(premetto che sono alle prime armi..e che è probabile che il mastz mi stia abbandonando..almeno su windows cominciava a funzionare male..del tipo.."errore di calibrazione nell'alimentazione" e non mi masterizzava i cd, mentre i dvd si.)
Qualcuno è capace di interpretarlo???:(
Codice: Seleziona tutto
System
-----------------------
K3b Version: 1.0.4
KDE Version: 3.5.8
QT Version: 3.3.7
Kernel: 2.6.22-14-generic
Devices
-----------------------
_NEC DVD_RW ND-3500AG 2.18 (/dev/scd0, ) [CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD+R DL] [DVD-ROM, DVD-R sequenziale, DVD-RW a riscrittura limitata, DVD-RW sequenziale, DVD+RW, DVD+R, DVD+R a doppio strato, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96R, RAW/R96R, Riscrittura limitata]
Used versions
-----------------------
cdrecord: 1.1.6
cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/scd0 speed=10 -tao driveropts=burnfree -eject blank=fast -force
cdrecord
-----------------------
/usr/bin/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.
scsidev: '/dev/scd0'
devname: '/dev/scd0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.6
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : '_NEC '
Identification : 'DVD_RW ND-3500AG'
Revision : '2.18'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x002B (DVD+R/DL)
Profile: 0x001B (DVD+R)
Profile: 0x001A (DVD+RW)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0010 (DVD-ROM)
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R)
Profile: 0x0008 (CD-ROM) (current)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96R RAW/R96R
Drive buf size : 1343488 = 1312 KB
Speed set to 1764 KB/s
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 3
Reference speed: 6
Is not unrestricted
Is erasable
Disk sub type: High speed Rewritable (CAV) media (1)
ATIP start of lead in: -11745 (97:25/30)
ATIP start of lead out: 359848 (79:59/73)
1T speed low: 4 1T speed high: 10
2T speed low: 4 2T speed high: 0 (reserved val 6)
power mult factor: 1 5
recommended erase/write power: 5
A1 values: 24 1A D8
A2 values: 26 B2 4A
Disk type: Phase change
Manuf. index: 40
Manufacturer: INFODISC Technology Co., Ltd.
Waiting for drive to calm down.
Starting to write CD/DVD at speed 10.0 in real force BLANK mode for single session.
Last chance to quit, starting real write in 2 seconds.
1 seconds.
0 seconds.
Operation starts.
Errno: 5 (Input/output error), blank unit scsi sendcmd: no error
CDB: A1 01 00 00 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 73 03 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x73 Qual 0x03 (power calibration area error) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 29.156s timeout 9600s
Starting to write CD/DVD at speed 10.0 in real force BLANK mode for single session.
No chance to quit anymore. Operation starts.
Performing OPC...
/usr/bin/wodim: OPC failed.
Blanking PMA, TOC, pregap
Errno: 5 (Input/output error), blank unit scsi sendcmd: no error
CDB: A1 01 00 00 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 73 03 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x73 Qual 0x03 (power calibration area error) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 25.663s timeout 9600s
/usr/bin/wodim: Cannot blank disk, aborting.
/usr/bin/wodim: Some drives do not support all blank types.
/usr/bin/wodim: Try again with wodim blank=all.
