[K3B]Problema CD-ROM

Installazione, configurazione e utilizzo di applicativi multimediali, masterizzazione, acquisizione e codec audio/video, streaming e altro.
Avatar utente
Fisher
Prode Principiante
Messaggi: 12
Iscrizione: domenica 1 novembre 2009, 12:37
Località: Rovigo

[K3B]Problema CD-ROM

Messaggio da Fisher »

Quando vado a masterizzare un DVD, K3B funziona alla perfezione, ma se decido di masterizzare un'immagine di un CD, dopo esattamente 10-11-12 secondi mi dice che:

Immagine

Codice: Seleziona tutto

Devices
-----------------------
HL-DT-ST DVD-RAM GSA-H22N 1.00 (/dev/sr0, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL) [DVD-ROM, DVD-R sequenziale, DVD-R sequenziale a doppio strato, DVD-R jump a doppio strato, DVD-RAM, DVD-RW a riscrittura limitata, DVD-RW sequenziale, DVD+RW, DVD+R, DVD+R a doppio strato, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Riscrittura limitata, Livello Jump] [%7]

System
-----------------------
K3b Version: 1.68.0
KDE Version: 4.3.2 (KDE 4.3.2)
QT Version:  4.5.2
Kernel:      2.6.31-14-generic

Used versions
-----------------------
cdrecord: 1.1.9

cdrecord
-----------------------
/usr/bin/wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.9
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   : 
Vendor_info    : 'HL-DT-ST'
Identification : 'DVD-RAM GSA-H22N'
Revision       : '1.00'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009 (CD-R)
Profile: 0x0012 (DVD-RAM) 
Profile: 0x002B (DVD+R/DL) 
Profile: 0x001B (DVD+R) 
Profile: 0x001A (DVD+RW) 
Profile: 0x0016 (DVD-R/DL layer jump recording) 
Profile: 0x0015 (DVD-R/DL sequential recording) 
Profile: 0x0014 (DVD-RW sequential recording) 
Profile: 0x0013 (DVD-RW restricted overwrite) 
Profile: 0x0011 (DVD-R sequential recording) 
Profile: 0x0010 (DVD-ROM) 
Profile: 0x000A (CD-RW) 
Profile: 0x0009 (CD-R) (current)
Profile: 0x0008 (CD-ROM) 
Profile: 0x0002 (Removable disk) 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1114112 = 1088 KB
Drive DMA Speed: 80640 kB/s 458x CD 58x DVD
FIFO size      : 4194304 = 4096 KB
Speed set to 2822 KB/s
Track 01: data   120 MB        
Total size:      120 MB (11:57.18) = 53789 sectors
Lout start:      120 MB (11:59/14) = 53789 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 5
  Is not unrestricted
  Is not erasable
  Disk sub type: Medium Type B, low Beta category (B-) (4)
  ATIP start of lead in:  -12369 (97:17/06)
  ATIP start of lead out: 359849 (79:59/74)
Disk type:    Short strategy type (Phthalocyanine or similar)
Manuf. index: 69
Manufacturer: Moser Baer India Limited
Manufacturer is guessed because of the orange forum embargo.
The orange forum likes to get money for recent information.
The information for this media may not be correct.
Blocks total: 359849 Blocks current: 359522 Blocks remaining: 305733
Starting to write CD/DVD at speed  16.0 in real SAO mode for single session.
Last chance to quit, starting real write in    2 seconds.
   1 seconds.
   0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Sending CUE sheet...
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 00 00 01 47 00 00 1B 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0E 00 00 00 00 24 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x24 Qual 0x00 (invalid field in cdb) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.002s timeout 200s
Writing pregap for track 1 at 327
write track pad data: error after 0 bytes
BFree: 1088 K BSize: 1088 K
Starting new track at sector: 477
Track 01:    0 of  120 MB written.
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 00 00 01 DD 00 00 1B 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0E 00 00 00 00 24 00 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x24 Qual 0x00 (invalid field in cdb) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.005s timeout 200s
/usr/bin/wodim: A write error occured.
/usr/bin/wodim: Please properly read the error message above.
write track data: error after 0 bytes
Writing  time:    5.056s
Average write speed 142.7x.
Fixating...
Fixating time:    0.007s
/usr/bin/wodim: fifo had 64 puts and 1 gets.
/usr/bin/wodim: fifo was 0 times empty and 0 times full, min fill was 100%.

cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/sr0 speed=16 -sao driveropts=burnfree cuefile=/home/ubuntu/Scrivania/ulaunchelf by hypno.cue fs=4m
Ultima modifica di Fisher il venerdì 11 dicembre 2009, 13:01, modificato 1 volta in totale.
Avatar utente
yves
Rampante Reduce
Rampante Reduce
Messaggi: 5422
Iscrizione: domenica 25 dicembre 2005, 2:23
Località: Argentina - BsAs
Contatti:

Re: [K3B]Permessi negati

Messaggio da yves »

Puoi fare una prova con un altro SO? Se hai Windows in dual boot prova a masterizzare un CD con lui, che masterizzi i DVD correttamente a volte non dà la certezza per i CD.
Al giorno d'oggi i cani di razza muovono la coda solo per interesse. Ma io sono un bastardo... Tuxliberty
Riscopri il PC, installa ed usa Linux ;-) - Linux != Windows Linux User # 16486 - Jabber: yvesBsAs@jabber.org
Avatar utente
grizzo94
Prode Principiante
Messaggi: 129
Iscrizione: martedì 19 maggio 2009, 15:59

Re: [K3B]Permessi negati

Messaggio da grizzo94 »

Prova ad avviarlo come root.
Vai sul Terminale e scrivi:

Codice: Seleziona tutto

sudo k3b
Ciao!
Tux Mea Lux! :)
Avatar utente
Fisher
Prode Principiante
Messaggi: 12
Iscrizione: domenica 1 novembre 2009, 12:37
Località: Rovigo

Re: [K3B]Permessi negati

Messaggio da Fisher »

Ok, ho risolto, era un problema tecnico con il supporto che usavo; ora ho un altro problema:

quando vado a creare un'immagine disco di un CD-ROM con K3b, se faccio "Informazioni supporto" mi dice tutte le informazioni tecniche del cd, ma quando vado a fare "Copia supporto.." mi si blocca dopo pochi secondi dicendo che ci sono degli errori di lettura. Se provo a fare lo stesso con Brasero mi dice addirittura che non è presente nessun CD o DVD. Provando su windows, Imgburn funziona alla perfezione.

Quando inserisco il CD in ubuntu 9.10 non lo vede nemmeno e non si apre nessuna finestra, però il masterizzatore fa il classico suono del caricamento CD/DVD. Help!!

p.s: il CD in questione è un videogioco per ps1
p.s 2: tutto ciò accade solo ed esclusivamente con i CD
Ultima modifica di Fisher il venerdì 11 dicembre 2009, 12:55, modificato 1 volta in totale.
Scrivi risposta

Ritorna a “Multimediale”

Chi c’è in linea

Visualizzano questa sezione: 0 utenti iscritti e 3 ospiti