[Driver] hardware: installazione driver matherboard

Riconoscimento, installazione e configurazione delle periferiche.
Avatar utente
mous16
Imperturbabile Insigne
Imperturbabile Insigne
Messaggi: 3940
Iscrizione: mercoledì 25 ottobre 2006, 15:51
Sesso: Maschile

Re: [Driver] hardware: installazione driver matherboard

Messaggio da mous16 »

cavolo, curioso assai.
Questo comunque fa pensare che la periferica prima venga identificata, e poi per un qualche motivo "scaricata". (forse qualche crash del modulo)
Ora bisognerebbe cercare di capire che chip hai. ci sarebbe da googolare un po' con la stringa che ti da "lspci"
Pagine personali: Forum Ubuntu-it - Wiki Ubuntu-it - Launchpad
Solo/mous16
Avatar utente
kapello
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 2135
Iscrizione: lunedì 21 maggio 2007, 18:38
Desktop: KDE
Distribuzione: Kbuntu 13.10 amd64
Località: Torino
Contatti:

Re: [Driver] hardware: installazione driver matherboard

Messaggio da kapello »

Con l'8.10 non dovresti avere problemi. Con l'8.4 prova questi.
(Non trovavo il link te li ho messi apposta nel mio spazio web)
C'è uno script fatto da me che te li dovrebbe installare automaticamente. Aprilo e leggilo se vuoi capire.
Se ho centrato, così risolvi ... se no, ci ho provato!

link
Ultima modifica di kapello il venerdì 20 marzo 2009, 2:12, modificato 1 volta in totale.
Quando il saggio indica la luna, lo sciocco guarda il dito - L'esistenza dovrebbe essere sempre colma di bellezza ed emozioni, ma sarebbe ugualmente vuota, senza contenuti. - I miei racconti - Ubuntu user #27862
Avatar utente
kapello
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 2135
Iscrizione: lunedì 21 maggio 2007, 18:38
Desktop: KDE
Distribuzione: Kbuntu 13.10 amd64
Località: Torino
Contatti:

Re: [Driver] hardware: installazione driver matherboard

Messaggio da kapello »

Guiodic ha scritto: è tutto sbagliato...
Tutto sbagliato non direi proprio ...
La sua scheda di rete:

Codice: Seleziona tutto

           *-network UNCLAIMED
                description: Ethernet controller
                product: Attansic Technology Corp.
                vendor: Attansic Technology Corp.
                physical id: 0
                bus info: pci@0000:02:00.0
                version: b0
                width: 64 bits
                clock: 33MHz
                capabilities: pm msi pciexpress bus_master cap_list
  
La mia scheda di rete

Codice: Seleziona tutto

           *-network
                description: Ethernet interface
                product: L1 Gigabit Ethernet Adapter
                vendor: Attansic Technology Corp.
                physical id: 0
                bus info: pci@0000:02:00.0
                logical name: eth0
                version: b0
                serial: 11:14:12:67:32:10
                width: 64 bits
                clock: 33MHz
                capabilities: bus_master cap_list ethernet physical
Direi che sono uguali ... Il sistema è testato e funzionante sulla mia, il kernel della 8.04 non ha i drivers ed ai tempi mi sbattei e risolsi così. Eseguendo lo script come amministratore. Va in rete anche da live (8.04)
Ultima modifica di kapello il venerdì 20 marzo 2009, 3:35, modificato 1 volta in totale.
Quando il saggio indica la luna, lo sciocco guarda il dito - L'esistenza dovrebbe essere sempre colma di bellezza ed emozioni, ma sarebbe ugualmente vuota, senza contenuti. - I miei racconti - Ubuntu user #27862
Avatar utente
kapello
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 2135
Iscrizione: lunedì 21 maggio 2007, 18:38
Desktop: KDE
Distribuzione: Kbuntu 13.10 amd64
Località: Torino
Contatti:

Re: [Driver] hardware: installazione driver matherboard

Messaggio da kapello »

Lo script funziona perfettamente. Ripeto, lo usavo io con la 8.04 (non ricordo fino a che kernel), poi, come ho detto dall'inizio, magari alla fine le schede di rete non sono "perfettamente" uguali od il suo problema è un altro. Questo non si può sapere finchè non prova. Resta il fatto che anche io ho una Atheros montata su Asus ed il resoconto di lshw è praticamente lo stesso.
Quando il saggio indica la luna, lo sciocco guarda il dito - L'esistenza dovrebbe essere sempre colma di bellezza ed emozioni, ma sarebbe ugualmente vuota, senza contenuti. - I miei racconti - Ubuntu user #27862
Avatar utente
tapircik
Prode Principiante
Messaggi: 229
Iscrizione: sabato 11 ottobre 2008, 16:30

Re: [Driver] hardware: installazione driver matherboard

Messaggio da tapircik »

ru@edubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 10)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation G72 [GeForce 7300 LE] (rev a1)
02:00.0 Ethernet controller: Attansic Technology Corp. Unknown device 1026 (rev b0)
04:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
ru@edubuntu:~$
La scheda ethernet Realtek  è quella che sto usando per connettermi; l'altra è quella integrata nella matherboard e dovrebbe essere Atheros e sul cdrom con i driver ci sono i driver linux ma con estensione .tar.bz. Con alien, sarebbe possibile convertirli in .deb ma non capisco come avviare la conversione...
Inoltre, da synaptic ho installato atl2-source linux base driver per Athero fast ethernet adapter...
Ultima modifica di tapircik il venerdì 20 marzo 2009, 16:14, modificato 1 volta in totale.
Avatar utente
Guiodic
Accecante Asceta
Accecante Asceta
Messaggi: 28474
Iscrizione: martedì 24 aprile 2007, 15:28
Località: Roma
Contatti:

Re: [Driver] hardware: installazione driver matherboard

Messaggio da Guiodic »

quei driver ci sono già...
comunque si può provare a compilare il driver sul cd.
nel file tar.gz ci dovrebbe essere un README e/o un INSTALL, allegali qui (alien non c'entra)
Avatar utente
tapircik
Prode Principiante
Messaggi: 229
Iscrizione: sabato 11 ottobre 2008, 16:30

Re: [Driver] hardware: installazione driver matherboard

Messaggio da tapircik »

Codice: Seleziona tutto

Linux* Base Driver for the Atheros(R) AR8121/AR8113 PCI-E Ethernet Adapter

==========================================================================



Contents

========



- In This Release

- Building and Installation

- Command Line Parameters

- Additional Configurations

- Known Issues

- Support



In This Release

===============



This file describes the Linux* Base Driver for the Atheros(R) AR8121/AR8113 PCI-E 

Ethernet Adapter, version 1.0.0.5 This driver supports the 2.4.x and 2.6.x kernels.



This driver is only supported as a loadable module at this time. Atheros is not 

supplying patches against the kernel source to allow for static linking of 

the driver. For questions related to hardware requirements, refer to the 

documentation supplied with your Atheros(R) adapter. All hardware 

requirements listed apply to use with Linux.



Building and Installation

=========================



To build a binary RPM* package of this driver, run 'rpmbuild -tb 

<filename.tar.gz>'. Replace <filename.tar.gz> with the specific filename of 

the driver.



NOTE: For the build to work properly, the currently running kernel MUST match 

      the version and configuration of the installed kernel sources. If you 

      have just recompiled the kernel reboot the system now.



      RPM functionality has only been tested in Red Hat distributions.



1. Move the base driver tar file to the directory of your choice. For example,

   use /home/username/arl1e or /usr/local/src/arl1e.



2. Untar/unzip archive:



     tar zxf arl1e-x.x.x.x.tar.gz



3. Change to the driver src directory:



     cd arl1e-x.x.x.x/src/



4. Compile the driver module:



     make install



   The binary will be installed as:



     /lib/modules/<KERNEL VERSION>/kernel/drivers/net/arl1e.[k]o



   The install locations listed above are the default locations. They might 

   not be correct for certain Linux distributions. For more information, 

   see the ldistrib.txt file included in the driver tar.



5. Install the module:



     insmod arl1e <parameter>=<value>



6. Assign an IP address to the interface by entering the following, where

   x is the interface number:



     ifconfig ethx <IP_address>



7. Verify that the interface works. Enter the following, where <IP_address>

   is the IP address for another machine on the same subnet as the interface 

   that is being tested:



     ping  <IP_address> 



Command Line Parameters

=======================



If the driver is built as a module, the  following optional parameters are 

used by entering them on the command line with the modprobe or insmod command

using this syntax:



     modprobe arl1e [<option>=<VAL1>,<VAL2>,...]



     insmod arl1e [<option>=<VAL1>,<VAL2>,...] 



For example, with two L001 PCIE adapters, entering:



     insmod arl1e TxMemSize=80,128

loads the arl1e driver with 8KB TX memory for the first adapter and 10KB TX memory 

for the second adapter.



The default value for each parameter is generally the recommended setting,

unless otherwise noted.



    NOTES: A descriptor describes a data buffer and attributes related to the 

           data buffer. This information is accessed by the hardware.



MediaType

Valid Range: 0-4

	0    - auto-negotiate at all supported speeds

	1    - only link at 100Mbps Full Duplex

	2    - only link at 100Mbps Half Duplex

	3    - only link at 10Mbps Full Duplex

	4    - only link at 10Mbps Half Duplex

Default Value: 0

    MediaType forces the line speed/duplex to the specified value in 

    megabits per second(Mbps). If this parameter is not specified or is set 

    to 0 and the link partner is set to auto-negotiate, the board will 

    auto-detect the correct speed. 



IntModTimer

Valid Range: 50-65000

Default Value: 100

    This value represents the minmum interval between interrupts controller 

    generated. 



RxMemBlock

Valid Range: 16-512 

Default Value: 64

    This value is the number of receice memory block allocated by the driver. 

    Increasing this value allows the driver to buffer more incoming packets. 

    Each memory block is 1536 bytes.



    NOTE: Depending on the available system resources, the request for a

    higher number of receive descriptors may be denied.  In this case,

    use a lower number.



TxMemSize

Valid Range: 4-64

Default Value: 8

    This value is the number KB of transmit memory allocated by the driver. 

    Increasing this value allows the driver to queue more transmits.



    NOTE: Depending on the available system resources, the request for a

    higher number of transmit descriptors may be denied.  In this case,

    use a lower number.



FlashVendor

Valid Range: 0-2

Default Value: 0

    This value standards on vendor of spi flash used by the adapter.

    0 for Atmel, 1 for SST, 2 for ST

    



Additional Configurations

=========================



  Configuring the Driver on Different Distributions

  -------------------------------------------------



  Configuring a network driver to load properly when the system is started is

  distribution dependent. Typically, the configuration process involves adding

  an alias line to /etc/modules.conf as well as editing other system startup 

  scripts and/or configuration files. Many popular Linux distributions ship 

  with tools to make these changes for you. To learn the proper way to 

  configure a network device for your system, refer to your distribution 

  documentation. If during this process you are asked for the driver or module 

  name, the name for the Linux Base Driver for the Atheros AR8121/AR8113 is arl1e

  

  As an example, if you install the arl1e driver for two AR8121/AR8113 adapters 

  (eth0 and eth1) and set the speed and duplex to 10full and 100half, add the 

  following to modules.conf:



       alias eth0 arl1e

       alias eth1 arl1e

       options arl1e Speed=10,100 Duplex=2,1



  Viewing Link Messages

  ---------------------



  Link messages will not be displayed to the console if the distribution is 

  restricting system messages. In order to see network driver link messages 

  on your console, set dmesg to eight by entering the following:



       dmesg -n 8



  NOTE: This setting is not saved across reboots.





Known Issues

============



NOTE: For distribution-specific information, see the ldistrib.txt file 

      included in the driver tar.



  Driver Compilation

  ------------------



  When trying to compile the driver by running make install, the following

  error may occur: 



      "Linux kernel source not configured - missing version.h"



  To solve this issue, create the version.h file by going to the Linux source 

  tree and entering:



      make include/linux/version.h.





Support

=======



For general information, go to the Atheros support website at:



    http://support.atheros.com



If an issue is identified with the released source code on the supported

kernel with a supported adapter, email the specific information related to 

the issue to xiong.huang@atheros.com



License

=======



This software program is released under the terms of a license agreement 

between you ('Licensee') and Atheros. Do not use or load this software or any 

associated materials (collectively, the 'Software') until you have carefully 

read the full terms and conditions of the LICENSE located in this software 

package. By loading or using the Software, you agree to the terms of this 

Agreement. If you do not agree with the terms of this Agreement, do not 

install or use the Software.



* Other names and brands may be claimed as the property of others.
edit
aggiunti i tag code
Ultima modifica di Anonymous il lunedì 23 marzo 2009, 21:06, modificato 1 volta in totale.
Avatar utente
kapello
Entusiasta Emergente
Entusiasta Emergente
Messaggi: 2135
Iscrizione: lunedì 21 maggio 2007, 18:38
Desktop: KDE
Distribuzione: Kbuntu 13.10 amd64
Località: Torino
Contatti:

Re: [Driver] hardware: installazione driver matherboard

Messaggio da kapello »

Mamma mia modifica il post, metti tra tag code!
Quando il saggio indica la luna, lo sciocco guarda il dito - L'esistenza dovrebbe essere sempre colma di bellezza ed emozioni, ma sarebbe ugualmente vuota, senza contenuti. - I miei racconti - Ubuntu user #27862
Avatar utente
Guiodic
Accecante Asceta
Accecante Asceta
Messaggi: 28474
Iscrizione: martedì 24 aprile 2007, 15:28
Località: Roma
Contatti:

Re: [Driver] hardware: installazione driver matherboard

Messaggio da Guiodic »

mmm questi arl1e non esistono nel kernel di Ubuntu o forse si chiamano diversamente.

Comunque dovrebbero essere compatibili.

Allegami il file tar.bz.qui sul forum, se non entra mandamelo per email a guido.iodice (chiocciola) gmail (punto) com.

Dai

Codice: Seleziona tutto

uname -r
e copia cosa esce
Avatar utente
tapircik
Prode Principiante
Messaggi: 229
Iscrizione: sabato 11 ottobre 2008, 16:30

Re: [Driver] hardware: installazione driver matherboard

Messaggio da tapircik »

Ecco il risultato: 2.6.24-23-386
Ti ho spedito i file alla email indicata. Esistono i virus per ubuntu?
Avatar utente
Guiodic
Accecante Asceta
Accecante Asceta
Messaggi: 28474
Iscrizione: martedì 24 aprile 2007, 15:28
Località: Roma
Contatti:

Re: [Driver] hardware: installazione driver matherboard

Messaggio da Guiodic »

perché hai il kernel 386?
Avatar utente
tapircik
Prode Principiante
Messaggi: 229
Iscrizione: sabato 11 ottobre 2008, 16:30

Re: [Driver] hardware: installazione driver matherboard

Messaggio da tapircik »

Non saprei che dirti...Perchè quale kernel dovrei avere?
Avatar utente
Guiodic
Accecante Asceta
Accecante Asceta
Messaggi: 28474
Iscrizione: martedì 24 aprile 2007, 15:28
Località: Roma
Contatti:

Re: [Driver] hardware: installazione driver matherboard

Messaggio da Guiodic »

tapircik ha scritto: Non saprei che dirti...Perchè quale kernel dovrei avere?
il generic.

che processore hai?
Avatar utente
tapircik
Prode Principiante
Messaggi: 229
Iscrizione: sabato 11 ottobre 2008, 16:30

Re: [Driver] hardware: installazione driver matherboard

Messaggio da tapircik »

-cpu:0
          description: CPU
          product: Intel(R) Pentium(R) D CPU 2.80GHz
          vendor: Intel Corp.
          physical id: 4
          bus info: cpu@0
          version: 15.6.4
          serial: 0000-0F64-0000-0000-0000-0000
          slot: Socket 775
          size: 2800MHz
          capacity: 3800MHz
          width: 64 bits
          clock: 200MHz
          capabilities: boot fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx x86-64 constant_tsc pebs bts pni monitor ds_cpl est cid cx16 xtpr lahf_lm cpufreq
          configuration: id=0
ti allego la lista hardware
Allegati
lshw.txt
(14.33 KiB) Scaricato 13 volte
Ultima modifica di tapircik il sabato 21 marzo 2009, 10:06, modificato 1 volta in totale.
Avatar utente
Guiodic
Accecante Asceta
Accecante Asceta
Messaggi: 28474
Iscrizione: martedì 24 aprile 2007, 15:28
Località: Roma
Contatti:

Re: [Driver] hardware: installazione driver matherboard

Messaggio da Guiodic »

il generic dovrebbe andare benissimo..

installa il pacchetto linux-generic e disinstalla linux-image-2.6.24-23-386 nonchè ogni altro linux-image-numeroversione-386
Avatar utente
tapircik
Prode Principiante
Messaggi: 229
Iscrizione: sabato 11 ottobre 2008, 16:30

Re: [Driver] hardware: installazione driver matherboard

Messaggio da tapircik »

devo farlo con synaptic?
Avatar utente
tapircik
Prode Principiante
Messaggi: 229
Iscrizione: sabato 11 ottobre 2008, 16:30

Re: [Driver] hardware: installazione driver matherboard

Messaggio da tapircik »

Ho fatto e non si riavvia più: posso solo avviare come terminale :'(
Scrivi risposta

Ritorna a “Driver e periferiche”

Chi c’è in linea

Visualizzano questa sezione: 0 utenti iscritti e 14 ospiti