[Wireless] broadcam b43

[[lost]-Divilinux]

c'è il modo di far andare i b43 su gusty?

si compilando i compat-wireless

[mbiza]

li ho compilati, seguendo questa guida sul wiki ma non funziona. Domattina provo a rifare tutto da capo.

Codice: Seleziona tutto

SIOCSIFFLAGS: Operazione non supportata

ma questo errore cosa significa?

[[lost]-Divilinux]

in un qualche contesto si potrebbe dire di piu'..cosi' sembra che non ci sia nessuna interfaccia abilitata..puo' voler dire molte cose, in primis che non ci sono i driver

[mbiza]

dannazione(..) ho riprovato da capo a ricompilare i compat-wireless ma non funzionano, la scheda non è più riconosciuta...
quell'errore viene fuori se faccio

Codice: Seleziona tutto

sudo ifconfig eth1 up

c'è qualcosa che non va.....

[[lost]-Divilinux]

prima devi caricare i driver

Codice: Seleziona tutto

sudo modprobe b43

pi dopo al limite vedi se esce l'interfaccia..io non ho mica visto la compilazione. Tu sei sicuro di averli installati questi driver?..e il firmware dei b43 lo hai messo in /lib/firmware?

[andrjs]

Senti, anch'io ho i b43 e mi era stato detto che erano nel kernel e quant'altro, ma poi spulciando nel web l'unica soluzione ottimale, anche in termini di prestazioni, che ho trovato è quello della guida per ndiswrapper (va bene anche per gusty, devi solo saltare il passaggio degli ssb e mettere in blacklist bmc43xx), anche perchè in meno di 10 minuti funziona tutto e alla perfezione.

Ciao

[[lost]-Divilinux]

e mi era stato detto che erano nel kernel e quant'altro

infatti sono li, ma in alcuni casi si tratta di una versione incompatibile con certe schede..per questo bisogna tentare con i b43 piu' recenti che, appunto, si trovano nei compat wireless

[andrjs]

infatti sono li, ma in alcuni casi si tratta di una versione incompatibile con certe schede..per questo bisogna tentare con i b43 piu' recenti che, appunto, si trovano nei compat wireless

Probabilmente hai ragione tu, ma ti assicuro che sulla 7.10 anche con i compat wireless non ero riuscito e quando ho reinstallato la 8.04 ho rifatto la configurazione con ndiswrapper che sapevo funzionante.

[mbiza]

il firmware sembra che c'è

Codice: Seleziona tutto

renato@mbiza-laptop:~$ cd /lib/firmware/
renato@mbiza-laptop:/lib/firmware$ ls -al
totale 36
drwxr-xr-x  4 root root  4096 2008-06-16 22:04 .
drwxr-xr-x 17 root root 12288 2008-05-28 02:18 ..
drwxr-xr-x  4 root root 12288 2007-12-27 02:24 2.6.22-14-generic
drwxr-x---  2 root root  4096 2008-06-16 22:04 b43
-rw-r--r--  1 root root    52 2007-12-23 19:46 bcm43xx_microcode11.fw

i driver venivano caricati con uno script (make load) durante l'installazione, e ho visto che nello script c'è il comando modprobe che carica il modulo, poi l'ho anche rifatto ma su ifconfig la scheda wireless non appare nemmeno...

Eppure ho controllato e la mia scheda è supportata da quei driver...

[[lost]-Divilinux]

@mbiza
puoi postare il dmesg dopo aver caricato in manuale i b43? ho bisogno sia di quello..che del caricamento in manuale

Codice: Seleziona tutto

sudo modprobe b43

aspetto fino a quando non posti entrambi altrimenti come faccio io da qua a capire dove sta il problema? (sfere di cristallo a parte)

Nella directory /lib/firmware c'e' un "b43"..siamo sicuri che sia il firmware?..perche' a me sembra un folder..e probabilmente li dentro c'e' il firmware...il firmware deve stare in /lib/firmware e non in /lib/firmware/b43

[mbiza]

è una cartella, hai ragione, dovrei spostare i file nella cartella /b43 in /firmware?

Codice: Seleziona tutto

root@mbiza-laptop:/lib/firmware# cd b43/
root@mbiza-laptop:/lib/firmware/b43# ls -al
totale 176
drwxr-x--- 2 root root  4096 2008-06-16 22:04 .
drwxr-xr-x 4 root root  4096 2008-06-16 22:04 ..
-rw-r--r-- 1 root root    18 2008-06-17 15:48 a0g0bsinitvals4.fw
-rw-r--r-- 1 root root   158 2008-06-17 15:48 a0g0bsinitvals5.fw
-rw-r--r-- 1 root root  2680 2008-06-17 15:48 a0g0initvals4.fw
-rw-r--r-- 1 root root  1858 2008-06-17 15:48 a0g0initvals5.fw
-rw-r--r-- 1 root root   158 2008-06-17 15:48 a0g1bsinitvals13.fw
-rw-r--r-- 1 root root   158 2008-06-17 15:48 a0g1bsinitvals5.fw
-rw-r--r-- 1 root root  2056 2008-06-17 15:48 a0g1initvals13.fw
-rw-r--r-- 1 root root  1858 2008-06-17 15:48 a0g1initvals5.fw
-rw-r--r-- 1 root root   158 2008-06-17 15:48 b0g0bsinitvals13.fw
-rw-r--r-- 1 root root    18 2008-06-17 15:48 b0g0bsinitvals4.fw
-rw-r--r-- 1 root root   158 2008-06-17 15:48 b0g0bsinitvals5.fw
-rw-r--r-- 1 root root  2056 2008-06-17 15:48 b0g0initvals13.fw
-rw-r--r-- 1 root root  2680 2008-06-17 15:48 b0g0initvals4.fw
-rw-r--r-- 1 root root  1858 2008-06-17 15:48 b0g0initvals5.fw
-rw-r--r-- 1 root root   158 2008-06-17 15:48 lp0bsinitvals13.fw
-rw-r--r-- 1 root root  2052 2008-06-17 15:48 lp0initvals13.fw
-rw-r--r-- 1 root root  1320 2008-06-17 15:48 pcm4.fw
-rw-r--r-- 1 root root  1320 2008-06-17 15:48 pcm5.fw
-rw-r--r-- 1 root root 26600 2008-06-17 15:48 ucode11.fw
-rw-r--r-- 1 root root 24424 2008-06-17 15:48 ucode13.fw
-rw-r--r-- 1 root root 20080 2008-06-17 15:48 ucode4.fw
-rw-r--r-- 1 root root 22088 2008-06-17 15:48 ucode5.fw

dopo modprobe b43 il dmesg sembra non dica niente  :-\

Codice: Seleziona tutto

renato@mbiza-laptop:~$ sudo modprobe b43
ultime righe...
[67614.452000] sd 7:0:0:0: [sdb] 7954431 512-byte hardware sectors (4073 MB)
[67614.452000] sd 7:0:0:0: [sdb] Write Protect is off
[67614.452000] sd 7:0:0:0: [sdb] Mode Sense: 45 00 00 08
[67614.452000] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[67614.456000] sd 7:0:0:0: [sdb] 7954431 512-byte hardware sectors (4073 MB)
[67614.456000] sd 7:0:0:0: [sdb] Write Protect is off
[67614.456000] sd 7:0:0:0: [sdb] Mode Sense: 45 00 00 08
[67614.456000] sd 7:0:0:0: [sdb] Assuming drive cache: write through
[67614.456000]  sdb: sdb1
[67614.456000] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[67614.456000] sd 7:0:0:0: Attached scsi generic sg2 type 0
renato@mbiza-laptop:~$ 

[[lost]-Divilinux]

è una cartella, hai ragione, dovrei spostare i file nella cartella /b43 in /firmware?

si esatto..ma ora questa interfaccia c'e'?..bisogna essere un po' veloci, scusa se te lo dico..i comandi sono sempre quelli..dmesg per l'output, modprobe per caricare il modulo, iwconfig per vedere se c'e' l'interfaccia..altrimenti questo topic finisce per diventare un romanzo..

[mbiza]

ce li avevo già copiati anche prima di ricaricare il modulo, poi su ifconfig non è mai apparsa eth1...
In /firmware c'e ancora bcm43xx_microcode11.fw, devo forse eliminarlo?
ecco anche ifconfig ma non credo serva a molto

Codice: Seleziona tutto

root@mbiza-laptop:# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:17:A4:D1:68:0B  
          inet addr:192.168.1.3  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::217:a4ff:fed1:680b/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1653904 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1643488 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:1297992272 (1.2 GB)  TX bytes:973599718 (928.4 MB)
          Interrupt:16 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:47 errors:0 dropped:0 overruns:0 frame:0
          TX packets:47 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:7431 (7.2 KB)  TX bytes:7431 (7.2 KB)

scusa per il romanzo, non so se sbaglio qualcosa >:(

[[lost]-Divilinux]

manca il dmesg TOTALE poi forse abbiamo il quadro completo della situazione..dell'interfaccia neanche l'ombra.

[mbiza]

riepilogo:

Codice: Seleziona tutto

renato@mbiza-laptop:~$ ifconfig
eth0      Link encap:Ethernet  HWaddr 00:17:A4:D1:68:0B  
          inet addr:192.168.1.3  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::217:a4ff:fed1:680b/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:29 errors:0 dropped:0 overruns:0 frame:0
          TX packets:67 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:3180 (3.1 KB)  TX bytes:8932 (8.7 KB)
          Interrupt:16 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:12 errors:0 dropped:0 overruns:0 frame:0
          TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:600 (600.0 b)  TX bytes:600 (600.0 b)

Codice: Seleziona tutto

renato@mbiza-laptop:~$ sudo modprobe b43
[sudo] password for renato:
renato@mbiza-laptop:~$

dmsg

Codice: Seleziona tutto

[   25.066414] Security Framework v1.0.0 initialized
[   25.066421] SELinux:  Disabled at boot.
[   25.066435] Mount-cache hash table entries: 512
[   25.066548] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
[   25.066556] monitor/mwait feature present.
[   25.066558] using mwait in idle threads.
[   25.066562] CPU: L1 I cache: 32K, L1 D cache: 32K
[   25.066565] CPU: L2 cache: 2048K
[   25.066568] CPU: Physical Processor ID: 0
[   25.066570] CPU: Processor Core ID: 0
[   25.066571] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c1a9 00000000 00000000
[   25.066580] Compat vDSO mapped to ffffe000.
[   25.066591] Checking 'hlt' instruction... OK.
[   25.082472] SMP alternatives: switching to UP code
[   25.082879] Early unpacking initramfs... done
[   25.428144] ACPI: Core revision 20070126
[   25.428272] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[   25.504197] CPU0: Intel Genuine Intel(R) CPU           T2300  @ 1.66GHz stepping 08
[   25.504214] SMP alternatives: switching to SMP code
[   25.504324] Booting processor 1/1 eip 3000
[   25.514530] Initializing CPU#1
[   25.593580] Calibrating delay using timer specific routine.. 3325.04 BogoMIPS (lpj=6650091)
[   25.593587] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000
[   25.593592] monitor/mwait feature present.
[   25.593595] CPU: L1 I cache: 32K, L1 D cache: 32K
[   25.593598] CPU: L2 cache: 2048K
[   25.593600] CPU: Physical Processor ID: 0
[   25.593602] CPU: Processor Core ID: 1
[   25.593603] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c1a9 00000000 00000000
[   25.594180] CPU1: Intel Genuine Intel(R) CPU           T2300  @ 1.66GHz stepping 08
[   25.594206] Total of 2 processors activated (6653.76 BogoMIPS).
[   25.594401] ENABLING IO-APIC IRQs
[   25.594609] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[   25.741449] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[   25.761436] Brought up 2 CPUs
[   25.858784] migration_cost=44
[   25.858931] HP Compaq Laptop series board detected. Selecting BIOS-method for reboots.
[   25.858934] Booting paravirtualized kernel on bare hardware
[   25.859024] Time: 18:27:18  Date: 05/17/108
[   25.859046] NET: Registered protocol family 16
[   25.859137] EISA bus registered
[   25.859142] ACPI: bus type pci registered
[   25.860462] PCI: PCI BIOS revision 2.10 entry at 0xf0322, last bus=8
[   25.860464] PCI: Using configuration type 1
[   25.860466] Setting up standard PCI resources
[   25.862510] ACPI: EC: Look up EC in DSDT
[   25.863221] ACPI: EC: GPE=0x16, ports=0x66, 0x62
[   25.892264] ACPI: Interpreter enabled
[   25.892268] ACPI: (supports S0 S3 S4 S5)
[   25.892283] ACPI: Using IOAPIC for interrupt routing
[   25.902966] ACPI: EC: GPE=0x16, ports=0x66, 0x62
[   25.903044] ACPI: PCI Root Bridge [C002] (0000:00)
[   25.903057] PCI: Probing PCI hardware (bus 00)
[   25.903732] PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO
[   25.903737] PCI quirk: region 1100-113f claimed by ICH6 GPIO
[   25.904496] PCI: Transparent bridge - 0000:00:1e.0
[   25.904603] ACPI: PCI Interrupt Routing Table [\_SB_.C002._PRT]
[   25.904944] ACPI: PCI Interrupt Routing Table [\_SB_.C002.C096._PRT]
[   25.905120] ACPI: PCI Interrupt Routing Table [\_SB_.C002.C102._PRT]
[   25.941216] ACPI: PCI Interrupt Link [C10E] (IRQs 10 *11)
[   25.941455] ACPI: PCI Interrupt Link [C10F] (IRQs *10 11)
[   25.941692] ACPI: PCI Interrupt Link [C110] (IRQs *10 11)
[   25.941928] ACPI: PCI Interrupt Link [C111] (IRQs *10 11)
[   25.942166] ACPI: PCI Interrupt Link [C12A] (IRQs *10 11)
[   25.942402] ACPI: PCI Interrupt Link [C12B] (IRQs 10 *11)
[   25.942631] ACPI: PCI Interrupt Link [C12C] (IRQs 10 11) *0, disabled.
[   25.942745] ACPI Exception (pci_link-0179): AE_NOT_FOUND, Evaluating _PRS [20070126]
[   25.942965] ACPI: Power Resource [C21A] (on)
[   25.943027] ACPI: Power Resource [C222] (off)
[   25.943154] ACPI: Power Resource [C321] (off)
[   25.943267] ACPI: Power Resource [C322] (off)
[   25.943380] ACPI: Power Resource [C323] (off)
[   25.943492] ACPI: Power Resource [C324] (off)
[   25.943506] Linux Plug and Play Support v0.97 (c) Adam Belay
[   25.943516] pnp: PnP ACPI init
[   25.943524] ACPI: bus type pnp registered
[   25.951809] pnp: PnP ACPI: found 12 devices
[   25.951811] ACPI: ACPI bus type pnp unregistered
[   25.951815] PnPBIOS: Disabled by ACPI PNP
[   25.951861] PCI: Using ACPI for IRQ routing
[   25.951864] PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
[   26.019497] NET: Registered protocol family 8
[   26.019500] NET: Registered protocol family 20
[   26.019551] pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
[   26.019555] pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved
[   26.019558] pnp: 00:00: iomem range 0x100000-0x1f7fffff could not be reserved
[   26.019568] pnp: 00:09: iomem range 0xffb00000-0xffbfffff could not be reserved
[   26.019572] pnp: 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
[   26.019577] pnp: 00:0a: ioport range 0x4d0-0x4d1 has been reserved
[   26.019580] pnp: 00:0a: ioport range 0x1000-0x107f has been reserved
[   26.019583] pnp: 00:0a: ioport range 0x1100-0x113f has been reserved
[   26.019586] pnp: 00:0a: ioport range 0x1200-0x121f has been reserved
[   26.019590] pnp: 00:0a: iomem range 0xf8000000-0xfbffffff has been reserved
[   26.019593] pnp: 00:0a: iomem range 0xfec00000-0xfec000ff could not be reserved
[   26.019597] pnp: 00:0a: iomem range 0xfed20000-0xfed3ffff could not be reserved
[   26.019600] pnp: 00:0a: iomem range 0xfed45000-0xfed8ffff could not be reserved
[   26.019605] pnp: 00:0b: iomem range 0xfeda0000-0xfedbffff could not be reserved
[   26.019609] pnp: 00:0b: iomem range 0xfee00000-0xfee00fff could not be reserved
[   26.020932] Time: tsc clocksource has been installed.
[   26.020947] Switched to high resolution mode on CPU 0
[   26.021034] Switched to high resolution mode on CPU 1
[   26.049895] PCI: Bridge: 0000:00:1c.0
[   26.049897]   IO window: disabled.
[   26.049904]   MEM window: e8000000-e80fffff
[   26.049908]   PREFETCH window: disabled.
[   26.049917] PCI: Bus 3, cardbus bridge: 0000:02:06.0
[   26.049919]   IO window: 00002000-000020ff
[   26.049925]   IO window: 00002400-000024ff
[   26.049930]   PREFETCH window: 20000000-23ffffff
[   26.049935]   MEM window: 24000000-27ffffff
[   26.049940] PCI: Bridge: 0000:00:1e.0
[   26.049944]   IO window: 2000-2fff
[   26.049950]   MEM window: e8100000-e83fffff
[   26.049955]   PREFETCH window: 20000000-23ffffff
[   26.049984] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[   26.049991] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   26.050006] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[   26.050024] ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 18 (level, low) -> IRQ 17
[   26.050041] NET: Registered protocol family 2
[   26.096799] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[   26.096831] TCP established hash table entries: 16384 (order: 5, 196608 bytes)
[   26.096968] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[   26.097063] TCP: Hash tables configured (established 16384 bind 16384)
[   26.097066] TCP reno registered
[   26.112864] checking if image is initramfs... it is
[   26.800538] Freeing initrd memory: 7048k freed
[   26.801154] audit: initializing netlink socket (disabled)
[   26.801172] audit(1213727238.344:1): initialized
[   26.803256] VFS: Disk quotas dquot_6.5.1
[   26.803311] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   26.803406] io scheduler noop registered
[   26.803408] io scheduler anticipatory registered
[   26.803411] io scheduler deadline registered
[   26.803427] io scheduler cfq registered (default)
[   26.803443] Boot video device is 0000:00:02.0
[   26.803613] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[   26.803671] assign_interrupt_mode Found MSI capability
[   26.803674] Allocate Port Service[0000:00:1c.0:pcie00]
[   26.803711] Allocate Port Service[0000:00:1c.0:pcie02]
[   26.803885] isapnp: Scanning for PnP cards...
[   27.157185] isapnp: No Plug & Play device found
[   27.179978] Real Time Clock Driver v1.12ac
[   27.180250] hpet_resources: 0xfed00000 is busy
[   27.180321] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[   27.181465] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[   27.181693] input: Macintosh mouse button emulation as /class/input/input0
[   27.181774] PNP: PS/2 Controller [PNP0303:C217,PNP0f13:C218] at 0x60,0x64 irq 1,12
[   27.183912] i8042.c: Detected active multiplexing controller, rev 1.1.
[   27.184660] serio: i8042 KBD port at 0x60,0x64 irq 1
[   27.184665] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[   27.184667] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[   27.184670] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[   27.184673] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[   27.184847] mice: PS/2 mouse device common for all mice
[   27.185048] EISA: Probing bus 0 at eisa.0
[   27.185056] Cannot allocate resource for EISA slot 1
[   27.185059] Cannot allocate resource for EISA slot 2
[   27.185074] Cannot allocate resource for EISA slot 6
[   27.185085] EISA: Detected 0 cards.
[   27.185175] TCP cubic registered
[   27.185190] NET: Registered protocol family 1
[   27.185214] Using IPI No-Shortcut mode
[   27.185371]   Magic number: 12:113:494
[   27.185696] Freeing unused kernel memory: 364k freed
[   27.212331] input: AT Translated Set 2 keyboard as /class/input/input1
[   28.383316] AppArmor: AppArmor initialized<5>audit(1213727239.844:2):  type=1505 info="AppArmor initialized" pid=1254
[   28.388857] fuse init (API version 7.8)
[   28.392943] Failure registering capabilities with primary security module.
[   28.425784] ACPI: Transitioning device [C325] to D3
[   28.425787] ACPI: Transitioning device [C325] to D3
[   28.425790] ACPI: Fan [C325] (off)
[   28.426009] ACPI: Transitioning device [C326] to D3
[   28.426011] ACPI: Transitioning device [C326] to D3
[   28.426014] ACPI: Fan [C326] (off)
[   28.426231] ACPI: Transitioning device [C327] to D3
[   28.426233] ACPI: Transitioning device [C327] to D3
[   28.426236] ACPI: Fan [C327] (off)
[   28.426452] ACPI: Transitioning device [C328] to D3
[   28.426454] ACPI: Transitioning device [C328] to D3
[   28.426457] ACPI: Fan [C328] (off)
[   28.431759] ACPI: SSDT 1F7F5A8C, 01FB (r1 HP      Cpu0Ist     3000 INTL 20050624)
[   28.432012] ACPI: SSDT 1F7F5D0C, 04CB (r1 HP      Cpu0Cst     3001 INTL 20050624)
[   28.436632] ACPI: CPU0 (power states: C1[C1] C2[C2])
[   28.436637] ACPI: Processor [CPU0] (supports 8 throttling states)
[   28.436857] ACPI: SSDT 1F7F59C4, 00C8 (r1 HP      Cpu1Ist     3000 INTL 20050624)
[   28.437090] ACPI: SSDT 1F7F5C87, 0085 (r1 HP      Cpu1Cst     3000 INTL 20050624)
[   28.437673] ACPI: CPU1 (power states: C1[C1] C2[C2])
[   28.437678] ACPI: Processor [CPU1] (supports 8 throttling states)
[   28.460220] ACPI: Thermal Zone [TZ0] (42 C)
[    3.288000] Marking TSC unstable due to: possible TSC halt in C2.
[    3.292000] Time: hpet clocksource has been installed.
[    3.300000] ACPI: Thermal Zone [TZ1] (40 C)
[    3.316000] ACPI: Thermal Zone [TZ2] (40 C)
[    3.324000] ACPI: Thermal Zone [TZ3] (30 C)
[    3.328000] ACPI: Thermal Zone [TZ4] (66 C)
[    3.704000] usbcore: registered new interface driver usbfs
[    3.704000] usbcore: registered new interface driver hub
[    3.704000] usbcore: registered new device driver usb
[    3.704000] USB Universal Host Controller Interface driver v3.0
[    3.704000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 18
[    3.704000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[    3.708000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    3.708000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    3.708000] uhci_hcd 0000:00:1d.0: irq 18, io base 0x00006020
[    3.708000] usb usb1: configuration #1 chosen from 1 choice
[    3.708000] hub 1-0:1.0: USB hub found
[    3.708000] hub 1-0:1.0: 2 ports detected
[    3.804000] SCSI subsystem initialized
[    3.812000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 21 (level, low) -> IRQ 19
[    3.812000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[    3.812000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    3.812000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[    3.812000] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00006040
[    3.812000] usb usb2: configuration #1 chosen from 1 choice
[    3.812000] hub 2-0:1.0: USB hub found
[    3.812000] hub 2-0:1.0: 2 ports detected
[    3.816000] libata version 2.21 loaded.
[    3.920000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 17
[    3.920000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[    3.920000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    3.920000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[    3.920000] uhci_hcd 0000:00:1d.2: irq 17, io base 0x00006060
[    3.920000] usb usb3: configuration #1 chosen from 1 choice
[    3.920000] hub 3-0:1.0: USB hub found
[    3.920000] hub 3-0:1.0: 2 ports detected
[    4.024000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 20
[    4.024000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[    4.024000] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    4.024000] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[    4.024000] uhci_hcd 0000:00:1d.3: irq 20, io base 0x00006080
[    4.024000] usb usb4: configuration #1 chosen from 1 choice
[    4.024000] hub 4-0:1.0: USB hub found
[    4.024000] hub 4-0:1.0: 2 ports detected
[    4.132000] b44.c:v1.01 (Jun 16, 2006)
[    4.132000] ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 16 (level, low) -> IRQ 16
[    4.132000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 18
[    4.136000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[    4.136000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    4.136000] eth0: Broadcom 4400 10/100BaseT Ethernet 00:17:a4:d1:68:0b
[    4.136000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[    4.136000] ehci_hcd 0000:00:1d.7: debug port 1
[    4.136000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[    4.136000] ehci_hcd 0000:00:1d.7: irq 18, io mem 0xe8584000
[    4.216000] usb 2-1: new full speed USB device using uhci_hcd and address 2
[    4.216000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    4.216000] usb usb5: configuration #1 chosen from 1 choice
[    4.216000] hub 5-0:1.0: USB hub found
[    4.216000] hub 5-0:1.0: 8 ports detected
[    4.320000] ACPI: PCI Interrupt 0000:02:06.1[B] -> GSI 19 (level, low) -> IRQ 20
[    4.368000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20]  MMIO=[e8101000-e81017ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[    4.368000] ahci 0000:00:1f.2: version 2.2
[    4.368000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 21
[    4.664000] usb 5-3: new high speed USB device using ehci_hcd and address 2
[    4.796000] usb 5-3: configuration #1 chosen from 1 choice
[    4.980000] usbcore: registered new interface driver libusual
[    4.984000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[    4.984000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[    4.988000] Initializing USB Mass Storage driver...
[    5.224000] usb 2-2: new low speed USB device using uhci_hcd and address 3
[    5.372000] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0xf impl SATA mode
[    5.372000] ahci 0000:00:1f.2: flags: 64bit ncq ilck stag pm led clo pmp pio slum part 
[    5.372000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[    5.372000] scsi0 : ahci
[    5.372000] scsi1 : ahci
[    5.372000] scsi2 : ahci
[    5.372000] scsi3 : ahci
[    5.372000] ata1: SATA max UDMA/133 cmd 0xe0076100 ctl 0x00000000 bmdma 0x00000000 irq 21
[    5.372000] ata2: SATA max UDMA/133 cmd 0xe0076180 ctl 0x00000000 bmdma 0x00000000 irq 21
[    5.372000] ata3: SATA max UDMA/133 cmd 0xe0076200 ctl 0x00000000 bmdma 0x00000000 irq 21
[    5.372000] ata4: SATA max UDMA/133 cmd 0xe0076280 ctl 0x00000000 bmdma 0x00000000 irq 21
[    5.400000] usb 2-2: configuration #1 chosen from 1 choice
[    5.420000] scsi4 : SCSI emulation for USB Mass Storage devices
[    5.420000] usb-storage: device found at 2
[    5.420000] usb-storage: waiting for device to settle before scanning
[    5.420000] usbcore: registered new interface driver usb-storage
[    5.420000] USB Mass Storage support registered.
[    5.424000] usbcore: registered new interface driver hiddev
[    5.444000] input: MLK Trust Mouse 15313 as /class/input/input2
[    5.444000] input,hiddev96: USB HID v1.10 Mouse [MLK Trust Mouse 15313] on usb-0000:00:1d.1-2
[    5.444000] usbcore: registered new interface driver usbhid
[    5.444000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[    5.856000] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    5.856000] ata1.00: ATA-7: TOSHIBA MK6034GSX, AH101H, max UDMA/100
[    5.856000] ata1.00: 117231408 sectors, multi 16: LBA48 
[    5.856000] ata1.00: configured for UDMA/100
[    6.168000] ata2: SATA link down (SStatus 0 SControl 0)
[    6.480000] ata3: SATA link down (SStatus 0 SControl 0)
[    6.792000] ata4: SATA link down (SStatus 0 SControl 0)
[    6.792000] scsi 0:0:0:0: Direct-Access     ATA      TOSHIBA MK6034GS AH10 PQ: 0 ANSI: 5
[    6.792000] ata_piix 0000:00:1f.1: version 2.11
[    6.792000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16
[    6.792000] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[    6.792000] scsi5 : ata_piix
[    6.792000] scsi6 : ata_piix
[    6.792000] ata5: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x000160a0 irq 14
[    6.792000] ata6: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x000160a8 irq 15
[    6.800000] sd 0:0:0:0: [sda] 117231408 512-byte hardware sectors (60022 MB)
[    6.800000] sd 0:0:0:0: [sda] Write Protect is off
[    6.800000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    6.800000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.800000] sd 0:0:0:0: [sda] 117231408 512-byte hardware sectors (60022 MB)
[    6.800000] sd 0:0:0:0: [sda] Write Protect is off
[    6.800000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    6.800000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.800000]  sda: sda1 sda2 sda3 < sda5 > sda4
[    6.880000] sd 0:0:0:0: [sda] Attached SCSI disk
[    6.884000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    7.112000] ata5.00: ATAPI: HL-DT-ST DVDRAM GSA-T10N, PC05, max MWDMA2
[    7.160000] Attempting manual resume
[    7.160000] swsusp: Resume From Partition 8:5
[    7.160000] PM: Checking swsusp image.
[    7.160000] PM: Resume from disk failed.
[    7.196000] kjournald starting.  Commit interval 5 seconds
[    7.196000] EXT3-fs: mounted filesystem with ordered data mode.
[    7.284000] ata5.00: configured for MWDMA2
[    7.284000] ata6: port disabled. ignoring.
[    7.288000] scsi 5:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-T10N  PC05 PQ: 0 ANSI: 5
[    7.288000] scsi 5:0:0:0: Attached scsi generic sg1 type 5
[   10.420000] usb-storage: device scan complete
[   10.420000] scsi 4:0:0:0: Direct-Access     SanDisk  Cruzer           7.01 PQ: 0 ANSI: 0 CCS
[   10.420000] sd 4:0:0:0: [sdb] 7954431 512-byte hardware sectors (4073 MB)
[   10.420000] sd 4:0:0:0: [sdb] Write Protect is off
[   10.420000] sd 4:0:0:0: [sdb] Mode Sense: 45 00 00 08
[   10.420000] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   10.424000] sd 4:0:0:0: [sdb] 7954431 512-byte hardware sectors (4073 MB)
[   10.424000] sd 4:0:0:0: [sdb] Write Protect is off
[   10.424000] sd 4:0:0:0: [sdb] Mode Sense: 45 00 00 08
[   10.424000] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[   10.424000]  sdb: sdb1
[   10.424000] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[   10.424000] sd 4:0:0:0: Attached scsi generic sg2 type 0
[   14.340000] Linux agpgart interface v0.102 (c) Dave Jones
[   14.388000] agpgart: Detected an Intel 945GM Chipset.
[   14.388000] agpgart: Detected 7932K stolen memory.
[   14.420000] agpgart: AGP aperture is 256M @ 0xd0000000
[   14.484000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   14.488000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   15.084000] Yenta: CardBus bridge found at 0000:02:06.0 [103c:30aa]
[   15.084000] Yenta: Enabling burst memory read transactions
[   15.084000] Yenta: Using INTVAL to route CSC interrupts to PCI
[   15.084000] Yenta: Routing CardBus interrupts to PCI
[   15.084000] Yenta TI: socket 0000:02:06.0, mfunc 0x01a61b22, devctl 0x64
[   15.140000] intel_rng: FWH not detected
[   15.316000] Yenta: ISA IRQ mask 0x0cf8, PCI irq 17
[   15.316000] Socket status: 30000006
[   15.316000] Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
[   15.316000] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
[   15.316000] cs: IO port probe 0x2000-0x2fff: clean.
[   15.316000] pcmcia: parent PCI bridge Memory window: 0xe8100000 - 0xe83fffff
[   15.316000] pcmcia: parent PCI bridge Memory window: 0x20000000 - 0x23ffffff
[   15.356000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x2580b1, caps: 0xa04793/0x300000
[   15.356000] serio: Synaptics pass-through port at isa0060/serio4/input0
[   15.376000] NET: Registered protocol family 17
[   15.396000] input: SynPS/2 Synaptics TouchPad as /class/input/input3
[   15.396000] input: PC Speaker as /class/input/input4
[   15.408000] iTCO_vendor_support: vendor-support=0
[   15.412000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007)
[   15.412000] iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060)
[   15.412000] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   15.564000] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[   15.564000] Uniform CD-ROM driver Revision: 3.20
[   15.564000] sr 5:0:0:0: Attached scsi CD-ROM sr0
[   15.572000] ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[   15.572000] PCI: Setting latency timer of device 0000:08:00.0 to 64
[   15.624000] cs: IO port probe 0x100-0x3af: clean.
[   15.628000] cs: IO port probe 0x3e0-0x4ff: clean.
[   15.628000] cs: IO port probe 0x820-0x8ff: clean.
[   15.628000] cs: IO port probe 0xc00-0xcf7: clean.
[   15.632000] cs: IO port probe 0xa00-0xaff:<6>ssb: Sonics Silicon Backplane found on PCI device 0000:08:00.0
[   15.632000]  clean.
[   15.964000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 19
[   15.964000] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   16.640000] b44: eth0: Link is up at 100 Mbps, full duplex.
[   16.640000] b44: eth0: Flow control is off for TX and off for RX.
[   16.680000] lp: driver loaded but no devices found
[   17.068000] b43-phy0: Broadcom 4311 WLAN found
[   17.136000] phy0: Selected rate control algorithm 'pid'
[   17.244000] Broadcom 43xx driver loaded [ Features: PML, Firmware-ID: FW13 ]
[   17.344000] Broadcom 43xx-legacy driver loaded [ Features: PID, Firmware-ID: FW10 ]
[   17.384000] Adding 1148608k swap on /dev/sda5.  Priority:-1 extents:1 across:1148608k
[   17.668000] EXT3 FS on sda2, internal journal
[   18.100000] kjournald starting.  Commit interval 5 seconds
[   18.100000] EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
[   18.100000] EXT3 FS on sda1, internal journal
[   18.100000] EXT3-fs: mounted filesystem with ordered data mode.
[   19.236000] ACPI: AC Adapter [C1BA] (on-line)
[   19.244000] ACPI: Video Device [C083] (multi-head: yes  rom: no  post: no)
[   19.260000] No dock devices found.
[   19.348000] input: Power Button (FF) as /class/input/input5
[   19.348000] ACPI: Power Button (FF) [PWRF]
[   19.348000] input: Sleep Button (CM) as /class/input/input6
[   19.348000] ACPI: Sleep Button (CM) [C23F]
[   19.376000] input: Lid Switch as /class/input/input7
[   19.376000] ACPI: Lid Switch [C238]
[   19.424000] ACPI: Battery Slot [C1BC] (battery present)
[   19.424000] ACPI: Battery Slot [C1BB] (battery absent)
[   20.524000] Failure registering capabilities with primary security module.
[   21.344000] ppdev: user-space parallel port driver
[   21.556000] NET: Registered protocol family 10
[   21.556000] lo: Disabled Privacy Extensions
[   21.816000] audit(1213720058.313:3):  type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=5210 profile="/usr/sbin/cupsd"
[   24.980000] apm: BIOS not found.
[   27.004000] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[   27.004000] vboxdrv: Successfully done.
[   30.140000] Bluetooth: Core ver 2.11
[   30.144000] NET: Registered protocol family 31
[   30.144000] Bluetooth: HCI device and connection manager initialized
[   30.144000] Bluetooth: HCI socket layer initialized
[   30.160000] Bluetooth: L2CAP ver 2.8
[   30.160000] Bluetooth: L2CAP socket layer initialized
[   30.276000] Bluetooth: RFCOMM socket layer initialized
[   30.276000] Bluetooth: RFCOMM TTY layer initialized
[   30.276000] Bluetooth: RFCOMM ver 1.8
[   31.600000] eth0: no IPv6 routers present
[   32.824000] [drm] Initialized drm 1.1.0 20060810
[   32.836000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[   32.840000] [drm] Initialized i915 1.6.0 20060119 on minor 0
[   42.244000] usb 2-2: USB disconnect, address 3
[   44.280000] usb 2-2: new low speed USB device using uhci_hcd and address 4
[   44.452000] usb 2-2: configuration #1 chosen from 1 choice
[   44.484000] input: MLK Trust Mouse 15313 as /class/input/input8
[   44.484000] input,hiddev96: USB HID v1.10 Mouse [MLK Trust Mouse 15313] on usb-0000:00:1d.1-2
[  119.148000] usb 2-2: USB disconnect, address 4
[  122.380000] usb 2-2: new low speed USB device using uhci_hcd and address 5
[  122.556000] usb 2-2: configuration #1 chosen from 1 choice
[  122.588000] input: MLK Trust Mouse 15313 as /class/input/input9
[  122.588000] input,hiddev96: USB HID v1.10 Mouse [MLK Trust Mouse 15313] on usb-0000:00:1d.1-2
[  123.332000] usb 2-2: USB disconnect, address 5
[  126.496000] usb 2-2: new low speed USB device using uhci_hcd and address 6
[  126.668000] usb 2-2: configuration #1 chosen from 1 choice
[  126.700000] input: MLK Trust Mouse 15313 as /class/input/input10
[  126.700000] input,hiddev96: USB HID v1.10 Mouse [MLK Trust Mouse 15313] on usb-0000:00:1d.1-2

ifconfig di nuovo

Codice: Seleziona tutto

renato@mbiza-laptop:~$ ifconfig
eth0      Link encap:Ethernet  HWaddr 00:17:A4:D1:68:0B  
          inet addr:192.168.1.3  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::217:a4ff:fed1:680b/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:236 errors:0 dropped:0 overruns:0 frame:0
          TX packets:289 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:108496 (105.9 KB)  TX bytes:57472 (56.1 KB)
          Interrupt:16 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:12 errors:0 dropped:0 overruns:0 frame:0
          TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:600 (600.0 b)  TX bytes:600 (600.0 b)

renato@mbiza-laptop:~$ 

[[lost]-Divilinux]

[  17.068000] b43-phy0: Broadcom 4311 WLAN found
[  17.136000] phy0: Selected rate control algorithm 'pid'
[  17.244000] Broadcom 43xx driver loaded [ Features: PML, Firmware-ID: FW13 ]
[  17.344000] Broadcom 43xx-legacy driver loaded [ Features: PID, Firmware-ID: FW10 ]
a quanto dice il dmesg (per sicurezza cposta anche lspci) hai un chip broadcom 4311, che secondo il link ufficiale dovrebbe essere supportato:

http://wireless.kernel.org/en/users/Drivers/b43

poi viene caricato anche il legacy-driver, che invece e' per modelli piu' vecchi della tua pci-express.
Vediamo se funziona cosi': cancella il firmware della bcm43xx e metti in blacklist i drivers:

Codice: Seleziona tutto

blacklist bcm43xx
blacklist b43legacy

..nel file /etc/modprobe.d/blacklist

Errori di output non ce ne sono, la scheda e' supportata, il firmware e' quello giusto e viene caricato, i driver si caricano normalmente...ora sono curioso di sapere cosa ca**..hemm.."diavolo" sta succedendo...

il

Codice: Seleziona tutto

sudo ifconfig eth1 up

da' sempre errore? l'interfaccia siamo sicuri che sia eth1? (in teoria si ma sai..)
Prova a postare anche il file /etc/network/interfaces

[mbiza]

Codice: Seleziona tutto

renato@mbiza-laptop:~$ sudo ifconfig eth1 up
SIOCSIFFLAGS: Operazione non supportata
renato@mbiza-laptop:~$ sudo ifconfig eth1 up
SIOCSIFFLAGS: Operazione non supportata
renato@mbiza-laptop:~$ cat /etc/network/interfaces
auto lo
iface lo inet loopback

iface eth1 inet dhcp
wireless-channel 1
wireless-mode master
wpa-psk ecc..ecc...

iface eth0 inet dhcp
auto eth0

la scheda è lei

Codice: Seleziona tutto

08:00.0 Network controller: Broadcom Corporation BCM94311MCG wlan mini-PCI (rev 01)

ho provato anche a riavviare ma non cambia nulla...

[[lost]-Divilinux]

inutile anche mettere b43 in /etc/moudules affinche' venga caricato all'avvio..perche' gia' si carica per i fatti suoi.
Quel device mi ricorda qualcosa..cell'ha un mio amico su dell ma alla fine siamo riusciti a farlo aprtire..l'interfaccia era wlan0 comunque..non credo abbia molta importanza...se i driver stanno funzionando l'interfaccia "viene su" da sola

Facciamo cosi'..prova con ndiswrapper e i driver per win..stavolta pero' se non si vede nessuna interfaccia posso cominciare a pensare che la mini-pci non funziona per problemi "tecnici"

[andrjs]

Se hai la 4311 non c'è niente da fare devi usare ndiswrapper come da guida da te citata. Anch'io ho la tua stessa scheda wireless. Se vuoi provare con ndiswrapper fammi sapere.
Ciao

[mbiza]

allora ok, vada per ndiswrapper.
Adesso vado a fare la prima prova d'esame, pozza i' bbè!