masterizzazione fallita....SEMPRE

Installazione, configurazione e uso di programmi e strumenti.
Scrivi risposta
Avatar utente
smlkat
Prode Principiante
Messaggi: 132
Iscrizione: giovedì 15 marzo 2007, 15:21
Località: Catania

masterizzazione fallita....SEMPRE

Messaggio da smlkat »

ciao a tutti....spero sia un problema di software...
ad ogni modo.
quando provo a masterizzare qualcosa su cd, tipo un divx, arrivato tra il 70-80% mi da sempre errore di masterizzazione.
prima pensavo fosse problema di cd-rw un po graffiato. ma lo fa anche con i cd nuovi (ne ho bruciati 2)
ho provato sia con Brasero, che con K3B, sempre tra 70 e 80% fallisce...
questo è il debug di k3b

Codice: Seleziona tutto

System
-----------------------
K3b Version: 1.0.4

KDE Version: 3.5.9
QT Version:  3.3.8b
Kernel:      2.6.24-20-generic
Devices
-----------------------
MATSHITA UJ-850D 1.00 (/dev/scd0, ) [CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL] [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, Restricted Overwrite, Layer Jump]

K3bIsoImager
-----------------------
mkisofs print size result: 358671 (734558208 bytes)
Pipe throughput: 542616320 bytes read, 542611968 bytes written.

Used versions
-----------------------
mkisofs: 1.1.6
cdrecord: 1.1.6

cdrecord
-----------------------
/usr/bin/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.scsidev: '/dev/scd0'
devname: '/dev/scd0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.6
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   : 
Vendor_info    : 'MATSHITA'
Identification : 'UJ-850D         '
Revision       : '1.00'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x002B (DVD+R/DL) 
Profile: 0x001B (DVD+R) 
Profile: 0x001A (DVD+RW) 
Profile: 0x0016 (DVD-R/DL layer jump recording) 
Profile: 0x0015 (DVD-R/DL sequential recording) 
Profile: 0x0013 (DVD-RW restricted overwrite) 
Profile: 0x0014 (DVD-RW sequential recording) 
Profile: 0x0011 (DVD-R sequential recording) 
Profile: 0x0010 (DVD-ROM) 
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R) 
Profile: 0x0008 (CD-ROM) 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO
Drive buf size : 1310720 = 1280 KB
FIFO size      : 12582912 = 12288 KB
Speed set to 706 KB/s
Track 01: data   700 MB        
Total size:      804 MB (79:42.28) = 358671 sectors
Lout start:      804 MB (79:44/21) = 358671 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 6
  Reference speed: 2
  Is not unrestricted
  Is erasable
  ATIP start of lead in:  -11078 (97:34/22)
  ATIP start of lead out: 359849 (79:59/74)
  1T speed low:  0 (reserved val  0) 1T speed high:  4
  2T speed low:  0 (reserved val  5) 2T speed high:  0 (reserved val 12)
  power mult factor: 3 5
  recommended erase/write power: 3
  A1 values: 02 3A B0
  A2 values: 5C C6 26
Disk type:    Phase change
Manuf. index: 11
Manufacturer: Mitsubishi Chemical Corporation
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 1178
Starting to write CD/DVD at speed   4.0 in real SAO mode for single session.
Last chance to quit, starting real write in  2 seconds.
   1 seconds.
   0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Sending CUE sheet...
Writing pregap for track 1 at -150
Starting new track at sector: 0
Track 01:    0 of  700 MB written.
Track 01:    1 of  700 MB written (fifo 100%) [buf  99%]   4.0x.
Track 01:    2 of  700 MB written (fifo 100%) [buf  99%]   4.1x.
Track 01:    3 of  700 MB written (fifo 100%) [buf  99%]   4.2x.
  fino a
Track 01:  504 of  700 MB written (fifo 100%) [buf  98%]   4.1x.
Track 01:  505 of  700 MB written (fifo 100%) [buf  98%]   4.2x.
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 00 03 F3 9E 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: F1 00 03 00 03 F1 2A 0A 00 13 00 00 10 00 00 00
Sense Key: 0x3 Medium Error, deferred error, Segment 0
Sense Code: 0x10 Qual 0x00 (id crc or ecc error) Fru 0x0
Sense flags: Blk 258346 (valid) 
cmd finished after 0.014s timeout 200s
/usr/bin/wodim: A write error occured.
/usr/bin/wodim: Please properly read the error message above.
write track data: error after 530378752 bytes
Writing  time:  914.011s
Average write speed   5.3x.
Min drive buffer fill was 97%
Fixating...
Fixating time:    0.004s
BURN-Free was never needed.
/usr/bin/wodim: fifo had 8546 puts and 8355 gets.
/usr/bin/wodim: fifo was 0 times empty and 8354 times full, min fill was 99%.

cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/scd0 speed=4 -dao driveropts=burnfree -eject -data -tsize=358671s - 

mkisofs
-----------------------
358671
I: -input-charset not specified, using utf-8 (detected in locale settings)
  0.14% done, estimate finish Wed Aug  6 20:45:28 2008
  qua continua fino a...
 73.61% done, estimate finish Wed Aug  6 20:30:59 2008
 73.75% done, estimate finish Wed Aug  6 20:30:59 2008

mkisofs calculate size command:
-----------------------
/usr/bin/genisoimage -gui -graft-points -print-size -quiet -volid Persepolis -volset  -appid K3B THE CD KREATOR (C) 1998-2006 SEBASTIAN TRUEG AND THE K3B TEAM -publisher  -preparer  -sysid LINUX -volset-size 1 -volset-seqno 1 -sort /tmp/kde-antonio/k3bTAex5b.tmp -rational-rock -hide-list /tmp/kde-antonio/k3bSSdB5a.tmp -joliet -joliet-long -hide-joliet-list /tmp/kde-antonio/k3bKvy3Ub.tmp -no-cache-inodes -full-iso9660-filenames -iso-level 2 -path-list /tmp/kde-antonio/k3b6BTYPb.tmp 

mkisofs command:
-----------------------
/usr/bin/genisoimage -gui -graft-points -volid Persepolis -volset  -appid K3B THE CD KREATOR (C) 1998-2006 SEBASTIAN TRUEG AND THE K3B TEAM -publisher  -preparer  -sysid LINUX -volset-size 1 -volset-seqno 1 -sort /tmp/kde-antonio/k3bIO0qBa.tmp -rational-rock -hide-list /tmp/kde-antonio/k3bYClhfa.tmp -joliet -joliet-long -hide-joliet-list /tmp/kde-antonio/k3bF1PaPb.tmp -no-cache-inodes -full-iso9660-filenames -iso-level 2 -path-list /tmp/kde-antonio/k3boJT7Ba.tmp 

diagnosi??
Nel mondo, tutti nascono con l'amore....solo pinocchio è nato con una sega!
Avatar utente
sim70
Rampante Reduce
Rampante Reduce
Messaggi: 6690
Iscrizione: mercoledì 2 agosto 2006, 18:19
Desktop: mate su eepc
Distribuzione: lubuntu 12.04 64bit su eepc
Località: trentino

Re: masterizzazione fallita....SEMPRE

Messaggio da sim70 »

smlkat ha scritto: ciao a tutti....spero sia un problema di software...
ad ogni modo.
quando provo a masterizzare qualcosa su cd, tipo un divx, arrivato tra il 70-80% mi da sempre errore di masterizzazione.
prima pensavo fosse problema di cd-rw un po graffiato. ma lo fa anche con i cd nuovi (ne ho bruciati 2)
ho provato sia con Brasero, che con K3B, sempre tra 70 e 80% fallisce...
questo è il debug di k3b

Codice: Seleziona tutto

System
-----------------------
K3b Version: 1.0.4

KDE Version: 3.5.9
QT Version:  3.3.8b
Kernel:      2.6.24-20-generic
Devices
-----------------------
MATSHITA UJ-850D 1.00 (/dev/scd0, ) [CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL] [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, Restricted Overwrite, Layer Jump]

K3bIsoImager
-----------------------
mkisofs print size result: 358671 (734558208 bytes)
Pipe throughput: 542616320 bytes read, 542611968 bytes written.

Used versions
-----------------------
mkisofs: 1.1.6
cdrecord: 1.1.6

cdrecord
-----------------------
/usr/bin/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.scsidev: '/dev/scd0'
devname: '/dev/scd0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.6
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   : 
Vendor_info    : 'MATSHITA'
Identification : 'UJ-850D         '
Revision       : '1.00'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x000A (CD-RW)
Profile: 0x002B (DVD+R/DL) 
Profile: 0x001B (DVD+R) 
Profile: 0x001A (DVD+RW) 
Profile: 0x0016 (DVD-R/DL layer jump recording) 
Profile: 0x0015 (DVD-R/DL sequential recording) 
Profile: 0x0013 (DVD-RW restricted overwrite) 
Profile: 0x0014 (DVD-RW sequential recording) 
Profile: 0x0011 (DVD-R sequential recording) 
Profile: 0x0010 (DVD-ROM) 
Profile: 0x000A (CD-RW) (current)
Profile: 0x0009 (CD-R) 
Profile: 0x0008 (CD-ROM) 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO
Drive buf size : 1310720 = 1280 KB
FIFO size      : 12582912 = 12288 KB
Speed set to 706 KB/s
Track 01: data   700 MB        
Total size:      804 MB (79:42.28) = 358671 sectors
Lout start:      804 MB (79:44/21) = 358671 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 6
  Reference speed: 2
  Is not unrestricted
  Is erasable
  ATIP start of lead in:  -11078 (97:34/22)
  ATIP start of lead out: 359849 (79:59/74)
  1T speed low:  0 (reserved val  0) 1T speed high:  4
  2T speed low:  0 (reserved val  5) 2T speed high:  0 (reserved val 12)
  power mult factor: 3 5
  recommended erase/write power: 3
  A1 values: 02 3A B0
  A2 values: 5C C6 26
Disk type:    Phase change
Manuf. index: 11
Manufacturer: Mitsubishi Chemical Corporation
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 1178
Starting to write CD/DVD at speed   4.0 in real SAO mode for single session.
Last chance to quit, starting real write in  2 seconds.
   1 seconds.
   0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Sending CUE sheet...
Writing pregap for track 1 at -150
Starting new track at sector: 0
Track 01:    0 of  700 MB written.
Track 01:    1 of  700 MB written (fifo 100%) [buf  99%]   4.0x.
Track 01:    2 of  700 MB written (fifo 100%) [buf  99%]   4.1x.
Track 01:    3 of  700 MB written (fifo 100%) [buf  99%]   4.2x.
  fino a
Track 01:  504 of  700 MB written (fifo 100%) [buf  98%]   4.1x.
Track 01:  505 of  700 MB written (fifo 100%) [buf  98%]   4.2x.
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 00 03 F3 9E 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: F1 00 03 00 03 F1 2A 0A 00 13 00 00 10 00 00 00
Sense Key: 0x3 Medium Error, deferred error, Segment 0
Sense Code: 0x10 Qual 0x00 (id crc or ecc error) Fru 0x0
Sense flags: Blk 258346 (valid) 
cmd finished after 0.014s timeout 200s
/usr/bin/wodim: A write error occured.
/usr/bin/wodim: Please properly read the error message above.
write track data: error after 530378752 bytes
Writing  time:  914.011s
Average write speed   5.3x.
Min drive buffer fill was 97%
Fixating...
Fixating time:    0.004s
BURN-Free was never needed.
/usr/bin/wodim: fifo had 8546 puts and 8355 gets.
/usr/bin/wodim: fifo was 0 times empty and 8354 times full, min fill was 99%.

cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/scd0 speed=4 -dao driveropts=burnfree -eject -data -tsize=358671s - 

mkisofs
-----------------------
358671
I: -input-charset not specified, using utf-8 (detected in locale settings)
  0.14% done, estimate finish Wed Aug  6 20:45:28 2008
  qua continua fino a...
 73.61% done, estimate finish Wed Aug  6 20:30:59 2008
 73.75% done, estimate finish Wed Aug  6 20:30:59 2008

mkisofs calculate size command:
-----------------------
/usr/bin/genisoimage -gui -graft-points -print-size -quiet -volid Persepolis -volset  -appid K3B THE CD KREATOR (C) 1998-2006 SEBASTIAN TRUEG AND THE K3B TEAM -publisher  -preparer  -sysid LINUX -volset-size 1 -volset-seqno 1 -sort /tmp/kde-antonio/k3bTAex5b.tmp -rational-rock -hide-list /tmp/kde-antonio/k3bSSdB5a.tmp -joliet -joliet-long -hide-joliet-list /tmp/kde-antonio/k3bKvy3Ub.tmp -no-cache-inodes -full-iso9660-filenames -iso-level 2 -path-list /tmp/kde-antonio/k3b6BTYPb.tmp 

mkisofs command:
-----------------------
/usr/bin/genisoimage -gui -graft-points -volid Persepolis -volset  -appid K3B THE CD KREATOR (C) 1998-2006 SEBASTIAN TRUEG AND THE K3B TEAM -publisher  -preparer  -sysid LINUX -volset-size 1 -volset-seqno 1 -sort /tmp/kde-antonio/k3bIO0qBa.tmp -rational-rock -hide-list /tmp/kde-antonio/k3bYClhfa.tmp -joliet -joliet-long -hide-joliet-list /tmp/kde-antonio/k3bF1PaPb.tmp -no-cache-inodes -full-iso9660-filenames -iso-level 2 -path-list /tmp/kde-antonio/k3boJT7Ba.tmp 

diagnosi??
Lo fà anche a mè, ma in modo diverso, io risolvo parzialmente, riducendo la velocità di masterizzazione e dando sempre la msterizzazione con la scrittura dao, cioè non multisessione, perchè se faccio miultisessione mi dà problemi, invece con la live di kubuntu 6.10, non mi dà nessun problema, dopo che ho installato la hardy, k3b mi dà problemi con le librerie di masterizzazione, sembra quasi che on comunichi bene col masterizzatore, poi ho cambiato i permessi alle librerie di scrittura seguendo un topic vecchio, ma non ho risolto.  :-\
Avatar utente
foreveropensource
Prode Principiante
Messaggi: 20
Iscrizione: lunedì 4 agosto 2008, 17:41

Re: masterizzazione fallita....SEMPRE

Messaggio da foreveropensource »

fa´cosi´solo coi cd o con ogni genere di supporto? a me brasero funziona solo con dvd e cd-rw, coi cd-r non ne vuole sapere, e gnome baker altrettanto....;  ???
shouldes
Tenace Tecnocrate
Tenace Tecnocrate
Messaggi: 19490
Iscrizione: domenica 10 febbraio 2008, 21:45

Re: masterizzazione fallita....SEMPRE

Messaggio da shouldes »

Aprite il case e controllate se non si sia allentato qualche spinotto dietro il masterizzatore, se ancora bruciano i cd provate gnomebacker, che di default lascia i cd aperti.
Avatar utente
sim70
Rampante Reduce
Rampante Reduce
Messaggi: 6690
Iscrizione: mercoledì 2 agosto 2006, 18:19
Desktop: mate su eepc
Distribuzione: lubuntu 12.04 64bit su eepc
Località: trentino

Re: masterizzazione fallita....SEMPRE

Messaggio da sim70 »

shouldes ha scritto: Aprite il case e controllate se non si sia allentato qualche spinotto dietro il masterizzatore, se ancora bruciano i cd provate gnomebacker, che di default lascia i cd aperti.
Già fatto a suo tempo, morale, brucia 4 ogni 1 di masterizzato, è proprio con la hardy che non funzia, perchè ripeto, se uso la live di6.10 (gutsy? non ricordo) funzia alla grande.
Avatar utente
telperion
Rampante Reduce
Rampante Reduce
Messaggi: 5407
Iscrizione: lunedì 10 luglio 2006, 18:20

Re: masterizzazione fallita....SEMPRE

Messaggio da telperion »

sim70 ha scritto:
shouldes ha scritto: Aprite il case e controllate se non si sia allentato qualche spinotto dietro il masterizzatore, se ancora bruciano i cd provate gnomebacker, che di default lascia i cd aperti.
Già fatto a suo tempo, morale, brucia 4 ogni 1 di masterizzato, è proprio con la hardy che non funzia, perchè ripeto, se uso la live di6.10 (gutsy? non ricordo) funzia alla grande.
Prova a commentare con # la riga del masterizzatore in /etc/fstab perchè in ambiente grafico ora è hal che provvede a montare i dispositivi eimovibili e quella riga può dare problemi.
Avatar utente
sim70
Rampante Reduce
Rampante Reduce
Messaggi: 6690
Iscrizione: mercoledì 2 agosto 2006, 18:19
Desktop: mate su eepc
Distribuzione: lubuntu 12.04 64bit su eepc
Località: trentino

Re: masterizzazione fallita....SEMPRE

Messaggio da sim70 »

telperion ha scritto:
sim70 ha scritto:
shouldes ha scritto: Aprite il case e controllate se non si sia allentato qualche spinotto dietro il masterizzatore, se ancora bruciano i cd provate gnomebacker, che di default lascia i cd aperti.
Già fatto a suo tempo, morale, brucia 4 ogni 1 di masterizzato, è proprio con la hardy che non funzia, perchè ripeto, se uso la live di6.10 (gutsy? non ricordo) funzia alla grande.
Prova a commentare con # la riga del masterizzatore in /etc/fstab perchè in ambiente grafico ora è hal che provvede a montare i dispositivi eimovibili e quella riga può dare problemi.
Fatto anche quello, ed addirittura cancellato le righe (ho un lettore ed un masterizzatore), ma non và nemmeno a pacche, mi sà che è un bug o un errore di percorso, ripeto fino alla 7.10 andava ttto alla grande, ora ci sono problemi, e non solo per mè.
shouldes
Tenace Tecnocrate
Tenace Tecnocrate
Messaggi: 19490
Iscrizione: domenica 10 febbraio 2008, 21:45

Re: masterizzazione fallita....SEMPRE

Messaggio da shouldes »

sim70 ha scritto:
telperion ha scritto:
sim70 ha scritto:
shouldes ha scritto: Aprite il case e controllate se non si sia allentato qualche spinotto dietro il masterizzatore, se ancora bruciano i cd provate gnomebacker, che di default lascia i cd aperti.
Già fatto a suo tempo, morale, brucia 4 ogni 1 di masterizzato, è proprio con la hardy che non funzia, perchè ripeto, se uso la live di6.10 (gutsy? non ricordo) funzia alla grande.
Prova a commentare con # la riga del masterizzatore in /etc/fstab perchè in ambiente grafico ora è hal che provvede a montare i dispositivi eimovibili e quella riga può dare problemi.
Fatto anche quello, ed addirittura cancellato le righe (ho un lettore ed un masterizzatore), ma non và nemmeno a pacche, mi sà che è un bug o un errore di percorso, ripeto fino alla 7.10 andava ttto alla grande, ora ci sono problemi, e non solo per mè.
Prova a mettere lettore e masterizzatore su due canali ide differenti, non so per quale strano motivo, ma io su un pc ho risolto tutti i miei problemi di masterizzazione dopo aver spostato il lettore.
Avatar utente
Nocchy
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 336
Iscrizione: martedì 3 ottobre 2006, 13:27
Desktop: Gnome
Distribuzione: Ubuntu 18.04 64bit
Sesso: Maschile
Località: Catania

Re: masterizzazione fallita....SEMPRE

Messaggio da Nocchy »

Lo faceva anche a me....improvvisamente....addirittura esegue tutto il processo e poi il cd/dvd risulta vuoto....ma io ho risolto  (rotfl) Ho comprato per €21,00 un nuovo masterizzatore e come per magia tutto risolto!!  ;D
A parte gli scherzi forse è un problema di aggiornamento del firmware....il mio era vecchio 4 anni e non ne ho trovati di nuovi...
Avatar utente
smlkat
Prode Principiante
Messaggi: 132
Iscrizione: giovedì 15 marzo 2007, 15:21
Località: Catania

Re: masterizzazione fallita....SEMPRE

Messaggio da smlkat »

purtroppo io sono su un notebook di seconda mano....e il lettore non è quello originale del pc...non so il modello...dovrei smontarlo e vedere....
Nel mondo, tutti nascono con l'amore....solo pinocchio è nato con una sega!
Scrivi risposta

Ritorna a “Applicazioni”

Chi c’è in linea

Visualizzano questa sezione: Google [Bot], Majestic-12 [Bot] e 7 ospiti