driver GeForce FX Go5650

Riconoscimento, installazione e configurazione delle periferiche.
Jack_ut
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 1698
Iscrizione: giovedì 6 novembre 2008, 15:29

Re: driver GeForce FX Go5650

Messaggio da Jack_ut »

Se hai provato ad installare i drivers con envy, hai poi proceduto alla loro disinstallazione? Sempre tramite envy, potresti provare da terminale con

Codice: Seleziona tutto

sudo envyng --uninstall-all
Da synaptic puoi ancora disinstallare nvidia-settings

Riavvia in recovery mode e usa l'opzione xfix e dopo prova nuovamente, e spero per l'ultima volta, a reinstallare i drivers dal punto che ti avevo suggerito in precedenza. Al termine dell'installazione, dai prima il comando

Codice: Seleziona tutto

sudo nvidia-xconfig
e poi

Codice: Seleziona tutto

sudo /etc/init.d/gdm start
P.S.
Questa volta dimmi che è andato tutto bene... >:( >:( >:(
Avatar utente
ilmarchi
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 474
Iscrizione: giovedì 6 novembre 2008, 19:36

Re: driver GeForce FX Go5650

Messaggio da ilmarchi »

dunque seguendo alla lettera cio che mi hai scritto ho eseguito il primo comando da terminale poi ho disinstallato da synaptic nvidia-setting poi ho riavviato in recovery mode ma quando seleziono l'opzione xfix parte una schermata nera con delle scritte poi ritorna subito sull'opzione della scelta rivado sempre su xfix ma torna sempre a capo
Jack_ut
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 1698
Iscrizione: giovedì 6 novembre 2008, 15:29

Re: driver GeForce FX Go5650

Messaggio da Jack_ut »

Prova a farlo partire normalmente e vedere se va, nel caso ti ritrovassi in console, autenticati e reinstalla i drivers.

Se si riavvia normalmente, controlla il tuo xorg.conf e vedi se sono indicati i driver nvidia, per vedere poi se sono caricati correttamente

Codice: Seleziona tutto

glxinfo |grep rendering
Se la risposta è "yes" avvia nvidia-settings

Codice: Seleziona tutto

sudo nvidia-settings
e vedi se vengono riconosciute anche le risoluzioni del monitor.

Altrimenti spiegami meglio la situazione
Avatar utente
ilmarchi
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 474
Iscrizione: giovedì 6 novembre 2008, 19:36

Re: driver GeForce FX Go5650

Messaggio da ilmarchi »

no porc. putt. non va e basta ho rifatto l'installazione dal punto che mi hai indicato ma non si riesce a capire perchè nonostante mi dica che l'installazione dei driver sia andata a buon fine al termine ri riavvia sempre in low graphic mode
Jack_ut
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 1698
Iscrizione: giovedì 6 novembre 2008, 15:29

Re: driver GeForce FX Go5650

Messaggio da Jack_ut »

Mi potresti ripostare (per l'ennesima volta) il tuo xorg.conf attuale ed in più marca e modello del tuo notebook?
Avatar utente
ilmarchi
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 474
Iscrizione: giovedì 6 novembre 2008, 19:36

Re: driver GeForce FX Go5650

Messaggio da ilmarchi »

Codice: Seleziona tutto

# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig:  version 1.0  (buildmeister@builder63)  Mon Mar  2 12:45:55 PST 2009


Section "ServerLayout"
    Identifier     "Layout0"
    Screen      0  "Screen0" 0 0
    InputDevice    "Keyboard0" "CoreKeyboard"
    InputDevice    "Mouse0" "CorePointer"
EndSection

Section "Files"
EndSection

Section "Module"
    Load           "dbe"
    Load           "extmod"
    Load           "type1"
    Load           "freetype"
    Load           "glx"
EndSection

Section "InputDevice"

    # generated from default
    Identifier     "Mouse0"
    Driver         "mouse"
    Option         "Protocol" "auto"
    Option         "Device" "/dev/psaux"
    Option         "Emulate3Buttons" "no"
    Option         "ZAxisMapping" "4 5"
EndSection

Section "InputDevice"

    # generated from default
    Identifier     "Keyboard0"
    Driver         "kbd"
EndSection

Section "Monitor"
    Identifier     "Monitor0"
    VendorName     "Unknown"
    ModelName      "Unknown"
    HorizSync       30.0 - 110.0
    VertRefresh     50.0 - 150.0
    Option         "DPMS"
EndSection

Section "Device"
    Identifier     "Device0"
    Driver         "nvidia"
    VendorName     "NVIDIA Corporation"
EndSection

Section "Screen"
    Identifier     "Screen0"
    Device         "Device0"
    Monitor        "Monitor0"
    DefaultDepth    24
    SubSection     "Display"
        Depth       24
    EndSubSection
EndSection

la marca è asus il modello L5D
Jack_ut
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 1698
Iscrizione: giovedì 6 novembre 2008, 15:29

Re: driver GeForce FX Go5650

Messaggio da Jack_ut »

Il tuo xorg è ok, ma dobbiamo capire perchè non ti vuole caricare i drivers, postami allora il contenuto di di

Codice: Seleziona tutto

cat /var/log/Xorg.0.log
e riprova anche

Codice: Seleziona tutto

glxinfo |grep rendering
Avatar utente
ilmarchi
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 474
Iscrizione: giovedì 6 novembre 2008, 19:36

Re: driver GeForce FX Go5650

Messaggio da ilmarchi »

Codice: Seleziona tutto

	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 320
	XResolution: 320
	YResolution: 400
	XCharSize: 8
	YCharSize: 16
	NumberOfPlanes: 1
	BitsPerPixel: 8
	NumberOfBanks: 1
	MemoryModel: 4
	BankSize: 0
	NumberOfImages: 30
	RedMaskSize: 0
	RedFieldPosition: 0
	GreenMaskSize: 0
	GreenFieldPosition: 0
	BlueMaskSize: 0
	BlueFieldPosition: 0
	RsvdMaskSize: 0
	RsvdFieldPosition: 0
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 320
	BnkNumberOfImagePages: 30
	LinNumberOfImagePages: 30
	LinRedMaskSize: 0
	LinRedFieldPosition: 0
	LinGreenMaskSize: 0
	LinGreenFieldPosition: 0
	LinBlueMaskSize: 0
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 0
	LinRsvdFieldPosition: 0
	MaxPixelClock: 229500000
Mode: 132 (320x400)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 640
	XResolution: 320
	YResolution: 400
	XCharSize: 8
	YCharSize: 16
	NumberOfPlanes: 1
	BitsPerPixel: 16
	NumberOfBanks: 1
	MemoryModel: 6
	BankSize: 0
	NumberOfImages: 14
	RedMaskSize: 5
	RedFieldPosition: 11
	GreenMaskSize: 6
	GreenFieldPosition: 5
	BlueMaskSize: 5
	BlueFieldPosition: 0
	RsvdMaskSize: 0
	RsvdFieldPosition: 0
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 640
	BnkNumberOfImagePages: 14
	LinNumberOfImagePages: 14
	LinRedMaskSize: 5
	LinRedFieldPosition: 11
	LinGreenMaskSize: 6
	LinGreenFieldPosition: 5
	LinBlueMaskSize: 5
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 0
	LinRsvdFieldPosition: 0
	MaxPixelClock: 229500000
*Mode: 133 (320x400)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 1280
	XResolution: 320
	YResolution: 400
	XCharSize: 8
	YCharSize: 16
	NumberOfPlanes: 1
	BitsPerPixel: 32
	NumberOfBanks: 1
	MemoryModel: 6
	BankSize: 0
	NumberOfImages: 6
	RedMaskSize: 8
	RedFieldPosition: 16
	GreenMaskSize: 8
	GreenFieldPosition: 8
	BlueMaskSize: 8
	BlueFieldPosition: 0
	RsvdMaskSize: 8
	RsvdFieldPosition: 24
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 1280
	BnkNumberOfImagePages: 6
	LinNumberOfImagePages: 6
	LinRedMaskSize: 8
	LinRedFieldPosition: 16
	LinGreenMaskSize: 8
	LinGreenFieldPosition: 8
	LinBlueMaskSize: 8
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 8
	LinRsvdFieldPosition: 24
	MaxPixelClock: 229500000
Mode: 134 (320x240)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 320
	XResolution: 320
	YResolution: 240
	XCharSize: 8
	YCharSize: 8
	NumberOfPlanes: 1
	BitsPerPixel: 8
	NumberOfBanks: 1
	MemoryModel: 4
	BankSize: 0
	NumberOfImages: 30
	RedMaskSize: 0
	RedFieldPosition: 0
	GreenMaskSize: 0
	GreenFieldPosition: 0
	BlueMaskSize: 0
	BlueFieldPosition: 0
	RsvdMaskSize: 0
	RsvdFieldPosition: 0
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 320
	BnkNumberOfImagePages: 30
	LinNumberOfImagePages: 30
	LinRedMaskSize: 0
	LinRedFieldPosition: 0
	LinGreenMaskSize: 0
	LinGreenFieldPosition: 0
	LinBlueMaskSize: 0
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 0
	LinRsvdFieldPosition: 0
	MaxPixelClock: 229500000
Mode: 135 (320x240)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 640
	XResolution: 320
	YResolution: 240
	XCharSize: 8
	YCharSize: 8
	NumberOfPlanes: 1
	BitsPerPixel: 16
	NumberOfBanks: 1
	MemoryModel: 6
	BankSize: 0
	NumberOfImages: 19
	RedMaskSize: 5
	RedFieldPosition: 11
	GreenMaskSize: 6
	GreenFieldPosition: 5
	BlueMaskSize: 5
	BlueFieldPosition: 0
	RsvdMaskSize: 0
	RsvdFieldPosition: 0
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 640
	BnkNumberOfImagePages: 19
	LinNumberOfImagePages: 19
	LinRedMaskSize: 5
	LinRedFieldPosition: 11
	LinGreenMaskSize: 6
	LinGreenFieldPosition: 5
	LinBlueMaskSize: 5
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 0
	LinRsvdFieldPosition: 0
	MaxPixelClock: 229500000
*Mode: 136 (320x240)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 1280
	XResolution: 320
	YResolution: 240
	XCharSize: 8
	YCharSize: 8
	NumberOfPlanes: 1
	BitsPerPixel: 32
	NumberOfBanks: 1
	MemoryModel: 6
	BankSize: 0
	NumberOfImages: 10
	RedMaskSize: 8
	RedFieldPosition: 16
	GreenMaskSize: 8
	GreenFieldPosition: 8
	BlueMaskSize: 8
	BlueFieldPosition: 0
	RsvdMaskSize: 8
	RsvdFieldPosition: 24
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 1280
	BnkNumberOfImagePages: 10
	LinNumberOfImagePages: 10
	LinRedMaskSize: 8
	LinRedFieldPosition: 16
	LinGreenMaskSize: 8
	LinGreenFieldPosition: 8
	LinBlueMaskSize: 8
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 8
	LinRsvdFieldPosition: 24
	MaxPixelClock: 229500000
Mode: 13d (640x400)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 1280
	XResolution: 640
	YResolution: 400
	XCharSize: 8
	YCharSize: 16
	NumberOfPlanes: 1
	BitsPerPixel: 16
	NumberOfBanks: 1
	MemoryModel: 6
	BankSize: 0
	NumberOfImages: 6
	RedMaskSize: 5
	RedFieldPosition: 11
	GreenMaskSize: 6
	GreenFieldPosition: 5
	BlueMaskSize: 5
	BlueFieldPosition: 0
	RsvdMaskSize: 0
	RsvdFieldPosition: 0
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 1280
	BnkNumberOfImagePages: 6
	LinNumberOfImagePages: 6
	LinRedMaskSize: 5
	LinRedFieldPosition: 11
	LinGreenMaskSize: 6
	LinGreenFieldPosition: 5
	LinBlueMaskSize: 5
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 0
	LinRsvdFieldPosition: 0
	MaxPixelClock: 229500000
*Mode: 13e (640x400)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 2560
	XResolution: 640
	YResolution: 400
	XCharSize: 8
	YCharSize: 16
	NumberOfPlanes: 1
	BitsPerPixel: 32
	NumberOfBanks: 1
	MemoryModel: 6
	BankSize: 0
	NumberOfImages: 2
	RedMaskSize: 8
	RedFieldPosition: 16
	GreenMaskSize: 8
	GreenFieldPosition: 8
	BlueMaskSize: 8
	BlueFieldPosition: 0
	RsvdMaskSize: 8
	RsvdFieldPosition: 24
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 2560
	BnkNumberOfImagePages: 2
	LinNumberOfImagePages: 2
	LinRedMaskSize: 8
	LinRedFieldPosition: 16
	LinGreenMaskSize: 8
	LinGreenFieldPosition: 8
	LinBlueMaskSize: 8
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 8
	LinRsvdFieldPosition: 24
	MaxPixelClock: 229500000

(II) VESA(0): Total Memory: 1024 64KB banks (65536kB)
(II) VESA(0): Configured Monitor: Using default hsync range of 31.50-37.90 kHz
(II) VESA(0): Configured Monitor: Using default vrefresh range of 50.00-70.00 Hz
(WW) VESA(0): Unable to estimate virtual size
(II) VESA(0): Not using built-in mode "1024x768" (no mode of this name)
(II) VESA(0): Not using built-in mode "800x600" (no mode of this name)
(II) VESA(0): Not using built-in mode "640x480" (no mode of this name)
(II) VESA(0): Not using built-in mode "640x400" (no mode of this name)
(II) VESA(0): Not using built-in mode "320x400" (no mode of this name)
(II) VESA(0): Not using built-in mode "320x240" (no mode of this name)
(II) VESA(0): Not using built-in mode "320x200" (no mode of this name)
(WW) VESA(0): No valid modes left.  Trying less strict filter...
(II) VESA(0): Configured Monitor: Using hsync range of 31.50-37.90 kHz
(II) VESA(0): Configured Monitor: Using vrefresh range of 50.00-70.00 Hz
(WW) VESA(0): Unable to estimate virtual size
(II) VESA(0): Not using built-in mode "1024x768" (hsync out of range)
(II) VESA(0): Not using built-in mode "640x400" (hsync out of range)
(II) VESA(0): Not using built-in mode "320x400" (hsync out of range)
(II) VESA(0): Not using built-in mode "320x240" (illegal horizontal timings)
(II) VESA(0): Not using built-in mode "320x200" (illegal horizontal timings)
(--) VESA(0): Virtual size is 800x600 (pitch 800)
(**) VESA(0): *Built-in mode "800x600"
(**) VESA(0): *Built-in mode "640x480"
(==) VESA(0): DPI set to (96, 96)
(II) VESA(0): Attempting to use 60Hz refresh for mode "800x600" (115)
(II) VESA(0): Attempting to use 60Hz refresh for mode "640x480" (112)
(**) VESA(0): Using "Shadow Framebuffer"
(II) Loading sub module "shadow"
(II) LoadModule: "shadow"

(II) Loading /usr/lib/xorg/modules//libshadow.so
(II) Module shadow: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.1.0
	ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "fb"
(II) LoadModule: "fb"

(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	ABI class: X.Org ANSI C Emulation, version 0.4
(==) Depth 24 pixmap format is 32 bpp
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[5] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[6] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[7] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[8] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[9] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[10] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[11] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[12] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[13] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[14] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[15] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[16] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[17] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[18] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[19] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[20] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[21] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[22] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[23] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[24] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[25] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[26] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[27] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[28] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[29] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
(II) Loading sub module "int10"
(II) LoadModule: "int10"

(II) Reloading /usr/lib/xorg/modules//libint10.so
(II) VESA(0): initializing int10
(II) VESA(0): Primary V_BIOS segment is: 0xc000
(II) VESA(0): VESA BIOS detected
(II) VESA(0): VESA VBE Version 3.0
(II) VESA(0): VESA VBE Total Mem: 65536 kB
(II) VESA(0): VESA VBE OEM: NVIDIA
(II) VESA(0): VESA VBE OEM Software Rev: 4.49
(II) VESA(0): VESA VBE OEM Vendor: NVIDIA Corporation
(II) VESA(0): VESA VBE OEM Product: NV31 Board - e133n   
(II) VESA(0): VESA VBE OEM Product Rev: Chip Rev   
(II) VESA(0): virtual address = 0xb2ad2000,
	physical address = 0xd0000000, size = 67108864
(==) VESA(0): Default visual is TrueColor
(==) VESA(0): Backing store disabled
(II) VESA(0): DPMS enabled
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found)
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"

(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 2.0.99
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 2.1
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Configuring as mouse
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) config/hal: Adding input device SynPS/2 Synaptics TouchPad
(II) LoadModule: "synaptics"

(II) Loading /usr/lib/xorg/modules/input//synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 0.15.2
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 2.1
(II) Synaptics touchpad driver version 0.15.2
(II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
(II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
(**) Option "Device" "/dev/input/event8"
(--) SynPS/2 Synaptics TouchPad touchpad found
(**) SynPS/2 Synaptics TouchPad: always reports core events
(II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
(II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
(II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
(--) SynPS/2 Synaptics TouchPad touchpad found
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) AT Translated Set 2 keyboard: xkb_rules: "evdev"
(**) Option "xkb_model" "pc105"
(**) AT Translated Set 2 keyboard: xkb_model: "pc105"
(**) Option "xkb_layout" "it"
(**) AT Translated Set 2 keyboard: xkb_layout: "it"
(II) config/hal: Adding input device Video Bus
(**) Video Bus: always reports core events
(**) Video Bus: Device: "/dev/input/event7"
(II) Video Bus: Found keys
(II) Video Bus: Configuring as keyboard
(II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Video Bus: xkb_rules: "evdev"
(**) Option "xkb_model" "pc105"
(**) Video Bus: xkb_model: "pc105"
(**) Option "xkb_layout" "it"
(**) Video Bus: xkb_layout: "it"
AUDIT: Sat Apr  4 22:58:01 2009: 5280 X: client 4 rejected from local host ( uid=0 gid=0 pid=5299 )
AUDIT: Sat Apr  4 22:58:09 2009: 5280 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=5301 )
AUDIT: Sat Apr  4 22:58:09 2009: 5280 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=5302 )
AUDIT: Sat Apr  4 22:58:09 2009: 5280 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=5303 )
alessia@alessia-laptop:~$ 

Codice: Seleziona tutto

alessia@alessia-laptop:~$ glxinfo |grep rendering
Xlib:  extension "GLX" missing on display ":0.0".
Xlib:  extension "GLX" missing on display ":0.0".
Xlib:  extension "GLX" missing on display ":0.0".
Xlib:  extension "GLX" missing on display ":0.0".
Xlib:  extension "GLX" missing on display ":0.0".
Error: couldn't find RGB GLX visual or fbconfig
Xlib:  extension "GLX" missing on display ":0.0".
Xlib:  extension "GLX" missing on display ":0.0".
Xlib:  extension "GLX" missing on display ":0.0".
Xlib:  extension "GLX" missing on display ":0.0".
Xlib:  extension "GLX" missing on display ":0.0".
alessia@alessia-laptop:~$ 
Ultima modifica di ilmarchi il sabato 4 aprile 2009, 23:05, modificato 1 volta in totale.
Jack_ut
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 1698
Iscrizione: giovedì 6 novembre 2008, 15:29

Re: driver GeForce FX Go5650

Messaggio da Jack_ut »

Dal log di Xorg è evidente che nessun driver nvidia viene caricato e che vengono usati invece i vesa.
A questo punto ti proporrei di disinstallare prima il driver e poi reinstallarlo, e vediamo se migliora qualcosa.

Dai ctrl-alt-f1 (così passi in console) e loggati, arresti il server X, ti sposti nella cartella dove è contenuto il pacchetto del driver .run (do per scontato sia la home) e lo disinstalli

Codice: Seleziona tutto

sudo /etc/init.d/gdm stop
cd ~
sudo sh NVIDIA-Linux-x86-173.14.18-pkg1.run --uninstall
Poi procedi alla reinstallazione (rispondi si a tutto)

Codice: Seleziona tutto

sudo sh NVIDIA-Linux-x86-173.14.18-pkg1.run
ed infine riavvii X

Codice: Seleziona tutto

sudo nvidia-xconfig
sudo /etc/init.d/gdm start
Dop aver riavviato l'interfaccia grafica postami il contenuto di /var/log/nvidia-installer.log

Codice: Seleziona tutto

cat /var/log/nvidia-installer.log
Sta veramente diventando un circolo vizioso ::)
Ultima modifica di Jack_ut il domenica 5 aprile 2009, 5:05, modificato 1 volta in totale.
Avatar utente
ilmarchi
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 474
Iscrizione: giovedì 6 novembre 2008, 19:36

Re: driver GeForce FX Go5650

Messaggio da ilmarchi »

Codice: Seleziona tutto

    from include/asm-generic/pci-dma-compat.h:7,
                    from include/asm/pci.h:94,
                    from include/linux/pci.h:989,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:86,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/os-agp.c:24:
   include/linux/scatterlist.h: In function ‘sg_virt’:
   include/linux/scatterlist.h:199: warning: pointer of type ‘void *’ used 
   in arithmetic
   In file included from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:113,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/os-agp.c:24:
   include/linux/highmem.h: In function ‘zero_user_segments’:
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
     cc -Wp,-MD,/tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/.os-
   interface.o.d  -nostdinc -isystem /usr/lib/gcc/i486-linux-gnu/4.3.2/include 
   -D__KERNEL__  -Iinclude  -I/usr/src/linux-headers-2.6.27-11-generic/arch/x86
   /include -include include/linux/autoconf.h -Iubuntu/include  -Wall -Wundef -
   Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -Werror-i
   mplicit-function-declaration -O2 -m32 -msoft-float -mregparm=3 -freg-struct-
   return -mpreferred-stack-boundary=2 -march=i586 -mtune=generic -ffreestandin
   g -pipe -Wno-sign-compare -fno-asynchronous-unwind-tables -mno-sse -mno-mmx 
   -mno-sse2 -mno-3dnow -Iinclude/asm-x86/mach-default -fno-stack-protector -fn
   o-omit-frame-p
   ointer -fno-optimize-sibling-calls -pg -Wdeclaration-after-statement -Wno-po
   inter-sign -I/tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv -Wal
   l -Wimplicit -Wreturn-type -Wswitch -Wformat -Wchar-subscripts -Wparentheses
   -Wpointer-arith -Wno-multichar -Werror -MD -Wsign-compare -Wno-cast-qual -Wn
   o-error -D__KERNEL__ -DMODULE -DNVRM -DNV_VERSION_STRING=\"173.14.18\" -UDEB
   UG -U_DEBUG -DNDEBUG -DMODULE -D"KBUILD_STR(s)=#s" -D"KBUILD_BASENAME=KBUILD
   _STR(os_interface)"  -D"KBUILD_MODNAME=KBUILD_STR(nvidia)" -c -o /tmp/selfgz
   6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/.tmp_os-interface.o /tmp/sel
   fgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/os-interface.c
   In file included from include/linux/bitops.h:17,
                    from include/linux/kernel.h:15,
                    from include/linux/sched.h:52,
                    from include/linux/utsname.h:35,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:19,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/os-interface.c:26:
   include/asm/bitops.h: In function ‘set_bit’:
   include/asm/bitops.h:60: warning: pointer of type ‘void *’ used in arith
   metic
   include/asm/bitops.h: In function ‘clear_bit’:
   include/asm/bitops.h:97: warning: pointer of type ‘void *’ used in arith
   metic
   In file included from include/linux/list.h:6,
                    from include/linux/preempt.h:11,
                    from include/linux/spinlock.h:50,
                    from include/linux/seqlock.h:29,
                    from include/linux/time.h:8,
                    from include/linux/timex.h:57,
                    from include/linux/sched.h:54,
                    from include/linux/utsname.h:35,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:19,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/os-interface.c:26:
   include/linux/prefetch.h: In function ‘prefetch_range’:
   include/linux/prefetch.h:57: warning: pointer of type ‘void *’ used in a
   rithmetic
   In file included from include/linux/utsname.h:35,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:19,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/os-interface.c:26:
   include/linux/sched.h: In function ‘object_is_on_stack’:
   include/linux/sched.h:1975: warning: pointer of type ‘void *’ used in ar
   ithmetic
   In file included from include/asm/dma-mapping.h:9,
                    from include/linux/dma-mapping.h:52,
                    from include/asm-generic/pci-dma-compat.h:7,
                    from include/asm/pci.h:94,
                    from include/linux/pci.h:989,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:86,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/os-interface.c:26:
   include/linux/scatterlist.h: In function ‘sg_virt’:
   include/linux/scatterlist.h:199: warning: pointer of type ‘void *’ used 
   in arithmetic
   In file included from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:113,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/os-interface.c:26:
   include/linux/highmem.h: In function ‘zero_user_segments’:
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
     cc -Wp,-MD,/tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/.os-
   registry.o.d  -nostdinc -isystem /usr/lib/gcc/i486-linux-gnu/4.3.2/include -
   D__KERNEL__  -Iinclude  -I/usr/src/linux-headers-2.6.27-11-generic/arch/x86/
   include -include include/linux/autoconf.h -Iubuntu/include  -Wall -Wundef -W
   strict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -Werror-im
   plicit-function-declaration -O2 -m32 -msoft-float -mregparm=3 -freg-struct-r
   eturn -mpreferred-stack-boundary=2 -march=i586 -mtune=generic -ffreestanding
   -pipe -Wno-sign-compare -fno-asynchronous-unwind-tables -mno-sse -mno-mmx -m
   no-sse2 -mno-3dnow -Iinclude/asm-x86/mach-default -fno-stack-protector -fno-
   omit-frame-pointer -fno-optimize-sibling-calls -pg -Wdeclaration-after-state
   ment -Wno-pointer-sign -I/tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr
   /src/nv -Wall -Wimplicit -Wreturn-type -Wswitch -Wformat -Wchar-subscripts -
   Wparentheses -Wpointer-arith -Wno-multichar -Werror -MD -Wsign-compare -Wno-
   cast-qual -Wno-error -D__KERNEL__ -DMODULE -DNVRM -DNV_VERSION_STRING=\"173.
   14.18\" -UDEBUG -U_DEBUG -DNDEBUG -DMODULE -D"KBUILD_
   STR(s)=#s" -D"KBUILD_BASENAME=KBUILD_STR(os_registry)"  -D"KBUILD_MODNAME=KB
   UILD_STR(nvidia)" -c -o /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/
   src/nv/.tmp_os-registry.o /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/us
   r/src/nv/os-registry.c
   In file included from include/linux/bitops.h:17,
                    from include/linux/kernel.h:15,
                    from include/linux/sched.h:52,
                    from include/linux/utsname.h:35,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:19,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/os-registry.c:15:
   include/asm/bitops.h: In function ‘set_bit’:
   include/asm/bitops.h:60: warning: pointer of type ‘void *’ used in arith
   metic
   include/asm/bitops.h: In function ‘clear_bit’:
   include/asm/bitops.h:97: warning: pointer of type ‘void *’ used in arith
   metic
   In file included from include/linux/list.h:6,
                    from include/linux/preempt.h:11,
                    from include/linux/spinlock.h:50,
                    from include/linux/seqlock.h:29,
                    from include/linux/time.h:8,
                    from include/linux/timex.h:57,
                    from include/linux/sched.h:54,
                    from include/linux/utsname.h:35,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:19,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/os-registry.c:15:
   include/linux/prefetch.h: In function ‘prefetch_range’:
   include/linux/prefetch.h:57: warning: pointer of type ‘void *’ used in a
   rithmetic
   In file included from include/linux/utsname.h:35,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:19,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/os-registry.c:15:
   include/linux/sched.h: In function ‘object_is_on_stack’:
   include/linux/sched.h:1975: warning: pointer of type ‘void *’ used in ar
   ithmetic
   In file included from include/asm/dma-mapping.h:9,
                    from include/linux/dma-mapping.h:52,
                    from include/asm-generic/pci-dma-compat.h:7,
                    from include/asm/pci.h:94,
                    from include/linux/pci.h:989,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:86,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/os-registry.c:15:
   include/linux/scatterlist.h: In function ‘sg_virt’:
   include/linux/scatterlist.h:199: warning: pointer of type ‘void *’ used 
   in arithmetic
   In file included from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:113,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/os-registry.c:15:
   include/linux/highmem.h: In function ‘zero_user_segments’:
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
     cc -Wp,-MD,/tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/.nv-
   i2c.o.d  -nostdinc -isystem /usr/lib/gcc/i486-linux-gnu/4.3.2/include -D__KE
   RNEL__  -Iinclude  -I/usr/src/linux-headers-2.6.27-11-generic/arch/x86/inclu
   de -include include/linux/autoconf.h -Iubuntu/include  -Wall -Wundef -Wstric
   t-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -Werror-implici
   t-function-declaration -O2 -m32 -msoft-float -mregparm=3 -freg-struct-return
   -mpreferred-stack-boundary=2 -march=i586 -mtune=generic -ffreestan
   ding -pipe -Wno-sign-compare -fno-asynchronous-unwind-tables -mno-sse -mno-m
   mx -mno-sse2 -mno-3dnow -Iinclude/asm-x86/mach-default -fno-stack-protector 
   -fno-omit-frame-pointer -fno-optimize-sibling-calls -pg -Wdeclaration-after-
   statement -Wno-pointer-sign -I/tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg
   1/usr/src/nv -Wall -Wimplicit -Wreturn-type -Wswitch -Wformat -Wchar-subscri
   pts -Wparentheses -Wpointer-arith -Wno-multichar -Werror -MD -Wsign-compare 
   -Wno-cast-qual -Wno-error -D__KERNEL__ -DMODULE -DNVRM -DNV_VERSION_STRING=\
   "173.14.18\" -UDEBUG -U_DEBUG -DNDEBUG -DMODULE -D"KBUILD_STR(s)=#s" -D"KBUI
   LD_BASENAME=KBUILD_STR(nv_i2c)"  -D"KBUILD_MODNAME=KBUILD_STR(nvidia)" -c -o
   /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/.tmp_nv-i2c.o /tm
   p/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/nv-i2c.c
   In file included from include/linux/bitops.h:17,
                    from include/linux/kernel.h:15,
                    from include/linux/sched.h:52,
                    from include/linux/utsname.h:35,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:19,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-i2c.c:8:
   include/asm/bitops.h: In function ‘set_bit’:
   include/asm/bitops.h:60: warning: pointer of type ‘void *’ used in arith
   metic
   include/asm/bitops.h: In function ‘clear_bit’:
   include/asm/bitops.h:97: warning: pointer of type ‘void *’ used in arith
   metic
   In file included from include/linux/list.h:6,
                    from include/linux/preempt.h:11,
                    from include/linux/spinlock.h:50,
                    from include/linux/seqlock.h:29,
                    from include/linux/time.h:8,
                    from include/linux/timex.h:57,
                    from include/linux/sched.h:54,
                    from include/linux/utsname.h:35,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:19,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-i2c.c:8:
   include/linux/prefetch.h: In function ‘prefetch_range’:
   include/linux/prefetch.h:57: warning: pointer of type ‘void *’ used in a
   rithmetic
   In file included from include/linux/utsname.h:35,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:19,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-i2c.c:8:
   include/linux/sched.h: In function ‘object_is_on_stack’:
   include/linux/sched.h:1975: warning: pointer of type ‘void *’ used in ar
   ithmetic
   In file included from include/asm/dma-mapping.h:9,
                    from include/linux/dma-mapping.h:52,
                    from include/asm-generic/pci-dma-compat.h:7,
                    from include/asm/pci.h:94,
                    from include/linux/pci.h:989,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:86,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-i2c.c:8:
   include/linux/scatterlist.h: In function ‘sg_virt’:
   include/linux/scatterlist.h:199: warning: pointer of type ‘void *’ used 
   in arithmetic
   In file included from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:113,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-i2c.c:8:
   include/linux/highmem.h: In function ‘zero_user_segments’:
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
     cc -Wp,-MD,/tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/.nva
   cpi.o.d  -nostdinc -isystem /usr/lib/gcc/i486-linux-gnu/4.3.2/include -D__KE
   RNEL__  -Iinclude  -I/usr/src/linux-headers-2.6.27-11-generic/arch/x86/inclu
   de -include include/linux/autoconf.h -Iubuntu/include  -Wall -Wundef -Wstric
   t-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -Werror-implici
   t-function-declaration -O2 -m32 -msoft-float -mregparm=3 -freg-struct-return
   -mpreferred-stack-boundary=2 -march=i586 -mtune=generic -ffreestanding -pipe
   -Wno-sign-compare -fno-asynchronous-unwind-tables -mno-sse -mno-mmx -mno-sse
   2 -mno-3dnow -Iinclude/asm-x86/mach-default -fno-stack-protector -fno-omit-f
   rame-pointer -fno-optimize-sibling-calls -pg -Wdeclaration-after-statement -
   Wno-pointer-sign -I/tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/n
   v -Wall -Wimplicit -Wreturn-type -Wswitch -Wformat -Wchar-subscripts -Wparen
   theses -Wpointer-arith -Wno-multichar -Werror -MD -Wsign-compare -Wno-cast-q
   ual -Wno-err
   or -D__KERNEL__ -DMODULE -DNVRM -DNV_VERSION_STRING=\"173.14.18\" -UDEBUG -U
   _DEBUG -DNDEBUG -DMODULE -D"KBUILD_STR(s)=#s" -D"KBUILD_BASENAME=KBUILD_STR(
   nvacpi)"  -D"KBUILD_MODNAME=KBUILD_STR(nvidia)" -c -o /tmp/selfgz6317/NVIDIA
   -Linux-x86-173.14.18-pkg1/usr/src/nv/.tmp_nvacpi.o /tmp/selfgz6317/NVIDIA-Li
   nux-x86-173.14.18-pkg1/usr/src/nv/nvacpi.c
   In file included from include/linux/bitops.h:17,
                    from include/linux/kernel.h:15,
                    from include/linux/sched.h:52,
                    from include/linux/utsname.h:35,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:19,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nvacpi.c:15:
   include/asm/bitops.h: In function ‘set_bit’:
   include/asm/bitops.h:60: warning: pointer of type ‘void *’ used in arith
   metic
   include/asm/bitops.h: In function ‘clear_bit’:
   include/asm/bitops.h:97: warning: pointer of type ‘void *’ used in arith
   metic
   In file included from include/linux/list.h:6,
                    from include/linux/preempt.h:11,
                    from include/linux/spinlock.h:50,
                    from include/linux/seqlock.h:29,
                    from include/linux/time.h:8,
                    from include/linux/timex.h:57,
                    from include/linux/sched.h:54,
                    from include/linux/utsname.h:35,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:19,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nvacpi.c:15:
   include/linux/prefetch.h: In function ‘prefetch_range’:
   include/linux/prefetch.h:57: warning: pointer of type ‘void *’ used in a
   rithmetic
   In file included from include/linux/utsname.h:35,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:19,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nvacpi.c:15:
   include/linux/sched.h: In function ‘object_is_on_stack’:
   include/linux/sched.h:1975: warning: pointer of type ‘void *’ used in ar
   ithmetic
   In file included from include/asm/dma-mapping.h:9,
                    from include/linux/dma-mapping.h:52,
                    from include/asm-generic/pci-dma-compat.h:7,
                    from include/asm/pci.h:94,
                    from include/linux/pci.h:989,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:86,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nvacpi.c:15:
   include/linux/scatterlist.h: In function ‘sg_virt’:
   include/linux/scatterlist.h:199: warning: pointer of type ‘void *’ used 
   in arithmetic
   In file included from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nv-linux.h:113,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nvacpi.c:15:
   include/linux/highmem.h: In function ‘zero_user_segments’:
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:134: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
   include/linux/highmem.h:137: warning: pointer of type ‘void *’ used in a
   rithmetic
     ld -m elf_i386   -r -o /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr
   /src/nv/nvidia.o /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/
   nv-kernel.o /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/nv.o 
   /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/nv-vm.o /tmp/self
   gz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/os-agp.o /tmp/selfgz6317/N
   VIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/os-interface.o /tmp/selfgz6317
   /NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/os-registry.o /tmp/selfgz6317/NV
   IDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/nv-i2c.o /tmp/selfgz6317/NVIDIA-Lin
   ux-x86-173.14.18-pkg1/usr/src/nv/nvacpi.o 
   (cat /dev/null;   echo kernel//tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg
   1/usr/src/nv/nvidia.ko;) > /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/u
   sr/src/nv/modules.order
     Building modules, stage 2.
   make -f /usr/src/linux-headers-2.6.27-11-generic/scripts/Makefile.modpost
     scripts/mod/modpost -m -a -i /usr/src/linux-headers-2.6.27-11-generic/Modu
   le.symvers -I /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/Mod
   ule.symvers  -o /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/M
   odule.symvers -S -K /usr/src/linux-headers-2.6.27-11-generic/Module.markers 
   -M /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/Module.markers
   -w  -s
   WARNING: could not find /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/
   src/nv/.nv-kernel.o.cmd for /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/
   usr/src/nv/nv-kernel.o
     cc -Wp,-MD,/tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/nv/.nvi
   dia.mod.o.d  -nostdinc -isystem /usr/lib/gcc/i486-linux-gnu/4.3.2/include -D
   __KERNEL__  -Iinclude  -I/usr/src/linux-headers-2.6.27-11-generic/arch/x86/i
   nclude -include include/linux/autoconf.h -Iubuntu/include  -Wall -Wundef -Ws
   trict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -Werror-imp
   licit-function-declaration -O2 -m32 -msoft-float -mregparm=3 -freg-struct-re
   turn -mpreferred-stack-boundary=2 -march=i586 -mtune=generic -ffreestanding 
   -pipe -Wno-sign-compare -fno-asynchronous-unwind-tables -mno-sse -mno-mmx -m
   no-sse2 -mno-3dnow -Iinclude/asm-x86/mach-default -fno-stack-protector -fno-
   omit-frame-pointer -fno-optimize-sibling-calls -pg -Wdeclaration-after-state
   ment -Wno-pointer-sign -I/tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr
   /src/nv -Wall -Wimplicit -Wreturn-type -Wswitch -Wformat -Wchar-subscripts -
   Wparentheses -Wpointer-arith -Wno-multichar -Werror -MD -Wsign-compare -Wno-
   cast-qual -Wno-error -D
   __KERNEL__ -DMODULE -DNVRM -DNV_VERSION_STRING=\"173.14.18\" -UDEBUG -U_DEBU
   G -DNDEBUG  -D"KBUILD_STR(s)=#s" -D"KBUILD_BASENAME=KBUILD_STR(nvidia.mod)" 
   -D"KBUILD_MODNAME=KBUILD_STR(nvidia)" -DMODULE -c -o /tmp/selfgz6317/NVIDIA-
   Linux-x86-173.14.18-pkg1/usr/src/nv/nvidia.mod.o /tmp/selfgz6317/NVIDIA-Linu
   x-x86-173.14.18-pkg1/usr/src/nv/nvidia.mod.c
   In file included from include/linux/bitops.h:17,
                    from include/asm/cpufeature.h:123,
                    from include/asm/processor.h:16,
                    from include/linux/prefetch.h:14,
                    from include/linux/list.h:6,
                    from include/linux/module.h:9,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nvidia.mod.c:1:
   include/asm/bitops.h: In function ‘set_bit’:
   include/asm/bitops.h:60: warning: pointer of type ‘void *’ used in arith
   metic
   include/asm/bitops.h: In function ‘clear_bit’:
   include/asm/bitops.h:97: warning: pointer of type ‘void *’ used in arith
   metic
   In file included from include/linux/list.h:6,
                    from include/linux/module.h:9,
                    from /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/sr
   c/nv/nvidia.mod.c:1:
   include/linux/prefetch.h: In function ‘prefetch_range’:
   include/linux/prefetch.h:57: warning: pointer of type ‘void *’ used in a
   rithmetic
     ld -r -m elf_i386  --build-id -o /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.1
   8-pkg1/usr/src/nv/nvidia.ko /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/
   usr/src/nv/nvidia.o /tmp/selfgz6317/NVIDIA-Linux-x86-173.14.18-pkg1/usr/src/
   nv/nvidia.mod.o
   NVIDIA: left KBUILD.
-> done.
-> Kernel module compilation complete.
-> Kernel messages:
   [   34.629404] agpgart-amd64 0000:00:00.0: AGP 3.0 bridge
   [   34.629424] agpgart-amd64 0000:00:00.0: putting AGP V3 device into 8x
   mode
   [   34.629489] nvidia 0000:01:00.0: putting AGP V3 device into 8x mode
   [   38.269246] agpgart-amd64 0000:00:00.0: AGP 3.0 bridge
   [   38.269268] agpgart-amd64 0000:00:00.0: putting AGP V3 device into 8x
   mode
   [   38.269336] nvidia 0000:01:00.0: putting AGP V3 device into 8x mode
   [   41.896890] agpgart-amd64 0000:00:00.0: AGP 3.0 bridge
   [   41.896912] agpgart-amd64 0000:00:00.0: putting AGP V3 device into 8x
   mode
   [   41.896978] nvidia 0000:01:00.0: putting AGP V3 device into 8x mode
   [  131.192886] wlan0: authenticate with AP 00:1c:a2:6c:17:af
   [  131.194630] wlan0: authenticated
   [  131.194635] wlan0: associate with AP 00:1c:a2:6c:17:af
   [  131.196929] wlan0: RX AssocResp from 00:1c:a2:6c:17:af (capab=0x11
   status=0 aid=4)
   [  131.196933] wlan0: associated
   [  141.491054] NET: Registered protocol family 10
   [  141.493102] lo: Disabled Privacy Extensions
   [  141.494100] ADDRCONF(NETDEV_UP): eth0: link is not ready
   [  151.648008] wlan0: no IPv6 routers present
   [  195.055730] ppdev0: registered pardevice
   [  195.104015] ppdev0: unregistered pardevice
   [  196.504158] ppdev0: registered pardevice
   [  196.552224] ppdev0: unregistered pardevice
   [  198.208301] ppdev0: registered pardevice
   [  198.256139] ppdev0: unregistered pardevice
   [  508.276737] NVRM: loading NVIDIA UNIX x86 Kernel Module  173.14.18  Mon
   Mar  2 12:17:40 PST 2009
-> Installing both new and classic TLS OpenGL libraries.
-> Searching for conflicting X files:
-> done.
-> Searching for conflicting OpenGL files:
-> done.
-> Installing 'NVIDIA Accelerated Graphics Driver for Linux-x86' (173.14.18):
   executing: '/sbin/ldconfig'...
   executing: '/sbin/depmod -aq'...
-> done.
-> Driver file installation is complete.
-> Running post-install sanity check:
-> done.
-> Post-install sanity check passed.
-> Shared memory test passed.
-> Running runtime sanity check:
-> done.
-> Runtime sanity check passed.
-> Would you like to run the nvidia-xconfig utility to automatically update you
   r X configuration file so that the NVIDIA X driver will be used when you res
   tart X?  Any pre-existing X configuration file will be backed up. (Answer: Y
   es)
-> Your X configuration file has been successfully updated.  Installation of
   the NVIDIA Accelerated Graphics Driver for Linux-x86 (version: 173.14.18) is
   now complete.
alessia@alessia-laptop:~$ 

eseguito tutto alla lettera
Jack_ut
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 1698
Iscrizione: giovedì 6 novembre 2008, 15:29

Re: driver GeForce FX Go5650

Messaggio da Jack_ut »

La domanda sorge spontanea, è cambiato qualcosa?
I drivers adesso vengono caricati?

Dal log pare che l'installazione sia andata a buon fine... :-\

Fammi sapere
Avatar utente
ilmarchi
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 474
Iscrizione: giovedì 6 novembre 2008, 19:36

Re: driver GeForce FX Go5650

Messaggio da ilmarchi »

no mi dispiace ma si avvia sempre in low graphic mode questo portatile sembra stregato
Jack_ut
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 1698
Iscrizione: giovedì 6 novembre 2008, 15:29

Re: driver GeForce FX Go5650

Messaggio da Jack_ut »

Prova a modificare lo xorg così

Codice: Seleziona tutto

# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig:  version 1.0  (buildmeister@builder63)  Mon Mar  2 12:45:55 PST 2009


Section "ServerLayout"
    Identifier     "Layout0"
    Screen         "Screen0" 0 0
    InputDevice    "Keyboard0" "CoreKeyboard"
    InputDevice    "Mouse0" "CorePointer"
EndSection

Section "Files"
EndSection

Section "Module"
    Load           "dbe"
    Load           "extmod"
    Load           "type1"
    Load           "freetype"
    Load           "glx"
EndSection

Section "InputDevice"

    # generated from default
    Identifier     "Mouse0"
    Driver         "mouse"
    Option         "Protocol" "auto"
    Option         "Device" "/dev/psaux"
    Option         "Emulate3Buttons" "no"
    Option         "ZAxisMapping" "4 5"
EndSection

Section "InputDevice"

    # generated from default
    Identifier     "Keyboard0"
    Driver         "kbd"
    Option         "XkbLayout" "it"
EndSection

Section "Monitor"
    Identifier     "Monitor0"
    VendorName     "Unknown"
    ModelName      "Unknown"
    HorizSync       30.0 - 110.0
    VertRefresh     50.0 - 150.0
    Option         "DPMS"
EndSection

Section "Device"
    Identifier     "Device0"
    Busid          "PCI:1:0:0"
    Driver         "nvidia"
    VendorName     "NVIDIA Corporation"
    BoardName      "GeForce FX Go5650"
EndSection

Section "Screen"
    Identifier     "Screen0"
    Device         "Device0"
    Monitor        "Monitor0"
    DefaultDepth    24
    Option         "AddARGBGLXVisuals" "True"
    Option         "TwinView" "0"
    Option         "metamodes" "1024x768 +0+0"
    SubSection     "Display"
        Depth       24
    EndSubSection
EndSection

Section "Extensions"
    Option         "Composite" "Enable"
EndSection
Riavvia e poi riposta anche il log di Xorg

>:( >:( >:( >:( >:(
Avatar utente
ilmarchi
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 474
Iscrizione: giovedì 6 novembre 2008, 19:36

Re: driver GeForce FX Go5650

Messaggio da ilmarchi »

cosi non me lo fa salvare mi dice che non ho i permessi sufficenti ti allego il mess. di errore
Allegati
Schermata-*xorg.conf (-etc-X11) - gedit.png
Jack_ut
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 1698
Iscrizione: giovedì 6 novembre 2008, 15:29

Re: driver GeForce FX Go5650

Messaggio da Jack_ut »

Ogni volta che devi editare lo xorg.conf, lo devi fare da amministratore, apri un terminale

Codice: Seleziona tutto

sudo gedit /etc/X11/xorg.conf
e modificalo
Avatar utente
ilmarchi
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 474
Iscrizione: giovedì 6 novembre 2008, 19:36

Re: driver GeForce FX Go5650

Messaggio da ilmarchi »

Codice: Seleziona tutto

	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 320
	XResolution: 320
	YResolution: 400
	XCharSize: 8
	YCharSize: 16
	NumberOfPlanes: 1
	BitsPerPixel: 8
	NumberOfBanks: 1
	MemoryModel: 4
	BankSize: 0
	NumberOfImages: 30
	RedMaskSize: 0
	RedFieldPosition: 0
	GreenMaskSize: 0
	GreenFieldPosition: 0
	BlueMaskSize: 0
	BlueFieldPosition: 0
	RsvdMaskSize: 0
	RsvdFieldPosition: 0
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 320
	BnkNumberOfImagePages: 30
	LinNumberOfImagePages: 30
	LinRedMaskSize: 0
	LinRedFieldPosition: 0
	LinGreenMaskSize: 0
	LinGreenFieldPosition: 0
	LinBlueMaskSize: 0
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 0
	LinRsvdFieldPosition: 0
	MaxPixelClock: 229500000
Mode: 132 (320x400)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 640
	XResolution: 320
	YResolution: 400
	XCharSize: 8
	YCharSize: 16
	NumberOfPlanes: 1
	BitsPerPixel: 16
	NumberOfBanks: 1
	MemoryModel: 6
	BankSize: 0
	NumberOfImages: 14
	RedMaskSize: 5
	RedFieldPosition: 11
	GreenMaskSize: 6
	GreenFieldPosition: 5
	BlueMaskSize: 5
	BlueFieldPosition: 0
	RsvdMaskSize: 0
	RsvdFieldPosition: 0
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 640
	BnkNumberOfImagePages: 14
	LinNumberOfImagePages: 14
	LinRedMaskSize: 5
	LinRedFieldPosition: 11
	LinGreenMaskSize: 6
	LinGreenFieldPosition: 5
	LinBlueMaskSize: 5
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 0
	LinRsvdFieldPosition: 0
	MaxPixelClock: 229500000
*Mode: 133 (320x400)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 1280
	XResolution: 320
	YResolution: 400
	XCharSize: 8
	YCharSize: 16
	NumberOfPlanes: 1
	BitsPerPixel: 32
	NumberOfBanks: 1
	MemoryModel: 6
	BankSize: 0
	NumberOfImages: 6
	RedMaskSize: 8
	RedFieldPosition: 16
	GreenMaskSize: 8
	GreenFieldPosition: 8
	BlueMaskSize: 8
	BlueFieldPosition: 0
	RsvdMaskSize: 8
	RsvdFieldPosition: 24
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 1280
	BnkNumberOfImagePages: 6
	LinNumberOfImagePages: 6
	LinRedMaskSize: 8
	LinRedFieldPosition: 16
	LinGreenMaskSize: 8
	LinGreenFieldPosition: 8
	LinBlueMaskSize: 8
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 8
	LinRsvdFieldPosition: 24
	MaxPixelClock: 229500000
Mode: 134 (320x240)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 320
	XResolution: 320
	YResolution: 240
	XCharSize: 8
	YCharSize: 8
	NumberOfPlanes: 1
	BitsPerPixel: 8
	NumberOfBanks: 1
	MemoryModel: 4
	BankSize: 0
	NumberOfImages: 30
	RedMaskSize: 0
	RedFieldPosition: 0
	GreenMaskSize: 0
	GreenFieldPosition: 0
	BlueMaskSize: 0
	BlueFieldPosition: 0
	RsvdMaskSize: 0
	RsvdFieldPosition: 0
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 320
	BnkNumberOfImagePages: 30
	LinNumberOfImagePages: 30
	LinRedMaskSize: 0
	LinRedFieldPosition: 0
	LinGreenMaskSize: 0
	LinGreenFieldPosition: 0
	LinBlueMaskSize: 0
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 0
	LinRsvdFieldPosition: 0
	MaxPixelClock: 229500000
Mode: 135 (320x240)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 640
	XResolution: 320
	YResolution: 240
	XCharSize: 8
	YCharSize: 8
	NumberOfPlanes: 1
	BitsPerPixel: 16
	NumberOfBanks: 1
	MemoryModel: 6
	BankSize: 0
	NumberOfImages: 19
	RedMaskSize: 5
	RedFieldPosition: 11
	GreenMaskSize: 6
	GreenFieldPosition: 5
	BlueMaskSize: 5
	BlueFieldPosition: 0
	RsvdMaskSize: 0
	RsvdFieldPosition: 0
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 640
	BnkNumberOfImagePages: 19
	LinNumberOfImagePages: 19
	LinRedMaskSize: 5
	LinRedFieldPosition: 11
	LinGreenMaskSize: 6
	LinGreenFieldPosition: 5
	LinBlueMaskSize: 5
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 0
	LinRsvdFieldPosition: 0
	MaxPixelClock: 229500000
*Mode: 136 (320x240)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 1280
	XResolution: 320
	YResolution: 240
	XCharSize: 8
	YCharSize: 8
	NumberOfPlanes: 1
	BitsPerPixel: 32
	NumberOfBanks: 1
	MemoryModel: 6
	BankSize: 0
	NumberOfImages: 10
	RedMaskSize: 8
	RedFieldPosition: 16
	GreenMaskSize: 8
	GreenFieldPosition: 8
	BlueMaskSize: 8
	BlueFieldPosition: 0
	RsvdMaskSize: 8
	RsvdFieldPosition: 24
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 1280
	BnkNumberOfImagePages: 10
	LinNumberOfImagePages: 10
	LinRedMaskSize: 8
	LinRedFieldPosition: 16
	LinGreenMaskSize: 8
	LinGreenFieldPosition: 8
	LinBlueMaskSize: 8
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 8
	LinRsvdFieldPosition: 24
	MaxPixelClock: 229500000
Mode: 13d (640x400)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 1280
	XResolution: 640
	YResolution: 400
	XCharSize: 8
	YCharSize: 16
	NumberOfPlanes: 1
	BitsPerPixel: 16
	NumberOfBanks: 1
	MemoryModel: 6
	BankSize: 0
	NumberOfImages: 6
	RedMaskSize: 5
	RedFieldPosition: 11
	GreenMaskSize: 6
	GreenFieldPosition: 5
	BlueMaskSize: 5
	BlueFieldPosition: 0
	RsvdMaskSize: 0
	RsvdFieldPosition: 0
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 1280
	BnkNumberOfImagePages: 6
	LinNumberOfImagePages: 6
	LinRedMaskSize: 5
	LinRedFieldPosition: 11
	LinGreenMaskSize: 6
	LinGreenFieldPosition: 5
	LinBlueMaskSize: 5
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 0
	LinRsvdFieldPosition: 0
	MaxPixelClock: 229500000
*Mode: 13e (640x400)
	ModeAttributes: 0x39f
	WinAAttributes: 0x7
	WinBAttributes: 0x0
	WinGranularity: 64
	WinSize: 64
	WinASegment: 0xa000
	WinBSegment: 0x0
	WinFuncPtr: 0xc000b837
	BytesPerScanline: 2560
	XResolution: 640
	YResolution: 400
	XCharSize: 8
	YCharSize: 16
	NumberOfPlanes: 1
	BitsPerPixel: 32
	NumberOfBanks: 1
	MemoryModel: 6
	BankSize: 0
	NumberOfImages: 2
	RedMaskSize: 8
	RedFieldPosition: 16
	GreenMaskSize: 8
	GreenFieldPosition: 8
	BlueMaskSize: 8
	BlueFieldPosition: 0
	RsvdMaskSize: 8
	RsvdFieldPosition: 24
	DirectColorModeInfo: 0
	PhysBasePtr: 0xd0000000
	LinBytesPerScanLine: 2560
	BnkNumberOfImagePages: 2
	LinNumberOfImagePages: 2
	LinRedMaskSize: 8
	LinRedFieldPosition: 16
	LinGreenMaskSize: 8
	LinGreenFieldPosition: 8
	LinBlueMaskSize: 8
	LinBlueFieldPosition: 0
	LinRsvdMaskSize: 8
	LinRsvdFieldPosition: 24
	MaxPixelClock: 229500000

(II) VESA(0): Total Memory: 1024 64KB banks (65536kB)
(II) VESA(0): Configured Monitor: Using default hsync range of 31.50-37.90 kHz
(II) VESA(0): Configured Monitor: Using default vrefresh range of 50.00-70.00 Hz
(WW) VESA(0): Unable to estimate virtual size
(II) VESA(0): Not using built-in mode "1024x768" (no mode of this name)
(II) VESA(0): Not using built-in mode "800x600" (no mode of this name)
(II) VESA(0): Not using built-in mode "640x480" (no mode of this name)
(II) VESA(0): Not using built-in mode "640x400" (no mode of this name)
(II) VESA(0): Not using built-in mode "320x400" (no mode of this name)
(II) VESA(0): Not using built-in mode "320x240" (no mode of this name)
(II) VESA(0): Not using built-in mode "320x200" (no mode of this name)
(WW) VESA(0): No valid modes left.  Trying less strict filter...
(II) VESA(0): Configured Monitor: Using hsync range of 31.50-37.90 kHz
(II) VESA(0): Configured Monitor: Using vrefresh range of 50.00-70.00 Hz
(WW) VESA(0): Unable to estimate virtual size
(II) VESA(0): Not using built-in mode "1024x768" (hsync out of range)
(II) VESA(0): Not using built-in mode "640x400" (hsync out of range)
(II) VESA(0): Not using built-in mode "320x400" (hsync out of range)
(II) VESA(0): Not using built-in mode "320x240" (illegal horizontal timings)
(II) VESA(0): Not using built-in mode "320x200" (illegal horizontal timings)
(--) VESA(0): Virtual size is 800x600 (pitch 800)
(**) VESA(0): *Built-in mode "800x600"
(**) VESA(0): *Built-in mode "640x480"
(==) VESA(0): DPI set to (96, 96)
(II) VESA(0): Attempting to use 60Hz refresh for mode "800x600" (115)
(II) VESA(0): Attempting to use 60Hz refresh for mode "640x480" (112)
(**) VESA(0): Using "Shadow Framebuffer"
(II) Loading sub module "shadow"
(II) LoadModule: "shadow"

(II) Loading /usr/lib/xorg/modules//libshadow.so
(II) Module shadow: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.1.0
	ABI class: X.Org ANSI C Emulation, version 0.4
(II) Loading sub module "fb"
(II) LoadModule: "fb"

(II) Loading /usr/lib/xorg/modules//libfb.so
(II) Module fb: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 1.0.0
	ABI class: X.Org ANSI C Emulation, version 0.4
(==) Depth 24 pixmap format is 32 bpp
(II) do I need RAC?  No, I don't.
(II) resource ranges after preInit:
	[0] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[1] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[2] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[3] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[4] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[5] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[6] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[7] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[8] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[9] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[10] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[11] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[12] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[13] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[14] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[15] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[16] -1	0	0xffffffff - 0xffffffff (0x1) MX[B]
	[17] -1	0	0x000f0000 - 0x000fffff (0x10000) MX[B]
	[18] -1	0	0x000c0000 - 0x000effff (0x30000) MX[B]
	[19] -1	0	0x00000000 - 0x0009ffff (0xa0000) MX[B]
	[20] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[21] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[22] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[23] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[24] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[25] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[26] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[27] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
	[28] -1	0	0x0000ffff - 0x0000ffff (0x1) IX[B]
	[29] -1	0	0x00000000 - 0x00000000 (0x1) IX[B]
(II) Loading sub module "int10"
(II) LoadModule: "int10"

(II) Reloading /usr/lib/xorg/modules//libint10.so
(II) VESA(0): initializing int10
(II) VESA(0): Primary V_BIOS segment is: 0xc000
(II) VESA(0): VESA BIOS detected
(II) VESA(0): VESA VBE Version 3.0
(II) VESA(0): VESA VBE Total Mem: 65536 kB
(II) VESA(0): VESA VBE OEM: NVIDIA
(II) VESA(0): VESA VBE OEM Software Rev: 4.49
(II) VESA(0): VESA VBE OEM Vendor: NVIDIA Corporation
(II) VESA(0): VESA VBE OEM Product: NV31 Board - e133n   
(II) VESA(0): VESA VBE OEM Product Rev: Chip Rev   
(II) VESA(0): virtual address = 0xb2b94000,
	physical address = 0xd0000000, size = 67108864
(==) VESA(0): Default visual is TrueColor
(==) VESA(0): Backing store disabled
(II) VESA(0): DPMS enabled
(==) RandR enabled
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found)
(II) config/hal: Adding input device Macintosh mouse button emulation
(II) LoadModule: "evdev"

(II) Loading /usr/lib/xorg/modules/input//evdev_drv.so
(II) Module evdev: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 2.0.99
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 2.1
(**) Macintosh mouse button emulation: always reports core events
(**) Macintosh mouse button emulation: Device: "/dev/input/event0"
(II) Macintosh mouse button emulation: Found x and y relative axes
(II) Macintosh mouse button emulation: Found 3 mouse buttons
(II) Macintosh mouse button emulation: Configuring as mouse
(II) XINPUT: Adding extended input device "Macintosh mouse button emulation" (type: MOUSE)
(**) Macintosh mouse button emulation: YAxisMapping: buttons 4 and 5
(**) Macintosh mouse button emulation: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
(II) config/hal: Adding input device SynPS/2 Synaptics TouchPad
(II) LoadModule: "synaptics"

(II) Loading /usr/lib/xorg/modules/input//synaptics_drv.so
(II) Module synaptics: vendor="X.Org Foundation"
	compiled for 1.5.2, module version = 0.15.2
	Module class: X.Org XInput Driver
	ABI class: X.Org XInput driver, version 2.1
(II) Synaptics touchpad driver version 0.15.2
(II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
(II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
(**) Option "Device" "/dev/input/event7"
(--) SynPS/2 Synaptics TouchPad touchpad found
(**) SynPS/2 Synaptics TouchPad: always reports core events
(II) XINPUT: Adding extended input device "SynPS/2 Synaptics TouchPad" (type: TOUCHPAD)
(II) SynPS/2 Synaptics TouchPad: x-axis range 1472 - 5472
(II) SynPS/2 Synaptics TouchPad: y-axis range 1408 - 4448
(--) SynPS/2 Synaptics TouchPad touchpad found
(II) config/hal: Adding input device AT Translated Set 2 keyboard
(**) AT Translated Set 2 keyboard: always reports core events
(**) AT Translated Set 2 keyboard: Device: "/dev/input/event1"
(II) AT Translated Set 2 keyboard: Found keys
(II) AT Translated Set 2 keyboard: Configuring as keyboard
(II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) AT Translated Set 2 keyboard: xkb_rules: "evdev"
(**) Option "xkb_model" "pc105"
(**) AT Translated Set 2 keyboard: xkb_model: "pc105"
(**) Option "xkb_layout" "it"
(**) AT Translated Set 2 keyboard: xkb_layout: "it"
(II) config/hal: Adding input device Video Bus
(**) Video Bus: always reports core events
(**) Video Bus: Device: "/dev/input/event8"
(II) Video Bus: Found keys
(II) Video Bus: Configuring as keyboard
(II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD)
(**) Option "xkb_rules" "evdev"
(**) Video Bus: xkb_rules: "evdev"
(**) Option "xkb_model" "pc105"
(**) Video Bus: xkb_model: "pc105"
(**) Option "xkb_layout" "it"
(**) Video Bus: xkb_layout: "it"
AUDIT: Tue Apr  7 13:13:56 2009: 5285 X: client 4 rejected from local host ( uid=0 gid=0 pid=5304 )
AUDIT: Tue Apr  7 13:14:40 2009: 5285 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=5306 )
AUDIT: Tue Apr  7 13:14:40 2009: 5285 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=5307 )
AUDIT: Tue Apr  7 13:14:40 2009: 5285 X: client 4 rejected from local host ( uid=1000 gid=1000 pid=5308 )
alessia@alessia-laptop:~$ 
eccolo anche se non mi pare sia cambiato niente
Jack_ut
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 1698
Iscrizione: giovedì 6 novembre 2008, 15:29

Re: driver GeForce FX Go5650

Messaggio da Jack_ut »

Infatti è identico, allora prova così

Codice: Seleziona tutto

sudo modprobe nvidia
e dopo ricontrolla il log di Xorg, se è differente postalo, dopo posta anche il risultato di

Codice: Seleziona tutto

dmesg
Avatar utente
ilmarchi
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 474
Iscrizione: giovedì 6 novembre 2008, 19:36

Re: driver GeForce FX Go5650

Messaggio da ilmarchi »

Codice: Seleziona tutto

[    0.483604] PCI: 0000:00:01.1 reg 20 io port: [5000, 503f]
[    0.483609] PCI: 0000:00:01.1 reg 24 io port: [5040, 507f]
[    0.483620] pci 0000:00:01.1: PME# supported from D3hot D3cold
[    0.483625] pci 0000:00:01.1: PME# disabled
[    0.483645] PCI: 0000:00:02.0 reg 10 32bit mmio: [febfb000, febfbfff]
[    0.483666] pci 0000:00:02.0: supports D1
[    0.483668] pci 0000:00:02.0: supports D2
[    0.483670] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.483674] pci 0000:00:02.0: PME# disabled
[    0.483689] PCI: 0000:00:02.1 reg 10 32bit mmio: [febfc000, febfcfff]
[    0.483711] pci 0000:00:02.1: supports D1
[    0.483712] pci 0000:00:02.1: supports D2
[    0.483715] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.483718] pci 0000:00:02.1: PME# disabled
[    0.483738] PCI: 0000:00:02.2 reg 10 32bit mmio: [febfdc00, febfdcff]
[    0.483762] pci 0000:00:02.2: supports D1
[    0.483764] pci 0000:00:02.2: supports D2
[    0.483766] pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot D3cold
[    0.483770] pci 0000:00:02.2: PME# disabled
[    0.483792] PCI: 0000:00:06.0 reg 10 io port: [e400, e4ff]
[    0.483797] PCI: 0000:00:06.0 reg 14 io port: [e080, e0ff]
[    0.483801] PCI: 0000:00:06.0 reg 18 32bit mmio: [febfe000, febfefff]
[    0.483818] pci 0000:00:06.0: supports D1
[    0.483820] pci 0000:00:06.0: supports D2
[    0.483837] PCI: 0000:00:06.1 reg 10 io port: [e800, e8ff]
[    0.483842] PCI: 0000:00:06.1 reg 14 io port: [ec00, ec7f]
[    0.483847] PCI: 0000:00:06.1 reg 18 32bit mmio: [febff000, febfffff]
[    0.483864] pci 0000:00:06.1: PME# supported from D3cold
[    0.483867] pci 0000:00:06.1: PME# disabled
[    0.483896] PCI: 0000:00:08.0 reg 20 io port: [ffa0, ffaf]
[    0.484039] PCI: 0000:02:00.0 reg 10 32bit mmio: [feae8000, feaebfff]
[    0.484046] PCI: 0000:02:00.0 reg 14 io port: [d800, d8ff]
[    0.484065] PCI: 0000:02:00.0 reg 30 32bit mmio: [feac0000, feadffff]
[    0.484078] pci 0000:02:00.0: supports D1
[    0.484080] pci 0000:02:00.0: supports D2
[    0.484082] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.484087] pci 0000:02:00.0: PME# disabled
[    0.484107] PCI: 0000:02:01.0 reg 10 32bit mmio: [fd200000, fd200fff]
[    0.484118] pci 0000:02:01.0: supports D1
[    0.484120] pci 0000:02:01.0: supports D2
[    0.484123] pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.484127] pci 0000:02:01.0: PME# disabled
[    0.484147] PCI: 0000:02:01.1 reg 10 32bit mmio: [fa200000, fa200fff]
[    0.484158] pci 0000:02:01.1: supports D1
[    0.484160] pci 0000:02:01.1: supports D2
[    0.484163] pci 0000:02:01.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.484167] pci 0000:02:01.1: PME# disabled
[    0.484187] PCI: 0000:02:01.2 reg 10 32bit mmio: [feaef000, feaef7ff]
[    0.484219] pci 0000:02:01.2: PME# supported from D0 D3hot D3cold
[    0.484223] pci 0000:02:01.2: PME# disabled
[    0.484243] PCI: 0000:02:01.3 reg 10 32bit mmio: [feaef800, feaef8ff]
[    0.484274] pci 0000:02:01.3: supports D1
[    0.484276] pci 0000:02:01.3: supports D2
[    0.484278] pci 0000:02:01.3: PME# supported from D0 D1 D2 D3hot D3cold
[    0.484283] pci 0000:02:01.3: PME# disabled
[    0.484303] PCI: 0000:02:01.4 reg 10 32bit mmio: [feaefc00, feaefcff]
[    0.484334] pci 0000:02:01.4: supports D1
[    0.484336] pci 0000:02:01.4: supports D2
[    0.484338] pci 0000:02:01.4: PME# supported from D0 D1 D2 D3hot D3cold
[    0.484342] pci 0000:02:01.4: PME# disabled
[    0.484365] PCI: 0000:02:02.0 reg 10 32bit mmio: [feafe000, feafffff]
[    0.484395] pci 0000:02:02.0: supports D1
[    0.484396] pci 0000:02:02.0: supports D2
[    0.484399] pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.484403] pci 0000:02:02.0: PME# disabled
[    0.484433] PCI: bridge 0000:00:0a.0 io port: [b000, dfff]
[    0.484437] PCI: bridge 0000:00:0a.0 32bit mmio: [f8a00000, feafffff]
[    0.484494] PCI: 0000:01:00.0 reg 10 32bit mmio: [f7000000, f7ffffff]
[    0.484501] PCI: 0000:01:00.0 reg 14 32bit mmio: [d0000000, dfffffff]
[    0.484523] PCI: 0000:01:00.0 reg 30 32bit mmio: [f89e0000, f89fffff]
[    0.484574] PCI: bridge 0000:00:0b.0 32bit mmio: [f6900000, f89fffff]
[    0.484579] PCI: bridge 0000:00:0b.0 32bit mmio pref: [c6800000, e67fffff]
[    0.484589] bus 00 -> node 0
[    0.484599] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.484888] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.485110] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[    0.493677] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.493975] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[    0.494272] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[    0.494567] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[    0.494863] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[    0.495158] ACPI: PCI Interrupt Link [LUS0] (IRQs 3 4 5 7 9 10 *11 12 14 15)
[    0.495458] ACPI: PCI Interrupt Link [LUS1] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[    0.495754] ACPI: PCI Interrupt Link [LUS2] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[    0.496055] ACPI: PCI Interrupt Link [LKLN] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.496353] ACPI: PCI Interrupt Link [LAUI] (IRQs 3 4 *5 7 9 10 11 12 14 15)
[    0.496653] ACPI: PCI Interrupt Link [LKMO] (IRQs 3 4 5 7 9 *10 11 12 14 15)
[    0.496952] ACPI: PCI Interrupt Link [LKSM] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.497249] ACPI: PCI Interrupt Link [LTID] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
[    0.497620] ACPI: PCI Interrupt Link [LATA] (IRQs 3 4 6 7 10 11 12 *14 15)
[    0.497803] ACPI: Power Resource [GFAN] (off)
[    0.497864] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 8E, should be 79 [20080609]
[    0.497872] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.497904] pnp: PnP ACPI init
[    0.497911] ACPI: bus type pnp registered
[    0.507485] pnp: PnP ACPI: found 13 devices
[    0.507488] ACPI: ACPI bus type pnp unregistered
[    0.507492] PnPBIOS: Disabled by ACPI PNP
[    0.507839] PCI: Using ACPI for IRQ routing
[    0.507965] NET: Registered protocol family 8
[    0.507965] NET: Registered protocol family 20
[    0.508063] NetLabel: Initializing
[    0.508066] NetLabel:  domain hash size = 128
[    0.508068] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.508084] NetLabel:  unlabeled traffic allowed by default
[    0.508377] tracer: 772 pages allocated for 65536 entries of 48 bytes
[    0.508380]    actual entries 65620
[    0.508584] AppArmor: AppArmor Filesystem Enabled
[    0.508608] ACPI: RTC can wake from S4
[    0.508615] system 00:05: ioport range 0x190-0x193 has been reserved
[    0.508615] system 00:05: ioport range 0x4d0-0x4d1 has been reserved
[    0.508615] system 00:05: ioport range 0xc02-0xc05 has been reserved
[    0.508615] system 00:06: iomem range 0xfec00000-0xfec00fff could not be reserved
[    0.508615] system 00:06: iomem range 0xfee00000-0xfeefffff could not be reserved
[    0.508615] system 00:06: iomem range 0xff780000-0xff7bffff has been reserved
[    0.508615] system 00:0c: iomem range 0x0-0x9ffff could not be reserved
[    0.508615] system 00:0c: iomem range 0xc0000-0xcffff could not be reserved
[    0.508615] system 00:0c: iomem range 0xe0000-0xfffff could not be reserved
[    0.508615] system 00:0c: iomem range 0x100000-0x1fffffff could not be reserved
[    0.508615] system 00:0c: iomem range 0xff7c0000-0xffffffff has been reserved
[    0.543733] pci 0000:02:01.0: BAR 10: can't allocate mem resource [0x0-0x3ffffff]
[    0.543738] pci 0000:02:01.1: BAR 10: can't allocate mem resource [0x0-0x3ffffff]
[    0.543743] pci 0000:02:01.0: CardBus bridge, secondary bus 0000:03
[    0.543745] pci 0000:02:01.0:   IO window: 0x00b000-0x00b0ff
[    0.543750] pci 0000:02:01.0:   IO window: 0x00b400-0x00b4ff
[    0.543754] pci 0000:02:01.0:   PREFETCH window: 0x30000000-0x33ffffff
[    0.543759] pci 0000:02:01.1: CardBus bridge, secondary bus 0000:04
[    0.543762] pci 0000:02:01.1:   IO window: 0x00b800-0x00b8ff
[    0.543766] pci 0000:02:01.1:   IO window: 0x00bc00-0x00bcff
[    0.543770] pci 0000:02:01.1:   PREFETCH window: 0x34000000-0x37ffffff
[    0.543774] pci 0000:00:0a.0: PCI bridge, secondary bus 0000:02
[    0.543778] pci 0000:00:0a.0:   IO window: 0xb000-0xdfff
[    0.543782] pci 0000:00:0a.0:   MEM window: 0xf8a00000-0xfeafffff
[    0.543786] pci 0000:00:0a.0:   PREFETCH window: 0x00000030000000-0x00000037ffffff
[    0.543791] pci 0000:00:0b.0: PCI bridge, secondary bus 0000:01
[    0.543793] pci 0000:00:0b.0:   IO window: disabled
[    0.543798] pci 0000:00:0b.0:   MEM window: 0xf6900000-0xf89fffff
[    0.543803] pci 0000:00:0b.0:   PREFETCH window: 0x000000c6800000-0x000000e67fffff
[    0.543816] pci 0000:00:0a.0: setting latency timer to 64
[    0.544201] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
[    0.544205] PCI: setting IRQ 9 as level-triggered
[    0.544209] pci 0000:02:01.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9
[    0.544567] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
[    0.544570] PCI: setting IRQ 11 as level-triggered
[    0.544574] pci 0000:02:01.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[    0.544584] bus: 00 index 0 io port: [0, ffff]
[    0.544586] bus: 00 index 1 mmio: [0, ffffffff]
[    0.544589] bus: 02 index 0 io port: [b000, dfff]
[    0.544591] bus: 02 index 1 mmio: [f8a00000, feafffff]
[    0.544594] bus: 02 index 2 mmio: [30000000, 37ffffff]
[    0.544596] bus: 02 index 3 mmio: [0, 0]
[    0.544599] bus: 03 index 0 io port: [b000, b0ff]
[    0.544601] bus: 03 index 1 io port: [b400, b4ff]
[    0.544604] bus: 03 index 2 mmio: [30000000, 33ffffff]
[    0.544606] bus: 03 index 3 mmio: [0, 0]
[    0.544608] bus: 04 index 0 io port: [b800, b8ff]
[    0.544611] bus: 04 index 1 io port: [bc00, bcff]
[    0.544613] bus: 04 index 2 mmio: [34000000, 37ffffff]
[    0.544616] bus: 04 index 3 mmio: [0, 0]
[    0.544618] bus: 01 index 0 mmio: [0, 0]
[    0.544620] bus: 01 index 1 mmio: [f6900000, f89fffff]
[    0.544623] bus: 01 index 2 mmio: [c6800000, e67fffff]
[    0.544625] bus: 01 index 3 mmio: [0, 0]
[    0.544637] NET: Registered protocol family 2
[    0.544764] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.544991] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    0.545136] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[    0.545310] TCP: Hash tables configured (established 16384 bind 16384)
[    0.545313] TCP reno registered
[    0.545381] NET: Registered protocol family 1
[    0.545513] checking if image is initramfs... it is
[    1.044078] Switched to high resolution mode on CPU 0
[    1.323950] Freeing initrd memory: 7995k freed
[    1.324785] audit: initializing netlink socket (disabled)
[    1.324804] type=2000 audit(1239128524.324:1): initialized
[    1.331011] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.333538] VFS: Disk quotas dquot_6.5.1
[    1.333626] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.333737] msgmni has been set to 1002
[    1.333864] io scheduler noop registered
[    1.333867] io scheduler anticipatory registered
[    1.333869] io scheduler deadline registered
[    1.333882] io scheduler cfq registered (default)
[    1.376087] pci 0000:01:00.0: Boot video device
[    1.376401] isapnp: Scanning for PnP cards...
[    1.730123] isapnp: No Plug & Play device found
[    1.766838] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.766977] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.767124] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    1.767728] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.768342] ACPI: PCI Interrupt Link [LKMO] enabled at IRQ 10
[    1.768346] PCI: setting IRQ 10 as level-triggered
[    1.768351] serial 0000:00:06.1: PCI INT B -> Link[LKMO] -> GSI 10 (level, low) -> IRQ 10
[    1.768359] serial 0000:00:06.1: PCI INT B disabled
[    1.769926] brd: module loaded
[    1.770006] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[    1.770117] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    1.772700] i8042.c: Detected active multiplexing controller, rev 1.1.
[    1.774243] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.774249] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    1.774252] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    1.774254] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    1.774257] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    1.774805] mice: PS/2 mouse device common for all mice
[    1.774935] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[    1.774957] rtc0: alarms up to one year, y3k
[    1.775069] EISA: Probing bus 0 at eisa.0
[    1.775084] Cannot allocate resource for EISA slot 4
[    1.775087] Cannot allocate resource for EISA slot 5
[    1.775096] EISA: Detected 0 cards.
[    1.775100] cpuidle: using governor ladder
[    1.775103] cpuidle: using governor menu
[    1.775626] TCP cubic registered
[    1.775655] Using IPI No-Shortcut mode
[    1.775846] registered taskstats version 1
[    1.775988]   Magic number: 5:245:392
[    1.776149] acpi PNP0C0D:00: hash matches
[    1.776188] rtc_cmos 00:02: setting system clock to 2009-04-07 18:22:05 UTC (1239128525)
[    1.776192] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    1.776195] EDD information not available.
[    1.776764] Freeing unused kernel memory: 424k freed
[    1.776830] Write protecting the kernel text: 2580k
[    1.776870] Write protecting the kernel read-only data: 940k
[    1.803663] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[    2.032066] fuse init (API version 7.9)
[    2.244249] ACPI: Transitioning device [FN00] to D3
[    2.252011] fan PNP0C0B:00: registered as cooling_device0
[    2.252018] ACPI: Fan [FN00] (off)
[    2.292097] ACPI: Invalid PBLK length [0]
[    2.300012] processor ACPI0007:00: registered as cooling_device1
[    2.344027] thermal LNXTHERM:01: registered as thermal_zone0
[    2.346366] ACPI: Thermal Zone [THRM] (56 C)
[    3.308088] usbcore: registered new interface driver usbfs
[    3.308117] usbcore: registered new interface driver hub
[    3.308156] usbcore: registered new device driver usb
[    3.331572] No dock devices found.
[    3.336851] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 10
[    3.336857] ehci_hcd 0000:00:02.2: PCI INT C -> Link[LUS2] -> GSI 10 (level, low) -> IRQ 10
[    3.336870] ehci_hcd 0000:00:02.2: setting latency timer to 64
[    3.336874] ehci_hcd 0000:00:02.2: EHCI Host Controller
[    3.336928] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
[    3.336964] ehci_hcd 0000:00:02.2: debug port 1
[    3.336969] ehci_hcd 0000:00:02.2: cache line size of 64 is not supported
[    3.336985] ehci_hcd 0000:00:02.2: irq 10, io mem 0xfebfdc00
[    3.337046] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.351791] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[    3.351959] usb usb1: configuration #1 chosen from 1 choice
[    3.351996] hub 1-0:1.0: USB hub found
[    3.352014] hub 1-0:1.0: 6 ports detected
[    3.396438] SCSI subsystem initialized
[    3.456769] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 11
[    3.456777] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 11 (level, low) -> IRQ 11
[    3.456794] ohci_hcd 0000:00:02.0: setting latency timer to 64
[    3.456798] ohci_hcd 0000:00:02.0: OHCI Host Controller
[    3.456826] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[    3.456855] ohci_hcd 0000:00:02.0: irq 11, io mem 0xfebfb000
[    3.508026] libata version 3.00 loaded.
[    3.514196] usb usb2: configuration #1 chosen from 1 choice
[    3.514229] hub 2-0:1.0: USB hub found
[    3.514241] hub 2-0:1.0: 3 ports detected
[    3.616746] ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 5
[    3.616751] PCI: setting IRQ 5 as level-triggered
[    3.616757] ohci_hcd 0000:00:02.1: PCI INT B -> Link[LUS1] -> GSI 5 (level, low) -> IRQ 5
[    3.616776] ohci_hcd 0000:00:02.1: setting latency timer to 64
[    3.616779] ohci_hcd 0000:00:02.1: OHCI Host Controller
[    3.616807] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
[    3.616833] ohci_hcd 0000:00:02.1: irq 5, io mem 0xfebfc000
[    3.674201] usb usb3: configuration #1 chosen from 1 choice
[    3.674239] hub 3-0:1.0: USB hub found
[    3.674253] hub 3-0:1.0: 3 ports detected
[    3.776631] pata_amd 0000:00:08.0: version 0.3.10
[    3.776703] pata_amd 0000:00:08.0: setting latency timer to 64
[    3.776786] scsi0 : pata_amd
[    3.776890] scsi1 : pata_amd
[    3.778862] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    3.778865] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    3.940315] ata1.00: ATAPI: PIONEER DVD-RW DVR-K13AS, 1.11, max UDMA/33
[    3.940337] ata1: nv_mode_filter: 0x739f&0x701f->0x701f, BIOS=0x7000 (0xc000c600) ACPI=0x701f (54:900:0x11)
[    3.956249] ata1.00: configured for UDMA/33
[    4.120949] ata2.00: ATA-6: IC25N040ATMR04-0, MO2OAD4A, max UDMA/100
[    4.120954] ata2.00: 78140160 sectors, multi 16: LBA48 
[    4.120973] ata2: nv_mode_filter: 0x3f39f&0x3f01f->0x3f01f, BIOS=0x3f000 (0xc000c600) ACPI=0x3f01f (17:900:0x11)
[    4.136397] ata2.00: configured for UDMA/100
[    4.143183] scsi 0:0:0:0: CD-ROM            PIONEER  DVD-RW DVR-K13AS 1.11 PQ: 0 ANSI: 5
[    4.143330] scsi 1:0:0:0: Direct-Access     ATA      IC25N040ATMR04-0 MO2O PQ: 0 ANSI: 5
[    4.144304] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[    4.144309] skge 0000:02:00.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[    4.144369] skge 1.13 addr 0xfeae8000 irq 11 chip Yukon-Lite rev 7
[    4.144919] skge eth0: addr 00:0e:a6:e2:72:90
[    4.144962] ohci1394 0000:02:01.2: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[    4.196703] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11]  MMIO=[feaef000-feaef7ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
[    4.205898] b43-pci-bridge 0000:02:02.0: PCI INT A -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
[    4.209250] ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0
[    4.258364] scsi 0:0:0:0: Attached scsi generic sg0 type 5
[    4.258411] scsi 1:0:0:0: Attached scsi generic sg1 type 0
[    4.282119] Driver 'sr' needs updating - please use bus_type methods
[    4.287739] Driver 'sd' needs updating - please use bus_type methods
[    4.300667] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    4.300673] Uniform CD-ROM driver Revision: 3.20
[    4.300784] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    4.300880] sd 1:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
[    4.300896] sd 1:0:0:0: [sda] Write Protect is off
[    4.300899] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.300923] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.300978] sd 1:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
[    4.300992] sd 1:0:0:0: [sda] Write Protect is off
[    4.300995] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    4.301018] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.301022]  sda: sda1 sda2 < sda5 >
[    4.349120] sd 1:0:0:0: [sda] Attached SCSI disk
[    4.655133] PM: Starting manual resume from disk
[    4.655138] PM: Resume from partition 8:5
[    4.655140] PM: Checking hibernation image.
[    4.655283] PM: Resume from disk failed.
[    4.726268] kjournald starting.  Commit interval 5 seconds
[    4.726284] EXT3-fs: mounted filesystem with ordered data mode.
[    5.476139] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00e01800031b04fa]
[   14.643393] udevd version 124 started
[   15.831302] Linux agpgart interface v0.103
[   15.876224] agpgart-amd64 0000:00:00.0: AGP bridge [10de/00d1]
[   15.876262] agpgart-amd64 0000:00:00.0: setting up Nforce3 AGP
[   15.882574] agpgart-amd64 0000:00:00.0: AGP aperture is 128M @ 0xe8000000
[   15.930893] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[   16.119628] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[   16.128016] ACPI: Power Button (FF) [PWRF]
[   16.128127] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input3
[   16.144034] ACPI: Sleep Button (CM) [SLPB]
[   16.144170] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input4
[   16.144303] ACPI: Lid Switch [LID]
[   16.144374] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
[   16.160009] ACPI: Power Button (CM) [PWRB]
[   16.216248] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   16.500212] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x5000
[   16.500220] ACPI: I/O resource nForce2_smbus [0x5040-0x507f] conflicts with ACPI region SMB0 [0x5040-0x507f]
[   16.500224] ACPI: Device needs an ACPI driver
[   16.500293] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x5040
[   16.564171] asus-laptop: Asus Laptop Support version 0.42
[   16.566714] asus-laptop:   L5D model detected
[   16.567313] ACPI: EC: non-query interrupt received, switching to interrupt mode
[   16.569965] Registered led device: asus::mail
[   16.569994] Registered led device: asus::touchpad
[   16.908198] input: PC Speaker as /devices/platform/pcspkr/input/input6
[   17.224434] ACPI: AC Adapter [AC0] (on-line)
[   17.478195] ACPI: Battery Slot [BAT0] (battery present)
[   17.624236] parport_pc 00:0b: reported by Plug and Play ACPI
[   17.624283] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[   17.868601] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:0b/device:0c/input/input7
[   17.880015] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[   18.332619] Yenta: CardBus bridge found at 0000:02:01.0 [1043:1854]
[   18.460379] Yenta: ISA IRQ mask 0x0018, PCI irq 9
[   18.460385] Socket status: 30000006
[   18.460389] pcmcia: parent PCI bridge I/O window: 0xb000 - 0xdfff
[   18.460393] cs: IO port probe 0xb000-0xdfff: clean.
[   18.461020] pcmcia: parent PCI bridge Memory window: 0xf8a00000 - 0xfeafffff
[   18.461024] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x37ffffff
[   18.479568] Yenta: CardBus bridge found at 0000:02:01.1 [1043:1854]
[   18.604354] Yenta: ISA IRQ mask 0x0018, PCI irq 11
[   18.604359] Socket status: 30000006
[   18.604362] Yenta: Raising subordinate bus# of parent bus (#02) from #04 to #07
[   18.604369] pcmcia: parent PCI bridge I/O window: 0xb000 - 0xdfff
[   18.604373] cs: IO port probe 0xb000-0xdfff: clean.
[   18.604986] pcmcia: parent PCI bridge Memory window: 0xf8a00000 - 0xfeafffff
[   18.604990] pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x37ffffff
[   18.678455] ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 5
[   18.678462] Intel ICH 0000:00:06.0: PCI INT A -> Link[LAUI] -> GSI 5 (level, low) -> IRQ 5
[   18.678488] Intel ICH 0000:00:06.0: setting latency timer to 64
[   19.045716] b43-phy0: Broadcom 4306 WLAN found
[   19.094413] phy0: Selected rate control algorithm 'pid'
[   19.264026] intel8x0_measure_ac97_clock: measured 55354 usecs
[   19.264031] intel8x0: clocking to 47446
[   19.286219] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x926eb1, caps: 0x804719/0x0
[   19.299319] Broadcom 43xx driver loaded [ Features: PLR, Firmware-ID: FW13 ]
[   19.323823] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input8
[   21.180833] cs: IO port probe 0x100-0x3af: clean.
[   21.182662] cs: IO port probe 0x3e0-0x4ff: clean.
[   21.183442] cs: IO port probe 0x820-0x8ff: clean.
[   21.185075] cs: IO port probe 0x100-0x3af: clean.
[   21.186897] cs: IO port probe 0x3e0-0x4ff: clean.
[   21.187677] cs: IO port probe 0x820-0x8ff: clean.
[   21.188359] cs: IO port probe 0xc00-0xcf7: clean.
[   21.189192] cs: IO port probe 0xa00-0xaff: clean.
[   21.190039] cs: IO port probe 0xc00-0xcf7: clean.
[   21.190855] cs: IO port probe 0xa00-0xaff: clean.
[   21.612879] lp0: using parport0 (interrupt-driven).
[   21.746428] Adding 1502036k swap on /dev/sda5.  Priority:-1 extents:1 across:1502036k
[   22.390932] EXT3 FS on sda1, internal journal
[   23.498254] type=1505 audit(1239128547.033:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=4008
[   23.733816] type=1505 audit(1239128547.269:3): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=4013
[   23.734125] type=1505 audit(1239128547.269:4): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=4013
[   23.938653] ip_tables: (C) 2000-2006 Netfilter Core Team
[   24.729414] ACPI: WMI: Mapper loaded
[   25.080462] powernow-k8: Found 1 AMD Athlon(tm) 64 Processor 3000+ processors (1 cpu cores) (version 2.20.00)
[   25.087516] powernow-k8: BIOS error - no PSB or ACPI _PSS objects
[   26.011286] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use)
[   26.121856] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[   26.121863] apm: overridden by ACPI.
[   26.304141] ppdev: user-space parallel port driver
[   28.195202] Bluetooth: Core ver 2.13
[   28.195739] NET: Registered protocol family 31
[   28.195743] Bluetooth: HCI device and connection manager initialized
[   28.195747] Bluetooth: HCI socket layer initialized
[   28.219938] Bluetooth: L2CAP ver 2.11
[   28.219944] Bluetooth: L2CAP socket layer initialized
[   28.240323] Bluetooth: SCO (Voice Link) ver 0.6
[   28.240330] Bluetooth: SCO socket layer initialized
[   28.270820] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   28.270826] Bluetooth: BNEP filters: protocol multicast
[   28.340887] Bridge firewalling registered
[   28.370289] Bluetooth: RFCOMM socket layer initialized
[   28.370574] Bluetooth: RFCOMM TTY layer initialized
[   28.370579] Bluetooth: RFCOMM ver 1.10
[   32.492546] skge eth0: enabling interface
[   32.540726] input: b43-phy0 as /devices/virtual/input/input9
[   32.612036] firmware: requesting b43/ucode5.fw
[   32.755471] firmware: requesting b43/pcm5.fw
[   33.043766] firmware: requesting b43/b0g0initvals5.fw
[   33.258897] firmware: requesting b43/b0g0bsinitvals5.fw
[   33.504026] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[   33.655930] Registered led device: b43-phy0::tx
[   33.656235] Registered led device: b43-phy0::rx
[   33.656428] Registered led device: b43-phy0::assoc
[   33.656627] Registered led device: b43-phy0::radio
[   34.055887] nvidia: module license 'NVIDIA' taints kernel.
[   34.317980] NET: Registered protocol family 17
[   34.320041] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11
[   34.320050] nvidia 0000:01:00.0: PCI INT A -> Link[LNKE] -> GSI 11 (level, low) -> IRQ 11
[   34.321714] NVRM: loading NVIDIA UNIX x86 Kernel Module  173.14.18  Mon Mar  2 12:17:40 PST 2009
[   34.558591] agpgart-amd64 0000:00:00.0: AGP 3.0 bridge
[   34.558611] agpgart-amd64 0000:00:00.0: putting AGP V3 device into 8x mode
[   34.558677] nvidia 0000:01:00.0: putting AGP V3 device into 8x mode
[   38.203866] agpgart-amd64 0000:00:00.0: AGP 3.0 bridge
[   38.203888] agpgart-amd64 0000:00:00.0: putting AGP V3 device into 8x mode
[   38.203954] nvidia 0000:01:00.0: putting AGP V3 device into 8x mode
[   41.830563] agpgart-amd64 0000:00:00.0: AGP 3.0 bridge
[   41.830584] agpgart-amd64 0000:00:00.0: putting AGP V3 device into 8x mode
[   41.830651] nvidia 0000:01:00.0: putting AGP V3 device into 8x mode
[  114.496027] wlan0: authenticate with AP 00:1c:a2:6c:17:af
[  114.498520] wlan0: authenticated
[  114.498525] wlan0: associate with AP 00:1c:a2:6c:17:af
[  114.511284] wlan0: RX AssocResp from 00:1c:a2:6c:17:af (capab=0x11 status=0 aid=3)
[  114.511292] wlan0: associated
[  122.544359] NET: Registered protocol family 10
[  122.545346] lo: Disabled Privacy Extensions
[  122.546135] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  132.944009] wlan0: no IPv6 routers present
[  184.922881] ppdev0: registered pardevice
[  184.972016] ppdev0: unregistered pardevice
[  186.403564] ppdev0: registered pardevice
[  186.452298] ppdev0: unregistered pardevice
[  188.804447] ppdev0: registered pardevice
[  188.852148] ppdev0: unregistered pardevice
[  596.489914] glxinfo[5957]: segfault at 0 ip 0804ad46 sp bff0fa10 error 4 in glxinfo[8048000+5000]
alessia@alessia-laptop:~$ 

xorg e uguale il secondo comando eccolo
Jack_ut
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 1698
Iscrizione: giovedì 6 novembre 2008, 15:29

Re: driver GeForce FX Go5650

Messaggio da Jack_ut »

Penso che il tuo problema possa essere relativo a questo

Codice: Seleziona tutto

[  596.489914] glxinfo[5957]: segfault at 0 ip 0804ad46 sp bff0fa10 error 4 in glxinfo[8048000+5000]
Ora come ora l'unico consiglio che a questo punto posso darti è quello di provare con versioni precedenti del driver e vedere se magari riesci a far andare la scheda video. Il 173.14.18 è il driver più recente che supporta la tua scheda, intrepid installa (se non sbaglio) il 173.14.12, prova a scaricare qualche altra versione e prova l'installazione.
Avatar utente
ilmarchi
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 474
Iscrizione: giovedì 6 novembre 2008, 19:36

Re: driver GeForce FX Go5650

Messaggio da ilmarchi »

il .12 è il primo che ho provato a installare è avevo lo stesso problema
mi sa che mi devo rassegnare
Scrivi risposta

Ritorna a “Driver e periferiche”

Chi c’è in linea

Visualizzano questa sezione: 0 utenti iscritti e 4 ospiti