Come da oggetto, lo scanner in questione pilotato da scheda SCSI Advansys funzionava perfettamente con il programma Vuescan 8.4.68 sotto Ubuntu 7.10 abbandonando definitivamente WinXP.
Dopo l'aggiornamento alla versione Ubuntu 8.04 amaramente il tutto non funziona, ossia non viene rilevato lo scanner, ho reinstallato dal DVD sempre la versione 8.04 di Ubuntu ma con lo stesso risultato. Leggendo altri topic in merito ho eseguito da terminale il comando: scsiinfo -a /dev/sg0 ottenendo il seguente listato:
----------------------------------------------------------
adriano@AD-Ubuntu:~$ sudo scsiinfo -a /dev/sg0
[sudo] password for adriano:
Scsiinfo version 1.7(eowmob)
Inquiry command
---------------
Relative Address 0
Wide bus 32 0
Wide bus 16 0
Synchronous neg. 0
Linked Commands 0
Command Queueing 0
SftRe 0
Device Type 6
Peripheral Qualifier 0
Removable? 0
Device Type Modifier 54
ISO Version 0
ECMA Version 2
ANSI Version 7
AENC 0
TrmIOP 0
Response Data Format 1
Vendor: AGFA
Product: DUOSCAN
Revision level: 1.70SCSI FW V3.6 CTL5380#O��#�]C##G
Serial Number '['
Data from Rigid Disk Drive Geometry Page
----------------------------------------
Number of cylinders 8390407
Number of heads 0
Starting write precomp 16744455
Starting reduced current 459007
Drive step rate 32768
Landing Zone Cylinder 0
RPL 0
Rotational Offset 0
Rotational Rate 0
Data from Caching Page
----------------------
Write Cache 0
Read Cache 1
Prefetch units 0
Demand Read Retention Priority 0
Demand Write Retention Priority 7
Disable Pre-fetch Transfer Length 1792
Minimum Pre-fetch 65408
Maximum Pre-fetch 1799
Maximum Pre-fetch Ceiling 255
Data from Format Device Page
----------------------------
Removable Medium 0
Supports Hard Sectoring 0
Supports Soft Sectoring 0
Addresses assigned by surface 0
Tracks per Zone 32775
Alternate sectors per zone 1792
Alternate tracks per zone 65408
Alternate tracks per lun 1799
Sectors per track 255
Bytes per sector 32768
Interleave 0
Track skew factor 0
Cylinder skew factor 0
Data from Error Recovery Page
-----------------------------
AWRE 1
ARRE 0
TB 0
RC 0
EER 0
PER 0
DTE 0
DCR 0
Read Retry Count 7
Correction Span 7
Head Offset Count 0
Data Strobe Offset Count 255
Write Retry Count 7
Recovery Time Limit 255
Data from Control Page
----------------------
RLEC 0
QErr 1
DQue 1
EECA 0
RAENP 1
UUAENP 1
EAENP 1
Queue Algorithm Modifier 0
Ready AEN Holdoff Period 65408
Data from Disconnect-Reconnect Page
-----------------------------------
Buffer full ratio 128
Buffer empty ratio 7
Bus Inactivity Limit 1792
Disconnect Time Limit 65408
Connect Time Limit 1799
Maximum Burst Size 255
DTDC 0x80
Data from Defect Lists
----------------------
Unable to read manufacturer defect data.
Unable to read grown defect data.
Data from Notch Parameters Page
-------------------------------
Notched Drive 1
Logical or Physical Notch 0
Max # of notches 1792
Active Notch 65408
Starting Boundary 0x70700ff
Ending Boundary 0x80000000
Pages Notched 00000000 00000000
Data from Verify Error Recovery Page
------------------------------------
EER 0
PER 0
DTE 0
DCR 0
Verify Retry Count 7
Verify Correction Span (bits) 7
Verify Recovery Time Limit (ms) 255
Data from Peripheral Device Page
--------------------------------
Interface Identifier 0x8007
Vendor Specific
Vendor Specific Data 0x070700ff8000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000
----------------------
come si nota la periferisca Agfa Duoscan viene rilevata ma non esercibile dal programma. Con Xsane non sono riuscito neanche con la 7.10 a farlo pilotare. Si chiede gentilmente come ovviare al problema, altrimenti tocca ritornare alla 7.10.
Essendo un profano vi prego di essere molto comprensivi, Grazie.
[Risolto] [Driver] Scanner SCSI Agfa Duoscan
[Risolto] [Driver] Scanner SCSI Agfa Duoscan
Ultima modifica di adcalian il giovedì 12 maggio 2011, 22:58, modificato 1 volta in totale.
Re: [Driver] Scanner SCSI Agfa Duoscan
sei sicuro di avere sane e xsane installati?... lo dico perche' io ho installato kubuntu 8.04 e di default non vengono installati.
Poi, una volta installati, proverei a fare un sane-find-scanner e vedere che dice... da quel che scrivi mi pare che il problema sia solo quello di configurare correttamente sane.
Poi, una volta installati, proverei a fare un sane-find-scanner e vedere che dice... da quel che scrivi mi pare che il problema sia solo quello di configurare correttamente sane.
Re: [Driver] Scanner SCSI Agfa Duoscan
Forse mi sono spiegato male. Lo scanner in questione con la 7.10 di ubuntu funzionava solo con il programma Vuescan, mentre con Xsane non veniva riconosciuto, succesivamente all'aggiornamento della 8.04 il tutto non funzionava +. Comunque ho installato come da te consigliato Xsane con Sane con esito negativo, la periferica non viene rilevata, questo nonostante la scheda SCSI pilota anche un masterizzatore che viene normalmente visualizzato e usato.
Non sò + che pesci pigliare.
Questo è quello che mi esce al comando da terminale da te proposto:
adriano@AD-Ubuntu:~$ sane-find-scanner
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
# No USB scanners found. If you expected something different, make sure that
# you have loaded a kernel driver for your USB host controller and have setup
# the USB system correctly. See man sane-usb for details.
# Not checking for parallel port scanners.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.
# You may want to run this program as root to find all devices. Once you
# found the scanner devices, be sure to adjust access permissions as
# necessary.
adriano@AD-Ubuntu:~$
Non sò + che pesci pigliare.
Questo è quello che mi esce al comando da terminale da te proposto:
adriano@AD-Ubuntu:~$ sane-find-scanner
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
# No USB scanners found. If you expected something different, make sure that
# you have loaded a kernel driver for your USB host controller and have setup
# the USB system correctly. See man sane-usb for details.
# Not checking for parallel port scanners.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.
# You may want to run this program as root to find all devices. Once you
# found the scanner devices, be sure to adjust access permissions as
# necessary.
adriano@AD-Ubuntu:~$
Re: [Driver] Scanner SCSI Agfa Duoscan
potrebbe essere un problema di permessi
mi pare che sane-find-scanner l'hai lanciato da utente e non da root; prova a lanciarlo da root, se ti vede lo scanner vuol dire che hai qualche problema di permessi sui device
mi pare che sane-find-scanner l'hai lanciato da utente e non da root; prova a lanciarlo da root, se ti vede lo scanner vuol dire che hai qualche problema di permessi sui device
[Risolto] [Driver] Re: [Driver] Scanner SCSI Agfa Duoscan
Finalmente e definitivamente risolto.
Ho acquistato il software VUESCAN v8 a circa 80$ che gira benissimo su ubuntu 10.04 ed ho finalmente eliminato la partizione dedicata a windowXP.
Essendo uno scanner datato (pagato oltre 8 milioni delle vecchie lire) ma ancora valido per la qualità del sensore e del gruppo ottico non avevo assolutamente voglia di buttarlo.
Ho acquistato il software VUESCAN v8 a circa 80$ che gira benissimo su ubuntu 10.04 ed ho finalmente eliminato la partizione dedicata a windowXP.
Essendo uno scanner datato (pagato oltre 8 milioni delle vecchie lire) ma ancora valido per la qualità del sensore e del gruppo ottico non avevo assolutamente voglia di buttarlo.
Ultima modifica di adcalian il giovedì 9 settembre 2010, 20:07, modificato 1 volta in totale.
Chi c’è in linea
Visualizzano questa sezione: Google [Bot], nick091 e 5 ospiti