[Wireless] Configurazione Wireless
-
giuseppevolo
- Prode Principiante
- Messaggi: 19
- Iscrizione: mercoledì 16 giugno 2010, 17:31
Re: [Wireless] Configurazione Wireless
rfkill list:
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yes
sudo lshw -C network
*-network:0
description: Network controller
product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller
vendor: Broadcom Corporation
physical id: 5
bus info: pci@0000:02:05.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: bus_master
configuration: driver=b43-pci-bridge latency=64
resources: irq:20 memory:c0204000-c0205fff
*-network:1
description: Ethernet interface
product: RTL-8139/8139C/8139C+
vendor: Realtek Semiconductor Co., Ltd.
physical id: 7
bus info: pci@0000:02:07.0
logical name: eth0
version: 10
serial: 00:0a:e4:ac:8e:39
size: 100MB/s
capacity: 100MB/s
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=full ip=192.168.1.2 latency=64 link=yes maxlatency=64 mingnt=32 multicast=yes port=MII speed=100MB/s
resources: irq:23 ioport:a000(size=256) memory:c0208000-c02080ff
*-network DISABLED
description: Wireless interface
physical id: 1
logical name: wlan0
serial: 00:14:a5:0f:42:71
capabilities: ethernet physical wireless
configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: yes
sudo lshw -C network
*-network:0
description: Network controller
product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller
vendor: Broadcom Corporation
physical id: 5
bus info: pci@0000:02:05.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: bus_master
configuration: driver=b43-pci-bridge latency=64
resources: irq:20 memory:c0204000-c0205fff
*-network:1
description: Ethernet interface
product: RTL-8139/8139C/8139C+
vendor: Realtek Semiconductor Co., Ltd.
physical id: 7
bus info: pci@0000:02:07.0
logical name: eth0
version: 10
serial: 00:0a:e4:ac:8e:39
size: 100MB/s
capacity: 100MB/s
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=full ip=192.168.1.2 latency=64 link=yes maxlatency=64 mingnt=32 multicast=yes port=MII speed=100MB/s
resources: irq:23 ioport:a000(size=256) memory:c0208000-c02080ff
*-network DISABLED
description: Wireless interface
physical id: 1
logical name: wlan0
serial: 00:14:a5:0f:42:71
capabilities: ethernet physical wireless
configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg
-
giuseppevolo
- Prode Principiante
- Messaggi: 19
- Iscrizione: mercoledì 16 giugno 2010, 17:31
Re: [Wireless] Configurazione Wireless
Quale potrebbe essere il problema?
- scolpi
- Imperturbabile Insigne

- Messaggi: 4504
- Iscrizione: giovedì 8 maggio 2008, 19:54
- Località: Folgaria (Trento)
- Contatti:
Re: [Wireless] Configurazione Wireless
sembra sia disabilitata via hardware, non hai un bottone o un interruttore scorrevole per attivarla?
Acquista il nuovo cd postumo, solo 10 euro e tutti in beneficienza, per info: www.valentinagiovagnini.it
-
giuseppevolo
- Prode Principiante
- Messaggi: 19
- Iscrizione: mercoledì 16 giugno 2010, 17:31
Re: [Wireless] Configurazione Wireless
Non sò se conosci o meno il modello, comunque c'è un bottone che premendolo dovrebbe attivarla ma nel mio caso non succede niente...
E non capisco per quale motivo...
Dove sbaglio?
E non capisco per quale motivo...
Dove sbaglio?
-
giuseppevolo
- Prode Principiante
- Messaggi: 19
- Iscrizione: mercoledì 16 giugno 2010, 17:31
Re: [Wireless] Configurazione Wireless
nel terminale digita:
tail -f /var/log/messages
dopodichè premi il pulsante un po' di volte, ma non rapidamente. se appaiono scritte nel terminale copiale.
tail -f /var/log/messages
dopodichè premi il pulsante un po' di volte, ma non rapidamente. se appaiono scritte nel terminale copiale.
-
giuseppevolo
- Prode Principiante
- Messaggi: 19
- Iscrizione: mercoledì 16 giugno 2010, 17:31
Re: [Wireless] Configurazione Wireless
questo è ciò che spunta senza risolvere il problema:
lory@lory-laptop:~$ tail -f /var/log/messages
Jun 17 11:30:03 lory-laptop kernel: [ 14.405864] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
Jun 17 11:30:03 lory-laptop kernel: [ 14.457013] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Jun 17 11:30:03 lory-laptop kernel: [ 14.462721] eth0: link down
Jun 17 11:30:03 lory-laptop kernel: [ 14.463048] ADDRCONF(NETDEV_UP): eth0: link is not ready
Jun 17 11:30:03 lory-laptop kernel: [ 14.480264] b43-phy0: Radio hardware status changed to DISABLED
Jun 17 11:30:06 lory-laptop kernel: [ 17.207995] ppdev: user-space parallel port driver
Jun 17 11:32:06 lory-laptop kernel: [ 137.683447] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Jun 17 11:32:06 lory-laptop kernel: [ 137.683999] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Jun 17 11:32:07 lory-laptop kernel: [ 138.005907] eth0: link down
Jun 17 11:32:13 lory-laptop kernel: [ 143.754988] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
lory@lory-laptop:~$ tail -f /var/log/messages
Jun 17 11:30:03 lory-laptop kernel: [ 14.405864] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
Jun 17 11:30:03 lory-laptop kernel: [ 14.457013] ADDRCONF(NETDEV_UP): wlan0: link is not ready
Jun 17 11:30:03 lory-laptop kernel: [ 14.462721] eth0: link down
Jun 17 11:30:03 lory-laptop kernel: [ 14.463048] ADDRCONF(NETDEV_UP): eth0: link is not ready
Jun 17 11:30:03 lory-laptop kernel: [ 14.480264] b43-phy0: Radio hardware status changed to DISABLED
Jun 17 11:30:06 lory-laptop kernel: [ 17.207995] ppdev: user-space parallel port driver
Jun 17 11:32:06 lory-laptop kernel: [ 137.683447] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Jun 17 11:32:06 lory-laptop kernel: [ 137.683999] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Jun 17 11:32:07 lory-laptop kernel: [ 138.005907] eth0: link down
Jun 17 11:32:13 lory-laptop kernel: [ 143.754988] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Re: [Wireless] Configurazione Wireless
vedi la riga Jun 17 11:30:03 lory-laptop kernel: [ 14.480264] b43-phy0: Radio hardware status changed to DISABLED ?
dovresti premere ancora il tasto fin che lo stato non cambia in ENABLED oppure RADIO ON.
dovresti premere ancora il tasto fin che lo stato non cambia in ENABLED oppure RADIO ON.
-
giuseppevolo
- Prode Principiante
- Messaggi: 19
- Iscrizione: mercoledì 16 giugno 2010, 17:31
Re: [Wireless] Configurazione Wireless
ho riprovato ma non succede nulla...
Non esiste un altro modo?
Non esiste un altro modo?
-
giuseppevolo
- Prode Principiante
- Messaggi: 19
- Iscrizione: mercoledì 16 giugno 2010, 17:31
Re: [Wireless] Configurazione Wireless
Ragazzi datemi una mano perchè sto uscendo pazzo!
Pleaseee
Pleaseee
Re: [Wireless] Configurazione Wireless
io non ne conosco altri. mi spiace.
-
giuseppevolo
- Prode Principiante
- Messaggi: 19
- Iscrizione: mercoledì 16 giugno 2010, 17:31
Re: [Wireless] Configurazione Wireless
grazie lo stesso del vostro aiuto.
Se magari riuscite a capire il mio tipo di problema vi prego di contattarmi.
Grazie allo staff!
Se magari riuscite a capire il mio tipo di problema vi prego di contattarmi.
Grazie allo staff!
- pablo_honey
- Entusiasta Emergente

- Messaggi: 1019
- Iscrizione: lunedì 9 novembre 2009, 13:09
- Desktop: Kde
- Distribuzione: Debian Testing i686
- Località: Italian East Coast
Re: [Wireless] Configurazione Wireless
hai provato a disabilitare l'ethernet? magari fa conflitto quella, ho letto di gente a cui succedeva
You can't always get what you want [Mick Jagger]
Chi c’è in linea
Visualizzano questa sezione: Google [Bot] e 8 ospiti
