[Boot] problema avvio jaunty

Riconoscimento, installazione e configurazione delle periferiche.
Avatar utente
manuelik
Prode Principiante
Messaggi: 85
Iscrizione: domenica 8 giugno 2008, 16:35

[Boot] problema avvio jaunty

Messaggio da manuelik »

ciao a tutti, mi capita una cosa strana dopo aggiornamento a jaunty e adesso anche dopo la reinstallazione completa, il mio desk all'avvio da questa stringa:
Boot from (Hd 1,4) ext3 b9ob5154-bec4-447b-98c9-87c9eda896a2
starting up.........

e da qui si avvia dopo un minuto che cosa potrebbe essere, qualcuna ha idea di come mail si ferma in questa situazione per cosi tano tenpo?


Grazie
Alexx
Prode Principiante
Messaggi: 205
Iscrizione: sabato 1 novembre 2008, 21:36

Re: [Boot] problema avvio jaunty

Messaggio da Alexx »

prova a guardare dmesg da terminale
Avatar utente
manuelik
Prode Principiante
Messaggi: 85
Iscrizione: domenica 8 giugno 2008, 16:35

Re: [Boot] problema avvio jaunty

Messaggio da manuelik »

Grazie......fatto ma che dovrei cercare?

[    0.476282] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.476364] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
[    0.476367] pci 0000:00:05.0: PME# disabled
[    0.476389] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
[    0.476391] pci 0000:00:06.0: PME# disabled
[    0.476461] pci 0000:00:12.0: reg 10 io port: [0x8438-0x843f]
[    0.476468] pci 0000:00:12.0: reg 14 io port: [0x8454-0x8457]
[    0.476476] pci 0000:00:12.0: reg 18 io port: [0x8430-0x8437]
[    0.476483] pci 0000:00:12.0: reg 1c io port: [0x8450-0x8453]
[    0.476491] pci 0000:00:12.0: reg 20 io port: [0x8400-0x840f]
[    0.476498] pci 0000:00:12.0: reg 24 32bit mmio: [0xc0004000-0xc00043ff]
[    0.476518] pci 0000:00:12.0: set SATA to AHCI mode
[    0.476555] pci 0000:00:13.0: reg 10 32bit mmio: [0xc0005000-0xc0005fff]
[    0.476615] pci 0000:00:13.1: reg 10 32bit mmio: [0xc0006000-0xc0006fff]
[    0.476674] pci 0000:00:13.2: reg 10 32bit mmio: [0xc0007000-0xc0007fff]
[    0.476734] pci 0000:00:13.3: reg 10 32bit mmio: [0xc0008000-0xc0008fff]
[    0.476794] pci 0000:00:13.4: reg 10 32bit mmio: [0xc0009000-0xc0009fff]
[    0.476874] pci 0000:00:13.5: reg 10 32bit mmio: [0xc0004400-0xc00044ff]
[    0.476918] pci 0000:00:13.5: supports D1 D2
[    0.476919] pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot
[    0.476924] pci 0000:00:13.5: PME# disabled
[    0.476973] pci 0000:00:14.0: reg 10 io port: [0x8410-0x841f]
[    0.476980] pci 0000:00:14.0: reg 14 32bit mmio: [0xc0004800-0xc0004bff]
[    0.477053] pci 0000:00:14.1: reg 10 io port: [0x1f0-0x1f7]
[    0.477060] pci 0000:00:14.1: reg 14 io port: [0x3f4-0x3f7]
[    0.477067] pci 0000:00:14.1: reg 18 io port: [0x00-0x07]
[    0.477075] pci 0000:00:14.1: reg 1c io port: [0x00-0x03]
[    0.477082] pci 0000:00:14.1: reg 20 io port: [0x8420-0x842f]
[    0.477155] pci 0000:00:14.2: reg 10 64bit mmio: [0xc0000000-0xc0003fff]
[    0.477193] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[    0.477198] pci 0000:00:14.2: PME# disabled
[    0.477374] pci 0000:01:05.0: reg 10 32bit mmio: [0xc8000000-0xcfffffff]
[    0.477378] pci 0000:01:05.0: reg 14 io port: [0x9000-0x90ff]
[    0.477382] pci 0000:01:05.0: reg 18 32bit mmio: [0xc0100000-0xc010ffff]
[    0.477390] pci 0000:01:05.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[    0.477395] pci 0000:01:05.0: supports D1 D2
[    0.477409] pci 0000:00:01.0: bridge io port: [0x9000-0x9fff]
[    0.477412] pci 0000:00:01.0: bridge 32bit mmio: [0xc0100000-0xc01fffff]
[    0.477415] pci 0000:00:01.0: bridge 64bit mmio pref: [0xc8000000-0xcfffffff]
[    0.477465] pci 0000:00:05.0: bridge io port: [0x00-0xfff]
[    0.477468] pci 0000:00:05.0: bridge 32bit mmio: [0x000000-0x0fffff]
[    0.477510] pci 0000:05:00.0: reg 10 32bit mmio: [0xc0200000-0xc0203fff]
[    0.477553] pci 0000:05:00.0: supports D1 D2
[    0.477613] pci 0000:00:06.0: bridge 32bit mmio: [0xc0200000-0xc02fffff]
[    0.477660] pci 0000:08:00.0: reg 10 32bit mmio: [0xc0300000-0xc0301fff]
[    0.477713] pci 0000:08:00.0: supports D1 D2
[    0.477715] pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.477720] pci 0000:08:00.0: PME# disabled
[    0.477766] pci 0000:08:01.0: reg 10 32bit mmio: [0xc0302800-0xc03028ff]
[    0.477820] pci 0000:08:01.0: supports D1 D2
[    0.477821] pci 0000:08:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.477826] pci 0000:08:01.0: PME# disabled
[    0.477874] pci 0000:08:01.1: reg 10 32bit mmio: [0xc0302c00-0xc0302cff]
[    0.477927] pci 0000:08:01.1: supports D1 D2
[    0.477929] pci 0000:08:01.1: PME# supported from D0 D1 D2 D3hot D3cold
[    0.477934] pci 0000:08:01.1: PME# disabled
[    0.478005] pci 0000:00:14.4: transparent bridge
[    0.478015] pci 0000:00:14.4: bridge 32bit mmio: [0xc0300000-0xc03fffff]
[    0.478031] bus 00 -> node 0
[    0.478036] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.480180] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
[    0.480306] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT]
[    0.480448] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[    0.480561] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[    0.483267] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
[    0.483388] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
[    0.483507] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
[    0.483626] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
[    0.483745] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
[    0.483864] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
[    0.483984] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
[    0.484114] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
[    0.484234] ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled.
[    0.484392] ACPI: WMI: Mapper loaded
[    0.484562] SCSI subsystem initialized
[    0.484597] libata version 3.00 loaded.
[    0.484642] usbcore: registered new interface driver usbfs
[    0.484658] usbcore: registered new interface driver hub
[    0.484683] usbcore: registered new device driver usb
[    0.484772] PCI: Using ACPI for IRQ routing
[    0.484778] pci 0000:00:05.0: BAR 7: can't allocate resource
[    0.484780] pci 0000:00:05.0: BAR 8: can't allocate resource
[    0.496009] Bluetooth: Core ver 2.13
[    0.496048] NET: Registered protocol family 31
[    0.496050] Bluetooth: HCI device and connection manager initialized
[    0.496053] Bluetooth: HCI socket layer initialized
[    0.496055] NET: Registered protocol family 8
[    0.496056] NET: Registered protocol family 20
[    0.496066] NetLabel: Initializing
[    0.496067] NetLabel:  domain hash size = 128
[    0.496068] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.496082] NetLabel:  unlabeled traffic allowed by default
[    0.496294] AppArmor: AppArmor Filesystem Enabled
[    0.508005] pnp: PnP ACPI init
[    0.508017] ACPI: bus type pnp registered
[    0.510407] pnp 00:09: mem resource (0x0-0xfff) overlaps 0000:01:05.0 BAR 6 (0x0-0x1ffff), disabling
[    0.511481] pnp: PnP ACPI: found 10 devices
[    0.511483] ACPI: ACPI bus type pnp unregistered
[    0.511493] system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
[    0.511496] system 00:01: iomem range 0xfec00000-0xfec00fff has been reserved
[    0.511498] system 00:01: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.511505] system 00:08: ioport range 0x1080-0x1080 has been reserved
[    0.511508] system 00:08: ioport range 0x220-0x22f has been reserved
[    0.511510] system 00:08: ioport range 0x40b-0x40b has been reserved
[    0.511512] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[    0.511514] system 00:08: ioport range 0x4d6-0x4d6 has been reserved
[    0.511517] system 00:08: ioport range 0x530-0x537 has been reserved
[    0.511519] system 00:08: ioport range 0xc00-0xc01 has been reserved
[    0.511521] system 00:08: ioport range 0xc14-0xc14 has been reserved
[    0.511523] system 00:08: ioport range 0xc50-0xc52 has been reserved
[    0.511525] system 00:08: ioport range 0xc6c-0xc6c has been reserved
[    0.511528] system 00:08: ioport range 0xc6f-0xc6f has been reserved
[    0.511530] system 00:08: ioport range 0xcd0-0xcd3 has been reserved
[    0.511532] system 00:08: ioport range 0xcd4-0xcd5 has been reserved
[    0.511534] system 00:08: ioport range 0xcd6-0xcd7 has been reserved
[    0.511537] system 00:08: ioport range 0xcd8-0xcdf has been reserved
[    0.511539] system 00:08: ioport range 0x8000-0x805f has been reserved
[    0.511541] system 00:08: ioport range 0xf40-0xf47 has been reserved
[    0.511544] system 00:08: ioport range 0x87f-0x87f has been reserved
[    0.511549] system 00:09: iomem range 0xe0000-0xfffff could not be reserved
[    0.511551] system 00:09: iomem range 0xfff00000-0xffffffff could not be reserved
[    0.511554] system 00:09: iomem range 0xc0004800-0xc0004bff has been reserved
[    0.511556] system 00:09: iomem range 0xfed00000-0xfed003ff has been reserved
[    0.516232] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    0.516235] pci 0000:00:01.0:  IO window: 0x9000-0x9fff
[    0.516238] pci 0000:00:01.0:  MEM window: 0xc0100000-0xc01fffff
[    0.516241] pci 0000:00:01.0:  PREFETCH window: 0x000000c8000000-0x000000cfffffff
[    0.516244] pci 0000:00:05.0: PCI bridge, secondary bus 0000:02
[    0.516246] pci 0000:00:05.0:  IO window: disabled
[    0.516248] pci 0000:00:05.0:  MEM window: disabled
[    0.516250] pci 0000:00:05.0:  PREFETCH window: disabled
[    0.516254] pci 0000:00:06.0: PCI bridge, secondary bus 0000:05
[    0.516255] pci 0000:00:06.0:  IO window: disabled
[    0.516258] pci 0000:00:06.0:  MEM window: 0xc0200000-0xc02fffff
[    0.516260] pci 0000:00:06.0:  PREFETCH window: disabled
[    0.516263] pci 0000:00:14.4: PCI bridge, secondary bus 0000:08
[    0.516265] pci 0000:00:14.4:  IO window: disabled
[    0.516271] pci 0000:00:14.4:  MEM window: 0xc0300000-0xc03fffff
[    0.516275] pci 0000:00:14.4:  PREFETCH window: disabled
[    0.516290] pci 0000:00:05.0: setting latency timer to 64
[    0.516294] pci 0000:00:06.0: setting latency timer to 64
[    0.516302] bus: 00 index 0 io port: [0x00-0xffff]
[    0.516304] bus: 00 index 1 mmio: [0x000000-0xffffffffffffffff]
[    0.516306] bus: 01 index 0 io port: [0x9000-0x9fff]
[    0.516308] bus: 01 index 1 mmio: [0xc0100000-0xc01fffff]
[    0.516309] bus: 01 index 2 mmio: [0xc8000000-0xcfffffff]
[    0.516311] bus: 01 index 3 mmio: [0x0-0x0]
[    0.516313] bus: 02 index 0 mmio: [0x0-0xfff]
[    0.516314] bus: 02 index 1 mmio: [0x0-0xfffff]
[    0.516316] bus: 02 index 2 mmio: [0x0-0x0]
[    0.516317] bus: 02 index 3 mmio: [0x0-0x0]
[    0.516319] bus: 05 index 0 mmio: [0x0-0x0]
[    0.516321] bus: 05 index 1 mmio: [0xc0200000-0xc02fffff]
[    0.516322] bus: 05 index 2 mmio: [0x0-0x0]
[    0.516324] bus: 05 index 3 mmio: [0x0-0x0]
[    0.516325] bus: 08 index 0 mmio: [0x0-0x0]
[    0.516327] bus: 08 index 1 mmio: [0xc0300000-0xc03fffff]
[    0.516329] bus: 08 index 2 mmio: [0x0-0x0]
[    0.516330] bus: 08 index 3 io port: [0x00-0xffff]
[    0.516332] bus: 08 index 4 mmio: [0x000000-0xffffffffffffffff]
[    0.516343] NET: Registered protocol family 2
[    0.552046] IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
[    0.552368] TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
[    0.553356] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[    0.553860] TCP: Hash tables configured (established 131072 bind 65536)
[    0.553863] TCP reno registered
[    0.564075] NET: Registered protocol family 1
[    0.564198] checking if image is initramfs... it is
[    1.019976] Switched to high resolution mode on CPU 0
[    1.151709] Freeing initrd memory: 7764k freed
[    1.155925] audit: initializing netlink socket (disabled)
[    1.155939] type=2000 audit(1243800110.152:1): initialized
[    1.163922] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    1.165066] VFS: Disk quotas dquot_6.5.1
[    1.165114] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    1.165626] fuse init (API version 7.10)
[    1.165697] msgmni has been set to 1720
[    1.165848] alg: No test for stdrng (krng)
[    1.165858] io scheduler noop registered
[    1.165859] io scheduler anticipatory registered
[    1.165861] io scheduler deadline registered
[    1.165899] io scheduler cfq registered (default)
[    1.165907] pci 0000:00:00.0: MSI quirk detected; MSI disabled
[    1.165988] pci 0000:01:05.0: Boot video device
[    1.166067] pcieport-driver 0000:00:05.0: setting latency timer to 64
[    1.166087] pcieport-driver 0000:00:05.0: found MSI capability
[    1.166090] pci_express 0000:00:05.0:pcie00: allocate port service
[    1.166103] pci_express 0000:00:05.0:pcie02: allocate port service
[    1.166136] pcieport-driver 0000:00:06.0: setting latency timer to 64
[    1.166154] pcieport-driver 0000:00:06.0: found MSI capability
[    1.166156] pci_express 0000:00:06.0:pcie00: allocate port service
[    1.166167] pci_express 0000:00:06.0:pcie02: allocate port service
[    1.166213] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.166319] ACPI Error (exresop-0103): Needed type [Reference], found [Device] ffff88003703a7c0 [20080926]
[    1.166325] ACPI Exception (dswexec-0445): AE_AML_OPERAND_TYPE, While resolving operands for [OpcodeName unavailable] [20080926]
[    1.166331] ACPI Error (psparse-0524): Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff8800370b5a20), AE_AML_OPERAND_TYPE
[    1.166459] ACPI Error (exresop-0103): Needed type [Reference], found [Device] ffff88003703a7c0 [20080926]
[    1.166463] ACPI Exception (dswexec-0445): AE_AML_OPERAND_TYPE, While resolving operands for [OpcodeName unavailable] [20080926]
[    1.166468] ACPI Error (psparse-0524): Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff8800370b5a20), AE_AML_OPERAND_TYPE
[    1.166529] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.167535] ACPI: AC Adapter [ACAD] (off-line)
[    1.564146] ACPI: Battery Slot [BAT1] (battery present)
[    1.564208] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    1.564211] ACPI: Power Button (FF) [PWRF]
[    1.564252] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    1.564254] ACPI: Power Button (CM) [PWRB]
[    1.564303] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
[    1.564311] ACPI: Sleep Button (CM) [SLPB]
[    1.564350] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
[    1.565279] ACPI: Lid Switch [LID]
[    1.565458] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[    1.565481] processor ACPI_CPU:00: registered as cooling_device0
[    1.565484] ACPI: Processor [CPU0] (supports 8 throttling states)
[    1.571037] thermal LNXTHERM:01: registered as thermal_zone0
[    1.573663] ACPI: Thermal Zone [THRM] (35 C)
[    1.608126] Linux agpgart interface v0.103
[    1.608135] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.608936] brd: module loaded
[    1.609213] loop: module loaded
[    1.609283] Fixed MDIO Bus: probed
[    1.609289] PPP generic driver version 2.4.2
[    1.609344] input: Macintosh mouse button emulation as /devices/virtual/input/input4
[    1.609370] Driver 'sd' needs updating - please use bus_type methods
[    1.609378] Driver 'sr' needs updating - please use bus_type methods
[    1.609410] ahci 0000:00:12.0: version 3.0
[    1.609429] ahci 0000:00:12.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    1.609464] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
[    1.609560] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[    1.609563] ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pmp pio slum part
[    1.610006] scsi0 : ahci
[    1.610120] scsi1 : ahci
[    1.610170] scsi2 : ahci
[    1.610217] scsi3 : ahci
[    1.610301] ata1: SATA max UDMA/133 abar m1024@0xc0004000 port 0xc0004100 irq 22
[    1.610305] ata2: SATA max UDMA/133 abar m1024@0xc0004000 port 0xc0004180 irq 22
[    1.610308] ata3: SATA max UDMA/133 abar m1024@0xc0004000 port 0xc0004200 irq 22
[    1.610312] ata4: SATA max UDMA/133 abar m1024@0xc0004000 port 0xc0004280 irq 22
[    2.092008] ata1: softreset failed (device not ready)
[    2.092049] ata1: failed due to HW bug, retry pmp=0
[    2.256020] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.261810] ata1.00: ATA-7: SAMSUNG HM060HI, YD100-15, max UDMA7
[    2.261813] ata1.00: 117210240 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    2.261830] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[    2.267712] ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
[    2.267715] ata1.00: configured for UDMA/133
[    2.600023] ata2: SATA link down (SStatus 0 SControl 300)
[    2.936023] ata3: SATA link down (SStatus 0 SControl 300)
[    3.272023] ata4: SATA link down (SStatus 0 SControl 300)
[    3.288036] isa bounce pool size: 16 pages
[    3.288111] scsi 0:0:0:0: Direct-Access    ATA      SAMSUNG HM060HI  YD10 PQ: 0 ANSI: 5
[    3.288197] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors: (60.0 GB/55.8 GiB)
[    3.288213] sd 0:0:0:0: [sda] Write Protect is off
[    3.288215] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.288237] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.288297] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors: (60.0 GB/55.8 GiB)
[    3.288309] sd 0:0:0:0: [sda] Write Protect is off
[    3.288311] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.288332] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.288336]  sda: sda1 sda2
[    3.346091] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.346137] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.346371] pata_atiixp 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.346407] pata_atiixp 0000:00:14.1: setting latency timer to 64
[    3.346502] scsi4 : pata_atiixp
[    3.346556] scsi5 : pata_atiixp
[    3.347307] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8420 irq 14
[    3.347309] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8428 irq 15
[    3.508516] ata5.00: ATAPI: HL-DT-ST DVDRAM GSA-4080N, 0H09, max UDMA/33
[    3.524464] ata5.00: configured for UDMA/33
[    3.683957] scsi 4:0:0:0: CD-ROM            HL-DT-ST DVDRAM GSA-4080N 0H09 PQ: 0 ANSI: 5
[    3.695644] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    3.695647] Uniform CD-ROM driver Revision: 3.20
[    3.695747] sr 4:0:0:0: Attached scsi CD-ROM sr0
[    3.695798] sr 4:0:0:0: Attached scsi generic sg1 type 5
[    3.696144] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.696167] ehci_hcd 0000:00:13.5: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    3.696188] ehci_hcd 0000:00:13.5: EHCI Host Controller
[    3.696242] ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1
[    3.696271] ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
[    3.696292] ehci_hcd 0000:00:13.5: debug port 1
[    3.696314] ehci_hcd 0000:00:13.5: irq 19, io mem 0xc0004400
[    3.708008] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00
[    3.708086] usb usb1: configuration #1 chosen from 1 choice
[    3.708109] hub 1-0:1.0: USB hub found
[    3.708117] hub 1-0:1.0: 10 ports detected
[    3.708231] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.708245] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.708255] ohci_hcd 0000:00:13.0: OHCI Host Controller
[    3.708295] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
[    3.708316] ohci_hcd 0000:00:13.0: irq 16, io mem 0xc0005000
[    3.764072] usb usb2: configuration #1 chosen from 1 choice
[    3.764095] hub 2-0:1.0: USB hub found
[    3.764104] hub 2-0:1.0: 2 ports detected
[    3.764180] ohci_hcd 0000:00:13.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    3.764192] ohci_hcd 0000:00:13.1: OHCI Host Controller
[    3.764227] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
[    3.764249] ohci_hcd 0000:00:13.1: irq 17, io mem 0xc0006000
[    3.820075] usb usb3: configuration #1 chosen from 1 choice
[    3.820095] hub 3-0:1.0: USB hub found
[    3.820105] hub 3-0:1.0: 2 ports detected
[    3.820181] ohci_hcd 0000:00:13.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    3.820191] ohci_hcd 0000:00:13.2: OHCI Host Controller
[    3.820225] ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
[    3.820245] ohci_hcd 0000:00:13.2: irq 18, io mem 0xc0007000
[    3.876072] usb usb4: configuration #1 chosen from 1 choice
[    3.876093] hub 4-0:1.0: USB hub found
[    3.876102] hub 4-0:1.0: 2 ports detected
[    3.876178] ohci_hcd 0000:00:13.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    3.876188] ohci_hcd 0000:00:13.3: OHCI Host Controller
[    3.876234] ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
[    3.876249] ohci_hcd 0000:00:13.3: irq 17, io mem 0xc0008000
[    3.932078] usb usb5: configuration #1 chosen from 1 choice
[    3.932103] hub 5-0:1.0: USB hub found
[    3.932121] hub 5-0:1.0: 2 ports detected
[    3.932194] ohci_hcd 0000:00:13.4: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    3.932204] ohci_hcd 0000:00:13.4: OHCI Host Controller
[    3.932241] ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
[    3.932257] ohci_hcd 0000:00:13.4: irq 18, io mem 0xc0009000
[    3.988074] usb usb6: configuration #1 chosen from 1 choice
[    3.988099] hub 6-0:1.0: USB hub found
[    3.988108] hub 6-0:1.0: 2 ports detected
[    3.988189] uhci_hcd: USB Universal Host Controller Interface driver
[    3.988263] usbcore: registered new interface driver libusual
[    3.988293] usbcore: registered new interface driver usbserial
[    3.988302] USB Serial support registered for generic
[    4.228006] usb 2-1: new low speed USB device using ohci_hcd and address 2
[    4.394993] usb 2-1: configuration #1 chosen from 1 choice
[    4.397053] usbcore: registered new interface driver usbserial_generic
[    4.397055] usbserial: USB Serial Driver core
[    4.397097] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12
[    4.399182] serio: i8042 KBD port at 0x60,0x64 irq 1
[    4.399187] serio: i8042 AUX port at 0x60,0x64 irq 12
[    4.408032] mice: PS/2 mouse device common for all mice
[    4.468053] rtc_cmos 00:04: RTC can wake from S4
[    4.468086] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[    4.468111] rtc0: alarms up to one month, 114 bytes nvram
[    4.468171] device-mapper: uevent: version 1.0.3
[    4.468274] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[    4.468316] device-mapper: multipath: version 1.0.5 loaded
[    4.468318] device-mapper: multipath round-robin: version 1.0.0 loaded
[    4.468411] cpuidle: using governor ladder
[    4.468462] cpuidle: using governor menu
[    4.468844] TCP cubic registered
[    4.468908] NET: Registered protocol family 10
[    4.469252] lo: Disabled Privacy Extensions
[    4.469511] NET: Registered protocol family 17
[    4.469529] Bluetooth: L2CAP ver 2.11
[    4.469530] Bluetooth: L2CAP socket layer initialized
[    4.469533] Bluetooth: SCO (Voice Link) ver 0.6
[    4.469534] Bluetooth: SCO socket layer initialized
[    4.469557] Bluetooth: RFCOMM socket layer initialized
[    4.469563] Bluetooth: RFCOMM TTY layer initialized
[    4.469564] Bluetooth: RFCOMM ver 1.10
[    4.469584] powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology MK-36 processors (1 cpu cores) (version 2.20.00)
[    4.469631] powernow-k8:    0 : fid 0xc (2000 MHz), vid 0x10
[    4.469633] powernow-k8:    1 : fid 0xa (1800 MHz), vid 0x12
[    4.469635] powernow-k8:    2 : fid 0x8 (1600 MHz), vid 0x14
[    4.469636] powernow-k8:    3 : fid 0x0 (800 MHz), vid 0x18
[    4.469751] registered taskstats version 1
[    4.469881]  Magic number: 9:407:44
[    4.469968] rtc_cmos 00:04: setting system clock to 2009-05-31 20:01:55 UTC (1243800115)
[    4.469971] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    4.469973] EDD information not available.
[    4.470019] Freeing unused kernel memory: 536k freed
[    4.470296] Write protecting the kernel read-only data: 6708k
[    4.513510] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[    5.530164] usbcore: registered new interface driver hiddev
[    5.538108] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:13.0/usb2/2-1/2-1:1.0/input/input6
[    5.564096] generic-usb 0003:046D:C019.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:13.0-1/input0
[    5.564117] usbcore: registered new interface driver usbhid
[    5.564120] usbhid: v2.6:USB HID core driver
[    6.392044] Marking TSC unstable due to TSC halts in idle
[    6.456471] PM: Starting manual resume from disk
[    6.456475] PM: Resume from partition 8:5
[    6.456477] PM: Checking hibernation image.
[    6.456726] PM: Resume from disk failed.
[    6.510762] kjournald starting.  Commit interval 5 seconds
[    6.510773] EXT3-fs: mounted filesystem with ordered data mode.
[  13.758249] udev: starting version 141
[  14.014800] acpi device:1e: registered as cooling_device1
[  14.014991] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:1b/device:1c/input/input7
[  14.044113] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[  14.225919] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[  14.361992] ieee80211_crypt: registered algorithm 'NULL'
[  14.442267] wl: module license '' taints kernel.
[  14.444542] wl 0000:05:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[  14.444549] wl 0000:05:00.0: setting latency timer to 64
[  14.466422] ieee80211_crypt: registered algorithm 'TKIP'
[  14.466865] eth0: Broadcom BCM4311 802.11 Wireless Controller 5.10.79.10
[  14.504299] sdhci: Secure Digital Host Controller Interface driver
[  14.504302] sdhci: Copyright(c) Pierre Ossman
[  14.533358] sdhci-pci 0000:08:01.0: SDHCI controller found [1180:0822] (rev 19)
[  14.533381] sdhci-pci 0000:08:01.0: PCI INT B -> GSI 20 (level, low) -> IRQ 20
[  14.536512] mmc0: SDHCI controller on PCI [0000:08:01.0] using PIO
[  14.573582] ricoh-mmc: Ricoh MMC Controller disabling driver
[  14.573586] ricoh-mmc: Copyright(c) Philip Langdale
[  14.573632] ricoh-mmc: Ricoh MMC controller found at 0000:08:01.1 [1180:0843] (rev 1)
[  14.573638] ricoh-mmc: Main Ricoh function not found. Cannot disable controller.
[  14.594649] piix4_smbus 0000:00:14.0: SMBus Host Controller at 0x8410, revision 0
[  14.791072] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[  14.923417] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[  14.995212] b44 0000:08:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
[  15.052216] ssb: Sonics Silicon Backplane found on PCI device 0000:08:00.0
[  15.052282] b44.c:v2.0
[  15.072756] eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:19:b9:5d:c8:18
[  15.084712] udev: renamed network interface eth1 to eth0
[  15.128905] udev: renamed network interface eth0_rename to eth1
[  15.154290] HDA Intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[  15.463807] lp: driver loaded but no devices found
[  15.555253] Adding 2441840k swap on /dev/sda5.  Priority:-1 extents:1 across:2441840k
[  15.578146] EXT3 FS on sda1, internal journal
[  15.675261] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x180b1, caps: 0xa04713/0x200000
[  15.719460] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
[  16.347769] type=1505 audit(1243800127.374:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=1942
[  16.396260] type=1505 audit(1243800127.426:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1946
[  16.396413] type=1505 audit(1243800127.426:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1946
[  16.396460] type=1505 audit(1243800127.426:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1946
[  16.396502] type=1505 audit(1243800127.426:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1946
[  16.529057] type=1505 audit(1243800127.558:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1951
[  16.529241] type=1505 audit(1243800127.558:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1951
[  16.559901] type=1505 audit(1243800127.586:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1955
[  22.118108] vboxdrv: Trying to deactivate the NMI watchdog permanently...
[  22.118112] vboxdrv: Successfully done.
[  22.118113] vboxdrv: Found 1 processor cores.
[  22.118166] VBoxDrv: dbg - g_abExecMemory=ffffffffa03bcf00
[  22.118214] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[  22.118216] vboxdrv: Successfully loaded version 2.2.2 (interface 0x000a0009).
[  22.328312] VBoxNetFlt: dbg - g_abExecMemory=ffffffffa055cbc0
[  23.981869] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[  23.981872] Bluetooth: BNEP filters: protocol multicast
[  24.001947] Bridge firewalling registered
[  26.146765] pci 0000:01:05.0: power state changed by ACPI to D0
[  26.146775] pci 0000:01:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[  26.549159] [drm] Initialized drm 1.1.0 20060810
[  26.620069] [drm] Initialized radeon 1.29.0 20080528 on minor 0
[  26.633684] ppdev: user-space parallel port driver
[  27.087923] [drm] Setting GART location based on new memory map
[  27.088213] [drm] Loading R300 Microcode
[  27.088232] [drm] Num pipes: 2
[  27.088238] [drm] writeback test succeeded in 1 usecs
[  29.974979] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  33.640020] eth1: no IPv6 routers present
[  89.016016] Clocksource tsc unstable (delta = -100044489 ns)
[  92.895102] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
[  780.584540] APIC error on CPU0: 00(40)

Qiesto à quello che viene fuori
Avatar utente
manuelik
Prode Principiante
Messaggi: 85
Iscrizione: domenica 8 giugno 2008, 16:35

Re: [Boot] problema avvio jaunty

Messaggio da manuelik »

NO SCUSA SONO UN PO PIRLA ho dato il comando dal portatile che è ok ah ah ah scusa ancora prvo ora con il  desk (era spento) ahah sono difuori scusa.

Ciao
Avatar utente
manuelik
Prode Principiante
Messaggi: 85
Iscrizione: domenica 8 giugno 2008, 16:35

Re: [Boot] problema avvio jaunty

Messaggio da manuelik »

ecco è questo che risulta dopo il comndo sul pc che ha il problema sopra citato

[    0.440489] NET: Registered protocol family 16
[    0.440489] EISA bus registered
[    0.440489] ACPI: bus type pci registered
[    0.440489] PCI: MCFG configuration 0: base d0000000 segment 0 buses 0 - 255
[    0.440489] PCI: MCFG area at d0000000 reserved in E820
[    0.440489] PCI: Using MMCONFIG for extended config space
[    0.440489] PCI: Using configuration type 1 for base access
[    0.441607] ACPI: EC: Look up EC in DSDT
[    0.450680] ACPI: Interpreter enabled
[    0.450692] ACPI: (supports S0 S3 S4 S5)
[    0.450723] ACPI: Using IOAPIC for interrupt routing
[    0.455186] ACPI: No dock devices found.
[    0.455200] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.455358] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[    0.455365] pci 0000:00:01.0: PME# disabled
[    0.455466] pci 0000:00:02.5: reg 10 io port: [0x00-0x07]
[    0.455474] pci 0000:00:02.5: reg 14 io port: [0x00-0x03]
[    0.455482] pci 0000:00:02.5: reg 18 io port: [0x00-0x07]
[    0.455490] pci 0000:00:02.5: reg 1c io port: [0x00-0x03]
[    0.455499] pci 0000:00:02.5: reg 20 io port: [0xf000-0xf00f]
[    0.455554] pci 0000:00:02.7: reg 10 io port: [0xc800-0xc8ff]
[    0.455563] pci 0000:00:02.7: reg 14 io port: [0xcc00-0xcc7f]
[    0.455603] pci 0000:00:02.7: supports D1 D2
[    0.455606] pci 0000:00:02.7: PME# supported from D3hot D3cold
[    0.455611] pci 0000:00:02.7: PME# disabled
[    0.455638] pci 0000:00:03.0: reg 10 32bit mmio: [0xf8000000-0xf8000fff]
[    0.455699] pci 0000:00:03.1: reg 10 32bit mmio: [0xf8001000-0xf8001fff]
[    0.455759] pci 0000:00:03.2: reg 10 32bit mmio: [0xf8002000-0xf8002fff]
[    0.455832] pci 0000:00:03.3: reg 10 32bit mmio: [0xf8003000-0xf8003fff]
[    0.455878] pci 0000:00:03.3: PME# supported from D0 D3hot D3cold
[    0.455883] pci 0000:00:03.3: PME# disabled
[    0.455929] pci 0000:00:05.0: reg 10 io port: [0xd000-0xd007]
[    0.455937] pci 0000:00:05.0: reg 14 io port: [0xd400-0xd403]
[    0.455945] pci 0000:00:05.0: reg 18 io port: [0xd800-0xd807]
[    0.455954] pci 0000:00:05.0: reg 1c io port: [0xdc00-0xdc03]
[    0.455962] pci 0000:00:05.0: reg 20 io port: [0xe000-0xe00f]
[    0.455970] pci 0000:00:05.0: reg 24 io port: [0xe400-0xe47f]
[    0.456011] pci 0000:00:05.0: PME# supported from D3cold
[    0.456016] pci 0000:00:05.0: PME# disabled
[    0.456092] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
[    0.456098] pci 0000:00:06.0: PME# disabled
[    0.456178] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
[    0.456183] pci 0000:00:07.0: PME# disabled
[    0.456234] pci 0000:00:09.0: reg 10 io port: [0xe800-0xe8ff]
[    0.456243] pci 0000:00:09.0: reg 14 32bit mmio: [0xf8004000-0xf80040ff]
[    0.456284] pci 0000:00:09.0: supports D1 D2
[    0.456286] pci 0000:00:09.0: PME# supported from D1 D2 D3hot D3cold
[    0.456291] pci 0000:00:09.0: PME# disabled
[    0.456335] pci 0000:00:0c.0: reg 10 32bit mmio: [0xf8005000-0xf80057ff]
[    0.456344] pci 0000:00:0c.0: reg 14 io port: [0xec00-0xec7f]
[    0.456386] pci 0000:00:0c.0: supports D2
[    0.456388] pci 0000:00:0c.0: PME# supported from D2 D3hot D3cold
[    0.456393] pci 0000:00:0c.0: PME# disabled
[    0.456477] pci 0000:01:00.0: reg 10 32bit mmio: [0xf0000000-0xf3ffffff]
[    0.456491] pci 0000:01:00.0: reg 14 64bit mmio: [0xe0000000-0xefffffff]
[    0.456507] pci 0000:01:00.0: reg 1c 64bit mmio: [0xf4000000-0xf4ffffff]
[    0.456523] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[    0.456597] pci 0000:00:01.0: bridge 32bit mmio: [0xf0000000-0xf7ffffff]
[    0.456606] pci 0000:00:01.0: bridge 64bit mmio pref: [0xe0000000-0xefffffff]
[    0.456673] pci 0000:00:06.0: bridge io port: [0xa000-0xafff]
[    0.456747] pci 0000:00:07.0: bridge io port: [0xb000-0xbfff]
[    0.456778] bus 00 -> node 0
[    0.456787] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.478559] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[    0.479404] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    0.479549] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[    0.479694] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[    0.479838] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 9 10 11 12 14 15)
[    0.479982] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[    0.480148] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 *6 7 9 10 11 12 14 15)
[    0.480291] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[    0.480519] ACPI: WMI: Mapper loaded
[    0.480634] SCSI subsystem initialized
[    0.480634] libata version 3.00 loaded.
[    0.480634] usbcore: registered new interface driver usbfs
[    0.480634] usbcore: registered new interface driver hub
[    0.480634] usbcore: registered new device driver usb
[    0.480634] PCI: Using ACPI for IRQ routing
[    0.488015] Bluetooth: Core ver 2.13
[    0.488036] NET: Registered protocol family 31
[    0.488036] Bluetooth: HCI device and connection manager initialized
[    0.488036] Bluetooth: HCI socket layer initialized
[    0.488036] NET: Registered protocol family 8
[    0.488037] NET: Registered protocol family 20
[    0.488054] NetLabel: Initializing
[    0.488056] NetLabel:  domain hash size = 128
[    0.488058] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.488076] NetLabel:  unlabeled traffic allowed by default
[    0.488184] AppArmor: AppArmor Filesystem Enabled
[    0.492017] pnp: PnP ACPI init
[    0.492035] ACPI: bus type pnp registered
[    0.495190] pnp: PnP ACPI: found 11 devices
[    0.495194] ACPI: ACPI bus type pnp unregistered
[    0.495200] PnPBIOS: Disabled by ACPI PNP
[    0.495214] system 00:01: ioport range 0x4d0-0x4d1 has been reserved
[    0.495217] system 00:01: ioport range 0x290-0x29f has been reserved
[    0.495220] system 00:01: ioport range 0x800-0x805 has been reserved
[    0.495223] system 00:01: ioport range 0x880-0x88f has been reserved
[    0.495235] system 00:09: iomem range 0xd0000000-0xdfffffff has been reserved
[    0.495243] system 00:0a: iomem range 0xd0000-0xd7fff has been reserved
[    0.495246] system 00:0a: iomem range 0xf0000-0xf7fff could not be reserved
[    0.495249] system 00:0a: iomem range 0xf8000-0xfbfff could not be reserved
[    0.495252] system 00:0a: iomem range 0xfc000-0xfffff could not be reserved
[    0.495255] system 00:0a: iomem range 0x3fff0000-0x3fffffff could not be reserved
[    0.495258] system 00:0a: iomem range 0xffff0000-0xffffffff has been reserved
[    0.495261] system 00:0a: iomem range 0x0-0x9ffff could not be reserved
[    0.495264] system 00:0a: iomem range 0x100000-0x3ffeffff could not be reserved
[    0.495268] system 00:0a: iomem range 0xffee0000-0xffefffff has been reserved
[    0.495271] system 00:0a: iomem range 0xfffe0000-0xfffeffff has been reserved
[    0.495274] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
[    0.495277] system 00:0a: iomem range 0xfee00000-0xfeefffff has been reserved
[    0.530030] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    0.530033] pci 0000:00:01.0:  IO window: disabled
[    0.530040] pci 0000:00:01.0:  MEM window: 0xf0000000-0xf7ffffff
[    0.530046] pci 0000:00:01.0:  PREFETCH window: 0x000000e0000000-0x000000efffffff
[    0.530054] pci 0000:00:06.0: PCI bridge, secondary bus 0000:02
[    0.530058] pci 0000:00:06.0:  IO window: 0xa000-0xafff
[    0.530065] pci 0000:00:06.0:  MEM window: disabled
[    0.530070] pci 0000:00:06.0:  PREFETCH window: disabled
[    0.530078] pci 0000:00:07.0: PCI bridge, secondary bus 0000:03
[    0.530081] pci 0000:00:07.0:  IO window: 0xb000-0xbfff
[    0.530088] pci 0000:00:07.0:  MEM window: disabled
[    0.530092] pci 0000:00:07.0:  PREFETCH window: disabled
[    0.530112] pci 0000:00:01.0: setting latency timer to 64
[    0.530129] pci 0000:00:06.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[    0.530134] pci 0000:00:06.0: setting latency timer to 64
[    0.530146] pci 0000:00:07.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.530151] pci 0000:00:07.0: setting latency timer to 64
[    0.530156] bus: 00 index 0 io port: [0x00-0xffff]
[    0.530159] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[    0.530162] bus: 01 index 0 mmio: [0x0-0x0]
[    0.530164] bus: 01 index 1 mmio: [0xf0000000-0xf7ffffff]
[    0.530167] bus: 01 index 2 mmio: [0xe0000000-0xefffffff]
[    0.530169] bus: 01 index 3 mmio: [0x0-0x0]
[    0.530172] bus: 02 index 0 io port: [0xa000-0xafff]
[    0.530174] bus: 02 index 1 mmio: [0x0-0x0]
[    0.530176] bus: 02 index 2 mmio: [0x0-0x0]
[    0.530178] bus: 02 index 3 mmio: [0x0-0x0]
[    0.530180] bus: 03 index 0 io port: [0xb000-0xbfff]
[    0.530183] bus: 03 index 1 mmio: [0x0-0x0]
[    0.530185] bus: 03 index 2 mmio: [0x0-0x0]
[    0.530187] bus: 03 index 3 mmio: [0x0-0x0]
[    0.530197] NET: Registered protocol family 2
[    0.544138] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.544528] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.545233] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.545789] TCP: Hash tables configured (established 131072 bind 65536)
[    0.545793] TCP reno registered
[    0.552238] NET: Registered protocol family 1
[    0.552424] checking if image is initramfs... it is
[    1.028642] Switched to high resolution mode on CPU 1
[    1.032126] Switched to high resolution mode on CPU 0
[    1.136641] Freeing initrd memory: 7369k freed
[    1.136940] cpufreq: No nForce2 chipset.
[    1.137156] audit: initializing netlink socket (disabled)
[    1.137198] type=2000 audit(1243802874.137:1): initialized
[    1.145302] highmem bounce pool size: 64 pages
[    1.145310] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.146932] VFS: Disk quotas dquot_6.5.1
[    1.147011] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.147812] fuse init (API version 7.10)
[    1.147919] msgmni has been set to 1724
[    1.148161] alg: No test for stdrng (krng)
[    1.148188] io scheduler noop registered
[    1.148191] io scheduler anticipatory registered
[    1.148193] io scheduler deadline registered
[    1.148213] io scheduler cfq registered (default)
[    1.232109] pci 0000:01:00.0: Boot video device
[    1.234712] pcieport-driver 0000:00:01.0: setting latency timer to 64
[    1.234777] pcieport-driver 0000:00:01.0: found MSI capability
[    1.234817] pcieport-driver 0000:00:01.0: irq 2303 for MSI/MSI-X
[    1.234834] pci_express 0000:00:01.0:pcie00: allocate port service
[    1.234935] pcieport-driver 0000:00:06.0: setting latency timer to 64
[    1.235000] pcieport-driver 0000:00:06.0: found MSI capability
[    1.235034] pcieport-driver 0000:00:06.0: irq 2302 for MSI/MSI-X
[    1.235051] pci_express 0000:00:06.0:pcie00: allocate port service
[    1.235069] pci_express 0000:00:06.0:pcie01: allocate port service
[    1.235086] pci_express 0000:00:06.0:pcie03: allocate port service
[    1.235175] pcieport-driver 0000:00:07.0: setting latency timer to 64
[    1.235240] pcieport-driver 0000:00:07.0: found MSI capability
[    1.235274] pcieport-driver 0000:00:07.0: irq 2301 for MSI/MSI-X
[    1.235290] pci_express 0000:00:07.0:pcie00: allocate port service
[    1.235307] pci_express 0000:00:07.0:pcie01: allocate port service
[    1.235324] pci_express 0000:00:07.0:pcie03: allocate port service
[    1.236613] aer 0000:00:06.0:pcie01: AER service couldn't init device: no _OSC support
[    1.237816] aer 0000:00:07.0:pcie01: AER service couldn't init device: no _OSC support
[    1.237832] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.237847] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.238023] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    1.238027] ACPI: Power Button (FF) [PWRF]
[    1.238083] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    1.238086] ACPI: Power Button (CM) [PWRB]
[    1.238401] processor ACPI_CPU:00: registered as cooling_device0
[    1.238454] processor ACPI_CPU:01: registered as cooling_device1
[    1.240244] isapnp: Scanning for PnP cards...
[    1.591946] isapnp: No Plug & Play device found
[    1.601207] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.601309] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.601699] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.602701] brd: module loaded
[    1.603133] loop: module loaded
[    1.603226] Fixed MDIO Bus: probed
[    1.603233] PPP generic driver version 2.4.2
[    1.603308] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[    1.603353] Driver 'sd' needs updating - please use bus_type methods
[    1.603366] Driver 'sr' needs updating - please use bus_type methods
[    1.603570] sata_sis 0000:00:05.0: version 1.0
[    1.603596] sata_sis 0000:00:05.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    1.603605] sata_sis 0000:00:05.0: Detected SiS 182/965 chipset
[    1.603768] scsi0 : sata_sis
[    1.603916] scsi1 : sata_sis
[    1.603978] ata1: SATA max UDMA/133 cmd 0xd000 ctl 0xd400 bmdma 0xe000 irq 17
[    1.603984] ata2: SATA max UDMA/133 cmd 0xd800 ctl 0xdc00 bmdma 0xe008 irq 17
[    1.924081] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.924092] ata1: link online but device misclassified, retrying
[    1.924095] ata1: reset failed (errno=-11), retrying in 10 secs
[  11.924077] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[  11.924087] ata1: link online but device misclassified, retrying
[  11.924089] ata1: reset failed (errno=-11), retrying in 10 secs
[  21.924076] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[  21.924086] ata1: link online but device misclassified, retrying
[  21.924088] ata1: reset failed (errno=-11), retrying in 35 secs
[  56.604024] ata1: limiting SATA link speed to 1.5 Gbps
[  56.924076] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  56.924086] ata1: link online but device misclassified, device detection might fail
[  56.969376] ata1.00: ATA-7: ST3250824AS, 3.AAE, max UDMA/133
[  56.969380] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[  57.036041] ata1.00: configured for UDMA/133
[  57.356077] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[  57.356087] ata2: link online but device misclassified, retrying
[  57.356090] ata2: reset failed (errno=-11), retrying in 10 secs
[  67.356077] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[  67.356086] ata2: link online but device misclassified, retrying
[  67.356088] ata2: reset failed (errno=-11), retrying in 10 secs
[  77.356077] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[  77.356086] ata2: link online but device misclassified, retrying
[  77.356088] ata2: reset failed (errno=-11), retrying in 35 secs
[  112.036023] ata2: limiting SATA link speed to 1.5 Gbps
[  112.356077] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  112.356086] ata2: link online but device misclassified, device detection might fail
[  112.364613] ata2.00: ATA-8: ST3500320AS, SD15, max UDMA/133
[  112.364617] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[  112.380634] ata2.00: configured for UDMA/133
[  112.380798] scsi 0:0:0:0: Direct-Access    ATA      ST3250824AS      3.AA PQ: 0 ANSI: 5
[  112.380943] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[  112.380967] sd 0:0:0:0: [sda] Write Protect is off
[  112.380971] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[  112.381023] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  112.381119] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
[  112.381140] sd 0:0:0:0: [sda] Write Protect is off
[  112.381143] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[  112.381178] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  112.381183]  sda: sda1 sda2
[  112.422813] sd 0:0:0:0: [sda] Attached SCSI disk
[  112.422887] sd 0:0:0:0: Attached scsi generic sg0 type 0
[  112.422988] scsi 1:0:0:0: Direct-Access    ATA      ST3500320AS      SD15 PQ: 0 ANSI: 5
[  112.423098] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[  112.423119] sd 1:0:0:0: [sdb] Write Protect is off
[  112.423123] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[  112.423159] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  112.423225] sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[  112.423246] sd 1:0:0:0: [sdb] Write Protect is off
[  112.423249] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[  112.423284] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  112.423289]  sdb: sdb1 sdb2
[  112.471791] sd 1:0:0:0: [sdb] Attached SCSI disk
[  112.471841] sd 1:0:0:0: Attached scsi generic sg1 type 0
[  112.472426] pata_sis 0000:00:02.5: version 0.5.2
[  112.472443] pata_sis 0000:00:02.5: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[  112.472622] scsi2 : pata_sis
[  112.472708] scsi3 : pata_sis
[  112.473669] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
[  112.473672] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
[  112.636314] ata3.00: ATAPI: _NEC DVD_RW ND-4551A, 1-84, max UDMA/33
[  112.652331] ata3.00: configured for UDMA/33
[  112.809257] scsi 2:0:0:0: CD-ROM            _NEC    DVD_RW ND-4551A  1-84 PQ: 0 ANSI: 5
[  112.812405] sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[  112.812409] Uniform CD-ROM driver Revision: 3.20
[  112.812558] sr 2:0:0:0: Attached scsi CD-ROM sr0
[  112.812622] sr 2:0:0:0: Attached scsi generic sg2 type 5
[  112.812777] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[  112.812811] ehci_hcd 0000:00:03.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[  112.812850] ehci_hcd 0000:00:03.3: EHCI Host Controller
[  112.812930] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
[  112.812970] ehci_hcd 0000:00:03.3: cache line size of 128 is not supported
[  112.812988] ehci_hcd 0000:00:03.3: irq 23, io mem 0xf8003000
[  112.824022] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00
[  112.824119] usb usb1: configuration #1 chosen from 1 choice
[  112.824158] hub 1-0:1.0: USB hub found
[  112.824169] hub 1-0:1.0: 8 ports detected
[  112.824310] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[  112.824330] ohci_hcd 0000:00:03.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[  112.824344] ohci_hcd 0000:00:03.0: OHCI Host Controller
[  112.824412] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[  112.824434] ohci_hcd 0000:00:03.0: irq 20, io mem 0xf8000000
[  112.882087] usb usb2: configuration #1 chosen from 1 choice
[  112.882125] hub 2-0:1.0: USB hub found
[  112.882137] hub 2-0:1.0: 3 ports detected
[  112.882243] ohci_hcd 0000:00:03.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[  112.882256] ohci_hcd 0000:00:03.1: OHCI Host Controller
[  112.882311] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[  112.882335] ohci_hcd 0000:00:03.1: irq 21, io mem 0xf8001000
[  112.938075] usb usb3: configuration #1 chosen from 1 choice
[  112.938108] hub 3-0:1.0: USB hub found
[  112.938120] hub 3-0:1.0: 3 ports detected
[  112.938223] ohci_hcd 0000:00:03.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
[  112.938235] ohci_hcd 0000:00:03.2: OHCI Host Controller
[  112.938297] ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4
[  112.938319] ohci_hcd 0000:00:03.2: irq 22, io mem 0xf8002000
[  112.994084] usb usb4: configuration #1 chosen from 1 choice
[  112.994116] hub 4-0:1.0: USB hub found
[  112.994129] hub 4-0:1.0: 2 ports detected
[  112.994240] uhci_hcd: USB Universal Host Controller Interface driver
[  112.994321] usbcore: registered new interface driver libusual
[  112.994364] usbcore: registered new interface driver usbserial
[  112.994381] USB Serial support registered for generic
[  112.994401] usbcore: registered new interface driver usbserial_generic
[  112.994403] usbserial: USB Serial Driver core
[  112.994460] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[  112.994463] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[  112.994611] serio: i8042 KBD port at 0x60,0x64 irq 1
[  112.997080] mice: PS/2 mouse device common for all mice
[  113.008663] rtc_cmos 00:03: RTC can wake from S4
[  113.008714] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[  113.008740] rtc0: alarms up to one year, 242 bytes nvram
[  113.008817] device-mapper: uevent: version 1.0.3
[  113.008961] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[  113.009077] device-mapper: multipath: version 1.0.5 loaded
[  113.009083] device-mapper: multipath round-robin: version 1.0.0 loaded
[  113.009196] EISA: Probing bus 0 at eisa.0
[  113.009206] Cannot allocate resource for EISA slot 1
[  113.009235] EISA: Detected 0 cards.
[  113.009317] cpuidle: using governor ladder
[  113.009320] cpuidle: using governor menu
[  113.010027] TCP cubic registered
[  113.010117] NET: Registered protocol family 10
[  113.010695] lo: Disabled Privacy Extensions
[  113.011169] NET: Registered protocol family 17
[  113.011200] Bluetooth: L2CAP ver 2.11
[  113.011203] Bluetooth: L2CAP socket layer initialized
[  113.011207] Bluetooth: SCO (Voice Link) ver 0.6
[  113.011209] Bluetooth: SCO socket layer initialized
[  113.011260] Bluetooth: RFCOMM socket layer initialized
[  113.011274] Bluetooth: RFCOMM TTY layer initialized
[  113.011277] Bluetooth: RFCOMM ver 1.10
[  113.011365] Using IPI No-Shortcut mode
[  113.011487] registered taskstats version 1
[  113.011612]  Magic number: 9:681:802
[  113.011729] rtc_cmos 00:03: setting system clock to 2009-05-31 20:49:46 UTC (1243802986)
[  113.011733] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[  113.011735] EDD information not available.
[  113.012299] Freeing unused kernel memory: 532k freed
[  113.012463] Write protecting the kernel text: 4128k
[  113.012520] Write protecting the kernel read-only data: 1532k
[  113.026707] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[  113.137073] usb 1-1: new high speed USB device using ehci_hcd and address 2
[  113.388723] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[  113.388779] 8139cp 0000:00:09.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[  113.393520] 8139too Fast Ethernet driver 0.9.28
[  113.393595] 8139too 0000:00:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[  113.394972] eth0: RealTek RTL8139 at 0xe800, 00:0e:2e:86:f8:58, IRQ 17
[  113.394976] eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
[  113.414732] usb 1-1: configuration #1 chosen from 1 choice
[  113.460099] ohci1394 0000:00:0c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[  113.513041] ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16]  MMIO=[f8005000-f80057ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
[  113.629129] usb 1-8: new high speed USB device using ehci_hcd and address 4
[  113.778292] usb 1-8: configuration #1 chosen from 1 choice
[  113.792656] Initializing USB Mass Storage driver...
[  113.797629] scsi4 : SCSI emulation for USB Mass Storage devices
[  113.798695] usbcore: registered new interface driver usb-storage
[  113.798704] USB Mass Storage support registered.
[  113.798901] usb-storage: device found at 4
[  113.798905] usb-storage: waiting for device to settle before scanning
[  114.041447] PM: Starting manual resume from disk
[  114.041452] PM: Resume from partition 8:5
[  114.041455] PM: Checking hibernation image.
[  114.041650] PM: Resume from disk failed.
[  114.084039] usb 4-1: new low speed USB device using ohci_hcd and address 2
[  114.088734] kjournald starting.  Commit interval 5 seconds
[  114.088749] EXT3-fs: mounted filesystem with ordered data mode.
[  114.300387] usb 4-1: configuration #1 chosen from 1 choice
[  114.797237] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0000148500c4f581]
[  118.796611] usb-storage: device scan complete
[  118.798402] scsi 4:0:0:0: Direct-Access    Generic  STORAGE DEVICE  9144 PQ: 0 ANSI: 0
[  118.800076] scsi 4:0:0:1: Direct-Access    Generic  STORAGE DEVICE  9144 PQ: 0 ANSI: 0
[  118.801397] scsi 4:0:0:2: Direct-Access    Generic  STORAGE DEVICE  9144 PQ: 0 ANSI: 0
[  118.802764] scsi 4:0:0:3: Direct-Access    Generic  STORAGE DEVICE  9144 PQ: 0 ANSI: 0
[  118.804745] scsi 4:0:0:4: Direct-Access    Generic  STORAGE DEVICE  9144 PQ: 0 ANSI: 0
[  118.806702] sd 4:0:0:0: [sdc] Attached SCSI removable disk
[  118.806826] sd 4:0:0:0: Attached scsi generic sg3 type 0
[  118.808192] sd 4:0:0:1: [sdd] Attached SCSI removable disk
[  118.808315] sd 4:0:0:1: Attached scsi generic sg4 type 0
[  118.809809] sd 4:0:0:2: [sde] Attached SCSI removable disk
[  118.809927] sd 4:0:0:2: Attached scsi generic sg5 type 0
[  118.811262] sd 4:0:0:3: [sdf] Attached SCSI removable disk
[  118.811358] sd 4:0:0:3: Attached scsi generic sg6 type 0
[  118.813402] sd 4:0:0:4: [sdg] Attached SCSI removable disk
[  118.813551] sd 4:0:0:4: Attached scsi generic sg7 type 0
[  118.884333] udev: starting version 141
[  119.051186] usbcore: registered new interface driver hiddev
[  119.057636] input: Logitech USB Optical Mouse as /devices/pci0000:00/0000:00:03.2/usb4/4-1/4-1:1.0/input/input4
[  119.090179] generic-usb 0003:046D:C018.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-0000:00:03.2-1/input0
[  119.090229] usbcore: registered new interface driver usbhid
[  119.090277] usbhid: v2.6:USB HID core driver
[  119.220534] parport_pc 00:07: reported by Plug and Play ACPI
[  119.220609] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[  119.353368] cfg80211: Calling CRDA to update world regulatory domain
[  119.368808] input: PC Speaker as /devices/platform/pcspkr/input/input5
[  119.783989] cfg80211: World regulatory domain updated:
[  119.783994] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[  119.783998] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  119.784001] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[  119.784004] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[  119.784007] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  119.784010] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[  119.887902] ppdev: user-space parallel port driver
[  120.070429] Intel ICH 0000:00:02.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[  120.248176] phy0: Selected rate control algorithm 'pid'
[  120.285141] Registered led device: rt73usb-phy0:radio
[  120.285224] Registered led device: rt73usb-phy0:assoc
[  120.285303] Registered led device: rt73usb-phy0:quality
[  120.285846] usbcore: registered new interface driver rt73usb
[  120.392025] intel8x0_measure_ac97_clock: measured 53921 usecs
[  120.392029] intel8x0: clocking to 48000
[  120.575961] lp0: using parport0 (interrupt-driven).
[  120.691062] Adding 3004112k swap on /dev/sda5.  Priority:-1 extents:1 across:3004112k
[  121.246133] EXT3 FS on sda1, internal journal
[  122.463530] type=1505 audit(1243802995.948:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2097
[  122.517728] type=1505 audit(1243802996.004:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2101
[  122.517939] type=1505 audit(1243802996.004:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2101
[  122.518000] type=1505 audit(1243802996.004:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2101
[  122.518056] type=1505 audit(1243802996.004:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2101
[  122.672318] type=1505 audit(1243802996.160:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2106
[  122.672643] type=1505 audit(1243802996.160:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2106
[  122.707536] type=1505 audit(1243802996.192:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2110
[  124.927873] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[  124.927879] Bluetooth: BNEP filters: protocol multicast
[  124.949707] Bridge firewalling registered
[  130.512580] eth0: link down
[  130.512872] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  130.514401] rt73usb 1-1:1.0: firmware: requesting rt73.bin
[  130.636554] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  188.609862] wlan0: authenticate with AP 00:0f:cb:a9:d4:d2
[  188.611222] wlan0: authenticated
[  188.611229] wlan0: associate with AP 00:0f:cb:a9:d4:d2
[  188.613353] wlan0: RX AssocResp from 00:0f:cb:a9:d4:d2 (capab=0x471 status=0 aid=1)
[  188.613359] wlan0: associated
[  188.621522] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  199.076036] wlan0: no IPv6 routers present

Pero non so interpretare questo risultato.

Grazie
Alexx
Prode Principiante
Messaggi: 205
Iscrizione: sabato 1 novembre 2008, 21:36

Re: [Boot] problema avvio jaunty

Messaggio da Alexx »

ciao,

ti fa una cronologia temporale.
la prima parte e' il tempo, dopo ti descrive che cosa fa nel mentre carica.
Per vedere se ci sono anomalie scorri fino a che non trovi dei lassi di tempo lunghi, guarda qui:

[    77.356088] ata2: reset failed (errno=-11), retrying in 35 secs
[  112.036023] ata2: limiting SATA link speed to 1.5 Gbps

sembra che inciampi e ci riprova dopo 35 secondi (112-77=35), poi va liscio.
non so' da cosa possa dipendere.
prova a googlare.

[  130.636554] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  188.609862] wlan0: authenticate with AP 00:0f:cb:a9:d4:d2
[  188.611222] wlan0: authenticated

resta un po' a pensare sulla wlan, ma questo dovrebbe essere nei canoni.
A me va veloce perchè ho messo un ip statico e si aggancia al volo senza tante smancerie  ;)

ciao


ciao
Ultima modifica di Alexx il giovedì 18 giugno 2009, 12:09, modificato 1 volta in totale.
Avatar utente
manuelik
Prode Principiante
Messaggi: 85
Iscrizione: domenica 8 giugno 2008, 16:35

Re: [Boot] problema avvio jaunty

Messaggio da manuelik »

Grazie della risposta mi sa che dipende proprio dall'ip xche da quando ho rifatto le impostazioni sono in dhcp provero a mettere un ip statico grazie 1000 ancora  (good)


ciao
Manuel
Scrivi risposta

Ritorna a “Driver e periferiche”

Chi c’è in linea

Visualizzano questa sezione: Google [Bot] e 9 ospiti