[Driver] hardware: installazione driver matherboard
- mous16
- Imperturbabile Insigne

- Messaggi: 3940
- Iscrizione: mercoledì 25 ottobre 2006, 15:51
- Sesso: Maschile
Re: [Driver] hardware: installazione driver matherboard
cavolo, curioso assai.
Questo comunque fa pensare che la periferica prima venga identificata, e poi per un qualche motivo "scaricata". (forse qualche crash del modulo)
Ora bisognerebbe cercare di capire che chip hai. ci sarebbe da googolare un po' con la stringa che ti da "lspci"
Questo comunque fa pensare che la periferica prima venga identificata, e poi per un qualche motivo "scaricata". (forse qualche crash del modulo)
Ora bisognerebbe cercare di capire che chip hai. ci sarebbe da googolare un po' con la stringa che ti da "lspci"
- kapello
- Entusiasta Emergente

- Messaggi: 2135
- Iscrizione: lunedì 21 maggio 2007, 18:38
- Desktop: KDE
- Distribuzione: Kbuntu 13.10 amd64
- Località: Torino
- Contatti:
Re: [Driver] hardware: installazione driver matherboard
Con l'8.10 non dovresti avere problemi. Con l'8.4 prova questi.
(Non trovavo il link te li ho messi apposta nel mio spazio web)
C'è uno script fatto da me che te li dovrebbe installare automaticamente. Aprilo e leggilo se vuoi capire.
Se ho centrato, così risolvi ... se no, ci ho provato!
link
(Non trovavo il link te li ho messi apposta nel mio spazio web)
C'è uno script fatto da me che te li dovrebbe installare automaticamente. Aprilo e leggilo se vuoi capire.
Se ho centrato, così risolvi ... se no, ci ho provato!
link
Ultima modifica di kapello il venerdì 20 marzo 2009, 2:12, modificato 1 volta in totale.
Quando il saggio indica la luna, lo sciocco guarda il dito - L'esistenza dovrebbe essere sempre colma di bellezza ed emozioni, ma sarebbe ugualmente vuota, senza contenuti. - I miei racconti - Ubuntu user #27862
- kapello
- Entusiasta Emergente

- Messaggi: 2135
- Iscrizione: lunedì 21 maggio 2007, 18:38
- Desktop: KDE
- Distribuzione: Kbuntu 13.10 amd64
- Località: Torino
- Contatti:
Re: [Driver] hardware: installazione driver matherboard
Tutto sbagliato non direi proprio ...Guiodic ha scritto: è tutto sbagliato...
La sua scheda di rete:
Codice: Seleziona tutto
*-network UNCLAIMED
description: Ethernet controller
product: Attansic Technology Corp.
vendor: Attansic Technology Corp.
physical id: 0
bus info: pci@0000:02:00.0
version: b0
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list
Codice: Seleziona tutto
*-network
description: Ethernet interface
product: L1 Gigabit Ethernet Adapter
vendor: Attansic Technology Corp.
physical id: 0
bus info: pci@0000:02:00.0
logical name: eth0
version: b0
serial: 11:14:12:67:32:10
width: 64 bits
clock: 33MHz
capabilities: bus_master cap_list ethernet physical
Ultima modifica di kapello il venerdì 20 marzo 2009, 3:35, modificato 1 volta in totale.
Quando il saggio indica la luna, lo sciocco guarda il dito - L'esistenza dovrebbe essere sempre colma di bellezza ed emozioni, ma sarebbe ugualmente vuota, senza contenuti. - I miei racconti - Ubuntu user #27862
- kapello
- Entusiasta Emergente

- Messaggi: 2135
- Iscrizione: lunedì 21 maggio 2007, 18:38
- Desktop: KDE
- Distribuzione: Kbuntu 13.10 amd64
- Località: Torino
- Contatti:
Re: [Driver] hardware: installazione driver matherboard
Lo script funziona perfettamente. Ripeto, lo usavo io con la 8.04 (non ricordo fino a che kernel), poi, come ho detto dall'inizio, magari alla fine le schede di rete non sono "perfettamente" uguali od il suo problema è un altro. Questo non si può sapere finchè non prova. Resta il fatto che anche io ho una Atheros montata su Asus ed il resoconto di lshw è praticamente lo stesso.
Quando il saggio indica la luna, lo sciocco guarda il dito - L'esistenza dovrebbe essere sempre colma di bellezza ed emozioni, ma sarebbe ugualmente vuota, senza contenuti. - I miei racconti - Ubuntu user #27862
Re: [Driver] hardware: installazione driver matherboard
ru@edubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 10)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation G72 [GeForce 7300 LE] (rev a1)
02:00.0 Ethernet controller: Attansic Technology Corp. Unknown device 1026 (rev b0)
04:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
ru@edubuntu:~$
La scheda ethernet Realtek è quella che sto usando per connettermi; l'altra è quella integrata nella matherboard e dovrebbe essere Atheros e sul cdrom con i driver ci sono i driver linux ma con estensione .tar.bz. Con alien, sarebbe possibile convertirli in .deb ma non capisco come avviare la conversione...
Inoltre, da synaptic ho installato atl2-source linux base driver per Athero fast ethernet adapter...
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 10)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation G72 [GeForce 7300 LE] (rev a1)
02:00.0 Ethernet controller: Attansic Technology Corp. Unknown device 1026 (rev b0)
04:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
ru@edubuntu:~$
La scheda ethernet Realtek è quella che sto usando per connettermi; l'altra è quella integrata nella matherboard e dovrebbe essere Atheros e sul cdrom con i driver ci sono i driver linux ma con estensione .tar.bz. Con alien, sarebbe possibile convertirli in .deb ma non capisco come avviare la conversione...
Inoltre, da synaptic ho installato atl2-source linux base driver per Athero fast ethernet adapter...
Ultima modifica di tapircik il venerdì 20 marzo 2009, 16:14, modificato 1 volta in totale.
- Guiodic
- Accecante Asceta

- Messaggi: 28474
- Iscrizione: martedì 24 aprile 2007, 15:28
- Località: Roma
- Contatti:
Re: [Driver] hardware: installazione driver matherboard
quei driver ci sono già...
comunque si può provare a compilare il driver sul cd.
nel file tar.gz ci dovrebbe essere un README e/o un INSTALL, allegali qui (alien non c'entra)
comunque si può provare a compilare il driver sul cd.
nel file tar.gz ci dovrebbe essere un README e/o un INSTALL, allegali qui (alien non c'entra)
Re: [Driver] hardware: installazione driver matherboard
Codice: Seleziona tutto
Linux* Base Driver for the Atheros(R) AR8121/AR8113 PCI-E Ethernet Adapter
==========================================================================
Contents
========
- In This Release
- Building and Installation
- Command Line Parameters
- Additional Configurations
- Known Issues
- Support
In This Release
===============
This file describes the Linux* Base Driver for the Atheros(R) AR8121/AR8113 PCI-E
Ethernet Adapter, version 1.0.0.5 This driver supports the 2.4.x and 2.6.x kernels.
This driver is only supported as a loadable module at this time. Atheros is not
supplying patches against the kernel source to allow for static linking of
the driver. For questions related to hardware requirements, refer to the
documentation supplied with your Atheros(R) adapter. All hardware
requirements listed apply to use with Linux.
Building and Installation
=========================
To build a binary RPM* package of this driver, run 'rpmbuild -tb
<filename.tar.gz>'. Replace <filename.tar.gz> with the specific filename of
the driver.
NOTE: For the build to work properly, the currently running kernel MUST match
the version and configuration of the installed kernel sources. If you
have just recompiled the kernel reboot the system now.
RPM functionality has only been tested in Red Hat distributions.
1. Move the base driver tar file to the directory of your choice. For example,
use /home/username/arl1e or /usr/local/src/arl1e.
2. Untar/unzip archive:
tar zxf arl1e-x.x.x.x.tar.gz
3. Change to the driver src directory:
cd arl1e-x.x.x.x/src/
4. Compile the driver module:
make install
The binary will be installed as:
/lib/modules/<KERNEL VERSION>/kernel/drivers/net/arl1e.[k]o
The install locations listed above are the default locations. They might
not be correct for certain Linux distributions. For more information,
see the ldistrib.txt file included in the driver tar.
5. Install the module:
insmod arl1e <parameter>=<value>
6. Assign an IP address to the interface by entering the following, where
x is the interface number:
ifconfig ethx <IP_address>
7. Verify that the interface works. Enter the following, where <IP_address>
is the IP address for another machine on the same subnet as the interface
that is being tested:
ping <IP_address>
Command Line Parameters
=======================
If the driver is built as a module, the following optional parameters are
used by entering them on the command line with the modprobe or insmod command
using this syntax:
modprobe arl1e [<option>=<VAL1>,<VAL2>,...]
insmod arl1e [<option>=<VAL1>,<VAL2>,...]
For example, with two L001 PCIE adapters, entering:
insmod arl1e TxMemSize=80,128
loads the arl1e driver with 8KB TX memory for the first adapter and 10KB TX memory
for the second adapter.
The default value for each parameter is generally the recommended setting,
unless otherwise noted.
NOTES: A descriptor describes a data buffer and attributes related to the
data buffer. This information is accessed by the hardware.
MediaType
Valid Range: 0-4
0 - auto-negotiate at all supported speeds
1 - only link at 100Mbps Full Duplex
2 - only link at 100Mbps Half Duplex
3 - only link at 10Mbps Full Duplex
4 - only link at 10Mbps Half Duplex
Default Value: 0
MediaType forces the line speed/duplex to the specified value in
megabits per second(Mbps). If this parameter is not specified or is set
to 0 and the link partner is set to auto-negotiate, the board will
auto-detect the correct speed.
IntModTimer
Valid Range: 50-65000
Default Value: 100
This value represents the minmum interval between interrupts controller
generated.
RxMemBlock
Valid Range: 16-512
Default Value: 64
This value is the number of receice memory block allocated by the driver.
Increasing this value allows the driver to buffer more incoming packets.
Each memory block is 1536 bytes.
NOTE: Depending on the available system resources, the request for a
higher number of receive descriptors may be denied. In this case,
use a lower number.
TxMemSize
Valid Range: 4-64
Default Value: 8
This value is the number KB of transmit memory allocated by the driver.
Increasing this value allows the driver to queue more transmits.
NOTE: Depending on the available system resources, the request for a
higher number of transmit descriptors may be denied. In this case,
use a lower number.
FlashVendor
Valid Range: 0-2
Default Value: 0
This value standards on vendor of spi flash used by the adapter.
0 for Atmel, 1 for SST, 2 for ST
Additional Configurations
=========================
Configuring the Driver on Different Distributions
-------------------------------------------------
Configuring a network driver to load properly when the system is started is
distribution dependent. Typically, the configuration process involves adding
an alias line to /etc/modules.conf as well as editing other system startup
scripts and/or configuration files. Many popular Linux distributions ship
with tools to make these changes for you. To learn the proper way to
configure a network device for your system, refer to your distribution
documentation. If during this process you are asked for the driver or module
name, the name for the Linux Base Driver for the Atheros AR8121/AR8113 is arl1e
As an example, if you install the arl1e driver for two AR8121/AR8113 adapters
(eth0 and eth1) and set the speed and duplex to 10full and 100half, add the
following to modules.conf:
alias eth0 arl1e
alias eth1 arl1e
options arl1e Speed=10,100 Duplex=2,1
Viewing Link Messages
---------------------
Link messages will not be displayed to the console if the distribution is
restricting system messages. In order to see network driver link messages
on your console, set dmesg to eight by entering the following:
dmesg -n 8
NOTE: This setting is not saved across reboots.
Known Issues
============
NOTE: For distribution-specific information, see the ldistrib.txt file
included in the driver tar.
Driver Compilation
------------------
When trying to compile the driver by running make install, the following
error may occur:
"Linux kernel source not configured - missing version.h"
To solve this issue, create the version.h file by going to the Linux source
tree and entering:
make include/linux/version.h.
Support
=======
For general information, go to the Atheros support website at:
http://support.atheros.com
If an issue is identified with the released source code on the supported
kernel with a supported adapter, email the specific information related to
the issue to xiong.huang@atheros.com
License
=======
This software program is released under the terms of a license agreement
between you ('Licensee') and Atheros. Do not use or load this software or any
associated materials (collectively, the 'Software') until you have carefully
read the full terms and conditions of the LICENSE located in this software
package. By loading or using the Software, you agree to the terms of this
Agreement. If you do not agree with the terms of this Agreement, do not
install or use the Software.
* Other names and brands may be claimed as the property of others.
aggiunti i tag code
Ultima modifica di Anonymous il lunedì 23 marzo 2009, 21:06, modificato 1 volta in totale.
- kapello
- Entusiasta Emergente

- Messaggi: 2135
- Iscrizione: lunedì 21 maggio 2007, 18:38
- Desktop: KDE
- Distribuzione: Kbuntu 13.10 amd64
- Località: Torino
- Contatti:
Re: [Driver] hardware: installazione driver matherboard
Mamma mia modifica il post, metti tra tag code!
Quando il saggio indica la luna, lo sciocco guarda il dito - L'esistenza dovrebbe essere sempre colma di bellezza ed emozioni, ma sarebbe ugualmente vuota, senza contenuti. - I miei racconti - Ubuntu user #27862
- Guiodic
- Accecante Asceta

- Messaggi: 28474
- Iscrizione: martedì 24 aprile 2007, 15:28
- Località: Roma
- Contatti:
Re: [Driver] hardware: installazione driver matherboard
mmm questi arl1e non esistono nel kernel di Ubuntu o forse si chiamano diversamente.
Comunque dovrebbero essere compatibili.
Allegami il file tar.bz.qui sul forum, se non entra mandamelo per email a guido.iodice (chiocciola) gmail (punto) com.
Dai
e copia cosa esce
Comunque dovrebbero essere compatibili.
Allegami il file tar.bz.qui sul forum, se non entra mandamelo per email a guido.iodice (chiocciola) gmail (punto) com.
Dai
Codice: Seleziona tutto
uname -rRe: [Driver] hardware: installazione driver matherboard
Ecco il risultato: 2.6.24-23-386
Ti ho spedito i file alla email indicata. Esistono i virus per ubuntu?
Ti ho spedito i file alla email indicata. Esistono i virus per ubuntu?
Re: [Driver] hardware: installazione driver matherboard
Non saprei che dirti...Perchè quale kernel dovrei avere?
- Guiodic
- Accecante Asceta

- Messaggi: 28474
- Iscrizione: martedì 24 aprile 2007, 15:28
- Località: Roma
- Contatti:
Re: [Driver] hardware: installazione driver matherboard
il generic.tapircik ha scritto: Non saprei che dirti...Perchè quale kernel dovrei avere?
che processore hai?
Re: [Driver] hardware: installazione driver matherboard
-cpu:0
description: CPU
product: Intel(R) Pentium(R) D CPU 2.80GHz
vendor: Intel Corp.
physical id: 4
bus info: cpu@0
version: 15.6.4
serial: 0000-0F64-0000-0000-0000-0000
slot: Socket 775
size: 2800MHz
capacity: 3800MHz
width: 64 bits
clock: 200MHz
capabilities: boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx x86-64 constant_tsc pebs bts pni monitor ds_cpl est cid cx16 xtpr lahf_lm cpufreq
configuration: id=0
ti allego la lista hardware
description: CPU
product: Intel(R) Pentium(R) D CPU 2.80GHz
vendor: Intel Corp.
physical id: 4
bus info: cpu@0
version: 15.6.4
serial: 0000-0F64-0000-0000-0000-0000
slot: Socket 775
size: 2800MHz
capacity: 3800MHz
width: 64 bits
clock: 200MHz
capabilities: boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx x86-64 constant_tsc pebs bts pni monitor ds_cpl est cid cx16 xtpr lahf_lm cpufreq
configuration: id=0
ti allego la lista hardware
- Allegati
-
lshw.txt- (14.33 KiB) Scaricato 14 volte
Ultima modifica di tapircik il sabato 21 marzo 2009, 10:06, modificato 1 volta in totale.
- Guiodic
- Accecante Asceta

- Messaggi: 28474
- Iscrizione: martedì 24 aprile 2007, 15:28
- Località: Roma
- Contatti:
Re: [Driver] hardware: installazione driver matherboard
il generic dovrebbe andare benissimo..
installa il pacchetto linux-generic e disinstalla linux-image-2.6.24-23-386 nonchè ogni altro linux-image-numeroversione-386
installa il pacchetto linux-generic e disinstalla linux-image-2.6.24-23-386 nonchè ogni altro linux-image-numeroversione-386
Re: [Driver] hardware: installazione driver matherboard
devo farlo con synaptic?
Re: [Driver] hardware: installazione driver matherboard
Ho fatto e non si riavvia più: posso solo avviare come terminale :'(
Chi c’è in linea
Visualizzano questa sezione: Bing [Bot] e 7 ospiti