Presario R3000 con Broadcom BCM4303

Riconoscimento, installazione e configurazione delle periferiche.
Scrivi risposta
Avatar utente
Adaron
Scoppiettante Seguace
Scoppiettante Seguace
Messaggi: 982
Iscrizione: giovedì 12 ottobre 2006, 23:53
Località: Savona

Presario R3000 con Broadcom BCM4303

Messaggio da Adaron »

Ciao a tutti,
ho appena installato Lucid su un Compaq Presario R3000 che monta una wifi Broadcom

lspci | grep Wireless

Codice: Seleziona tutto

02:02.0 Network controller: Broadcom Corporation BCM4303 802.11b Wireless LAN Controller (rev 02)
A fine installazione, dopo aver messo gli aggiornamenti per la lingua, è spuntata fuori l'icona dei driver proprietari con il b43legacy che ho installato correttamente ed attivato.
Ora però all'avvio, il LED della wireless fa un piccolo cenno e poi rimane spento.
dmesg | grep b43 da questo risultato:

Codice: Seleziona tutto

[    1.350120] b43-pci-bridge 0000:02:02.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    7.629332] b43legacy-phy0: Broadcom 4301 WLAN found
[    7.656093] b43legacy-phy0 debug: Found PHY: Analog 0, Type 1, Revision 4
[    7.656120] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2
[    7.680505] b43legacy-phy0 debug: Radio initialized
[   15.148078] b43legacy ssb0:0: firmware: requesting b43legacy/ucode2.fw
[   15.292518] b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw
[   15.308954] b43legacy ssb0:0: firmware: requesting b43legacy/b0g0initvals2.fw
[   15.461354] b43legacy-phy0: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27)
[   15.560898] b43legacy-phy0 debug: Chip initialized
[   15.561223] b43legacy-phy0 debug: 30-bit DMA initialized
[   15.563909] Registered led device: b43legacy-phy0::tx
[   15.565565] Registered led device: b43legacy-phy0::rx
[   15.566696] Registered led device: b43legacy-phy0::radio
[   15.566740] b43legacy-phy0 debug: Wireless interface started
[   15.572071] b43legacy-phy0: Radio hardware status changed to DISABLED
[   15.572078] b43legacy-phy0 debug: Radio initialized
[   15.573437] b43legacy-phy0 debug: Adding Interface type 2
[   15.616051] b43legacy-phy0: Radio turned on by software
[   15.616058] b43legacy-phy0: The hardware RF-kill button still turns the radio physically off. Press the button to turn it on.
[   15.616379] b43legacy-phy0 debug: Removing Interface type 2
[   15.616421] b43legacy-phy0 debug: Wireless interface stopped
[   15.616651] b43legacy-phy0 debug: DMA-30 0x0260 (RX) max used slots: 0/64
[   15.616704] b43legacy-phy0 debug: DMA-30 0x0200 (RX) max used slots: 0/64
[   15.616756] b43legacy-phy0 debug: DMA-30 0x02A0 (TX) max used slots: 0/128
[   15.624068] b43legacy-phy0 debug: DMA-30 0x0280 (TX) max used slots: 0/128
[   15.632032] b43legacy-phy0 debug: DMA-30 0x0260 (TX) max used slots: 0/128
[   15.640045] b43legacy-phy0 debug: DMA-30 0x0240 (TX) max used slots: 0/128
[   15.648033] b43legacy-phy0 debug: DMA-30 0x0220 (TX) max used slots: 0/128
[   15.656029] b43legacy-phy0 debug: DMA-30 0x0200 (TX) max used slots: 0/128
[   15.664080] b43legacy-phy0 debug: Radio initialized
[   15.664096] b43legacy-phy0 debug: Radio initialized
Sembra perciò che il pulsante hardware disabiliti la scheda, cosa confermata anche da rfkill list che restituisce:

Codice: Seleziona tutto

0: phy0: Wireless LAN
	Soft blocked: no
	Hard blocked: yes
ma anche dopo aver dato sudo rfkill unblock all non è cambiato nulla.

Per completezza riporto anche il risultato di lshw -C network:

Codice: Seleziona tutto

  *-network:0             
       description: Network controller
       product: BCM4303 802.11b Wireless LAN Controller
       vendor: Broadcom Corporation
       physical id: 2
       bus info: pci@0000:02:02.0
       version: 02
       width: 32 bits
       clock: 33MHz
       capabilities: bus_master
       configuration: driver=b43-pci-bridge latency=64
       resources: irq:18 memory:d0204000-d0205fff
  *-network:1
       description: Ethernet interface
       product: RTL-8139/8139C/8139C+
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 3
       bus info: pci@0000:02:03.0
       logical name: eth0
       version: 10
       serial: 00:0f:b0:0c:be:77
       size: 100MB/s
       capacity: 100MB/s
       width: 32 bits
       clock: 33MHz
       capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=full ip=10.0.0.11 latency=128 link=yes maxlatency=64 mingnt=32 multicast=yes port=MII speed=100MB/s
       resources: irq:19 ioport:a000(size=256) memory:d0208800-d02088ff
  *-network DISABLED
       description: Wireless interface
       physical id: 3
       logical name: wlan0
       serial: 00:90:4b:95:9b:a9
       capabilities: ethernet physical wireless
       configuration: broadcast=yes multicast=yes wireless=IEEE 802.11b
e non ultimo lsmod | grep b4 che restituisce:

Codice: Seleziona tutto

b43legacy             115152  0 
mac80211              204922  1 b43legacy
cfg80211              126485  2 b43legacy,mac80211
led_class               2864  1 b43legacy
b44                    25542  0 
mii                     4381  3 b44,8139too,8139cp
ssb                    37336  2 b43legacy,b44
che cosa posso provare???
[center]Io sono in te, tu sei in Me. Noi siamo Uno
io sono in te, tu sei in me. Noi siamo Uno.
Tu sei in me, io sono in Te. Noi siamo Uno.
Scrivi risposta

Ritorna a “Driver e periferiche”

Chi c’è in linea

Visualizzano questa sezione: 0 utenti iscritti e 5 ospiti