Ati Radeon 9600 con ubuntu 8.04

[trombolino]

ma guarda limitati a dare le istruzioni che ho dato io e tutto si risolve...prova e vedrai

[morfeo68]

prima o poi lo provero'

[dave83]

Avevo già provato appena aggiornato a hardy a installarli con envyng ma niente...ho provato ancora ma il risultato è lo stesso: mi peggiora la risoluzione massima del monitor e non mi funzionano cmq gli effetti grafici; e ovviamente direct rendering disattivato.
A te cosa funziona di preciso?

[trombolino]

tutto dave...ma hai provato a dare gli stessi comandi che ho dato io?

[dave83]

Sì, l'ho seguita tutta.
Solo che alla fine i risultati sono quelli...boh... ???

[trombolino]

se sono gli stessi che ho postato vanno bene dave

[Byakuya]

Dave ma ti ha dato qlc problema durante la procedura?

[dave83]

No, nessun errore!
Però sono contentissimo perchè sono appena riuscito a risolvere con i driver open!!! 
Se può servire a qualcuno ho semplicemente seguito la guida del wiki per i driver open, aggiungendo al mio xorg.conf (che avevo già modificato per aumentare le risoluzioni disponibili) le varie righe.
Questo è il mio xorg.conf attuale e mi funziona tutto.

Codice: Seleziona tutto

Section "Files"
EndSection

Section "InputDevice"
	Identifier	"Generic Keyboard"
	Driver		"kbd"
	Option		"CoreKeyboard"
	Option		"XkbRules"	"xorg"
	Option		"XkbModel"	"pc105"
	Option		"XkbLayout"	"it"
EndSection

Section "InputDevice"
	Identifier	"Configured Mouse"
	Driver		"mouse"
	Option		"CorePointer"
	Option		"Device"		"/dev/input/mice"
	Option		"Protocol"		"ImPS/2"
	Option		"ZAxisMapping"		"4 5"
EndSection

Section "InputDevice"
	Driver		"wacom"
	Identifier	"stylus"
	Option		"Device"	"/dev/input/wacom"
	Option		"Type"		"stylus"
	Option		"ForceDevice"	"ISDV4"		# Tablet PC ONLY
EndSection

Section "InputDevice"
	Driver		"wacom"
	Identifier	"eraser"
	Option		"Device"	"/dev/input/wacom"
	Option		"Type"		"eraser"
	Option		"ForceDevice"	"ISDV4"		# Tablet PC ONLY
EndSection

Section "InputDevice"
	Driver		"wacom"
	Identifier	"cursor"
	Option		"Device"	"/dev/input/wacom"
	Option		"Type"		"cursor"
	Option		"ForceDevice"	"ISDV4"		# Tablet PC ONLY
EndSection

Section "Device"
	Identifier	"ATI Technologies Inc RV350 AP [Radeon 9600]"
	Driver		"ati"
	BusID		"PCI:1:0:0"
	Option          "XAANoOffscreenPixmaps"
EndSection

Section "Monitor"
	Identifier	"Monitor Generico"
	Option		"DPMS"
	HorizSync	30-70
	VertRefresh	50-160
EndSection

Section "Screen"
	Identifier	"Default Screen"
	Device		"ATI Technologies Inc RV350 AP [Radeon 9600]"
	Monitor		"Monitor Generico"
	DefaultDepth	24
	SubSection "Display"
		Modes		"1440x900" "1400x1050" "1280x1024" "1280x960" "1280x854" "1280x800" "1280x768" "1200x800" "1152x864" "1152x768" "1024x768" "800x600" "640x480"
	EndSubSection
EndSection

Section "ServerLayout"
	Option          "AIGLX"         "true"
	Identifier	"Default Layout"
	Screen		"Default Screen"
	InputDevice	"Generic Keyboard"
	InputDevice	"Configured Mouse"

# Uncomment if you have a wacom tablet
#	InputDevice     "stylus"	"SendCoreEvents"
#	InputDevice     "cursor"	"SendCoreEvents"
#	InputDevice     "eraser"	"SendCoreEvents"
EndSection

Section "DRI"
        Mode 0666
EndSection
        
Section "Extensions"
        Option "Composite" "Enable"
EndSection

Grazie comunque a tutti per l'aiuto con i driver proprietari!  (b2b)

[Byakuya]

Ottimo!!!!!!!!!!!

[morfeo68]

No, nessun errore!
Però sono contentissimo perchè sono appena riuscito a risolvere con i driver open!!! 
Se può servire a qualcuno ho semplicemente seguito la guida del wiki per i driver open, aggiungendo al mio xorg.conf (che avevo già modificato per aumentare le risoluzioni disponibili) le varie righe.
Questo è il mio xorg.conf attuale e mi funziona tutto.

Codice: Seleziona tutto

Section "Files"
EndSection

Section "InputDevice"
	Identifier	"Generic Keyboard"
	Driver		"kbd"
	Option		"CoreKeyboard"
	Option		"XkbRules"	"xorg"
	Option		"XkbModel"	"pc105"
	Option		"XkbLayout"	"it"
EndSection

Section "InputDevice"
	Identifier	"Configured Mouse"
	Driver		"mouse"
	Option		"CorePointer"
	Option		"Device"		"/dev/input/mice"
	Option		"Protocol"		"ImPS/2"
	Option		"ZAxisMapping"		"4 5"
EndSection

Section "InputDevice"
	Driver		"wacom"
	Identifier	"stylus"
	Option		"Device"	"/dev/input/wacom"
	Option		"Type"		"stylus"
	Option		"ForceDevice"	"ISDV4"		# Tablet PC ONLY
EndSection

Section "InputDevice"
	Driver		"wacom"
	Identifier	"eraser"
	Option		"Device"	"/dev/input/wacom"
	Option		"Type"		"eraser"
	Option		"ForceDevice"	"ISDV4"		# Tablet PC ONLY
EndSection

Section "InputDevice"
	Driver		"wacom"
	Identifier	"cursor"
	Option		"Device"	"/dev/input/wacom"
	Option		"Type"		"cursor"
	Option		"ForceDevice"	"ISDV4"		# Tablet PC ONLY
EndSection

Section "Device"
	Identifier	"ATI Technologies Inc RV350 AP [Radeon 9600]"
	Driver		"ati"
	BusID		"PCI:1:0:0"
	Option          "XAANoOffscreenPixmaps"
EndSection

Section "Monitor"
	Identifier	"Monitor Generico"
	Option		"DPMS"
	HorizSync	30-70
	VertRefresh	50-160
EndSection

Section "Screen"
	Identifier	"Default Screen"
	Device		"ATI Technologies Inc RV350 AP [Radeon 9600]"
	Monitor		"Monitor Generico"
	DefaultDepth	24
	SubSection "Display"
		Modes		"1440x900" "1400x1050" "1280x1024" "1280x960" "1280x854" "1280x800" "1280x768" "1200x800" "1152x864" "1152x768" "1024x768" "800x600" "640x480"
	EndSubSection
EndSection

Section "ServerLayout"
	Option          "AIGLX"         "true"
	Identifier	"Default Layout"
	Screen		"Default Screen"
	InputDevice	"Generic Keyboard"
	InputDevice	"Configured Mouse"

# Uncomment if you have a wacom tablet
#	InputDevice     "stylus"	"SendCoreEvents"
#	InputDevice     "cursor"	"SendCoreEvents"
#	InputDevice     "eraser"	"SendCoreEvents"
EndSection

Section "DRI"
        Mode 0666
EndSection
        
Section "Extensions"
        Option "Composite" "Enable"
EndSection

Grazie comunque a tutti per l'aiuto con i driver proprietari!  (b2b)

posta per favore glxgears
e lspci -v

[dave83]

Prima di vedere che avevi postato qui ti avevo già risposto sull'altro thread...
Cmq i valori su cui mi aggiro adesso sono questi

Codice: Seleziona tutto

7713 frames in 5.0 seconds = 1542.461 FPS

Codice: Seleziona tutto

00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host Bridge (rev a1)
	Flags: bus master, 66MHz, fast devsel, latency 0
	Memory at f0000000 (32-bit, prefetchable) [size=128M]
	Capabilities: <access denied>

00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge (rev a2)
	Subsystem: Giga-byte Technology Unknown device 0c11
	Flags: bus master, 66MHz, fast devsel, latency 0

00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System Management (rev a1)
	Subsystem: Giga-byte Technology Unknown device 0c11
	Flags: 66MHz, fast devsel, IRQ 10
	I/O ports at e400 [size=32]
	I/O ports at 1c00 [size=64]
	I/O ports at 2000 [size=64]
	Capabilities: <access denied>

00:02.0 USB Controller: nVidia Corporation CK8S USB Controller (rev a1) (prog-if 10 [OHCI])
	Subsystem: Giga-byte Technology Unknown device 5004
	Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 17
	Memory at fa004000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>

00:02.1 USB Controller: nVidia Corporation CK8S USB Controller (rev a1) (prog-if 10 [OHCI])
	Subsystem: Giga-byte Technology Unknown device 5004
	Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 18
	Memory at fa005000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>

00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI])
	Subsystem: Giga-byte Technology Unknown device 5004
	Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 16
	Memory at fa000000 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>

00:05.0 Bridge: nVidia Corporation CK8S Ethernet Controller (rev a2)
	Subsystem: Giga-byte Technology Unknown device e000
	Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 16
	Memory at fa001000 (32-bit, non-prefetchable) [size=4K]
	I/O ports at b800 [size=8]
	Capabilities: <access denied>

00:06.0 Multimedia audio controller: nVidia Corporation nForce3 250Gb AC'97 Audio Controller (rev a1)
	Subsystem: Giga-byte Technology Unknown device a002
	Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 18
	I/O ports at bc00 [size=256]
	I/O ports at c000 [size=128]
	Memory at fa002000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: <access denied>

00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA Controller (v2.5) (rev a2) (prog-if 8a [Master SecP PriP])
	Subsystem: Unknown device f458:5002
	Flags: bus master, 66MHz, fast devsel, latency 0
	[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
	[virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
	[virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
	[virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
	I/O ports at f000 [size=16]
	Capabilities: <access denied>

00:0a.0 IDE interface: nVidia Corporation CK8S Serial ATA Controller (v2.5) (rev a2) (prog-if 85 [Master SecO PriO])
	Subsystem: Giga-byte Technology Unknown device b002
	Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 17
	I/O ports at 09f0 [size=8]
	I/O ports at 0bf0 [size=4]
	I/O ports at 0970 [size=8]
	I/O ports at 0b70 [size=4]
	I/O ports at dc00 [size=16]
	I/O ports at e000 [size=128]
	Capabilities: <access denied>

00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to PCI Bridge (rev a2) (prog-if 00 [Normal decode])
	Flags: bus master, 66MHz, medium devsel, latency 16
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=10
	I/O behind bridge: 0000a000-0000afff
	Memory behind bridge: f8000000-f9ffffff
	Prefetchable memory behind bridge: d0000000-efffffff

00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI Bridge (rev a2) (prog-if 00 [Normal decode])
	Flags: bus master, 66MHz, fast devsel, latency 0
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=128

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
	Flags: fast devsel
	Capabilities: <access denied>

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
	Flags: fast devsel

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
	Flags: fast devsel

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
	Flags: fast devsel

01:00.0 VGA compatible controller: ATI Technologies Inc RV350 AP [Radeon 9600] (prog-if 00 [VGA controller])
	Subsystem: PC Partner Limited Unknown device 7c20
	Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 19
	Memory at d0000000 (32-bit, prefetchable) [size=256M]
	I/O ports at a000 [size=256]
	Memory at f9000000 (32-bit, non-prefetchable) [size=64K]
	[virtual] Expansion ROM at f8000000 [disabled] [size=128K]
	Capabilities: <access denied>

01:00.1 Display controller: ATI Technologies Inc RV350 AP [Radeon 9600] (Secondary)
	Subsystem: PC Partner Limited Unknown device 7c21
	Flags: bus master, 66MHz, medium devsel, latency 32
	Memory at e0000000 (32-bit, prefetchable) [size=256M]
	Memory at f9010000 (32-bit, non-prefetchable) [size=64K]
	Capabilities: <access denied>

[morfeo68]

ho provato il tuo xorg ma non mi funziona

[morfeo68]

come faccio a conoscere i parametri del mio monitor?

[dave83]

Con la 7.10 potevi farli rilevare in automatico riconfigurando xorg (nella sezione video); non so come si possa fare con la 8.04, però credo potresti farcela con un cd live della 7.10 e dando

Codice: Seleziona tutto

sudo dpkg-reconfigure xserver-xorg

Fai tutta la procedura guidata, impostando anche le risoluzioni video massime che vuoi e magari aggiungendo già le righe per abilitare il direct rendering, ecc... (come da wiki: http://wiki.ubuntu-it.org/Hardware/Video/Ati/RadeonDriver; poi copi lo xorg.conf risultante da qualche parte. Poi puoi sostituirlo a quello della 8.04 e vedere cosa succede...

Mi raccomando, poi riavvia il computer; io le prime volte dopo aver cambiato xorg.conf (mettendolo praticamente com'è adesso) non ottenevo risultati credo perchè riavviavo solo gnome (CTRL+ALT+BACKSPACE).

[Byakuya]

attenzione fatevi sempre una copia di backup...non è così immediato e senza dolore cambiare lo Xorg!!!!

[melixari]

ciao a tutti
io ho una  9200...
ho fatto tutti i passaggi fino ad arrivare qui

      +-----------------------------------------------------------+
      |    EnvyNG Menu ver.1.1.1                                  |
      |                                                          |
      |    1 - Install the NVIDIA driver                          |
      |                                                          |
      |    2 - Uninstall the NVIDIA driver                        |
      |                                                          |
      |    3 - Install the ATI driver                            |
      |                                                          |
      |    4 - Uninstall the ATI driver                          |
      |                                                          |
      |    5 - Install the ATI/NVIDIA driver Manually            |
      |                                                          |
      |    6 - Restart the Xserver                                |
      |                                                          |
      |    7 - Restart your computer                              |
      |                                                          |
      |    8 - Exit                                              |
      |                                                          |
      |    NOTE: IF THE SCREEN TURNS BLACK, PLEASE TYPE ALT+F1    |
      +-----------------------------------------------------------+
Please select one of the activities displayed above and press ENTER:

3
EnvyNG - Version 1.1.1

Ubuntu Hardy 32bit
Your graphic card has been detected as a ATI Radeon 9250/9200 Series
Your graphic card is supported by the legacy Driver
EnvyNG ERROR: ATI's legacy driver does not support your operating system
...

e poi??
aiuto