Bisogna fare questa prova; da terminale dai questi comandi:Musashi73 [url=http://forum.ubuntu-it.org/viewtopic.php?p=4827490#p4827490][img]http://forum.ubuntu-it.org/images/icons/icona-cita.gif[/img][/url] ha scritto:C'è un modo per provare e capire se funziona?
Codice: Seleziona tutto
sudo apt-get purge bcmwl-kernel-source broadcom-sta-common broadcom-sta-source
Codice: Seleziona tutto
sudo apt-get install b43-fwcutter firmware-b43-installer
Codice: Seleziona tutto
Support for cores revision 0x17 and 0x18 disabled by module param allhwsupport=0. Try b43.allhwsupport=1
Codice: Seleziona tutto
sudo ifconfig wlan0 down
Codice: Seleziona tutto
sudo modprobe -r b43
Codice: Seleziona tutto
sudo modprobe b43
Codice: Seleziona tutto
sudo ifconfig wlan0 up
Codice: Seleziona tutto
lspci -nn | grep -i net
03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 07)
04:00.0 Network controller [0280]: Qualcomm Atheros AR9485 Wireless Network Adapter [168c:0032] (rev 01)
Codice: Seleziona tutto
sudo lshw -C network:
*-network
description: Ethernet interface
product: RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
vendor: Realtek Semiconductor Co., Ltd.
physical id: 0
bus info: pci@0000:03:00.0
logical name: enp3s0
version: 07
serial: 60:a4:4c:7d:14:4d
size: 10Mbit/s
capacity: 1Gbit/s
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8168e-3_0.0.4 03/27/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s
resources: irq:31 ioport:d000(size=256) memory:d00fb000-d00fbfff memory:d0000000-d0003fff
*-network
description: Wireless interface
product: AR9485 Wireless Network Adapter
vendor: Qualcomm Atheros
physical id: 0
bus info: pci@0000:04:00.0
logical name: wlp4s0
version: 01
serial: 2c:d0:5a:5a:11:09
width: 64 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical wireless
configuration: broadcast=yes driver=ath9k driverversion=4.2.0-25-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn
resources: irq:17 memory:ff900000-ff97ffff memory:ff980000-ff98ffff
*-network DISABLED
description: Ethernet interface
physical id: 1
logical name: wwx582c80139263
serial: 58:2c:80:13:92:63
capabilities: ethernet physical
configuration: broadcast=yes driver=huawei_cdc_ncm driverversion=22-Aug-2005 firmware=Huawei CDC NCM device link=no multicast=yes
Codice: Seleziona tutto
sudo gedit /etc/kismet/kismet.confCodice: Seleziona tutto
ncsource=wlan0:name=qualcommCodice: Seleziona tutto
sudo gedit /etc/kismet/kismet.conf
Codice: Seleziona tutto
ncsource=wlan0:name=qualcomm
Codice: Seleziona tutto
ncsource=wlp4s0:name=atheros
Codice: Seleziona tutto
sudo kismet
Per utilizzare kismet so che devo impostare la mia scheda wireless in monitor mode e questo l'ho fatto, quando l'ho lanciato però era attiva anche una connessione con chiavetta usb. Va bene così oppure deve lavorare solo la wireless in monitor mode? Codice: Seleziona tutto
cat /etc/kismet/kismet.conf
Codice: Seleziona tutto
cat /etc/kismet/kismet.conf
# Kismet config file
# Most of the "static" configs have been moved to here -- the command line
# config was getting way too crowded and cryptic. We want functionality,
# not continually reading --help!
# Version of Kismet config
version=2009-newcore
# Name of server (Purely for organizational purposes)
# If commented out, defaults to host name of system
# servername=Kismet Server
# Prefix of where we log (as used in the logtemplate later)
# logprefix=/some/path/to/logs
# Do we process the contents of data frames? If this is enabled, data
# frames will be truncated to the headers only immediately after frame type
# detection. This will disable IP detection, etc, however it is likely
# safer (and definitely more polite) if monitoring networks you do not own.
# hidedata=true
# Do we allow plugins to be used? This will load plugins from the system
# and user plugin directiories when set to true (See the README for the default
# plugin locations).
allowplugins=true
# See the README for full information on the new source format
# ncsource=interface:options
# for example:
# ncsource=wlan0
# ncsource=wifi0:type=madwifi
# ncsource=wlan0:name=intel,hop=false,channel=11
ncsource=wlp4s0:name=atheros
# Comma-separated list of sources to enable. This is only needed if you defined
# multiple sources and only want to enable some of them. By default, all defined
# sources are enabled.
# For example, if sources with name=prismsource and name=ciscosource are defined,
# and you only want to enable those two:
# enablesources=prismsource,ciscosource
# Control which channels we like to spend more time on. By default, the list
# of channels is pulled from the driver automatically. By setting preferred channels,
# if they are present in the channel list, they'll be set with a timing delay so that
# more time is spent on them. Since 1, 6, 11 are the common default channels, it makes
# sense to spend more time monitoring them.
# For finer control, see further down in the config for the channellist= directives.
preferredchannels=1,6,11
# How many channels per second do we hop? (1-10)
channelvelocity=3
# By setting the dwell time for channel hopping we override the channelvelocity
# setting above and dwell on each channel for the given number of seconds.
#channeldwell=10
# Channels are defined as:
# channellist=name:ch1,ch2,ch3
# or
# channellist=name:range-start-end-width-offset,ch,range,ch,...
#
# Channels may be a numeric channel or a frequency
#
# Channels may specify an additional wait period. For common default channels,
# an additional wait period can be useful. Wait periods delay for that number
# of times per second - so a configuration hopping 10 times per second with a
# channel of 6:3 would delay 3/10ths of a second on channel 6.
#
# Channel lists may have up to 256 channels and ranges (combined). For power
# users scanning more than 256 channels with a single card, ranges must be used.
#
# Ranges are meant for "power users" who wish to define a very large number of
# channels. A range may specify channels or frequencies, and will automatically
# sort themselves to cover channels in a non-overlapping fashion. An example
# range for the normal 802.11b/g spectrum would be:
#
# range-1-11-3-1
#
# which indicates starting at 1, ending at 11, a channel width of 3 channels,
# incrementing by one. A frequency based definition would be:
#
# range-2412-2462-22-5
#
# since 11g channels are 22 mhz wide and 5 mhz apart.
#
# Ranges have the flaw that they cannot be shared between sources in a non-overlapping
# way, so multiple sources using the same range may hop in lockstep with each other
# and duplicate the coverage.
#
# channellist=demo:1:3,6:3,11:3,range-5000-6000-20-10
# Default channel lists
# These channel lists MUST BE PRESENT for Kismet to work properly. While it is
# possible to change these, it is not recommended. These are used when the supported
# channel list can not be found for the source; to force using these instead of
# the detected supported channels, override with channellist= in the source defintion
#
# IN GENERAL, if you think you want to modify these, what you REALLY want to do is
# copy them and use channellist= in the packet source.
channellist=IEEE80211b:1:3,6:3,11:3,2,7,3,8,4,9,5,10
channellist=IEEE80211a:36,40,44,48,52,56,60,64,149,153,157,161,165
channellist=IEEE80211ab:1:3,6:3,11:3,2,7,3,8,4,9,5,10,36,40,44,48,52,56,60,64,149,153,157,161,165
# Client/server listen config
listen=tcp://127.0.0.1:2501
# People allowed to connect, comma seperated IP addresses or network/mask
# blocks. Netmasks can be expressed as dotted quad (/255.255.255.0) or as
# numbers (/24)
allowedhosts=127.0.0.1
# Maximum number of concurrent GUI's
maxclients=5
# Maximum backlog before we start throwing out or killing clients. The
# bigger this number, the more memory and the more power it will use.
maxbacklog=5000
# Server + Drone config options. To have a Kismet server export live packets
# as if it were a drone, uncomment these.
# dronelisten=tcp://127.0.0.1:3501
# droneallowedhosts=127.0.0.1
# dronemaxclients=5
# droneringlen=65535
# OUI file, expected format 00:11:22<tab>manufname
# IEEE OUI file used to look up manufacturer info. We default to the
# wireshark one since most people have that.
ouifile=/etc/manuf
ouifile=/usr/share/wireshark/wireshark/manuf
ouifile=/usr/share/wireshark/manuf
ouifile=/Applications/Wireshark.app/Contents/Resources/share/wireshark/manuf
# Do we have a GPS?
gps=true
# Do we use a locally serial attached GPS, or use a gpsd server, or
# use a fixed virtual gps?
# (Pick only one)
gpstype=gpsd
# Host:port that GPSD is running on. This can be localhost OR remote!
gpshost=localhost:2947
# gpstype=serial
# What serial device do we look for the GPS on?
# gpsdevice=/dev/rfcomm0
# gpstype=virtual
# gpsposition=100,-50
# gpsaltitude=1234
# Do we lock the mode? This overrides coordinates of lock "0", which will
# generate some bad information until you get a GPS lock, but it will
# fix problems with GPS units with broken NMEA that report lock 0
gpsmodelock=false
# Do we try to reconnect if we lose our link to the GPS, or do we just
# let it die and be disabled?
gpsreconnect=true
# Do we export packets over tun/tap virtual interfaces?
tuntap_export=false
# What virtual interface do we use
tuntap_device=kistap0
# Packet filtering options:
# filter_tracker - Packets filtered from the tracker are not processed or
# recorded in any way.
# filter_export - Controls what packets influence the exported CSV, network,
# xml, gps, etc files.
# All filtering options take arguments containing the type of address and
# addresses to be filtered. Valid address types are 'ANY', 'BSSID',
# 'SOURCE', and 'DEST'. Filtering can be inverted by the use of '!' before
# the address. For example,
# filter_tracker=ANY(!"00:00:DE:AD:BE:EF")
# has the same effect as the previous mac_filter config file option.
# filter_tracker=...
# filter_dump=...
# filter_export=...
# filter_netclient=...
# Alerts to be reported and the throttling rates.
# alert=name,throttle/unit,burst
# The throttle/unit describes the number of alerts of this type that are
# sent per time unit. Valid time units are second, minute, hour, and day.
# Burst describes the number of alerts sent before throttling takes place.
# For example:
# alert=FOO,10/min,5
# Would allow 5 alerts through before throttling is enabled, and will then
# limit the number of alerts to 10 per minute.
# A throttle rate of 0 disables throttling of the alert.
# See the README for a list of alert types.
alert=ADHOCCONFLICT,5/min,1/sec
alert=AIRJACKSSID,5/min,1/sec
alert=APSPOOF,10/min,1/sec
alert=BCASTDISCON,5/min,2/sec
alert=BSSTIMESTAMP,5/min,1/sec
alert=CHANCHANGE,5/min,1/sec
alert=CRYPTODROP,5/min,1/sec
alert=DISASSOCTRAFFIC,10/min,1/sec
alert=DEAUTHFLOOD,5/min,2/sec
alert=DEAUTHCODEINVALID,5/min,1/sec
alert=DISCONCODEINVALID,5/min,1/sec
alert=DHCPNAMECHANGE,5/min,1/sec
alert=DHCPOSCHANGE,5/min,1/sec
alert=DHCPCLIENTID,5/min,1/sec
alert=DHCPCONFLICT,10/min,1/sec
alert=NETSTUMBLER,5/min,1/sec
alert=LUCENTTEST,5/min,1/sec
alert=LONGSSID,5/min,1/sec
alert=MSFBCOMSSID,5/min,1/sec
alert=MSFDLINKRATE,5/min,1/sec
alert=MSFNETGEARBEACON,5/min,1/sec
alert=NULLPROBERESP,5/min,1/sec
#alert=PROBENOJOIN,5/min,1/sec
# Controls behavior of the APSPOOF alert. SSID may be a literal match (ssid=) or
# a regex (ssidregex=) if PCRE was available when kismet was built. The allowed
# MAC list must be comma-separated and enclosed in quotes if there are multiple
# MAC addresses allowed. MAC address masks are allowed.
apspoof=Foo1:ssidregex="(?i:foobar)",validmacs=00:11:22:33:44:55
apspoof=Foo2:ssid="Foobar",validmacs="00:11:22:33:44:55,aa:bb:cc:dd:ee:ff"
# Known WEP keys to decrypt, bssid,hexkey. This is only for networks where
# the keys are already known, and it may impact throughput on slower hardware.
# Multiple wepkey lines may be used for multiple BSSIDs.
# wepkey=00:DE:AD:C0:DE:00,FEEDFACEDEADBEEF01020304050607080900
# Is transmission of the keys to the client allowed? This may be a security
# risk for some. If you disable this, you will not be able to query keys from
# a client.
allowkeytransmit=true
# How often (in seconds) do we write all our data files (0 to disable)
writeinterval=300
# Do we use sound?
# Not to be confused with GUI sound parameter, this controls wether or not the
# server itself will play sound. Primarily for headless or automated systems.
enablesound=false
# Path to sound player
soundbin=play
sound=newnet,true
sound=newcryptnet,true
sound=packet,true
sound=gpslock,true
sound=gpslost,true
sound=alert,true
# Does the server have speech? (Again, not to be confused with the GUI's speech)
enablespeech=false
# Binary used for speech (if not in path, full path must be specified)
speechbin=flite
# Specify raw or festival; Flite (and anything else that doesn't need formatting
# around the string to speak) is 'raw', festival requires the string be wrapped in
# SayText("...")
speechtype=raw
# How do we speak? Valid options:
# speech Normal speech
# nato NATO spellings (alpha, bravo, charlie)
# spell Spell the letters out (aye, bee, sea)
speechencoding=nato
speech=new,"New network detected s.s.i.d. %1 channel %2"
speech=alert,"Alert %1"
speech=gpslost,"G.P.S. signal lost"
speech=gpslock,"G.P.S. signal O.K."
# How many alerts do we backlog for new clients? Only change this if you have
# a -very- low memory system and need those extra bytes, or if you have a high
# memory system and a huge number of alert conditions.
alertbacklog=50
# File types to log, comma seperated. Built-in log file types:
# alert Text file of alerts
# gpsxml XML per-packet GPS log
# nettxt Networks in text format
# netxml Networks in XML format
# pcapdump tcpdump/wireshark compatible pcap log file
# string All strings seen (increases CPU load)
logtypes=pcapdump,gpsxml,netxml,nettxt,alert
# Format of the pcap dump (PPI or 80211)
pcapdumpformat=ppi
# pcapdumpformat=80211
# Default log title
logdefault=Kismet
# logtemplate - Filename logging template.
# This is, at first glance, really nasty and ugly, but you'll hardly ever
# have to touch it so don't complain too much.
#
# %p is replaced by the logging prefix + '/'
# %n is replaced by the logging instance name
# %d is replaced by the starting date as Mon-DD-YYYY
# %D is replaced by the current date as YYYYMMDD
# %t is replaced by the starting time as HH-MM-SS
# %i is replaced by the increment log in the case of multiple logs
# %l is replaced by the log type (pcapdump, strings, etc)
# %h is replaced by the home directory
logtemplate=%p%n-%D-%t-%i.%l
# Where state info, etc, is stored. You shouldnt ever need to change this.
# This is a directory.
configdir=%h/.kismet/
Visualizzano questa sezione: 0 utenti iscritti e 5 ospiti