179571.320000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12)
[17179571.320000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 *11 12)
[17179571.320000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, di
sabled.
[17179571.320000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, di
sabled.
[17179571.320000] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, di
sabled.
[17179571.324000] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *5
[17179571.324000] Linux Plug and Play Support v0.97 (c) Adam Belay
[17179571.324000] pnp: PnP ACPI init
[17179571.328000] pnp: PnP ACPI: found 13 devices
[17179571.328000] PnPBIOS: Disabled by ACPI PNP
[17179571.328000] PCI: Using ACPI for IRQ routing
[17179571.328000] PCI: If a device doesn't work, try "pci=routeirq".  If it help
s, post a report
[17179571.328000] pnp: 00:01: ioport range 0x400-0x47f could not be reserved
[17179571.328000] pnp: 00:01: ioport range 0x500-0x50f has been reserved
[17179571.328000] PCI: Bridge: 0000:00:01.0
[17179571.328000]   IO window: c000-cfff
[17179571.328000]   MEM window: dfc00000-dfcfffff
[17179571.328000]   PREFETCH window: dfb00000-dfbfffff
[17179571.328000] PCI: Bridge: 0000:00:02.0
[17179571.328000]   IO window: b000-bfff
[17179571.328000]   MEM window: dc000000-deffffff
[17179571.328000]   PREFETCH window: c0000000-cfffffff
[17179571.328000] PCI: Bridge: 0000:00:03.0
[17179571.328000]   IO window: a000-afff
[17179571.328000]   MEM window: dfe00000-dfefffff
[17179571.328000]   PREFETCH window: dfd00000-dfdfffff
[17179571.328000] PCI: Bridge: 0000:00:13.0
[17179571.328000]   IO window: 9000-9fff
[17179571.328000]   MEM window: dfa00000-dfafffff
[17179571.328000]   PREFETCH window: df900000-df9fffff
[17179571.328000] PCI: Bridge: 0000:00:13.1
[17179571.328000]   IO window: 8000-8fff
[17179571.328000]   MEM window: df800000-df8fffff
[17179571.328000]   PREFETCH window: df700000-df7fffff
[17179571.328000] PCI: Setting latency timer of device 0000:00:01.0 to 64
[17179571.328000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 27 (level, low) ->
IRQ 169
[17179571.328000] PCI: Via IRQ fixup for 0000:00:02.0, from 5 to 9
[17179571.328000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[17179571.328000] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 31 (level, low) ->
IRQ 177
[17179571.328000] PCI: Via IRQ fixup for 0000:00:03.0, from 5 to 1
[17179571.328000] PCI: Setting latency timer of device 0000:00:03.0 to 64
[17179571.328000] PCI: Setting latency timer of device 0000:00:13.0 to 64
[17179571.328000] PCI: Setting latency timer of device 0000:00:13.1 to 64
[17179571.328000] NET: Registered protocol family 2
[17179571.364000] IP route cache hash table entries: 32768 (order: 5, 131072 byt
es)
[17179571.364000] TCP established hash table entries: 131072 (order: 8, 1048576
bytes)
[17179571.364000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[17179571.364000] TCP: Hash tables configured (established 131072 bind 65536)
[17179571.364000] TCP reno registered
[17179571.364000] audit: initializing netlink socket (disabled)
[17179571.364000] audit(1174307231.364:1): initialized
[17179571.364000] highmem bounce pool size: 64 pages
[17179571.364000] VFS: Disk quotas dquot_6.5.1
[17179571.364000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[17179571.364000] Initializing Cryptographic API
[17179571.364000] io scheduler noop registered
[17179571.364000] io scheduler anticipatory registered
[17179571.364000] io scheduler deadline registered
[17179571.364000] io scheduler cfq registered (default)
[17179571.364000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 27 (level, low) ->
IRQ 169
[17179571.364000] PCI: Setting latency timer of device 0000:00:02.0 to 64
[17179571.364000] assign_interrupt_mode Found MSI capability
[17179571.364000] Allocate Port Service[0000:00:02.0:pcie00]
[17179571.364000] Allocate Port Service[0000:00:02.0:pcie01]
[17179571.364000] Allocate Port Service[0000:00:02.0:pcie02]
[17179571.364000] Allocate Port Service[0000:00:02.0:pcie03]
[17179571.364000] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 31 (level, low) ->
IRQ 177
[17179571.364000] PCI: Setting latency timer of device 0000:00:03.0 to 64
[17179571.364000] assign_interrupt_mode Found MSI capability
[17179571.364000] Allocate Port Service[0000:00:03.0:pcie00]
[17179571.364000] Allocate Port Service[0000:00:03.0:pcie01]
[17179571.364000] Allocate Port Service[0000:00:03.0:pcie02]
[17179571.364000] Allocate Port Service[0000:00:03.0:pcie03]
[17179571.364000] isapnp: Scanning for PnP cards...
[17179571.720000] isapnp: No Plug & Play device found
[17179571.736000] Real Time Clock Driver v1.12ac
[17179571.736000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ shari
ng enabled
[17179571.736000] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179571.736000] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[17179571.736000] ACPI: PCI Interrupt 0000:05:04.0[A] -> GSI 17 (level, low) ->
IRQ 209
[17179571.736000] 0000:05:04.0: ttyS1 at I/O 0x8c08 (irq = 209) is a 16450
[17179571.736000] 0000:05:04.0: ttyS2 at I/O 0x8c10 (irq = 209) is a 8250
[17179571.736000] 0000:05:04.0: ttyS3 at I/O 0x8c18 (irq = 209) is a 16450
[17179571.736000] Couldn't register serial port 0000:05:04.0: -28
[17179571.736000] mice: PS/2 mouse device common for all mice
[17179571.736000] RAMDISK driver initialized: 16 RAM disks of 1048576K size 1024
 blocksize
[17179571.736000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[17179571.736000] ide: Assuming 33MHz system bus speed for PIO modes; override w
ith idebus=xx
[17179571.736000] PNP: No PS/2 controller found. Probing ports directly.
[17179571.740000] serio: i8042 AUX port at 0x60,0x64 irq 12
[17179571.740000] serio: i8042 KBD port at 0x60,0x64 irq 1
[17179571.740000] EISA: Probing bus 0 at eisa.0
[17179571.740000] Cannot allocate resource for EISA slot 8
[17179571.740000] EISA: Detected 0 cards.
[17179571.740000] TCP bic registered
[17179571.740000] NET: Registered protocol family 1
[17179571.740000] NET: Registered protocol family 8
[17179571.740000] NET: Registered protocol family 20
[17179571.740000] Starting balanced_irq
[17179571.740000] Using IPI No-Shortcut mode
[17179571.740000] ACPI: (supports S0 S3 S4 S5)
[17179571.740000] Freeing unused kernel memory: 308k freed
[17179572.804000] Capability LSM initialized
[17179572.828000] ACPI: Fan [FAN] (on)
[17179572.832000] ACPI Exception (acpi_processor-0693): AE_NOT_FOUND, Processor
Device is not present [20060707]
[17179572.832000] ACPI: Getting cpuindex for acpiid 0x2
[17179572.832000] ACPI Exception (acpi_processor-0693): AE_NOT_FOUND, Processor
Device is not present [20060707]
[17179572.832000] ACPI: Getting cpuindex for acpiid 0x3
[17179572.832000] ACPI: Thermal Zone [THRM] (34 C)
[17179573.164000] VP_IDE: IDE controller at PCI slot 0000:00:0f.1
[17179573.164000] PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 0
[17179573.164000] VP_IDE: chipset revision 7
[17179573.164000] VP_IDE: not 100% native mode: will probe irqs later
[17179573.164000] VP_IDE: VIA vt8237a (rev 00) IDE UDMA133 controller on pci0000
:00:0f.1
[17179573.164000]     ide0: BM-DMA at 0xe400-0xe407, BIOS settings: hda:pio, hdb
:pio
[17179573.164000]     ide1: BM-DMA at 0xe408-0xe40f, BIOS settings: hdc:DMA, hdd
:pio
[17179573.164000] Probing IDE interface ide0...
[17179573.732000] Probing IDE interface ide1...
[17179574.600000] hdc: Optiarc DVD RW AD-7170A, ATAPI CD/DVD-ROM drive
[17179575.276000] ide1 at 0x170-0x177,0x376 on irq 15
[17179575.284000] hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache,
UDMA(33)
[17179575.284000] Uniform CD-ROM driver Revision: 3.20
[17179578.024000] Probing IDE interface ide0...
[17179578.052000] usbcore: registered new driver usbfs
[17179578.052000] usbcore: registered new driver hub
[17179578.056000] USB Universal Host Controller Interface driver v3.0
[17179578.056000] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) ->
IRQ 217
[17179578.056000] PCI: Via IRQ fixup for 0000:00:10.0, from 10 to 9
[17179578.056000] uhci_hcd 0000:00:10.0: UHCI Host Controller
[17179578.056000] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus nu
mber 1
[17179578.056000] uhci_hcd 0000:00:10.0: irq 217, io base 0x0000e000
[17179578.056000] usb usb1: configuration #1 chosen from 1 choice
[17179578.056000] hub 1-0:1.0: USB hub found
[17179578.056000] hub 1-0:1.0: 2 ports detected
[17179578.100000] ieee1394: Initialized config rom entry `ip1394'
[17179578.160000] ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 22 (level, low) ->
IRQ 225
[17179578.160000] PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 1
[17179578.160000] uhci_hcd 0000:00:10.1: UHCI Host Controller
[17179578.160000] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus nu
mber 2
[17179578.160000] uhci_hcd 0000:00:10.1: irq 225, io base 0x0000dc00
[17179578.160000] usb usb2: configuration #1 chosen from 1 choice
[17179578.160000] hub 2-0:1.0: USB hub found
[17179578.160000] hub 2-0:1.0: 2 ports detected
[17179578.264000] ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) ->
IRQ 233
[17179578.264000] PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 9
[17179578.264000] uhci_hcd 0000:00:10.2: UHCI Host Controller
[17179578.264000] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus nu
mber 3
[17179578.264000] uhci_hcd 0000:00:10.2: irq 233, io base 0x0000d800
[17179578.264000] usb usb3: configuration #1 chosen from 1 choice
[17179578.264000] hub 3-0:1.0: USB hub found
[17179578.264000] hub 3-0:1.0: 2 ports detected
[17179578.368000] ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 23 (level, low) ->
IRQ 50
[17179578.368000] PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 2
[17179578.368000] uhci_hcd 0000:00:10.3: UHCI Host Controller
[17179578.368000] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus nu
mber 4
[17179578.368000] uhci_hcd 0000:00:10.3: irq 50, io base 0x0000d400
[17179578.372000] usb usb4: configuration #1 chosen from 1 choice
[17179578.372000] hub 4-0:1.0: USB hub found
[17179578.372000] hub 4-0:1.0: 2 ports detected
[17179578.476000] ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) ->
IRQ 233
[17179578.476000] PCI: Via IRQ fixup for 0000:00:10.4, from 10 to 9
[17179578.476000] ehci_hcd 0000:00:10.4: EHCI Host Controller
[17179578.476000] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus nu
mber 5
[17179578.476000] ehci_hcd 0000:00:10.4: irq 233, io mem 0xdffff000
[17179578.476000] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 D
ec 2004
[17179578.476000] usb usb5: configuration #1 chosen from 1 choice
[17179578.476000] hub 5-0:1.0: USB hub found
[17179578.476000] hub 5-0:1.0: 8 ports detected
[17179578.580000] ACPI: PCI Interrupt 0000:05:06.0[A] -> GSI 19 (level, low) ->
IRQ 58
[17179578.580000] PCI: Via IRQ fixup for 0000:05:06.0, from 11 to 10
[17179578.632000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[58]  MMIO=[df8fe
000-df8fe7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[17179579.428000] usb 5-4: new high speed USB device using ehci_hcd and address
2
[17179579.652000] usb 5-4: configuration #1 chosen from 1 choice
[17179579.892000] usb 5-5: new high speed USB device using ehci_hcd and address
3
[17179579.912000] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0010dc00010b1428
]
[17179580.024000] usb 5-5: configuration #1 chosen from 1 choice
[17179580.024000] hub 5-5:1.0: USB hub found
[17179580.024000] hub 5-5:1.0: 4 ports detected
[17179580.368000] usb 5-7: new high speed USB device using ehci_hcd and address
4
[17179580.500000] usb 5-7: configuration #1 chosen from 1 choice
[17179580.500000] hub 5-7:1.0: USB hub found
[17179580.500000] hub 5-7:1.0: 7 ports detected
[17179580.820000] usb 5-5.2: new full speed USB device using ehci_hcd and addres
s 5
[17179580.932000] usb 5-5.2: configuration #1 chosen from 1 choice
[17179580.932000] usbcore: registered new driver libusual
[17179580.936000] SCSI subsystem initialized
[17179580.936000] Initializing USB Mass Storage driver...
[17179580.940000] scsi0 : SCSI emulation for USB Mass Storage devices
[17179580.940000] usb-storage: device found at 2
[17179580.940000] usb-storage: waiting for device to settle before scanning
[17179581.132000] usb 5-7.1: new low speed USB device using ehci_hcd and address
 6
[17179581.172000] ISO 9660 Extensions: Microsoft Joliet Level 3
[17179581.200000] ISO 9660 Extensions: RRIP_1991A
[17179581.244000] usb 5-7.1: configuration #1 chosen from 1 choice
[17179581.244000] Registering unionfs 1.1.4
[17179581.248000] loop: loaded (max 8 devices)
[17179581.444000] usb 5-7.2: new high speed USB device using ehci_hcd and addres
s 7
[17179581.620000] usb 5-7.2: configuration #1 chosen from 1 choice
[17179581.820000] usb 5-7.6: new low speed USB device using ehci_hcd and address
 8
[17179581.920000] usb 5-7.6: configuration #1 chosen from 1 choice
[17179581.920000] scsi1 : SCSI emulation for USB Mass Storage devices
[17179581.920000] usbcore: registered new driver usb-storage
[17179581.920000] USB Mass Storage support registered.
[17179581.920000] usb-storage: device found at 5
[17179581.920000] usb-storage: waiting for device to settle before scanning
[17179581.920000] usbcore: registered new driver hiddev
[17179581.932000] input:   USB Keyboard as /class/input/input0
[17179581.932000] input: USB HID v1.10 Keyboard [  USB Keyboard] on usb-0000:00:
10.4-7.1
[17179581.948000] input:   USB Keyboard as /class/input/input1
[17179581.948000] input: USB HID v1.10 Device [  USB Keyboard] on usb-0000:00:10
.4-7.1
[17179581.952000] input: Logitech USB Mouse as /class/input/input2
[17179581.952000] input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00
:10.4-7.6
[17179581.952000] usbcore: registered new driver usbhid
[17179581.952000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[17179582.080000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[17179585.944000] usb-storage: device scan complete
[17179585.972000]   Vendor: Generic   Model: 2.0 Reader   -CF  Rev: 1.20
[17179585.972000]   Type:   Direct-Access                      ANSI SCSI revisio
n: 00
[17179586.004000]   Vendor: Generic   Model: 2.0 Reader   -SM  Rev: 1.20
[17179586.004000]   Type:   Direct-Access                      ANSI SCSI revisio
n: 00
[17179586.032000]   Vendor: Generic   Model: 2.0 Reader   -SD  Rev: 1.20
[17179586.032000]   Type:   Direct-Access                      ANSI SCSI revisio
n: 00
[17179586.064000]   Vendor: Generic   Model: 2.0 Reader   -MS  Rev: 1.20
[17179586.064000]   Type:   Direct-Access                      ANSI SCSI revisio
n: 00
[17179586.096000]   Vendor: Generic   Model: 2.0 Reader   -xD  Rev: 1.20
[17179586.096000]   Type:   Direct-Access                      ANSI SCSI revisio
n: 00
[17179586.108000] sd 0:0:0:0: Attached scsi removable disk sda
[17179586.112000] sd 0:0:0:1: Attached scsi removable disk sdb
[17179586.116000] sd 0:0:0:2: Attached scsi removable disk sdc
[17179586.120000] sd 0:0:0:3: Attached scsi removable disk sdd
[17179586.124000] sd 0:0:0:4: Attached scsi removable disk sde
[17179586.920000] usb-storage: device scan complete
[17179586.920000]   Vendor: HP        Model: Photosmart 2610   Rev: 1.00
[17179586.920000]   Type:   Direct-Access                      ANSI SCSI revisio
n: 02
[17179586.920000] sd 1:0:0:0: Attached scsi removable disk sdf
[17179604.904000] via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald B
ecker
[17179604.904000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) ->
IRQ 50
[17179604.904000] PCI: Via IRQ fixup for 0000:00:12.0, from 10 to 2
[17179604.908000] eth0: VIA Rhine II at 0x1d000, 00:16:17:e3:87:d2, IRQ 50.
[17179604.912000] eth0: MII PHY found at address 1, status 0x786d advertising 01
e1 Link 4de1.
[17179613.548000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[17179613.832000] input: PC Speaker as /class/input/input3
[17179613.948000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[17179614.452000] Linux agpgart interface v0.101 (c) Dave Jones
[17179614.496000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer d
ev 5 if 1 alt 0 proto 2 vid 0x03F0 pid 0x4511
[17179614.496000] usbcore: registered new driver usblp
[17179614.496000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class dri
ver
[17179614.700000] eth0: link up, 100Mbps, full-duplex, lpa 0x4DE1
[17179614.776000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[17179614.776000] sd 0:0:0:1: Attached scsi generic sg1 type 0
[17179614.776000] sd 0:0:0:2: Attached scsi generic sg2 type 0
[17179614.780000] sd 0:0:0:3: Attached scsi generic sg3 type 0
[17179614.780000] sd 0:0:0:4: Attached scsi generic sg4 type 0
[17179614.780000] sd 1:0:0:0: Attached scsi generic sg5 type 0
[17179614.836000] ACPI: PCI Interrupt 0000:04:01.0[A] -> GSI 17 (level, low) ->
IRQ 209
[17179614.836000] PCI: Via IRQ fixup for 0000:04:01.0, from 11 to 1
[17179614.836000] PCI: Setting latency timer of device 0000:04:01.0 to 64
[17179614.884000] ts: Compaq touchscreen protocol output
[17179615.220000] hda_codec: Unknown model for ALC883, trying auto-probe from BI
OS...
[17179615.968000] NET: Registered protocol family 17
[17179618.364000] NET: Registered protocol family 10
[17179618.364000] lo: Disabled Privacy Extensions
[17179618.364000] IPv6 over IPv4 tunneling driver
[17179622.504000] ACPI: Power Button (FF) [PWRF]
[17179622.504000] ACPI: Power Button (CM) [PWRB]
[17179622.504000] ACPI: Sleep Button (CM) [SLPB]
[17179622.620000] ibm_acpi: ec object not found
[17179622.684000] pcc_acpi: loading...
[17179625.048000] lp: driver loaded but no devices found
[17179625.256000] ppdev: user-space parallel port driver
[17179628.516000] eth0: no IPv6 routers present
[17179634.636000] apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
[17179634.636000] apm: disabled - APM is not SMP safe.
[17179648.800000] Bluetooth: Core ver 2.8
[17179648.800000] NET: Registered protocol family 31
[17179648.800000] Bluetooth: HCI device and connection manager initialized
[17179648.800000] Bluetooth: HCI socket layer initialized
[17179649.088000] Bluetooth: L2CAP ver 2.8
[17179649.088000] Bluetooth: L2CAP socket layer initialized
[17179649.112000] Bluetooth: RFCOMM socket layer initialized
[17179649.112000] Bluetooth: RFCOMM TTY layer initialized
[17179649.112000] Bluetooth: RFCOMM ver 1.7
[17179676.732000] hda-intel: Invalid position buffer, using LPIB read method ins

Codice: Seleziona tutto

sudo fdisk -l

è una elle non un uno....

si scusa una l......se no nn veniva fuori tutto quel casino

siryayo ha scritto:
[17179569.184000] Linux version 2.6.17-10-generic è la versione del tuo kernel Linux

(root@vernadsky) (gcc version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #2 SMP Fri Oct 13 18:45:35 UTC 2006 (Ubuntu
2.6.17-10.33-generic)[17179569.184000] BIOS-provided physical RAM map:
...
...
[17179569.184000] Enabling APIC mode: Flat. Using 2 I/O APICs
[17179569.184000] Using ACPI (MADT) for SMP configuration information l'ACPI è l'interfaccia del BIOS per gestire l'alimentazione
....
....
[17179569.184000] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/kubuntu.seed
boot=casper initrd=/casper/initrd.gz ramdisk_size=1048576 root=/dev/ram rw quiet splash -- locale=it_IT console-setup/layoutcode=it
sopra i parametri passati al kernel all'avvio
[17179569.184000] Enabling fast FPU save and restore... done. abilitazione all'elaborazione in hardware dei numeri reali
[17179569.184000] Enabling unmasked SIMD FPU exception support... done.
[17179569.184000] Initializing CPU#0 inizializza il 1° processore
[17179569.184000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[17179569.184000] Detected 1862.483 MHz processor. la frequenza del tuo processore
[17179569.184000] Using pmtmr for high-res timesource
[17179569.184000] Console: colour VGA+ 80x25
[17179570.308000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[17179570.308000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[17179570.332000] Memory: 1028444k/1047424k available (1910k kernel code, 18328k Dovresti avere 1 GB di Ram
reserved, 1070k data, 308k init, 129920k highmem)
...
...
[17179570.412000] CPU: L1 I cache: 32K, L1 D cache: 32K la memoria cache di 1° livello del tuo processore
[17179570.412000] CPU: L2 cache: 2048K e quella di 2° livello
[17179570.412000] CPU: Hyper-Threading is disabled Hyper-Threading (tecnologia Intel) disattivato
[17179570.412000] CPU: After all inits, caps: bfebfbff 20100000 00000000 0000014
0 0000e3bd 00000000 00000001
[17179570.412000] Checking 'hlt' instruction... OK.
[17179570.428000] SMP alternatives: switching to UP code riconosce una configurazione multiprocessore
...
...
[17179570.900000] CPU0: Intel(R) Core(TM)2 CPU 6300 @ 1.86GHz stepping 06 il tuo processore
[17179570.900000] SMP alternatives: switching to SMP code
[17179570.900000] Booting processor 1/1 eip 3000
[17179570.912000] Initializing CPU#1 inizializza anche il 2° processore
...
...
[17179570.992000] CPU: L1 I cache: 32K, L1 D cache: 32K riconosce la memoria cache anche del 2° processore
[17179570.992000] CPU: L2 cache: 2048K
[17179570.992000] CPU: Hyper-Threading is disabled
...
[17179570.992000] CPU1: Intel(R) Core(TM)2 CPU 6300 @ 1.86GHz stepping 06 ed ecco riconosciuto il 2° processore, il 2° core
[17179570.992000] Total of 2 processors activated (7451.76 BogoMIPS).
[17179570.992000] ENABLING IO-APIC IRQs
...
...
[17179571.328000] PCI: Bridge: 0000:00:01.0 incomincia a riconoscere il bus pci
[17179571.328000] IO window: c000-cfff
[17179571.328000] MEM window: dfc00000-dfcfffff
[17179571.328000] PREFETCH window: dfb00000-dfbfffff
[17179571.328000] PCI: Bridge: 0000:00:02.0
[17179571.328000] IO window: b000-bfff
...
...
...
[17179573.164000] VP_IDE: IDE controller at PCI slot 0000:00:0f.1 è ora il controller IDE
[17179573.164000] PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 0
[17179573.164000] VP_IDE: chipset revision 7
[17179573.164000] VP_IDE: not 100% native mode: will probe irqs later
[17179573.164000] VP_IDE: VIA vt8237a (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 chipset Via vt8237
[17179573.164000] ide0: BM-DMA at 0xe400-0xe407, BIOS settings: hda:pio, hdb:pio riconosciuto il 1° canale IDE, sempra non trovi nulla
[17179573.164000] ide1: BM-DMA at 0xe408-0xe40f, BIOS settings: hdc:DMA, hdd:pio ora il 2° canale, sembra trovi qualcosa come master
[17179573.164000] Probing IDE interface ide0...
[17179573.732000] Probing IDE interface ide1...
[17179574.600000] hdc: Optiarc DVD RW AD-7170A, ATAPI CD/DVD-ROM drive ecco il master del 2° canale, il masterizzatore dvd
[17179575.276000] ide1 at 0x170-0x177,0x376 on irq 15
[17179575.284000] hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache,UDMA(33) però usa solo l'DMA33, di solito usano il 66, non è che hai messo il cavo a 40 poli?
[17179575.284000] Uniform CD-ROM driver Revision: 3.20
[17179578.024000] Probing IDE interface ide0...
[17179578.052000] usbcore: registered new driver usbfs E qua comincia con l'usb
[17179578.052000] usbcore: registered new driver hub
[17179578.056000] USB Universal Host Controller Interface driver v3.0
[17179578.056000] ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) ->
IRQ 217
[17179578.056000] PCI: Via IRQ fixup for 0000:00:10.0, from 10 to 9
[17179578.056000] uhci_hcd 0000:00:10.0: UHCI Host Controller
[17179578.056000] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus nu
mber 1
[17179578.056000] uhci_hcd 0000:00:10.0: irq 217, io base 0x0000e000
[17179578.056000] usb usb1: configuration #1 chosen from 1 choice
[17179578.056000] hub 1-0:1.0: USB hub found
[17179578.056000] hub 1-0:1.0: 2 ports detected
[17179578.100000] ieee1394: Initialized config rom entry `ip1394' il firewire, detto anche i-link, per collegare la telecamera mini-Dv
...
...
[17179580.932000] usb 5-5.2: configuration #1 chosen from 1 choice trova qualcosa su un bus usb
[17179580.932000] usbcore: registered new driver libusual
[17179580.936000] SCSI subsystem initialized inizializza il sottosistema Scsi
[17179580.936000] Initializing USB Mass Storage driver... perché è un dispositivo di archiviazione (memoria di massa)
[17179580.940000] scsi0 : SCSI emulation for USB Mass Storage devices abilita l'emulazione Scsi per il dispositivo trovato (quindi lo vedi come disco fisso Scsi)
...
...
[17179581.920000] scsi1 : SCSI emulation for USB Mass Storage devices ne trova ed abilita un'altro
[17179581.920000] usbcore: registered new driver usb-storage
[17179581.920000] USB Mass Storage support registered.
[17179581.920000] usb-storage: device found at 5
[17179581.920000] usb-storage: waiting for device to settle before scanning
[17179581.920000] usbcore: registered new driver hiddev
[17179581.932000] input: USB Keyboard as /class/input/input0 inoltre trova tastiera e mouse usb
[17179581.932000] input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-0000:00:10.4-7.1
[17179581.948000] input: USB Keyboard as /class/input/input1
[17179581.948000] input: USB HID v1.10 Device [ USB Keyboard] on usb-0000:00:10.4-7.1
[17179581.952000] input: Logitech USB Mouse as /class/input/input2
[17179581.952000] input: USB HID v1.10 Mouse [Logitech USB Mouse] on usb-0000:00:10.4-7.6
[17179581.952000] usbcore: registered new driver usbhid
[17179581.952000] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[17179582.080000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[17179585.944000] usb-storage: device scan complete
[17179585.972000] Vendor: Generic Model: 2.0 Reader -CF Rev: 1.20 Sembra abbia trovato un lettore di schede
[17179585.972000] Type: Direct-Access ANSI SCSI revision: 00
[17179586.004000] Vendor: Generic Model: 2.0 Reader -SM Rev: 1.20
[17179586.004000] Type: Direct-Access ANSI SCSI revision: 00
[17179586.032000] Vendor: Generic Model: 2.0 Reader -SD Rev: 1.20
[17179586.032000] Type: Direct-Access ANSI SCSI revision: 00
[17179586.064000] Vendor: Generic Model: 2.0 Reader -MS Rev: 1.20
[17179586.064000] Type: Direct-Access ANSI SCSI revision: 00
[17179586.096000] Vendor: Generic Model: 2.0 Reader -xD Rev: 1.20
[17179586.096000] Type: Direct-Access ANSI SCSI revision: 00
[17179586.108000] sd 0:0:0:0: Attached scsi removable disk sda questi sono i dispositivi Scsi creati per accedere ai supporti
[17179586.112000] sd 0:0:0:1: Attached scsi removable disk sdb
[17179586.116000] sd 0:0:0:2: Attached scsi removable disk sdc
[17179586.120000] sd 0:0:0:3: Attached scsi removable disk sdd
[17179586.124000] sd 0:0:0:4: Attached scsi removable disk sde
[17179586.920000] usb-storage: device scan complete
[17179586.920000] Vendor: HP Model: Photosmart 2610 Rev: 1.00 Continua con la macchina fotografica HP
[17179586.920000] Type: Direct-Access ANSI SCSI revision: 02
[17179586.920000] sd 1:0:0:0: Attached scsi removable disk sdf vista anche questa col supporto Scsi
[17179604.904000] via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker mi sembra di ricordare una scheda di rete
[17179604.904000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 23 (level, low) ->
IRQ 50
[17179604.904000] PCI: Via IRQ fixup for 0000:00:12.0, from 10 to 2
[17179604.908000] eth0: VIA Rhine II at 0x1d000, 00:16:17:e3:87:d2, IRQ 50. infatti eccola
[17179604.912000] eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 4de1.
...
...
[17179614.496000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 5 if 1 alt 0 proto 2 vid 0x03F0 pid 0x4511
[17179614.496000] usbcore: registered new driver usblp i driver per il supporto alle stampanti usb
[17179614.496000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[17179614.700000] eth0: link up, 100Mbps, full-duplex, lpa 0x4DE1 la modalità della scheda di rete
[17179614.776000] sd 0:0:0:0: Attached scsi generic sg0 type 0 riecco i "dischi" Scsi, ovvero disco, lettore di schede e macchinetta fotografica
[17179614.776000] sd 0:0:0:1: Attached scsi generic sg1 type 0
[17179614.776000] sd 0:0:0:2: Attached scsi generic sg2 type 0
[17179614.780000] sd 0:0:0:3: Attached scsi generic sg3 type 0
[17179614.780000] sd 0:0:0:4: Attached scsi generic sg4 type 0
[17179614.780000] sd 1:0:0:0: Attached scsi generic sg5 type 0
...
...
[17179648.800000] Bluetooth: Core ver 2.8 vengono precaricati i moduli per il bluetooth
[17179648.800000] NET: Registered protocol family 31
[17179648.800000] Bluetooth: HCI device and connection manager initialized
[17179648.800000] Bluetooth: HCI socket layer initialized
[17179649.088000] Bluetooth: L2CAP ver 2.8
[17179649.088000] Bluetooth: L2CAP socket layer initialized
[17179649.112000] Bluetooth: RFCOMM socket layer initialized
[17179649.112000] Bluetooth: RFCOMM TTY layer initialized
[17179649.112000] Bluetooth: RFCOMM ver 1.7
[17179676.732000] hda-intel: Invalid position buffer, using LPIB read method ins

Se ho sbagliato qualcosa sui commenti, dimmelo pure.

Per quello che riguarda il SATA, non ce né traccia, sei sicuro di non averlo disabilitato dal BIOS?
Secondo me è la cosa più semplice che può esserti capitata.
Infatti il kernel non ti trova nemmeno il controller, non solo i dischi, se lo trovasse e non lo riconoscesse, troveremmo lo stesso qualcosa, qualche messaggio...
...quindi è come se non ci fosse, la cosa più facile è che tu l'abbia disabilitato.

Guarda quindi nel menù del BIOS.

by Ninja

Scusa aggiungo qualche riga del mio "dmesg" così vedi come mi viene riconosciuto il Sata e i miei 2 dischi fissi:

[17179574.772000] PCI: Via IRQ fixup for 0000:00:0f.0, from 10 to 9
[17179574.772000] sata_via 0000:00:0f.0: routed to hard irq line 9
[17179574.772000] ata1: SATA max UDMA/133 cmd 0xD000 ctl 0xC802 bmdma 0xB800 irq 169
[17179574.772000] ata2: SATA max UDMA/133 cmd 0xC400 ctl 0xC002 bmdma 0xB808 irq 169
[17179574.936000] ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4063 85:7c69 86:3e01 87:4063 88:407f
[17179574.936000] ata1: dev 0 ATA-7, max UDMA/133, 398297088 sectors: LBA48
[17179574.948000] ata1: dev 0 configured for UDMA/133
[17179574.948000] scsi0 : sata_via
[17179575.116000] ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4063 85:7c69 86:3e01 87:4063 88:407f
[17179575.116000] ata2: dev 0 ATA-7, max UDMA/133, 398297088 sectors: LBA48
[17179575.128000] ata2: dev 0 configured for UDMA/133
[17179575.128000] scsi1 : sata_via
[17179575.132000] Vendor: ATA Model: Maxtor 6B200M0 Rev: BANC
[17179575.132000] Type: Direct-Access ANSI SCSI revision: 05
[17179575.132000] Vendor: ATA Model: Maxtor 6B200M0 Rev: BANC
[17179575.132000] Type: Direct-Access ANSI SCSI revision: 05
[17179575.140000] SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
[17179575.140000] sda: Write Protect is off
[17179575.140000] sda: Mode Sense: 00 3a 00 00
[17179575.140000] SCSI device sda: drive cache: write back
[17179575.140000] SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
[17179575.140000] sda: Write Protect is off
[17179575.140000] sda: Mode Sense: 00 3a 00 00
[17179575.140000] SCSI device sda: drive cache: write back
[17179575.140000] sda: sda1 sda2
[17179575.264000] sd 0:0:0:0: Attached scsi disk sda
[17179575.264000] SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
[17179575.264000] sdb: Write Protect is off
[17179575.264000] sdb: Mode Sense: 00 3a 00 00
[17179575.264000] SCSI device sdb: drive cache: write back
[17179575.264000] SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
[17179575.264000] sdb: Write Protect is off
[17179575.264000] sdb: Mode Sense: 00 3a 00 00
[17179575.264000] SCSI device sdb: drive cache: write back
[17179575.264000] sdb: sdb1 sdb2
[17179575.388000] sd 1:0:0:0: Attached scsi disk sdb

Ecco, questi sono i miei due dischi sata, due Maxtor da 200 GB, come vedi mi vengono rilevate anche le partizioni.

Ciao.

E' chiaro che nn sono disabilitati nel bios!!!

Da win xp li uso tutti e due tranquillamente!!!!
E li ho formattati con gparted che li vede tutti e due tranquillamente!!
E' solo quando avvio un sistema operativo linux da live cd che nn mi vede nulla!!!!
come se nn li caricasse

2 cose:

1) quando posti cose lunghe, potresti metterle in un blocco "codice" in modo da occupare meno spazio per ogni post ? Così diventa più facile da leggere

2)

Codice: Seleziona tutto

sudo fdisk -l

Cmq per la questione del bios.....nn è mai statao toccato......se la prima volta mi vedeva l'hard disk c, e ora nn me lo vede dovrebbe essere un prob software credo!

Puo essere che quando hai montato l'hard disk (lo so perchè mi è successo) hai messo male un jumper (quello che decide se master o slave) e alcune volte va, altre no... a me prima di accorgermene è passata una settimana

ma gli hard disk SATA NN VANNO SETTATI COME MASTER O SLAVE!

C'è solo un jumper e mi pare che serve per la velocità di trasmissione

Udite Udite!!

Sono andato nel bios per fare una prova!!!

Il settaggio originale è il seguente :

1) SATA Controller (enabled)
2) SATA Controller Mode (Ide)

Ho provato a cambiare la seconda opzione in (RAID) e miracolo!!!! Ubuntu mi trova tutti e 2 gli hard disk SATA in fase di installazione!

Ora il problema è che all'avvio Linux nn mi dice qualcosa riguardo al RAID CHE NN è INSTALLATO, e se lo voglio installare mi prega di nn usare qualcosa......qualcosa che nn sono riuscito a leggere perchè la schermata è velocissima!

Inoltre se chiudo l'installazione e riavvio il pc per entrare in Xp (sempre col settaggio "SATA CONTROLLER MODE IN (RAID), si blocca e ritorna sempre alla schermata del bios, è UN CICLO SENZA FINE insomma!!
Per far ripartire xp devo reimpostare il bios come "ide"!!

Ora vi chiedo, cosa posso o devo fare?

Come si installa questo raid, che vada bene per farmi installare sia linux, sia farmi avviare Xp come sistema operativo di default?

Grazie

Ciao siryayo.

E' la prima volta che mi capita di sentire una cosa simile, però non è impossibile.

Il raid è una funzione che permette di utilizzare più dischi fissi come se fossero un'unica unità di memorizzazione.

I vantaggi possono essere molti, maggiori prestazioni in lettura e scrittura, maggiore sicurezza dei dati (eccetto il raid 0 che risulta, al contrario delle altre configurazioni, più insicuro dell'uso di un solo disco fisso ma in teoria dovrebbe essere molto più veloce).

Per avere un'idea più precisa: http://it.wikipedia.org/wiki/RAID

Secondo me, l'opzione "Sata Controller Mode" in "Ide" è corretta, infatti si sconsiglia l'uso di soluzioni Raid ibride (in parte software ed in parte hardware, quelle dei controller "economici" inseriti sulle schede madri), per fare il Raid meglio usare o il soluzioni hardware (costoso perché nel 99% dei casi si usa un controller Scsi e quindi anche i dischi sono Scsi, le soluzioni Ide ci sono ma sono poche e con maggiori limitazioni) o software (per farlo si può utilizzare una funzionalità del kernel Linux) che permette la creazione di un raid in modo molto più flessibile rispetto all'hardware (con uso di periferiche miste, che utilizzano tecnologie differenti ad es. Ide Pata, Sata, Scsi, Usb, ecc...).

Quindi ti consiglierei (se te la senti) l'aggiornamento del Bios della scheda madre, nella speranza che ti risolva il problema.

Vorrei farti una domanda, se non ti dispiace, che scheda madre hai? (purtroppo dal "dmesg" non si capisce)

Ciao.

by Ninja

La scheda madre è MSI MS-7293.....Cmq io nn voglio fare il raid, era solo per capire, come mai se imposto raid nel bios Ubuntu in fase di installazione mi vede i due hard disk, mentre se metto ide nn mi vede un bel niente????
Quando poi prima di inserire vista ubuntu mi vedeva il primo hard disk!!

Io ho ripulito al meglio il sistema dai file di Vista, anche con programmi di vista che servono per ristabilire il bootloader di Xp....poi se mi sapete dare altri consigli su kome vedere di iliminare proprio tutto mi fa piacere!!!
cmq il boot.ini sembra pulito!!

Aspetto vostre notizie

Ho provato ad impostare il secondo hard disk come volume dinamico! Ma nulla nn va!!
Cmq conviene impostare gli hard disk come base o dinamici?

Le impostazioni in Vista o Xp sono indipendenti rispetto al Sistema Ubuntu...

...quelle del BIOS invece hanno un notevole peso!

Vedi se te la senti di fare l'aggiornamento del BIOS, per vedere se risolvi.

by Ninja

Pare facile nn ho trovato nulla.....è un casino sul sito della msi!!!!
Maledetti pc preassemblati

NN trovo nulla so google sulla MSI ms-7293!!!!

Forum Ubuntu-it

Ubuntu nn mi trova nessun hard disk!!!

Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!

Re: Ubuntu nn mi trova nessun hard disk!!!