[Wireless] nessuna connessione alla rete hp pavilion zv5000
[Wireless] nessuna connessione alla rete hp pavilion zv5000
Ciao a tutti,
sono un felice utilizzatore di Ubuntu 9.04 sul mio desktop. Va veramente a meraviglia, ormai windows lo apro raramente e solo per giocare.
Ho installato Ubuntu anche sul portatile: un vecchio ma ancora discreto HP Pavilion zv5000.
Installazione ok e anche riconoscimento hardware. Ho fatto tutti gli aggiornamenti e tra i driver hardware il sistema mi ha anche installato il driver per la scheda di rete wireless che di default non trova.
La scheda funziona correttamente: sente la rete ma non c'è verso di collegarla. Immetto la chiave di rete e non va. Anche se la elimino e quindi tolgo qualsiasi protezione non ne vuole sapere di collegarsi.
Non mi dite che per questa cavolata devo ritornare a windows!!
Aiuto please!!
sono un felice utilizzatore di Ubuntu 9.04 sul mio desktop. Va veramente a meraviglia, ormai windows lo apro raramente e solo per giocare.
Ho installato Ubuntu anche sul portatile: un vecchio ma ancora discreto HP Pavilion zv5000.
Installazione ok e anche riconoscimento hardware. Ho fatto tutti gli aggiornamenti e tra i driver hardware il sistema mi ha anche installato il driver per la scheda di rete wireless che di default non trova.
La scheda funziona correttamente: sente la rete ma non c'è verso di collegarla. Immetto la chiave di rete e non va. Anche se la elimino e quindi tolgo qualsiasi protezione non ne vuole sapere di collegarsi.
Non mi dite che per questa cavolata devo ritornare a windows!!
Aiuto please!!
Ultima modifica di sgm il venerdì 17 luglio 2009, 19:39, modificato 1 volta in totale.
- nico@nico
- Entusiasta Emergente

- Messaggi: 1372
- Iscrizione: venerdì 31 ottobre 2008, 17:51
- Località: torino
- Contatti:
Re: [Wireless] nessuna connessione alla rete
hai provato a installare wicd al posto di network manager?
ma hulk era marcato con GFP?
Re: [Wireless] nessuna connessione alla rete
nono aspetta un attimo!!nico@nico ha scritto: hai provato a installare wicd al posto di network manager?
Secondo me sono io che sbaglio qualcosa: quando mi chiede la chiave di rete mi si apre anche la richiesta di impostare una password per il portachiavi!
Mo...è vero che sono un felice utente di Ubuntu ma non sono espetissimo: che cacchio è il portachiavi?
Secondo me la soluzione è banale. Sbaglio qualcosa a livello di chiave di rete e portachiavi.
- nico@nico
- Entusiasta Emergente

- Messaggi: 1372
- Iscrizione: venerdì 31 ottobre 2008, 17:51
- Località: torino
- Contatti:
Re: [Wireless] nessuna connessione alla rete
in poche parole all'interno del portachiavi rimangono delle password (tra cui quella della chiave di rete) cui puoi accedere mediant un'unica password, cioè quella che imposti per il portachiavi.
ma hulk era marcato con GFP?
Re: [Wireless] nessuna connessione alla rete
adesso non sente neanche piu la rete wireless neanche con wicd come suggerito
che paranoia!
che paranoia!
- nico@nico
- Entusiasta Emergente

- Messaggi: 1372
- Iscrizione: venerdì 31 ottobre 2008, 17:51
- Località: torino
- Contatti:
Re: [Wireless] nessuna connessione alla rete
lo no wireless extensions.nico@nico ha scritto: mi posti "iwconfig"
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11b ESSID:""
Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=20 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
pan0 no wireless extensions.
da qui sembra in effetti che non veda neanche piu l'hardware >:( ::) :-\ :'(
- nico@nico
- Entusiasta Emergente

- Messaggi: 1372
- Iscrizione: venerdì 31 ottobre 2008, 17:51
- Località: torino
- Contatti:
Re: [Wireless] nessuna connessione alla rete
http://forum.ubuntu-it.org/viewtopic.php?t=47690
segui questa guida, non dovresti avere problemi
mi raccomando fammi sapere
segui questa guida, non dovresti avere problemi
mi raccomando fammi sapere
ma hulk era marcato con GFP?
Re: [Wireless] nessuna connessione alla rete
Niente non va.nico@nico ha scritto: http://forum.ubuntu-it.org/viewtopic.php?t=47690
segui questa guida, non dovresti avere problemi
mi raccomando fammi sapere![]()
Ho seguito la guida in maniera maniacale. Ora la rete la sente ma non si connette neanche se tolgo la passkey.
Arriva all'acquisizione dell'indirizzo ip e poi si disconnette.
Mentre con la passkey dice validating authentication e poi si ferma.
Boh...su windows funziona normalmente!!
Preciso che ho fastweb
Ultima modifica di sgm il venerdì 17 luglio 2009, 17:31, modificato 1 volta in totale.
Re: [Wireless] nessuna connessione alla rete
mi domando se c'è qualcuno che ha lo stesso portatile e naviga tranquillamente in wireless!!
Ho fatto un po di ricerche sul forum e sembra che le versioni precedenti di Ubuntu non supportassero l'hardware tanto è vero che c'è chi ha anche usato ndiswrapper.
Con al versione 9.04 la scheda wifi viene riconosciuta in automatico e sembra funzionare ma non si connette!!
Mah...aspetto fiducioso qualche consiglio!
saluti
Ho fatto un po di ricerche sul forum e sembra che le versioni precedenti di Ubuntu non supportassero l'hardware tanto è vero che c'è chi ha anche usato ndiswrapper.
Con al versione 9.04 la scheda wifi viene riconosciuta in automatico e sembra funzionare ma non si connette!!
Mah...aspetto fiducioso qualche consiglio!
saluti
- [lost]-Divilinux
- Imperturbabile Insigne

- Messaggi: 3774
- Iscrizione: giovedì 12 giugno 2008, 13:06
- Località: Ipioca - Maceio - Alagoas - Brasil
- Contatti:
Re: [Wireless] nessuna connessione alla rete hp pavilion zv5000
Noi aspettiamo qualche informazione in piu' perche' con "non sente" e "non vede" e' veramente difficile capire dove sia il problema
Sarebbe interessante sapere di che scheda si tratta. Posta:
Al di la dei vari network manager, per escudere che il problema derivi da quello, connettiti da terminale
Se usi il dhcp ed una chiave wep
- CHIAVE=chiave wep
- ESSID= tuo essid
da qui sembra in effetti che non veda neanche piu l'hardware
No, qui semplicemente si vede che non c'e' nessun access point associato. Se fosse un problema di mancanza dei driver non ci sarebbe wlan0 nell'output di iwconfig.wlan0 IEEE 802.11b ESSID:""
Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=20 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Sarebbe interessante sapere di che scheda si tratta. Posta:
Codice: Seleziona tutto
lspci
lsmodSe usi il dhcp ed una chiave wep
Codice: Seleziona tutto
sudo iwconfig wlan0 mode managed key CHIAVE essid ESSID
sudo dhclient wlan0- ESSID= tuo essid
questione di seedings...
Re: [Wireless] nessuna connessione alla rete hp pavilion zv5000
eh lo so che voi vi aspettate qualche informazione in più e vi ringrazio dei suggerimenti che mi date, solo che da niubbo quale sono se non me le chiedete non so che informazioni darvi.[lost]-Divilinux ha scritto: Noi aspettiamo qualche informazione in piu' perche' con "non sente" e "non vede" e' veramente difficile capire dove sia il problema
da qui sembra in effetti che non veda neanche piu l'hardwareNo, qui semplicemente si vede che non c'e' nessun access point associato. Se fosse un problema di mancanza dei driver non ci sarebbe wlan0 nell'output di iwconfig.wlan0 IEEE 802.11b ESSID:""
Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=20 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Sarebbe interessante sapere di che scheda si tratta. Posta:
Al di la dei vari network manager, per escudere che il problema derivi da quello, connettiti da terminaleCodice: Seleziona tutto
lspci lsmod
Se usi il dhcp ed una chiave wep
- CHIAVE=chiave wepCodice: Seleziona tutto
sudo iwconfig wlan0 mode managed key CHIAVE essid ESSID sudo dhclient wlan0
- ESSID= tuo essid
comunque detto questo da quello che ho potuto capire da installazione pulita del sistema operativo la scheda è riconosciuta. All'inizio non sente la rete perche è disattivata di default!
Se vado in sistema-amministrazione-driver hardware mi fa installare una sorta di driver per attivarla e disattivarla. Infatti subito dopo posso attivarla con l'apposito tasto sul pc e rileva la mia rete. Poi da qui buio: non c'è verso di farla connettere ne da terminale e ne da interfaccia grafica. Ne con network-manager e ne con wicd.
Comunque, ecco le info che volevi:
lspci: Broadcom Corporation BCM4303 802.11b Wireless LAN Controller (rev 02)
lsmod:
Module Size Used by
rfkill_input 12800 0
binfmt_misc 16776 1
bridge 56340 0
stp 10500 1 bridge
bnep 20224 2
lp 17156 0
pcmcia 44748 0
arc4 9856 2
ecb 10752 2
snd_intel8x0 37532 3
snd_ac97_codec 112292 1 snd_intel8x0
ac97_bus 9856 1 snd_ac97_codec
snd_pcm_oss 46336 0
snd_mixer_oss 22656 1 snd_pcm_oss
snd_pcm 82948 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
b43legacy 127004 0
snd_seq_dummy 10756 0
snd_seq_oss 37760 0
mac80211 217464 1 b43legacy
snd_seq_midi 14336 0
snd_rawmidi 29696 1 snd_seq_midi
snd_seq_midi_event 15104 2 snd_seq_oss,snd_seq_midi
cfg80211 38288 1 mac80211
snd_seq 56880 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 29704 2 snd_pcm,snd_seq
snd_seq_device 14988 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
joydev 18496 0
yenta_socket 32396 2
rsrc_nonstatic 19328 1 yenta_socket
led_class 12036 1 b43legacy
amd64_agp 18184 1
nvidia 4712596 32
pcmcia_core 43540 3 pcmcia,yenta_socket,rsrc_nonstatic
input_polldev 11912 1 b43legacy
k8temp 12416 0
ppdev 15620 0
snd 62628 16 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
soundcore 15200 1 snd
snd_page_alloc 16904 2 snd_intel8x0,snd_pcm
agpgart 42696 2 amd64_agp,nvidia
i2c_nforce2 14980 0
pcspkr 10496 0
shpchp 40212 0
psmouse 61972 0
serio_raw 13316 0
video 25360 0
parport_pc 40100 1
parport 42220 3 lp,ppdev,parport_pc
output 11008 1 video
b44 35984 0
ohci1394 38576 0
ssb 41220 2 b43legacy,b44
8139too 32128 0
8139cp 27776 0
mii 13312 3 b44,8139too,8139cp
ieee1394 94660 1 ohci1394
fbcon 46112 0
tileblit 10752 1 fbcon
font 16384 1 fbcon
bitblit 13824 1 fbcon
softcursor 9984 1 bitblit
scusa la confusione ma sto su un altro pc
grazie
- [lost]-Divilinux
- Imperturbabile Insigne

- Messaggi: 3774
- Iscrizione: giovedì 12 giugno 2008, 13:06
- Località: Ipioca - Maceio - Alagoas - Brasil
- Contatti:
Re: [Wireless] nessuna connessione alla rete hp pavilion zv5000
è una broadcom che sta utilizzando i driver b43_leagcy.
Posta anche l'output di iwconfig
Posta anche l'output di iwconfig
questione di seedings...
Re: [Wireless] nessuna connessione alla rete hp pavilion zv5000
lo no wireless extensions.[lost]-Divilinux ha scritto: è una broadcom che sta utilizzando i driver b43_leagcy.
Posta anche l'output di iwconfig
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11b ESSID:""
Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated
Tx-Power=20 dBm
Retry min limit:7 RTS thr:off Fragment thr=2352 B
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
pan0 no wireless extensions.
- [lost]-Divilinux
- Imperturbabile Insigne

- Messaggi: 3774
- Iscrizione: giovedì 12 giugno 2008, 13:06
- Località: Ipioca - Maceio - Alagoas - Brasil
- Contatti:
Re: [Wireless] nessuna connessione alla rete hp pavilion zv5000
Scusa non avevo letto che iwconfig l'avevi già postato.
È solo un problema di configurazione, a meno che i driver non siano bacati..
Per scoprire eventuali problemi con la scheda basta postare l'output di dmesg.
Per connetterti da terminale, ed escludere problemi col NM o con WICD, togli la chiave di protezione e imposta il dhcp (viene piu facile fare il test)
Poi lanci da terminale
È solo un problema di configurazione, a meno che i driver non siano bacati..
Per scoprire eventuali problemi con la scheda basta postare l'output di dmesg.
Per connetterti da terminale, ed escludere problemi col NM o con WICD, togli la chiave di protezione e imposta il dhcp (viene piu facile fare il test)
Poi lanci da terminale
Codice: Seleziona tutto
sudo iwconfig wlan0 mode managed essid TUO_ESSID key off
sudo dhclient wlan0questione di seedings...
Re: [Wireless] nessuna connessione alla rete hp pavilion zv5000
sono su un altro pc. Stasera ti posto il risultato del comando dsmeg.[lost]-Divilinux ha scritto: Scusa non avevo letto che iwconfig l'avevi già postato.
È solo un problema di configurazione, a meno che i driver non siano bacati..
Per scoprire eventuali problemi con la scheda basta postare l'output di dmesg.
Per connetterti da terminale, ed escludere problemi col NM o con WICD, togli la chiave di protezione e imposta il dhcp (viene piu facile fare il test)
Poi lanci da terminale
Codice: Seleziona tutto
sudo iwconfig wlan0 mode managed essid TUO_ESSID key off sudo dhclient wlan0
In ogni caso anche con i comandi da terminale per impostare i parametri della rete non c'è verso di farla connetere.
Toglietemi una curiosità: in qualche modo si può evitare che Ubuntu utilizzi i suoi driver (supponendo che non funzionino a dovere) e caricare quelli di windows con ndiswrapper?
Se si come si fa?
- [lost]-Divilinux
- Imperturbabile Insigne

- Messaggi: 3774
- Iscrizione: giovedì 12 giugno 2008, 13:06
- Località: Ipioca - Maceio - Alagoas - Brasil
- Contatti:
Re: [Wireless] nessuna connessione alla rete hp pavilion zv5000
Per un problema di configurazione lascerei tutto cosi.
Altrimenti devi mettere in blacklist i b43 ed installare ndiswrapper. Ndiswrapper utilizza i driver di windows ma a prestazioni ed opzioni faresti un grosso passo indietro (fosse solo per la qualita' di segnale)
Altrimenti devi mettere in blacklist i b43 ed installare ndiswrapper. Ndiswrapper utilizza i driver di windows ma a prestazioni ed opzioni faresti un grosso passo indietro (fosse solo per la qualita' di segnale)
questione di seedings...
Re: [Wireless] nessuna connessione alla rete hp pavilion zv5000
di seguito l'output del comando dmesg come da te richiesto:
[ 1.137644] pci 0000:00:08.0: reg 20 io port: [0x2080-0x208f]
[ 1.137855] pci 0000:02:00.0: reg 10 32bit mmio: [0xe0108000-0xe01087ff]
[ 1.137865] pci 0000:02:00.0: reg 14 32bit mmio: [0xe0100000-0xe0103fff]
[ 1.137898] pci 0000:02:00.0: supports D1 D2
[ 1.137903] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
[ 1.137910] pci 0000:02:00.0: PME# disabled
[ 1.137942] pci 0000:02:01.0: reg 10 io port: [0x7000-0x70ff]
[ 1.137952] pci 0000:02:01.0: reg 14 32bit mmio: [0xe0108800-0xe01088ff]
[ 1.137984] pci 0000:02:01.0: supports D1 D2
[ 1.137989] pci 0000:02:01.0: PME# supported from D1 D2 D3hot D3cold
[ 1.137995] pci 0000:02:01.0: PME# disabled
[ 1.138018] pci 0000:02:02.0: reg 10 32bit mmio: [0xe0104000-0xe0105fff]
[ 1.138077] pci 0000:02:04.0: reg 10 32bit mmio: [0xe0106000-0xe0106fff]
[ 1.138090] pci 0000:02:04.0: supports D1 D2
[ 1.138094] pci 0000:02:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.138101] pci 0000:02:04.0: PME# disabled
[ 1.138135] pci 0000:02:04.1: reg 10 32bit mmio: [0xe0107000-0xe0107fff]
[ 1.138148] pci 0000:02:04.1: supports D1 D2
[ 1.138152] pci 0000:02:04.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.138159] pci 0000:02:04.1: PME# disabled
[ 1.138190] pci 0000:02:04.2: reg 10 io port: [0x7400-0x743f]
[ 1.138266] pci 0000:00:0a.0: bridge io port: [0x3000-0x7fff]
[ 1.138273] pci 0000:00:0a.0: bridge 32bit mmio: [0xe0100000-0xe17fffff]
[ 1.138353] pci 0000:01:00.0: reg 10 32bit mmio: [0xe2000000-0xe2ffffff]
[ 1.138364] pci 0000:01:00.0: reg 14 32bit mmio: [0xf0000000-0xf7ffffff]
[ 1.138374] pci 0000:01:00.0: reg 18 32bit mmio: [0xf8000000-0xf807ffff]
[ 1.138399] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 1.138461] pci 0000:00:0b.0: bridge 32bit mmio: [0xe2000000-0xe2ffffff]
[ 1.138469] pci 0000:00:0b.0: bridge 32bit mmio pref: [0xf0000000-0xf80fffff]
[ 1.138483] bus 00 -> node 0
[ 1.138494] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.138658] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[ 1.138746] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP0._PRT]
[ 1.163797] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 18 19) *0
[ 1.164180] ACPI: PCI Interrupt Link [LNK2] (IRQs 16 18 19) *0
[ 1.164549] ACPI: PCI Interrupt Link [LNK3] (IRQs 17) *0
[ 1.164914] ACPI: PCI Interrupt Link [LNK4] (IRQs 16 18 19) *0, disabled.
[ 1.165281] ACPI: PCI Interrupt Link [LNK5] (IRQs 16 18 19) *0
[ 1.165640] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22) *0
[ 1.166000] ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *0
[ 1.166359] ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0
[ 1.166718] ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *0
[ 1.167077] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22) *0, disabled.
[ 1.167437] ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22) *0
[ 1.167802] ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22) *0
[ 1.168181] ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22) *0, disabled.
[ 1.168555] ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *0, disabled.
[ 1.168820] ACPI: WMI: Mapper loaded
[ 1.169202] SCSI subsystem initialized
[ 1.169280] libata version 3.00 loaded.
[ 1.169377] usbcore: registered new interface driver usbfs
[ 1.169412] usbcore: registered new interface driver hub
[ 1.169463] usbcore: registered new device driver usb
[ 1.169679] PCI: Using ACPI for IRQ routing
[ 1.169851] Bluetooth: Core ver 2.13
[ 1.169851] NET: Registered protocol family 31
[ 1.169851] Bluetooth: HCI device and connection manager initialized
[ 1.169851] Bluetooth: HCI socket layer initialized
[ 1.169851] NET: Registered protocol family 8
[ 1.169851] NET: Registered protocol family 20
[ 1.169851] NetLabel: Initializing
[ 1.169851] NetLabel: domain hash size = 128
[ 1.169851] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.169851] NetLabel: unlabeled traffic allowed by default
[ 1.169851] AppArmor: AppArmor Filesystem Enabled
[ 1.169851] pnp: PnP ACPI init
[ 1.169851] ACPI: bus type pnp registered
[ 1.199929] pnp: PnP ACPI: found 12 devices
[ 1.199934] ACPI: ACPI bus type pnp unregistered
[ 1.199940] PnPBIOS: Disabled by ACPI PNP
[ 1.199961] system 00:01: ioport range 0x8000-0x807f has been reserved
[ 1.199968] system 00:01: ioport range 0x8080-0x80ff has been reserved
[ 1.199975] system 00:01: ioport range 0x8400-0x847f has been reserved
[ 1.199981] system 00:01: ioport range 0x8480-0x84ff has been reserved
[ 1.199988] system 00:01: ioport range 0x8800-0x887f has been reserved
[ 1.199994] system 00:01: ioport range 0x8880-0x88ff has been reserved
[ 1.200009] system 00:01: ioport range 0x2040-0x207f has been reserved
[ 1.200015] system 00:01: ioport range 0x2000-0x203f has been reserved
[ 1.200030] system 00:02: iomem range 0xfff80000-0xffffffff has been reserved
[ 1.200037] system 00:02: iomem range 0xfec00000-0xfec00fff has been reserved
[ 1.200044] system 00:02: iomem range 0xfee00000-0xfeefffff has been reserved
[ 1.200051] system 00:02: iomem range 0xfed00000-0xfed00fff has been reserved
[ 1.200065] system 00:03: ioport range 0x200-0x20f has been reserved
[ 1.200071] system 00:03: ioport range 0x680-0x6ff has been reserved
[ 1.200078] system 00:03: ioport range 0x4d0-0x4d1 has been reserved
[ 1.200084] system 00:03: ioport range 0xfe00-0xfe01 has been reserved
[ 1.235040] pci 0000:02:04.0: BAR 10: can't allocate mem resource [0xe4000000-0xe17fffff]
[ 1.235049] pci 0000:02:04.1: BAR 10: can't allocate mem resource [0xe4000000-0xe17fffff]
[ 1.235058] pci 0000:02:04.0: CardBus bridge, secondary bus 0000:03
[ 1.235064] pci 0000:02:04.0: IO window: 0x003000-0x0030ff
[ 1.235072] pci 0000:02:04.0: IO window: 0x003400-0x0034ff
[ 1.235080] pci 0000:02:04.0: PREFETCH window: 0x30000000-0x33ffffff
[ 1.235088] pci 0000:02:04.1: CardBus bridge, secondary bus 0000:07
[ 1.235093] pci 0000:02:04.1: IO window: 0x003800-0x0038ff
[ 1.235100] pci 0000:02:04.1: IO window: 0x003c00-0x003cff
[ 1.235107] pci 0000:02:04.1: PREFETCH window: 0x34000000-0x37ffffff
[ 1.235115] pci 0000:00:0a.0: PCI bridge, secondary bus 0000:02
[ 1.235121] pci 0000:00:0a.0: IO window: 0x3000-0x7fff
[ 1.235128] pci 0000:00:0a.0: MEM window: 0xe0100000-0xe17fffff
[ 1.235135] pci 0000:00:0a.0: PREFETCH window: 0x00000030000000-0x00000037ffffff
[ 1.235146] pci 0000:00:0b.0: PCI bridge, secondary bus 0000:01
[ 1.235150] pci 0000:00:0b.0: IO window: disabled
[ 1.235159] pci 0000:00:0b.0: MEM window: 0xe2000000-0xe2ffffff
[ 1.235166] pci 0000:00:0b.0: PREFETCH window: 0x000000f0000000-0x000000f80fffff
[ 1.235184] pci 0000:00:0a.0: setting latency timer to 64
[ 1.235714] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 19
[ 1.235728] pci 0000:02:04.0: PCI INT A -> Link[LNK1] -> GSI 19 (level, low) -> IRQ 19
[ 1.236244] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 18
[ 1.236255] pci 0000:02:04.1: PCI INT B -> Link[LNK2] -> GSI 18 (level, low) -> IRQ 18
[ 1.236271] bus: 00 index 0 io port: [0x00-0xffff]
[ 1.236277] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 1.236282] bus: 02 index 0 io port: [0x3000-0x7fff]
[ 1.236287] bus: 02 index 1 mmio: [0xe0100000-0xe17fffff]
[ 1.236293] bus: 02 index 2 mmio: [0x30000000-0x37ffffff]
[ 1.236297] bus: 02 index 3 mmio: [0x0-0x0]
[ 1.236303] bus: 03 index 0 io port: [0x3000-0x30ff]
[ 1.236307] bus: 03 index 1 io port: [0x3400-0x34ff]
[ 1.236313] bus: 03 index 2 mmio: [0x30000000-0x33ffffff]
[ 1.236317] bus: 03 index 3 mmio: [0x0-0x0]
[ 1.236322] bus: 07 index 0 io port: [0x3800-0x38ff]
[ 1.236327] bus: 07 index 1 io port: [0x3c00-0x3cff]
[ 1.236332] bus: 07 index 2 mmio: [0x34000000-0x37ffffff]
[ 1.236337] bus: 07 index 3 mmio: [0x0-0x0]
[ 1.236342] bus: 01 index 0 mmio: [0x0-0x0]
[ 1.236346] bus: 01 index 1 mmio: [0xe2000000-0xe2ffffff]
[ 1.236352] bus: 01 index 2 mmio: [0xf0000000-0xf80fffff]
[ 1.236356] bus: 01 index 3 mmio: [0x0-0x0]
[ 1.236379] NET: Registered protocol family 2
[ 1.236613] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.237113] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.237246] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.237380] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.237385] TCP reno registered
[ 1.237548] NET: Registered protocol family 1
[ 1.237811] checking if image is initramfs...Switched to high resolution mode on CPU 0
[ 1.928954] it is
[ 2.677489] Freeing initrd memory: 7365k freed
[ 2.677545] Simple Boot Flag at 0x37 set to 0x1
[ 2.677700] cpufreq: No nForce2 chipset.
[ 2.677944] audit: initializing netlink socket (disabled)
[ 2.677968] type=2000 audit(1248025068.676:1): initialized
[ 2.697223] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 2.700073] VFS: Disk quotas dquot_6.5.1
[ 2.700201] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.701526] fuse init (API version 7.10)
[ 2.701699] msgmni has been set to 993
[ 2.702062] alg: No test for stdrng (krng)
[ 2.702085] io scheduler noop registered
[ 2.702089] io scheduler anticipatory registered
[ 2.702094] io scheduler deadline registered
[ 2.702127] io scheduler cfq registered (default)
[ 3.110449] pci 0000:01:00.0: Boot video device
[ 3.165156] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 3.165177] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 3.170053] ACPI: AC Adapter [ACAD] (on-line)
[ 3.396181] ACPI: Battery Slot [BAT1] (battery present)
[ 3.396331] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 3.396338] ACPI: Power Button (FF) [PWRF]
[ 3.396439] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 3.396446] ACPI: Power Button (CM) [PWRB]
[ 3.396548] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 3.399308] ACPI: Lid Switch [LID]
[ 3.399692] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 3.399745] processor ACPI_CPU:00: registered as cooling_device0
[ 3.439471] thermal LNXTHERM:01: registered as thermal_zone0
[ 3.457535] ACPI: Thermal Zone [THRM] (36 C)
[ 3.457627] isapnp: Scanning for PnP cards...
[ 3.811388] isapnp: No Plug & Play device found
[ 3.814065] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 3.815177] ACPI: PCI Interrupt Link [LMCI] enabled at IRQ 22
[ 3.815195] serial 0000:00:06.1: PCI INT B -> Link[LMCI] -> GSI 22 (level, low) -> IRQ 22
[ 3.815206] serial 0000:00:06.1: PCI INT B disabled
[ 3.816804] brd: module loaded
[ 3.817501] loop: module loaded
[ 3.817658] Fixed MDIO Bus: probed
[ 3.817670] PPP generic driver version 2.4.2
[ 3.817803] input: Macintosh mouse button emulation as /devices/virtual/input/input3
[ 3.817865] Driver 'sd' needs updating - please use bus_type methods
[ 3.817883] Driver 'sr' needs updating - please use bus_type methods
[ 3.818366] pata_amd 0000:00:08.0: version 0.3.10
[ 3.818445] pata_amd 0000:00:08.0: setting latency timer to 64
[ 3.818610] scsi0 : pata_amd
[ 3.818775] scsi1 : pata_amd
[ 3.820241] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2080 irq 14
[ 3.820248] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2088 irq 15
[ 3.984530] ata1.00: ATA-6: FUJITSU MHT2060AT PL, 0022, max UDMA/100
[ 3.984537] ata1.00: 117210240 sectors, multi 16: LBA
[ 3.984600] ata1: nv_mode_filter: 0x3f39f&0x3f01f->0x3f01f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 4.000508] ata1.00: configured for UDMA/100
[ 4.180309] ata2.00: ATAPI: _NEC DVD+/-RW ND-6450A, 2.36, max MWDMA2
[ 4.180368] ata2: nv_mode_filter: 0x39f&0x39f->0x39f, BIOS=0x0 (0xc6000000) ACPI=0x39f (120:600:0x12)
[ 4.228290] ata2.00: configured for MWDMA2
[ 4.245826] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHT2060A 0022 PQ: 0 ANSI: 5
[ 4.246020] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors: (60.0 GB/55.8 GiB)
[ 4.246054] sd 0:0:0:0: [sda] Write Protect is off
[ 4.246061] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.246111] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.246237] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors: (60.0 GB/55.8 GiB)
[ 4.246267] sd 0:0:0:0: [sda] Write Protect is off
[ 4.246273] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.246321] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.246331] sda: sda1 sda2
[ 4.357027] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.357129] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.376743] scsi 1:0:0:0: CD-ROM _NEC DVD+-RW ND-6450A 2.36 PQ: 0 ANSI: 5
[ 4.498998] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 4.499005] Uniform CD-ROM driver Revision: 3.20
[ 4.499201] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 4.499280] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 4.500295] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.500900] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
[ 4.500917] ehci_hcd 0000:00:02.2: PCI INT C -> Link[LUS2] -> GSI 21 (level, low) -> IRQ 21
[ 4.500959] ehci_hcd 0000:00:02.2: setting latency timer to 64
[ 4.500966] ehci_hcd 0000:00:02.2: EHCI Host Controller
[ 4.501092] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
[ 4.501141] ehci_hcd 0000:00:02.2: cache line size of 64 is not supported
[ 4.501171] ehci_hcd 0000:00:02.2: irq 21, io mem 0xe0004000
[ 4.512023] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00
[ 4.512152] usb usb1: configuration #1 chosen from 1 choice
[ 4.512207] hub 1-0:1.0: USB hub found
[ 4.512223] hub 1-0:1.0: 6 ports detected
[ 4.512427] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.512975] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 20
[ 4.512990] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 20 (level, low) -> IRQ 20
[ 4.513015] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 4.513022] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 4.513115] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 4.513152] ohci_hcd 0000:00:02.0: irq 20, io mem 0xe0000000
[ 4.570124] usb usb2: configuration #1 chosen from 1 choice
[ 4.570178] hub 2-0:1.0: USB hub found
[ 4.570195] hub 2-0:1.0: 3 ports detected
[ 4.570848] ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 22
[ 4.570856] ohci_hcd 0000:00:02.1: PCI INT B -> Link[LUS1] -> GSI 22 (level, low) -> IRQ 22
[ 4.570879] ohci_hcd 0000:00:02.1: setting latency timer to 64
[ 4.570885] ohci_hcd 0000:00:02.1: OHCI Host Controller
[ 4.570972] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
[ 4.571009] ohci_hcd 0000:00:02.1: irq 22, io mem 0xe0001000
[ 4.626108] usb usb3: configuration #1 chosen from 1 choice
[ 4.626163] hub 3-0:1.0: USB hub found
[ 4.626178] hub 3-0:1.0: 3 ports detected
[ 4.626346] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.626510] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 4.634795] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 4.642266] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.642276] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 4.642283] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 4.642288] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 4.642294] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 4.642609] mice: PS/2 mouse device common for all mice
[ 4.642920] rtc_cmos 00:06: RTC can wake from S4
[ 4.642998] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 4.643034] rtc0: alarms up to one year, y3k, 114 bytes nvram
[ 4.643162] device-mapper: uevent: version 1.0.3
[ 4.643373] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 4.643463] device-mapper: multipath: version 1.0.5 loaded
[ 4.643469] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 4.643630] EISA: Probing bus 0 at eisa.0
[ 4.643643] Cannot allocate resource for EISA slot 1
[ 4.643648] Cannot allocate resource for EISA slot 2
[ 4.643653] Cannot allocate resource for EISA slot 3
[ 4.643658] Cannot allocate resource for EISA slot 4
[ 4.643663] Cannot allocate resource for EISA slot 5
[ 4.643668] Cannot allocate resource for EISA slot 6
[ 4.643672] Cannot allocate resource for EISA slot 7
[ 4.643677] Cannot allocate resource for EISA slot 8
[ 4.643682] EISA: Detected 0 cards.
[ 4.643787] cpuidle: using governor ladder
[ 4.643882] cpuidle: using governor menu
[ 4.645004] TCP cubic registered
[ 4.645224] NET: Registered protocol family 10
[ 4.646108] lo: Disabled Privacy Extensions
[ 4.646808] NET: Registered protocol family 17
[ 4.646843] Bluetooth: L2CAP ver 2.11
[ 4.646847] Bluetooth: L2CAP socket layer initialized
[ 4.646853] Bluetooth: SCO (Voice Link) ver 0.6
[ 4.646857] Bluetooth: SCO socket layer initialized
[ 4.646916] Bluetooth: RFCOMM socket layer initialized
[ 4.646930] Bluetooth: RFCOMM TTY layer initialized
[ 4.646934] Bluetooth: RFCOMM ver 1.10
[ 4.646978] powernow-k8: Found 1 AMD Athlon(tm) XP Processor 3000+ processors (1 cpu cores) (version 2.20.00)
[ 4.647046] powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x6
[ 4.647051] powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x18
[ 4.647107] Marking TSC unstable due to cpufreq changes
[ 4.651216] Using IPI No-Shortcut mode
[ 4.651323] registered taskstats version 1
[ 4.651470] Magic number: 1:817:643
[ 4.651564] rtc_cmos 00:06: setting system clock to 2009-07-19 17:37:51 UTC (1248025071)
[ 4.651567] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 4.651569] EDD information not available.
[ 4.652124] Freeing unused kernel memory: 532k freed
[ 4.652280] Write protecting the kernel text: 4112k
[ 4.652332] Write protecting the kernel read-only data: 1524k
[ 4.690055] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 4.732032] Clocksource tsc unstable (delta = 80994378 ns)
[ 5.397971] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 5.398005] 8139cp 0000:02:01.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 5.401202] 8139too Fast Ethernet driver 0.9.28
[ 5.401254] 8139too 0000:02:01.0: PCI INT A -> Link[LNK2] -> GSI 18 (level, low) -> IRQ 18
[ 5.402247] eth0: RealTek RTL8139 at 0x7000, 00:0f:b0:3e:5a:69, IRQ 18
[ 5.402250] eth0: Identified 8139 chip type 'RTL-8101'
[ 5.415175] ohci1394 0000:02:00.0: PCI INT A -> Link[LNK1] -> GSI 19 (level, low) -> IRQ 19
[ 5.464991] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[e0108000-e01087ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 5.476885] ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 17
[ 5.476901] b43-pci-bridge 0000:02:02.0: PCI INT A -> Link[LNK3] -> GSI 17 (level, low) -> IRQ 17
[ 5.480366] ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0
[ 5.921691] b44.c:v2.0
[ 5.921708] b44: Invalid MAC address found in EEPROM
[ 5.921713] b44 ssb0:1: Problem fetching invariants of chip, aborting.
[ 5.921721] b44: probe of ssb0:1 failed with error -22
[ 6.748164] ieee1394: Host added: ID:BUS[0-00:1023] GUID[4a3f02004a3f0200]
[ 8.312048] floppy0: no floppy controllers found
[ 8.408710] kjournald starting. Commit interval 5 seconds
[ 8.408726] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.900082] udev: starting version 141
[ 16.453668] parport_pc 00:0b: reported by Plug and Play ACPI
[ 16.453720] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 16.458786] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:18/device:19/input/input5
[ 16.488188] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 16.739026] Linux agpgart interface v0.103
[ 16.771488] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 16.809631] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 16.902046] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 16.931646] ppdev: user-space parallel port driver
[ 17.206170] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x2040
[ 17.206258] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2000
[ 17.551038] input: PS/2 Mouse as /devices/platform/i8042/serio4/input/input7
[ 17.588570] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio4/input/input8
[ 17.643783] nvidia: module license 'NVIDIA' taints kernel.
[ 17.902375] agpgart-amd64 0000:00:00.0: AGP bridge [10de/00d1]
[ 17.902416] agpgart-amd64 0000:00:00.0: setting up Nforce3 AGP
[ 17.909033] agpgart-amd64 0000:00:00.0: AGP aperture is 128M @ 0xe8000000
[ 17.919406] nvidia 0000:01:00.0: power state changed by ACPI to D0
[ 17.919777] ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 16
[ 17.919790] nvidia 0000:01:00.0: PCI INT A -> Link[LNK5] -> GSI 16 (level, low) -> IRQ 16
[ 17.921411] NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.10 Sat Jan 24 19:49:38 PST 2009
[ 18.023100] yenta_cardbus 0000:02:04.0: CardBus bridge found [103c:006d]
[ 18.023119] yenta_cardbus 0000:02:04.0: CardBus bridge, secondary bus 0000:03
[ 18.023123] yenta_cardbus 0000:02:04.0: IO window: 0x003000-0x0030ff
[ 18.023127] yenta_cardbus 0000:02:04.0: IO window: 0x003400-0x0034ff
[ 18.023132] yenta_cardbus 0000:02:04.0: PREFETCH window: 0x30000000-0x33ffffff
[ 18.023137] yenta_cardbus 0000:02:04.0: MEM window: 0xe0400000-0xe07fffff
[ 18.023143] yenta_cardbus 0000:02:04.0: Enabling burst memory read transactions
[ 18.023148] yenta_cardbus 0000:02:04.0: Using CSCINT to route CSC interrupts to PCI
[ 18.023151] yenta_cardbus 0000:02:04.0: Routing CardBus interrupts to PCI
[ 18.023156] yenta_cardbus 0000:02:04.0: TI: mfunc 0x01111d22, devctl 0x64
[ 18.044129] cfg80211: Calling CRDA to update world regulatory domain
[ 18.183873] cfg80211: World regulatory domain updated:
[ 18.183880] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 18.183884] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.183888] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 18.183891] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 18.183893] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.183896] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.252862] yenta_cardbus 0000:02:04.0: ISA IRQ mask 0x0c38, PCI irq 19
[ 18.252868] yenta_cardbus 0000:02:04.0: Socket status: 30000086
[ 18.252873] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #02 to #06
[ 18.252882] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff
[ 18.252887] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3000-0x7fff: clean.
[ 18.253879] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge Memory window: 0xe0100000 - 0xe17fffff
[ 18.253883] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x37ffffff
[ 18.254462] yenta_cardbus 0000:02:04.1: CardBus bridge found [103c:006d]
[ 18.254480] yenta_cardbus 0000:02:04.1: Using CSCINT to route CSC interrupts to PCI
[ 18.254483] yenta_cardbus 0000:02:04.1: Routing CardBus interrupts to PCI
[ 18.254488] yenta_cardbus 0000:02:04.1: TI: mfunc 0x01111d22, devctl 0x64
[ 18.291099] b43legacy-phy0: Broadcom 4301 WLAN found
[ 18.316072] b43legacy-phy0 debug: Found PHY: Analog 0, Type 1, Revision 4
[ 18.316096] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[ 18.340049] b43legacy-phy0 debug: Radio initialized
[ 18.342138] phy0: Selected rate control algorithm 'pid'
[ 18.424274] ACPI: PCI Interrupt Link [LACI] enabled at IRQ 21
[ 18.424282] Intel ICH 0000:00:06.0: PCI INT A -> Link[LACI] -> GSI 21 (level, low) -> IRQ 21
[ 18.424364] Intel ICH 0000:00:06.0: setting latency timer to 64
[ 18.452926] Broadcom 43xx-legacy driver loaded [ Features: PLRID, Firmware-ID: FW10 ]
[ 18.484852] yenta_cardbus 0000:02:04.1: ISA IRQ mask 0x0c38, PCI irq 18
[ 18.484858] yenta_cardbus 0000:02:04.1: Socket status: 30000006
[ 18.484863] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #06 to #0a
[ 18.484872] yenta_cardbus 0000:02:04.1: pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff
[ 18.484877] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3000-0x7fff: clean.
[ 18.485869] yenta_cardbus 0000:02:04.1: pcmcia: parent PCI bridge Memory window: 0xe0100000 - 0xe17fffff
[ 18.485873] yenta_cardbus 0000:02:04.1: pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x37ffffff
[ 18.536032] AC'97 0 analog subsections not ready
[ 19.104042] intel8x0_measure_ac97_clock: measured 55410 usecs
[ 19.104047] intel8x0: clocking to 47494
[ 19.107036] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 19.108876] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[ 19.109648] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 19.110290] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 19.111116] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 19.112572] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af: clean.
[ 19.114315] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff: clean.
[ 19.115083] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff: clean.
[ 19.115727] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7: clean.
[ 19.116614] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
[ 19.164048] floppy0: no floppy controllers found
[ 19.318324] lp0: using parport0 (interrupt-driven).
[ 19.970139] EXT3 FS on sda1, internal journal
[ 21.299347] type=1505 audit(1248025088.144:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2011
[ 21.368633] type=1505 audit(1248025088.216:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2015
[ 21.368848] type=1505 audit(1248025088.216:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2015
[ 21.368915] type=1505 audit(1248025088.216:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2015
[ 21.368974] type=1505 audit(1248025088.216:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2015
[ 21.576167] type=1505 audit(1248025088.424:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2020
[ 21.576429] type=1505 audit(1248025088.424:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2020
[ 21.618517] type=1505 audit(1248025088.464:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2024
[ 28.332423] input: b43legacy-phy0 as /devices/virtual/input/input9
[ 28.364075] b43legacy ssb0:0: firmware: requesting b43legacy/ucode2.fw
[ 28.492736] b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw
[ 28.514372] b43legacy ssb0:0: firmware: requesting b43legacy/b0g0initvals2.fw
[ 28.620047] b43legacy-phy0: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
[ 28.720309] b43legacy-phy0 debug: Chip initialized
[ 28.720526] b43legacy-phy0 debug: 30-bit DMA initialized
[ 28.722014] Registered led device: b43legacy-phy0:tx
[ 28.722035] Registered led device: b43legacy-phy0:rx
[ 28.722057] Registered led device: b43legacy-phy0:radio
[ 28.722099] b43legacy-phy0 debug: Wireless interface started
[ 28.728085] b43legacy-phy0 debug: Adding Interface type 2
[ 28.740106] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 29.194992] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 29.194996] Bluetooth: BNEP filters: protocol multicast
[ 29.221552] Bridge firewalling registered
[ 29.337029] b43legacy-phy0: Radio hardware status changed to DISABLED
[ 29.337688] b43legacy-phy0 debug: Radio initialized
[ 29.424022] b43legacy-phy0: Radio turned on by software
[ 29.424028] b43legacy-phy0: The hardware RF-kill button still turns the radio physically off. Press the button to turn it on.
[ 30.403348] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 32.094237] agpgart-amd64 0000:00:00.0: AGP 2.0 bridge
[ 32.094257] agpgart-amd64 0000:00:00.0: putting AGP V2 device into 4x mode
[ 32.094312] nvidia 0000:01:00.0: putting AGP V2 device into 4x mode
[ 34.545203] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 45.476034] eth0: no IPv6 routers present
[ 1.137644] pci 0000:00:08.0: reg 20 io port: [0x2080-0x208f]
[ 1.137855] pci 0000:02:00.0: reg 10 32bit mmio: [0xe0108000-0xe01087ff]
[ 1.137865] pci 0000:02:00.0: reg 14 32bit mmio: [0xe0100000-0xe0103fff]
[ 1.137898] pci 0000:02:00.0: supports D1 D2
[ 1.137903] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot
[ 1.137910] pci 0000:02:00.0: PME# disabled
[ 1.137942] pci 0000:02:01.0: reg 10 io port: [0x7000-0x70ff]
[ 1.137952] pci 0000:02:01.0: reg 14 32bit mmio: [0xe0108800-0xe01088ff]
[ 1.137984] pci 0000:02:01.0: supports D1 D2
[ 1.137989] pci 0000:02:01.0: PME# supported from D1 D2 D3hot D3cold
[ 1.137995] pci 0000:02:01.0: PME# disabled
[ 1.138018] pci 0000:02:02.0: reg 10 32bit mmio: [0xe0104000-0xe0105fff]
[ 1.138077] pci 0000:02:04.0: reg 10 32bit mmio: [0xe0106000-0xe0106fff]
[ 1.138090] pci 0000:02:04.0: supports D1 D2
[ 1.138094] pci 0000:02:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.138101] pci 0000:02:04.0: PME# disabled
[ 1.138135] pci 0000:02:04.1: reg 10 32bit mmio: [0xe0107000-0xe0107fff]
[ 1.138148] pci 0000:02:04.1: supports D1 D2
[ 1.138152] pci 0000:02:04.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.138159] pci 0000:02:04.1: PME# disabled
[ 1.138190] pci 0000:02:04.2: reg 10 io port: [0x7400-0x743f]
[ 1.138266] pci 0000:00:0a.0: bridge io port: [0x3000-0x7fff]
[ 1.138273] pci 0000:00:0a.0: bridge 32bit mmio: [0xe0100000-0xe17fffff]
[ 1.138353] pci 0000:01:00.0: reg 10 32bit mmio: [0xe2000000-0xe2ffffff]
[ 1.138364] pci 0000:01:00.0: reg 14 32bit mmio: [0xf0000000-0xf7ffffff]
[ 1.138374] pci 0000:01:00.0: reg 18 32bit mmio: [0xf8000000-0xf807ffff]
[ 1.138399] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[ 1.138461] pci 0000:00:0b.0: bridge 32bit mmio: [0xe2000000-0xe2ffffff]
[ 1.138469] pci 0000:00:0b.0: bridge 32bit mmio pref: [0xf0000000-0xf80fffff]
[ 1.138483] bus 00 -> node 0
[ 1.138494] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.138658] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
[ 1.138746] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP0._PRT]
[ 1.163797] ACPI: PCI Interrupt Link [LNK1] (IRQs 16 18 19) *0
[ 1.164180] ACPI: PCI Interrupt Link [LNK2] (IRQs 16 18 19) *0
[ 1.164549] ACPI: PCI Interrupt Link [LNK3] (IRQs 17) *0
[ 1.164914] ACPI: PCI Interrupt Link [LNK4] (IRQs 16 18 19) *0, disabled.
[ 1.165281] ACPI: PCI Interrupt Link [LNK5] (IRQs 16 18 19) *0
[ 1.165640] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22) *0
[ 1.166000] ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *0
[ 1.166359] ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0
[ 1.166718] ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *0
[ 1.167077] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22) *0, disabled.
[ 1.167437] ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22) *0
[ 1.167802] ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22) *0
[ 1.168181] ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22) *0, disabled.
[ 1.168555] ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *0, disabled.
[ 1.168820] ACPI: WMI: Mapper loaded
[ 1.169202] SCSI subsystem initialized
[ 1.169280] libata version 3.00 loaded.
[ 1.169377] usbcore: registered new interface driver usbfs
[ 1.169412] usbcore: registered new interface driver hub
[ 1.169463] usbcore: registered new device driver usb
[ 1.169679] PCI: Using ACPI for IRQ routing
[ 1.169851] Bluetooth: Core ver 2.13
[ 1.169851] NET: Registered protocol family 31
[ 1.169851] Bluetooth: HCI device and connection manager initialized
[ 1.169851] Bluetooth: HCI socket layer initialized
[ 1.169851] NET: Registered protocol family 8
[ 1.169851] NET: Registered protocol family 20
[ 1.169851] NetLabel: Initializing
[ 1.169851] NetLabel: domain hash size = 128
[ 1.169851] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.169851] NetLabel: unlabeled traffic allowed by default
[ 1.169851] AppArmor: AppArmor Filesystem Enabled
[ 1.169851] pnp: PnP ACPI init
[ 1.169851] ACPI: bus type pnp registered
[ 1.199929] pnp: PnP ACPI: found 12 devices
[ 1.199934] ACPI: ACPI bus type pnp unregistered
[ 1.199940] PnPBIOS: Disabled by ACPI PNP
[ 1.199961] system 00:01: ioport range 0x8000-0x807f has been reserved
[ 1.199968] system 00:01: ioport range 0x8080-0x80ff has been reserved
[ 1.199975] system 00:01: ioport range 0x8400-0x847f has been reserved
[ 1.199981] system 00:01: ioport range 0x8480-0x84ff has been reserved
[ 1.199988] system 00:01: ioport range 0x8800-0x887f has been reserved
[ 1.199994] system 00:01: ioport range 0x8880-0x88ff has been reserved
[ 1.200009] system 00:01: ioport range 0x2040-0x207f has been reserved
[ 1.200015] system 00:01: ioport range 0x2000-0x203f has been reserved
[ 1.200030] system 00:02: iomem range 0xfff80000-0xffffffff has been reserved
[ 1.200037] system 00:02: iomem range 0xfec00000-0xfec00fff has been reserved
[ 1.200044] system 00:02: iomem range 0xfee00000-0xfeefffff has been reserved
[ 1.200051] system 00:02: iomem range 0xfed00000-0xfed00fff has been reserved
[ 1.200065] system 00:03: ioport range 0x200-0x20f has been reserved
[ 1.200071] system 00:03: ioport range 0x680-0x6ff has been reserved
[ 1.200078] system 00:03: ioport range 0x4d0-0x4d1 has been reserved
[ 1.200084] system 00:03: ioport range 0xfe00-0xfe01 has been reserved
[ 1.235040] pci 0000:02:04.0: BAR 10: can't allocate mem resource [0xe4000000-0xe17fffff]
[ 1.235049] pci 0000:02:04.1: BAR 10: can't allocate mem resource [0xe4000000-0xe17fffff]
[ 1.235058] pci 0000:02:04.0: CardBus bridge, secondary bus 0000:03
[ 1.235064] pci 0000:02:04.0: IO window: 0x003000-0x0030ff
[ 1.235072] pci 0000:02:04.0: IO window: 0x003400-0x0034ff
[ 1.235080] pci 0000:02:04.0: PREFETCH window: 0x30000000-0x33ffffff
[ 1.235088] pci 0000:02:04.1: CardBus bridge, secondary bus 0000:07
[ 1.235093] pci 0000:02:04.1: IO window: 0x003800-0x0038ff
[ 1.235100] pci 0000:02:04.1: IO window: 0x003c00-0x003cff
[ 1.235107] pci 0000:02:04.1: PREFETCH window: 0x34000000-0x37ffffff
[ 1.235115] pci 0000:00:0a.0: PCI bridge, secondary bus 0000:02
[ 1.235121] pci 0000:00:0a.0: IO window: 0x3000-0x7fff
[ 1.235128] pci 0000:00:0a.0: MEM window: 0xe0100000-0xe17fffff
[ 1.235135] pci 0000:00:0a.0: PREFETCH window: 0x00000030000000-0x00000037ffffff
[ 1.235146] pci 0000:00:0b.0: PCI bridge, secondary bus 0000:01
[ 1.235150] pci 0000:00:0b.0: IO window: disabled
[ 1.235159] pci 0000:00:0b.0: MEM window: 0xe2000000-0xe2ffffff
[ 1.235166] pci 0000:00:0b.0: PREFETCH window: 0x000000f0000000-0x000000f80fffff
[ 1.235184] pci 0000:00:0a.0: setting latency timer to 64
[ 1.235714] ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 19
[ 1.235728] pci 0000:02:04.0: PCI INT A -> Link[LNK1] -> GSI 19 (level, low) -> IRQ 19
[ 1.236244] ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 18
[ 1.236255] pci 0000:02:04.1: PCI INT B -> Link[LNK2] -> GSI 18 (level, low) -> IRQ 18
[ 1.236271] bus: 00 index 0 io port: [0x00-0xffff]
[ 1.236277] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 1.236282] bus: 02 index 0 io port: [0x3000-0x7fff]
[ 1.236287] bus: 02 index 1 mmio: [0xe0100000-0xe17fffff]
[ 1.236293] bus: 02 index 2 mmio: [0x30000000-0x37ffffff]
[ 1.236297] bus: 02 index 3 mmio: [0x0-0x0]
[ 1.236303] bus: 03 index 0 io port: [0x3000-0x30ff]
[ 1.236307] bus: 03 index 1 io port: [0x3400-0x34ff]
[ 1.236313] bus: 03 index 2 mmio: [0x30000000-0x33ffffff]
[ 1.236317] bus: 03 index 3 mmio: [0x0-0x0]
[ 1.236322] bus: 07 index 0 io port: [0x3800-0x38ff]
[ 1.236327] bus: 07 index 1 io port: [0x3c00-0x3cff]
[ 1.236332] bus: 07 index 2 mmio: [0x34000000-0x37ffffff]
[ 1.236337] bus: 07 index 3 mmio: [0x0-0x0]
[ 1.236342] bus: 01 index 0 mmio: [0x0-0x0]
[ 1.236346] bus: 01 index 1 mmio: [0xe2000000-0xe2ffffff]
[ 1.236352] bus: 01 index 2 mmio: [0xf0000000-0xf80fffff]
[ 1.236356] bus: 01 index 3 mmio: [0x0-0x0]
[ 1.236379] NET: Registered protocol family 2
[ 1.236613] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.237113] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.237246] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.237380] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.237385] TCP reno registered
[ 1.237548] NET: Registered protocol family 1
[ 1.237811] checking if image is initramfs...Switched to high resolution mode on CPU 0
[ 1.928954] it is
[ 2.677489] Freeing initrd memory: 7365k freed
[ 2.677545] Simple Boot Flag at 0x37 set to 0x1
[ 2.677700] cpufreq: No nForce2 chipset.
[ 2.677944] audit: initializing netlink socket (disabled)
[ 2.677968] type=2000 audit(1248025068.676:1): initialized
[ 2.697223] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 2.700073] VFS: Disk quotas dquot_6.5.1
[ 2.700201] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 2.701526] fuse init (API version 7.10)
[ 2.701699] msgmni has been set to 993
[ 2.702062] alg: No test for stdrng (krng)
[ 2.702085] io scheduler noop registered
[ 2.702089] io scheduler anticipatory registered
[ 2.702094] io scheduler deadline registered
[ 2.702127] io scheduler cfq registered (default)
[ 3.110449] pci 0000:01:00.0: Boot video device
[ 3.165156] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 3.165177] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 3.170053] ACPI: AC Adapter [ACAD] (on-line)
[ 3.396181] ACPI: Battery Slot [BAT1] (battery present)
[ 3.396331] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 3.396338] ACPI: Power Button (FF) [PWRF]
[ 3.396439] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 3.396446] ACPI: Power Button (CM) [PWRB]
[ 3.396548] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input2
[ 3.399308] ACPI: Lid Switch [LID]
[ 3.399692] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 3.399745] processor ACPI_CPU:00: registered as cooling_device0
[ 3.439471] thermal LNXTHERM:01: registered as thermal_zone0
[ 3.457535] ACPI: Thermal Zone [THRM] (36 C)
[ 3.457627] isapnp: Scanning for PnP cards...
[ 3.811388] isapnp: No Plug & Play device found
[ 3.814065] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 3.815177] ACPI: PCI Interrupt Link [LMCI] enabled at IRQ 22
[ 3.815195] serial 0000:00:06.1: PCI INT B -> Link[LMCI] -> GSI 22 (level, low) -> IRQ 22
[ 3.815206] serial 0000:00:06.1: PCI INT B disabled
[ 3.816804] brd: module loaded
[ 3.817501] loop: module loaded
[ 3.817658] Fixed MDIO Bus: probed
[ 3.817670] PPP generic driver version 2.4.2
[ 3.817803] input: Macintosh mouse button emulation as /devices/virtual/input/input3
[ 3.817865] Driver 'sd' needs updating - please use bus_type methods
[ 3.817883] Driver 'sr' needs updating - please use bus_type methods
[ 3.818366] pata_amd 0000:00:08.0: version 0.3.10
[ 3.818445] pata_amd 0000:00:08.0: setting latency timer to 64
[ 3.818610] scsi0 : pata_amd
[ 3.818775] scsi1 : pata_amd
[ 3.820241] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2080 irq 14
[ 3.820248] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2088 irq 15
[ 3.984530] ata1.00: ATA-6: FUJITSU MHT2060AT PL, 0022, max UDMA/100
[ 3.984537] ata1.00: 117210240 sectors, multi 16: LBA
[ 3.984600] ata1: nv_mode_filter: 0x3f39f&0x3f01f->0x3f01f, BIOS=0x3f000 (0xc6000000) ACPI=0x3f01f (20:600:0x13)
[ 4.000508] ata1.00: configured for UDMA/100
[ 4.180309] ata2.00: ATAPI: _NEC DVD+/-RW ND-6450A, 2.36, max MWDMA2
[ 4.180368] ata2: nv_mode_filter: 0x39f&0x39f->0x39f, BIOS=0x0 (0xc6000000) ACPI=0x39f (120:600:0x12)
[ 4.228290] ata2.00: configured for MWDMA2
[ 4.245826] scsi 0:0:0:0: Direct-Access ATA FUJITSU MHT2060A 0022 PQ: 0 ANSI: 5
[ 4.246020] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors: (60.0 GB/55.8 GiB)
[ 4.246054] sd 0:0:0:0: [sda] Write Protect is off
[ 4.246061] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.246111] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.246237] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors: (60.0 GB/55.8 GiB)
[ 4.246267] sd 0:0:0:0: [sda] Write Protect is off
[ 4.246273] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.246321] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.246331] sda: sda1 sda2
[ 4.357027] sd 0:0:0:0: [sda] Attached SCSI disk
[ 4.357129] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 4.376743] scsi 1:0:0:0: CD-ROM _NEC DVD+-RW ND-6450A 2.36 PQ: 0 ANSI: 5
[ 4.498998] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 4.499005] Uniform CD-ROM driver Revision: 3.20
[ 4.499201] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 4.499280] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 4.500295] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.500900] ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 21
[ 4.500917] ehci_hcd 0000:00:02.2: PCI INT C -> Link[LUS2] -> GSI 21 (level, low) -> IRQ 21
[ 4.500959] ehci_hcd 0000:00:02.2: setting latency timer to 64
[ 4.500966] ehci_hcd 0000:00:02.2: EHCI Host Controller
[ 4.501092] ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
[ 4.501141] ehci_hcd 0000:00:02.2: cache line size of 64 is not supported
[ 4.501171] ehci_hcd 0000:00:02.2: irq 21, io mem 0xe0004000
[ 4.512023] ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00
[ 4.512152] usb usb1: configuration #1 chosen from 1 choice
[ 4.512207] hub 1-0:1.0: USB hub found
[ 4.512223] hub 1-0:1.0: 6 ports detected
[ 4.512427] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.512975] ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 20
[ 4.512990] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 20 (level, low) -> IRQ 20
[ 4.513015] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 4.513022] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 4.513115] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 4.513152] ohci_hcd 0000:00:02.0: irq 20, io mem 0xe0000000
[ 4.570124] usb usb2: configuration #1 chosen from 1 choice
[ 4.570178] hub 2-0:1.0: USB hub found
[ 4.570195] hub 2-0:1.0: 3 ports detected
[ 4.570848] ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 22
[ 4.570856] ohci_hcd 0000:00:02.1: PCI INT B -> Link[LUS1] -> GSI 22 (level, low) -> IRQ 22
[ 4.570879] ohci_hcd 0000:00:02.1: setting latency timer to 64
[ 4.570885] ohci_hcd 0000:00:02.1: OHCI Host Controller
[ 4.570972] ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
[ 4.571009] ohci_hcd 0000:00:02.1: irq 22, io mem 0xe0001000
[ 4.626108] usb usb3: configuration #1 chosen from 1 choice
[ 4.626163] hub 3-0:1.0: USB hub found
[ 4.626178] hub 3-0:1.0: 3 ports detected
[ 4.626346] uhci_hcd: USB Universal Host Controller Interface driver
[ 4.626510] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 4.634795] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 4.642266] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 4.642276] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 4.642283] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 4.642288] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 4.642294] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 4.642609] mice: PS/2 mouse device common for all mice
[ 4.642920] rtc_cmos 00:06: RTC can wake from S4
[ 4.642998] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 4.643034] rtc0: alarms up to one year, y3k, 114 bytes nvram
[ 4.643162] device-mapper: uevent: version 1.0.3
[ 4.643373] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 4.643463] device-mapper: multipath: version 1.0.5 loaded
[ 4.643469] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 4.643630] EISA: Probing bus 0 at eisa.0
[ 4.643643] Cannot allocate resource for EISA slot 1
[ 4.643648] Cannot allocate resource for EISA slot 2
[ 4.643653] Cannot allocate resource for EISA slot 3
[ 4.643658] Cannot allocate resource for EISA slot 4
[ 4.643663] Cannot allocate resource for EISA slot 5
[ 4.643668] Cannot allocate resource for EISA slot 6
[ 4.643672] Cannot allocate resource for EISA slot 7
[ 4.643677] Cannot allocate resource for EISA slot 8
[ 4.643682] EISA: Detected 0 cards.
[ 4.643787] cpuidle: using governor ladder
[ 4.643882] cpuidle: using governor menu
[ 4.645004] TCP cubic registered
[ 4.645224] NET: Registered protocol family 10
[ 4.646108] lo: Disabled Privacy Extensions
[ 4.646808] NET: Registered protocol family 17
[ 4.646843] Bluetooth: L2CAP ver 2.11
[ 4.646847] Bluetooth: L2CAP socket layer initialized
[ 4.646853] Bluetooth: SCO (Voice Link) ver 0.6
[ 4.646857] Bluetooth: SCO socket layer initialized
[ 4.646916] Bluetooth: RFCOMM socket layer initialized
[ 4.646930] Bluetooth: RFCOMM TTY layer initialized
[ 4.646934] Bluetooth: RFCOMM ver 1.10
[ 4.646978] powernow-k8: Found 1 AMD Athlon(tm) XP Processor 3000+ processors (1 cpu cores) (version 2.20.00)
[ 4.647046] powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x6
[ 4.647051] powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x18
[ 4.647107] Marking TSC unstable due to cpufreq changes
[ 4.651216] Using IPI No-Shortcut mode
[ 4.651323] registered taskstats version 1
[ 4.651470] Magic number: 1:817:643
[ 4.651564] rtc_cmos 00:06: setting system clock to 2009-07-19 17:37:51 UTC (1248025071)
[ 4.651567] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 4.651569] EDD information not available.
[ 4.652124] Freeing unused kernel memory: 532k freed
[ 4.652280] Write protecting the kernel text: 4112k
[ 4.652332] Write protecting the kernel read-only data: 1524k
[ 4.690055] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 4.732032] Clocksource tsc unstable (delta = 80994378 ns)
[ 5.397971] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 5.398005] 8139cp 0000:02:01.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too
[ 5.401202] 8139too Fast Ethernet driver 0.9.28
[ 5.401254] 8139too 0000:02:01.0: PCI INT A -> Link[LNK2] -> GSI 18 (level, low) -> IRQ 18
[ 5.402247] eth0: RealTek RTL8139 at 0x7000, 00:0f:b0:3e:5a:69, IRQ 18
[ 5.402250] eth0: Identified 8139 chip type 'RTL-8101'
[ 5.415175] ohci1394 0000:02:00.0: PCI INT A -> Link[LNK1] -> GSI 19 (level, low) -> IRQ 19
[ 5.464991] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[e0108000-e01087ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 5.476885] ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 17
[ 5.476901] b43-pci-bridge 0000:02:02.0: PCI INT A -> Link[LNK3] -> GSI 17 (level, low) -> IRQ 17
[ 5.480366] ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0
[ 5.921691] b44.c:v2.0
[ 5.921708] b44: Invalid MAC address found in EEPROM
[ 5.921713] b44 ssb0:1: Problem fetching invariants of chip, aborting.
[ 5.921721] b44: probe of ssb0:1 failed with error -22
[ 6.748164] ieee1394: Host added: ID:BUS[0-00:1023] GUID[4a3f02004a3f0200]
[ 8.312048] floppy0: no floppy controllers found
[ 8.408710] kjournald starting. Commit interval 5 seconds
[ 8.408726] EXT3-fs: mounted filesystem with ordered data mode.
[ 15.900082] udev: starting version 141
[ 16.453668] parport_pc 00:0b: reported by Plug and Play ACPI
[ 16.453720] parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 16.458786] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:18/device:19/input/input5
[ 16.488188] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 16.739026] Linux agpgart interface v0.103
[ 16.771488] input: PC Speaker as /devices/platform/pcspkr/input/input6
[ 16.809631] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 16.902046] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 16.931646] ppdev: user-space parallel port driver
[ 17.206170] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x2040
[ 17.206258] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2000
[ 17.551038] input: PS/2 Mouse as /devices/platform/i8042/serio4/input/input7
[ 17.588570] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio4/input/input8
[ 17.643783] nvidia: module license 'NVIDIA' taints kernel.
[ 17.902375] agpgart-amd64 0000:00:00.0: AGP bridge [10de/00d1]
[ 17.902416] agpgart-amd64 0000:00:00.0: setting up Nforce3 AGP
[ 17.909033] agpgart-amd64 0000:00:00.0: AGP aperture is 128M @ 0xe8000000
[ 17.919406] nvidia 0000:01:00.0: power state changed by ACPI to D0
[ 17.919777] ACPI: PCI Interrupt Link [LNK5] enabled at IRQ 16
[ 17.919790] nvidia 0000:01:00.0: PCI INT A -> Link[LNK5] -> GSI 16 (level, low) -> IRQ 16
[ 17.921411] NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.10 Sat Jan 24 19:49:38 PST 2009
[ 18.023100] yenta_cardbus 0000:02:04.0: CardBus bridge found [103c:006d]
[ 18.023119] yenta_cardbus 0000:02:04.0: CardBus bridge, secondary bus 0000:03
[ 18.023123] yenta_cardbus 0000:02:04.0: IO window: 0x003000-0x0030ff
[ 18.023127] yenta_cardbus 0000:02:04.0: IO window: 0x003400-0x0034ff
[ 18.023132] yenta_cardbus 0000:02:04.0: PREFETCH window: 0x30000000-0x33ffffff
[ 18.023137] yenta_cardbus 0000:02:04.0: MEM window: 0xe0400000-0xe07fffff
[ 18.023143] yenta_cardbus 0000:02:04.0: Enabling burst memory read transactions
[ 18.023148] yenta_cardbus 0000:02:04.0: Using CSCINT to route CSC interrupts to PCI
[ 18.023151] yenta_cardbus 0000:02:04.0: Routing CardBus interrupts to PCI
[ 18.023156] yenta_cardbus 0000:02:04.0: TI: mfunc 0x01111d22, devctl 0x64
[ 18.044129] cfg80211: Calling CRDA to update world regulatory domain
[ 18.183873] cfg80211: World regulatory domain updated:
[ 18.183880] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 18.183884] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.183888] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 18.183891] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 18.183893] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.183896] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 18.252862] yenta_cardbus 0000:02:04.0: ISA IRQ mask 0x0c38, PCI irq 19
[ 18.252868] yenta_cardbus 0000:02:04.0: Socket status: 30000086
[ 18.252873] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #02 to #06
[ 18.252882] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff
[ 18.252887] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3000-0x7fff: clean.
[ 18.253879] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge Memory window: 0xe0100000 - 0xe17fffff
[ 18.253883] yenta_cardbus 0000:02:04.0: pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x37ffffff
[ 18.254462] yenta_cardbus 0000:02:04.1: CardBus bridge found [103c:006d]
[ 18.254480] yenta_cardbus 0000:02:04.1: Using CSCINT to route CSC interrupts to PCI
[ 18.254483] yenta_cardbus 0000:02:04.1: Routing CardBus interrupts to PCI
[ 18.254488] yenta_cardbus 0000:02:04.1: TI: mfunc 0x01111d22, devctl 0x64
[ 18.291099] b43legacy-phy0: Broadcom 4301 WLAN found
[ 18.316072] b43legacy-phy0 debug: Found PHY: Analog 0, Type 1, Revision 4
[ 18.316096] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[ 18.340049] b43legacy-phy0 debug: Radio initialized
[ 18.342138] phy0: Selected rate control algorithm 'pid'
[ 18.424274] ACPI: PCI Interrupt Link [LACI] enabled at IRQ 21
[ 18.424282] Intel ICH 0000:00:06.0: PCI INT A -> Link[LACI] -> GSI 21 (level, low) -> IRQ 21
[ 18.424364] Intel ICH 0000:00:06.0: setting latency timer to 64
[ 18.452926] Broadcom 43xx-legacy driver loaded [ Features: PLRID, Firmware-ID: FW10 ]
[ 18.484852] yenta_cardbus 0000:02:04.1: ISA IRQ mask 0x0c38, PCI irq 18
[ 18.484858] yenta_cardbus 0000:02:04.1: Socket status: 30000006
[ 18.484863] pci_bus 0000:02: Raising subordinate bus# of parent bus (#02) from #06 to #0a
[ 18.484872] yenta_cardbus 0000:02:04.1: pcmcia: parent PCI bridge I/O window: 0x3000 - 0x7fff
[ 18.484877] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3000-0x7fff: clean.
[ 18.485869] yenta_cardbus 0000:02:04.1: pcmcia: parent PCI bridge Memory window: 0xe0100000 - 0xe17fffff
[ 18.485873] yenta_cardbus 0000:02:04.1: pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x37ffffff
[ 18.536032] AC'97 0 analog subsections not ready
[ 19.104042] intel8x0_measure_ac97_clock: measured 55410 usecs
[ 19.104047] intel8x0: clocking to 47494
[ 19.107036] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean.
[ 19.108876] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: clean.
[ 19.109648] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean.
[ 19.110290] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean.
[ 19.111116] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean.
[ 19.112572] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af: clean.
[ 19.114315] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff: clean.
[ 19.115083] pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff: clean.
[ 19.115727] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7: clean.
[ 19.116614] pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
[ 19.164048] floppy0: no floppy controllers found
[ 19.318324] lp0: using parport0 (interrupt-driven).
[ 19.970139] EXT3 FS on sda1, internal journal
[ 21.299347] type=1505 audit(1248025088.144:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2011
[ 21.368633] type=1505 audit(1248025088.216:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2015
[ 21.368848] type=1505 audit(1248025088.216:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2015
[ 21.368915] type=1505 audit(1248025088.216:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2015
[ 21.368974] type=1505 audit(1248025088.216:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2015
[ 21.576167] type=1505 audit(1248025088.424:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2020
[ 21.576429] type=1505 audit(1248025088.424:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2020
[ 21.618517] type=1505 audit(1248025088.464:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2024
[ 28.332423] input: b43legacy-phy0 as /devices/virtual/input/input9
[ 28.364075] b43legacy ssb0:0: firmware: requesting b43legacy/ucode2.fw
[ 28.492736] b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw
[ 28.514372] b43legacy ssb0:0: firmware: requesting b43legacy/b0g0initvals2.fw
[ 28.620047] b43legacy-phy0: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
[ 28.720309] b43legacy-phy0 debug: Chip initialized
[ 28.720526] b43legacy-phy0 debug: 30-bit DMA initialized
[ 28.722014] Registered led device: b43legacy-phy0:tx
[ 28.722035] Registered led device: b43legacy-phy0:rx
[ 28.722057] Registered led device: b43legacy-phy0:radio
[ 28.722099] b43legacy-phy0 debug: Wireless interface started
[ 28.728085] b43legacy-phy0 debug: Adding Interface type 2
[ 28.740106] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 29.194992] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 29.194996] Bluetooth: BNEP filters: protocol multicast
[ 29.221552] Bridge firewalling registered
[ 29.337029] b43legacy-phy0: Radio hardware status changed to DISABLED
[ 29.337688] b43legacy-phy0 debug: Radio initialized
[ 29.424022] b43legacy-phy0: Radio turned on by software
[ 29.424028] b43legacy-phy0: The hardware RF-kill button still turns the radio physically off. Press the button to turn it on.
[ 30.403348] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 32.094237] agpgart-amd64 0000:00:00.0: AGP 2.0 bridge
[ 32.094257] agpgart-amd64 0000:00:00.0: putting AGP V2 device into 4x mode
[ 32.094312] nvidia 0000:01:00.0: putting AGP V2 device into 4x mode
[ 34.545203] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 45.476034] eth0: no IPv6 routers present
Re: [Wireless] nessuna connessione alla rete hp pavilion zv5000
ho trovato questa discussione:
http://forum.ubuntu-it.org/viewtopic.php?t=281185
mi sa tanto che c'è veramente poco da fare. >:(
http://forum.ubuntu-it.org/viewtopic.php?t=281185
mi sa tanto che c'è veramente poco da fare. >:(
- [lost]-Divilinux
- Imperturbabile Insigne

- Messaggi: 3774
- Iscrizione: giovedì 12 giugno 2008, 13:06
- Località: Ipioca - Maceio - Alagoas - Brasil
- Contatti:
Re: [Wireless] nessuna connessione alla rete hp pavilion zv5000
[ 5.476901] b43-pci-bridge 0000:02:02.0: PCI INT A -> Link[LNK3] -> GSI 17 (level, low) -> IRQ 17
[ 5.480366] ssb: Sonics Silicon Backplane found on PCI device 0000:02:02.0
[ 5.921691] b44.c:v2.0
[ 5.921708] b44: Invalid MAC address found in EEPROM
[ 5.921713] b44 ssb0:1: Problem fetching invariants of chip, aborting.
[ 5.921721] b44: probe of ssb0:1 failed with error -22
Qui carica il firmware corretto, non sembrano esserci errori. Poi hai acceso e spento piu volte la scheda[ 18.291099] b43legacy-phy0: Broadcom 4301 WLAN found
[ 18.316072] b43legacy-phy0 debug: Found PHY: Analog 0, Type 1, Revision 4
[ 18.316096] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[ 18.340049] b43legacy-phy0 debug: Radio initialized
[ 18.342138] phy0: Selected rate control algorithm 'pid'
[ 18.424274] ACPI: PCI Interrupt Link [LACI] enabled at IRQ 21
[ 18.424282] Intel ICH 0000:00:06.0: PCI INT A -> Link[LACI] -> GSI 21 (level, low) -> IRQ 21
[ 18.424364] Intel ICH 0000:00:06.0: setting latency timer to 64
[ 18.452926] Broadcom 43xx-legacy driver loaded [ Features: PLRID, Firmware-ID: FW10 ]
Hai gia controllato su launchpad se sia già stato aperto un bug per questa scheda + jaunty 9.04?[ 29.337029] b43legacy-phy0: Radio hardware status changed to DISABLED
[ 29.337688] b43legacy-phy0 debug: Radio initialized
[ 29.424022] b43legacy-phy0: Radio turned on by software
[ 29.424028] b43legacy-phy0: The hardware RF-kill button still turns the radio physically off. Press the button to turn it on.
questione di seedings...
Chi c’è in linea
Visualizzano questa sezione: 0 utenti iscritti e 7 ospiti