Devo connettere il mio computer a internet tramite una connessione wireless ho fatti questi passi:
- ho inserito la chiavetta
- ho acceso il pc
- appena ho acceso mi ha chiesto di inserire il nome di una connessione a cui connettermi ed ho inserito:
NATGEAR
senza protezione
windows la trovava da sola per questo ho messo solo il nome e nient'altro.
- ho connesso a NATGEAR
mi dice che è connesso, ma non va, se vado su internet non mi carica le pagine. qual'è il problema?
Chiavetta wireless
Re: Chiavetta wireless
Ciao digita da terminale il commando ifconfig e posta il risultato
ciao da denis
Re: Chiavetta wireless
imo@imo-desktop:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:1e:90:43:c2:0a
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:28 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:344 errors:0 dropped:0 overruns:0 frame:0
TX packets:344 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:27552 (27.5 KB) TX bytes:27552 (27.5 KB)
ppp0 Link encap:Point-to-Point Protocol
inet addr:151.83.224.17 P-t-P:10.64.64.64 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:4250 errors:0 dropped:0 overruns:0 frame:0
TX packets:4682 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:2256790 (2.2 MB) TX bytes:920871 (920.8 KB)
wlan0 Link encap:Ethernet HWaddr 00:02:72:8a:90:9b
inet addr:10.42.43.1 Bcast:10.42.43.255 Mask:255.255.255.0
inet6 addr: fe80::202:72ff:fe8a:909b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:51 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:12685 (12.6 KB)
eth0 Link encap:Ethernet HWaddr 00:1e:90:43:c2:0a
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:28 Base address:0x8000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:344 errors:0 dropped:0 overruns:0 frame:0
TX packets:344 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:27552 (27.5 KB) TX bytes:27552 (27.5 KB)
ppp0 Link encap:Point-to-Point Protocol
inet addr:151.83.224.17 P-t-P:10.64.64.64 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:4250 errors:0 dropped:0 overruns:0 frame:0
TX packets:4682 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
RX bytes:2256790 (2.2 MB) TX bytes:920871 (920.8 KB)
wlan0 Link encap:Ethernet HWaddr 00:02:72:8a:90:9b
inet addr:10.42.43.1 Bcast:10.42.43.255 Mask:255.255.255.0
inet6 addr: fe80::202:72ff:fe8a:909b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:51 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:12685 (12.6 KB)
Re: Chiavetta wireless
Posta anche il risultato del commando
lsusb e del commando
dmesg
lsusb e del commando
dmesg
ciao da denis
Re: Chiavetta wireless
imo@imo-desktop:~$ lsusb
Bus 002 Device 002: ID 058f:9360 Alcor Micro Corp. 8-in-1 Media Card Reader
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 020: ID 19d2:0037 ONDA Communication S.p.A.
Bus 001 Device 002: ID 0ace:1215 ZyDAS WLA-54L 802.11bg
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[ 1.300022] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.300055] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.301381] ata2.00: ATAPI: Optiarc DVD RW AD-7200S, 1.52, max UDMA/100
[ 1.303046] ata2.00: configured for UDMA/100
[ 1.342748] ata1.00: ATA-7: ST3160215AS, 3.AAC, max UDMA/133
[ 1.342753] ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 1.401079] ata1.00: configured for UDMA/133
[ 1.401219] scsi 0:0:0:0: Direct-Access ATA ST3160215AS 3.AA PQ: 0 ANSI: 5
[ 1.401402] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.401417] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 1.401516] sd 0:0:0:0: [sda] Write Protect is off
[ 1.401519] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.401544] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.401687] sda:
[ 1.403406] scsi 1:0:0:0: CD-ROM Optiarc DVD RW AD-7200S 1.52 PQ: 0 ANSI: 5
[ 1.405762] sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.405767] Uniform CD-ROM driver Revision: 3.20
[ 1.405912] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.405973] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.406131] ata6: port disabled. ignoring.
[ 1.449080] sda1 sda2 sda3 sda4
[ 1.480141] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.484051] usb 2-8: new full speed USB device using ohci_hcd and address 2
[ 1.707438] usb 2-8: configuration #1 chosen from 1 choice
[ 1.710463] scsi7 : SCSI emulation for USB Mass Storage devices
[ 1.710582] usb-storage: device found at 2
[ 1.710584] usb-storage: waiting for device to settle before scanning
[ 1.967715] EXT4-fs (sda6): mounted filesystem with ordered data mode
[ 6.077506] usb-storage: device scan complete
[ 6.080497] scsi 6:0:0:0: CD-ROM ONDA USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2
[ 6.088591] sr1: scsi-1 drive
[ 6.088738] sr 6:0:0:0: Attached scsi CD-ROM sr1
[ 6.088802] sr 6:0:0:0: Attached scsi generic sg2 type 5
[ 6.709951] usb-storage: device scan complete
[ 6.716943] scsi 7:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 6.723951] scsi 7:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 6.730949] scsi 7:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 6.737952] scsi 7:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 6.738434] sd 7:0:0:0: Attached scsi generic sg3 type 0
[ 6.738567] sd 7:0:0:1: Attached scsi generic sg4 type 0
[ 6.738694] sd 7:0:0:2: Attached scsi generic sg5 type 0
[ 6.738824] sd 7:0:0:3: Attached scsi generic sg6 type 0
[ 6.792922] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 6.803919] sd 7:0:0:1: [sdc] Attached SCSI removable disk
[ 6.814917] sd 7:0:0:2: [sdd] Attached SCSI removable disk
[ 6.825915] sd 7:0:0:3: [sde] Attached SCSI removable disk
[ 12.338308] udev: starting version 151
[ 12.374316] Adding 410616k swap on /dev/sda7. Priority:-1 extents:1 across:410616k
[ 12.530856] i2c i2c-0: nForce2 SMBus adapter at 0x4d00
[ 12.530882] i2c i2c-1: nForce2 SMBus adapter at 0x4e00
[ 12.539548] Linux agpgart interface v0.103
[ 12.650987] [drm] Initialized drm 1.1.0 20060810
[ 12.655954] lp: driver loaded but no devices found
[ 12.667696] type=1505 audit(1282336205.703:2): operation="profile_load" pid=603 name="/sbin/dhclient3"
[ 12.668386] type=1505 audit(1282336205.707:3): operation="profile_load" pid=603 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 12.668783] type=1505 audit(1282336205.707:4): operation="profile_load" pid=603 name="/usr/lib/connman/scripts/dhclient-script"
[ 12.712614] ACPI: PCI Interrupt Link [SGRU] enabled at IRQ 20
[ 12.712621] alloc irq_desc for 20 on node -1
[ 12.712623] alloc kstat_irqs on node -1
[ 12.712631] nouveau 0000:00:10.0: PCI INT A -> Link[SGRU] -> GSI 20 (level, low) -> IRQ 20
[ 12.712636] nouveau 0000:00:10.0: setting latency timer to 64
[ 12.715080] [drm] nouveau 0000:00:10.0: failed to evaluate _DSM: 5
[ 12.731142] [drm] nouveau 0000:00:10.0: Detected an NV40 generation card (0x063000a2)
[ 12.731380] [drm] nouveau 0000:00:10.0: Attempting to load BIOS image from PROM
[ 12.731384] [drm] nouveau 0000:00:10.0: ... BIOS signature not found
[ 12.731387] [drm] nouveau 0000:00:10.0: Attempting to load BIOS image from PRAMIN
[ 12.772739] [drm] nouveau 0000:00:10.0: ... appears to be valid
[ 12.772746] [drm] nouveau 0000:00:10.0: BIT BIOS found
[ 12.772750] [drm] nouveau 0000:00:10.0: Bios version 05.73.32.09
[ 12.772753] [drm] nouveau 0000:00:10.0: TMDS table script pointers not stubbed
[ 12.772756] [drm] nouveau 0000:00:10.0: BIT table 'd' not found
[ 12.772759] [drm] nouveau 0000:00:10.0: Found Display Configuration Block version 3.0
[ 12.772762] [drm] nouveau 0000:00:10.0: DCB connector table: VHER 0x30 5 10 2
[ 12.772766] [drm] nouveau 0000:00:10.0: 0: 0x00000000: type 0x00 idx 0 tag 0xff
[ 12.772769] [drm] nouveau 0000:00:10.0: 1: 0x00001161: type 0x61 idx 1 tag 0x07
[ 12.772772] [drm] nouveau 0000:00:10.0: Raw DCB entry 0: 01000110 00000023
[ 12.772779] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 0 at offset 0xCDAD
[ 12.772798] [drm] nouveau 0000:00:10.0: ======= misaligned reg 0x001020FB =======
[ 12.772862] [drm] nouveau 0000:00:10.0: ======= misaligned reg 0x001020FB =======
[ 12.772944] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 1 at offset 0xCEF9
[ 12.772946] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 2 at offset 0xCEFA
[ 12.772969] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 3 at offset 0xD07C
[ 12.772975] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 4 at offset 0xD112
[ 12.772978] [drm] nouveau 0000:00:10.0: Pointer to flat panel table invalid
[ 12.791193] [TTM] Zone kernel: Available graphics memory: 438538 kiB.
[ 12.791197] [TTM] Zone highmem: Available graphics memory: 901198 kiB.
[ 12.791209] [drm] nouveau 0000:00:10.0: 256 MiB VRAM
[ 12.792453] [drm] nouveau 0000:00:10.0: 64 MiB GART (aperture)
[ 12.792927] [drm] nouveau 0000:00:10.0: Allocating FIFO number 0
[ 12.793277] [drm] nouveau 0000:00:10.0: nouveau_channel_alloc: initialised FIFO 0
[ 12.793285] [drm] nouveau 0000:00:10.0: Initial CRTC_OWNER is 0
[ 12.793290] [drm] nouveau 0000:00:10.0: Saving VGA fonts
[ 12.829359] [drm] nouveau 0000:00:10.0: Detected a VGA connector
[ 12.830533] [drm] nouveau 0000:00:10.0: Setting dpms mode 3 on vga encoder (output 0)
[ 12.882769] psmouse serio1: ID: 10 00 64
[ 12.952343] [drm] nouveau 0000:00:10.0: allocated 1440x900 fb: 0x49000, bo f40d9800
[ 12.952545] fb0: nouveaufb frame buffer device
[ 12.952548] registered panic notifier
[ 12.952554] [drm] Initialized nouveau 0.0.15 20090420 for 0000:00:10.0 on minor 0
[ 12.952641] HDA Intel 0000:00:09.0: power state changed by ACPI to D0
[ 12.952674] HDA Intel 0000:00:09.0: power state changed by ACPI to D0
[ 12.953004] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 23
[ 12.953010] HDA Intel 0000:00:09.0: PCI INT A -> Link[LAZA] -> GSI 23 (level, low) -> IRQ 23
[ 12.953013] hda_intel: Disable MSI for Nvidia chipset
[ 12.953035] HDA Intel 0000:00:09.0: setting latency timer to 64
[ 13.042821] vga16fb: initializing
[ 13.042827] vga16fb: mapped to 0xc00a0000
[ 13.042831] vga16fb: not registering due to another framebuffer present
[ 13.045631] cfg80211: Calling CRDA to update world regulatory domain
[ 13.119854] [drm] nouveau 0000:00:10.0: Setting dpms mode 0 on vga encoder (output 0)
[ 13.119860] [drm] nouveau 0000:00:10.0: Output VGA-1 is running on CRTC 0 using output A
[ 13.126760] Console: switching to colour frame buffer device 180x56
[ 13.318135] cfg80211: World regulatory domain updated:
[ 13.318139] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.318142] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.318145] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.318147] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.318150] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.318152] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.380928] type=1505 audit(1282336206.419:5): operation="profile_load" pid=820 name="/usr/share/gdm/guest-session/Xsession"
[ 13.383054] type=1505 audit(1282336206.419:6): operation="profile_replace" pid=821 name="/sbin/dhclient3"
[ 13.383779] type=1505 audit(1282336206.419:7): operation="profile_replace" pid=821 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 13.384175] type=1505 audit(1282336206.423:8): operation="profile_replace" pid=821 name="/usr/lib/connman/scripts/dhclient-script"
[ 13.386923] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[ 13.389659] type=1505 audit(1282336206.427:9): operation="profile_load" pid=822 name="/usr/bin/evince"
[ 13.398745] type=1505 audit(1282336206.435:10): operation="profile_load" pid=822 name="/usr/bin/evince-previewer"
[ 13.408987] r8169: eth0: link down
[ 13.409223] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.409442] type=1505 audit(1282336206.447:11): operation="profile_load" pid=822 name="/usr/bin/evince-thumbnailer"
[ 13.520552] hda_codec: ALC888: BIOS auto-probing.
[ 13.624069] usb 1-4: reset high speed USB device using ehci_hcd and address 2
[ 13.764149] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:09.0/input/input5
[ 13.905336] phy0: Selected rate control algorithm 'minstrel'
[ 13.906184] zd1211rw 1-4:1.0: phy0
[ 13.906232] usbcore: registered new interface driver zd1211rw
[ 13.920159] usb 1-4: firmware: requesting zd1211/zd1211b_ub
[ 13.971658] ppdev: user-space parallel port driver
[ 14.074913] usb 1-4: firmware: requesting zd1211/zd1211b_uphr
[ 14.121833] zd1211rw 1-4:1.0: firmware version 4725
[ 14.165829] zd1211rw 1-4:1.0: zd1211b chip 0ace:1215 v4810 high 00-02-72 AL2230_RF pa0 g--NS
[ 14.168950] cfg80211: Calling CRDA for country: DE
[ 14.174827] cfg80211: Regulatory domain changed to country: DE
[ 14.174831] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 14.174834] (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 14.174836] (5150000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 14.174839] (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
[ 14.194050] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 14.411574] [drm] nouveau 0000:00:10.0: Allocating FIFO number 1
[ 14.411870] [drm] nouveau 0000:00:10.0: nouveau_channel_alloc: initialised FIFO 1
[ 14.539047] CPU0 attaching NULL sched-domain.
[ 14.539053] CPU1 attaching NULL sched-domain.
[ 14.556624] CPU0 attaching sched-domain:
[ 14.556630] domain 0: span 0-1 level MC
[ 14.556635] groups: 0 1
[ 14.556647] CPU1 attaching sched-domain:
[ 14.556649] domain 0: span 0-1 level MC
[ 14.556651] groups: 1 0
[ 16.323418] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 16.323424] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 16.323429] sr 1:0:0:0: [sr0] Add. Sense: Read of scrambled sector without authentication
[ 16.323436] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 04 00 00 00 02 00
[ 16.323448] end_request: I/O error, dev sr0, sector 4096
[ 16.354714] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 16.354721] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 16.354726] sr 1:0:0:0: [sr0] Add. Sense: Read of scrambled sector without authentication
[ 16.354734] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 04 00 00 00 02 00
[ 16.354746] end_request: I/O error, dev sr0, sector 4096
[ 16.515076] CPU0 attaching NULL sched-domain.
[ 16.515084] CPU1 attaching NULL sched-domain.
[ 16.536618] CPU0 attaching sched-domain:
[ 16.536622] domain 0: span 0-1 level MC
[ 16.536625] groups: 0 1
[ 16.536633] CPU1 attaching sched-domain:
[ 16.536635] domain 0: span 0-1 level MC
[ 16.536637] groups: 1 0
[ 18.114817] usb 1-5: USB disconnect, address 3
[ 18.263974] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 18.263980] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 18.263985] sr 1:0:0:0: [sr0] Add. Sense: Read of scrambled sector without authentication
[ 18.263992] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 02 00 00 00 02 00
[ 18.264015] end_request: I/O error, dev sr0, sector 2048
[ 18.264020] __ratelimit: 13 callbacks suppressed
[ 18.264024] Buffer I/O error on device sr0, logical block 512
[ 18.264028] Buffer I/O error on device sr0, logical block 513
[ 18.296296] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 18.296302] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 18.296306] sr 1:0:0:0: [sr0] Add. Sense: Read of scrambled sector without authentication
[ 18.296314] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 02 00 00 00 02 00
[ 18.296324] end_request: I/O error, dev sr0, sector 2048
[ 18.296329] Buffer I/O error on device sr0, logical block 512
[ 18.296333] Buffer I/O error on device sr0, logical block 513
[ 18.603255] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 18.603262] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 18.603266] sr 1:0:0:0: [sr0] Add. Sense: Read of scrambled sector without authentication
[ 18.603274] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 04 00 00 00 02 00
[ 18.603285] end_request: I/O error, dev sr0, sector 4096
[ 18.603290] Buffer I/O error on device sr0, logical block 1024
[ 18.603294] Buffer I/O error on device sr0, logical block 1025
[ 18.635666] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 18.635673] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 18.635678] sr 1:0:0:0: [sr0] Add. Sense: Read of scrambled sector without authentication
[ 18.635684] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 04 00 00 00 02 00
[ 18.635696] end_request: I/O error, dev sr0, sector 4096
[ 18.635701] Buffer I/O error on device sr0, logical block 1024
[ 18.635706] Buffer I/O error on device sr0, logical block 1025
[ 18.636908] UDF-fs: Partition marked readonly; forcing readonly mount
[ 18.671341] UDF-fs INFO UDF: Mounting volume 'ES_102944', timestamp 2001/04/02 19:09 (1078)
[ 23.328031] usb 1-5: new high speed USB device using ehci_hcd and address 5
[ 23.474372] usb 1-5: configuration #1 chosen from 1 choice
[ 23.476343] scsi8 : SCSI emulation for USB Mass Storage devices
[ 23.476629] usb-storage: device found at 5
[ 23.476632] usb-storage: waiting for device to settle before scanning
[ 23.490523] usbcore: registered new interface driver usbserial
[ 23.490781] USB Serial support registered for generic
[ 23.490918] usbcore: registered new interface driver usbserial_generic
[ 23.490921] usbserial: USB Serial Driver core
[ 23.493115] USB Serial support registered for GSM modem (1-port)
[ 23.493564] option 1-5:1.0: GSM modem (1-port) converter detected
[ 23.493877] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 23.493907] option 1-5:1.1: GSM modem (1-port) converter detected
[ 23.494077] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 23.494106] option 1-5:1.3: GSM modem (1-port) converter detected
[ 23.494279] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 23.494304] usbcore: registered new interface driver option
[ 23.494306] option: v0.7.2:USB Driver for GSM modems
[ 24.804047] wlan0: Creating new IBSS network, BSSID ca:19:c5:7f:b0:c4
[ 25.886017] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 25.930066] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 25.931364] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 25.931369] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 25.931371] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 27.168050] wlan0: no IPv6 routers present
[ 28.477893] usb-storage: device scan complete
[ 28.480009] scsi 8:0:0:0: Direct-Access ONDA MMC Storage 2.31 PQ: 0 ANSI: 2
[ 28.480794] sd 8:0:0:0: Attached scsi generic sg2 type 0
[ 28.491627] sd 8:0:0:0: [sdf] Attached SCSI removable disk
[ 57.972564] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 57.972573] usb 1-5: USB disconnect, address 5
[ 57.976223] option: option_instat_callback: error -108
[ 57.976487] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 57.976513] option 1-5:1.0: device disconnected
[ 57.976669] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 57.976690] option 1-5:1.1: device disconnected
[ 57.992733] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 57.992750] option 1-5:1.3: device disconnected
[ 58.232023] usb 1-5: new high speed USB device using ehci_hcd and address 6
[ 58.436028] usb 1-5: device descriptor read/64, error -71
[ 58.744022] usb 1-5: device descriptor read/64, error -71
[ 58.960032] usb 1-5: new high speed USB device using ehci_hcd and address 7
[ 59.536028] usb 1-5: device not accepting address 7, error -71
[ 59.648033] usb 1-5: new high speed USB device using ehci_hcd and address 8
[ 60.112031] usb 1-5: device not accepting address 8, error -71
[ 60.224032] usb 1-5: new high speed USB device using ehci_hcd and address 9
[ 60.261009] usb 1-5: configuration #1 chosen from 1 choice
[ 60.262576] option 1-5:1.0: GSM modem (1-port) converter detected
[ 60.262663] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 60.262731] option 1-5:1.1: GSM modem (1-port) converter detected
[ 60.262784] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 60.263081] scsi9 : SCSI emulation for USB Mass Storage devices
[ 60.263288] option 1-5:1.3: GSM modem (1-port) converter detected
[ 60.263369] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 60.263503] usb-storage: device found at 9
[ 60.263505] usb-storage: waiting for device to settle before scanning
[ 60.299139] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 60.299145] usb 1-5: USB disconnect, address 9
[ 60.300135] option: option_instat_callback: error -108
[ 60.300418] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 60.300443] option 1-5:1.0: device disconnected
[ 60.300590] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 60.300609] option 1-5:1.1: device disconnected
[ 60.301111] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 60.301127] option 1-5:1.3: device disconnected
[ 60.543262] usb 1-5: new high speed USB device using ehci_hcd and address 10
[ 60.748051] usb 1-5: device descriptor read/64, error -71
[ 61.432031] usb 1-5: device not accepting address 10, error -71
[ 61.544045] usb 1-5: new high speed USB device using ehci_hcd and address 11
[ 61.690526] usb 1-5: configuration #1 chosen from 1 choice
[ 61.691989] option 1-5:1.0: GSM modem (1-port) converter detected
[ 61.692092] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 61.692167] option 1-5:1.1: GSM modem (1-port) converter detected
[ 61.692230] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 61.694263] scsi10 : SCSI emulation for USB Mass Storage devices
[ 61.708063] option 1-5:1.3: GSM modem (1-port) converter detected
[ 61.708193] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 61.708302] usb-storage: device found at 11
[ 61.708304] usb-storage: waiting for device to settle before scanning
[ 61.792680] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 61.792689] usb 1-5: USB disconnect, address 11
[ 61.793053] option: option_instat_callback: error -108
[ 61.793371] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 61.793386] option 1-5:1.0: device disconnected
[ 61.793530] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 61.793543] option 1-5:1.1: device disconnected
[ 61.795086] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 61.795103] option 1-5:1.3: device disconnected
[ 62.034624] usb 1-5: new high speed USB device using ehci_hcd and address 12
[ 62.240035] usb 1-5: device descriptor read/64, error -71
[ 62.552030] usb 1-5: device descriptor read/64, error -71
[ 62.768032] usb 1-5: new high speed USB device using ehci_hcd and address 13
[ 62.914301] usb 1-5: configuration #1 chosen from 1 choice
[ 62.915937] option 1-5:1.0: GSM modem (1-port) converter detected
[ 62.916125] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 62.916246] option 1-5:1.1: GSM modem (1-port) converter detected
[ 62.916376] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 62.916543] scsi11 : SCSI emulation for USB Mass Storage devices
[ 62.916745] option 1-5:1.3: GSM modem (1-port) converter detected
[ 62.916832] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 62.916965] usb-storage: device found at 13
[ 62.916967] usb-storage: waiting for device to settle before scanning
[ 63.131074] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 63.131082] usb 1-5: USB disconnect, address 13
[ 63.131324] option: option_instat_callback: error -108
[ 63.131582] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 63.131598] option 1-5:1.0: device disconnected
[ 63.131758] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 63.131774] option 1-5:1.1: device disconnected
[ 63.135836] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 63.135852] option 1-5:1.3: device disconnected
[ 63.372035] usb 1-5: new high speed USB device using ehci_hcd and address 14
[ 63.518224] usb 1-5: configuration #1 chosen from 1 choice
[ 63.519824] option 1-5:1.0: GSM modem (1-port) converter detected
[ 63.519910] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 63.519978] option 1-5:1.1: GSM modem (1-port) converter detected
[ 63.520055] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 63.520360] scsi12 : SCSI emulation for USB Mass Storage devices
[ 63.520581] option 1-5:1.3: GSM modem (1-port) converter detected
[ 63.520668] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 63.520792] usb-storage: device found at 14
[ 63.520794] usb-storage: waiting for device to settle before scanning
[ 63.611007] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 63.611015] usb 1-5: USB disconnect, address 14
[ 63.611285] option: option_instat_callback: error -108
[ 63.611550] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 63.611564] option 1-5:1.0: device disconnected
[ 63.611728] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 63.611743] option 1-5:1.1: device disconnected
[ 63.612168] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 63.612182] option 1-5:1.3: device disconnected
[ 63.852048] usb 1-5: new high speed USB device using ehci_hcd and address 15
[ 64.056043] usb 1-5: device descriptor read/64, error -71
[ 64.364052] usb 1-5: device descriptor read/64, error -71
[ 64.580039] usb 1-5: new high speed USB device using ehci_hcd and address 16
[ 64.729661] usb 1-5: configuration #1 chosen from 1 choice
[ 64.731606] option 1-5:1.0: GSM modem (1-port) converter detected
[ 64.731691] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 64.731760] option 1-5:1.1: GSM modem (1-port) converter detected
[ 64.731813] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 64.733501] scsi13 : SCSI emulation for USB Mass Storage devices
[ 64.733691] option 1-5:1.3: GSM modem (1-port) converter detected
[ 64.733805] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 64.733870] usb-storage: device found at 16
[ 64.733872] usb-storage: waiting for device to settle before scanning
[ 65.134069] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 65.134078] usb 1-5: USB disconnect, address 16
[ 65.134417] option: option_instat_callback: error -108
[ 65.134734] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 65.134750] option 1-5:1.0: device disconnected
[ 65.134914] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 65.134929] option 1-5:1.1: device disconnected
[ 65.140737] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 65.140754] option 1-5:1.3: device disconnected
[ 65.392032] usb 1-5: new high speed USB device using ehci_hcd and address 17
[ 65.538721] usb 1-5: configuration #1 chosen from 1 choice
[ 65.540793] option 1-5:1.0: GSM modem (1-port) converter detected
[ 65.540889] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 65.540958] option 1-5:1.1: GSM modem (1-port) converter detected
[ 65.541015] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 65.541323] scsi14 : SCSI emulation for USB Mass Storage devices
[ 65.541559] option 1-5:1.3: GSM modem (1-port) converter detected
[ 65.541669] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 65.541815] usb-storage: device found at 17
[ 65.541817] usb-storage: waiting for device to settle before scanning
[ 65.613985] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 65.613994] usb 1-5: USB disconnect, address 17
[ 65.614380] option: option_instat_callback: error -108
[ 65.614692] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 65.614707] option 1-5:1.0: device disconnected
[ 65.614867] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 65.614882] option 1-5:1.1: device disconnected
[ 65.615290] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 65.615305] option 1-5:1.3: device disconnected
[ 65.852033] usb 1-5: new high speed USB device using ehci_hcd and address 18
[ 66.056043] usb 1-5: device descriptor read/64, error -71
[ 66.368033] usb 1-5: device descriptor read/64, error -71
[ 66.584032] usb 1-5: new high speed USB device using ehci_hcd and address 19
[ 66.730002] usb 1-5: configuration #1 chosen from 1 choice
[ 66.731754] option 1-5:1.0: GSM modem (1-port) converter detected
[ 66.731909] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 66.732016] option 1-5:1.1: GSM modem (1-port) converter detected
[ 66.732159] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 66.732320] scsi15 : SCSI emulation for USB Mass Storage devices
[ 66.732542] option 1-5:1.3: GSM modem (1-port) converter detected
[ 66.732626] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 66.732763] usb-storage: device found at 19
[ 66.732765] usb-storage: waiting for device to settle before scanning
[ 66.832250] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 66.832259] usb 1-5: USB disconnect, address 19
[ 66.832533] option: option_instat_callback: error -108
[ 66.832829] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 66.832845] option 1-5:1.0: device disconnected
[ 66.833019] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 66.833033] option 1-5:1.1: device disconnected
[ 66.838753] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 66.838769] option 1-5:1.3: device disconnected
[ 67.076065] usb 1-5: new high speed USB device using ehci_hcd and address 20
[ 67.221963] usb 1-5: configuration #1 chosen from 1 choice
[ 67.223913] option 1-5:1.0: GSM modem (1-port) converter detected
[ 67.223999] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 67.224504] option 1-5:1.1: GSM modem (1-port) converter detected
[ 67.224585] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 67.224853] scsi16 : SCSI emulation for USB Mass Storage devices
[ 67.225081] option 1-5:1.3: GSM modem (1-port) converter detected
[ 67.225172] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 67.225304] usb-storage: device found at 20
[ 67.225306] usb-storage: waiting for device to settle before scanning
[ 72.225480] usb-storage: device scan complete
[ 72.227453] scsi 16:0:0:0: Direct-Access ONDA MMC Storage 2.31 PQ: 0 ANSI: 2
[ 72.229790] sd 16:0:0:0: Attached scsi generic sg2 type 0
[ 72.237729] sd 16:0:0:0: [sdf] Attached SCSI removable disk
[ 97.734109] PPP BSD Compression module registered
[ 97.737952] PPP Deflate Compression module registered
[ 355.000022] wlan0: No active IBSS STAs - trying to scan for other IBSS networks with same SSID (merge)
[ 415.000026] wlan0: No active IBSS STAs - trying to scan for other IBSS networks with same SSID (merge)
[ 475.000029] wlan0: No active IBSS STAs - trying to scan for other IBSS networks with same SSID (merge)
Bus 002 Device 002: ID 058f:9360 Alcor Micro Corp. 8-in-1 Media Card Reader
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 020: ID 19d2:0037 ONDA Communication S.p.A.
Bus 001 Device 002: ID 0ace:1215 ZyDAS WLA-54L 802.11bg
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[ 1.300022] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.300055] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 1.301381] ata2.00: ATAPI: Optiarc DVD RW AD-7200S, 1.52, max UDMA/100
[ 1.303046] ata2.00: configured for UDMA/100
[ 1.342748] ata1.00: ATA-7: ST3160215AS, 3.AAC, max UDMA/133
[ 1.342753] ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 1.401079] ata1.00: configured for UDMA/133
[ 1.401219] scsi 0:0:0:0: Direct-Access ATA ST3160215AS 3.AA PQ: 0 ANSI: 5
[ 1.401402] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.401417] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 1.401516] sd 0:0:0:0: [sda] Write Protect is off
[ 1.401519] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.401544] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.401687] sda:
[ 1.403406] scsi 1:0:0:0: CD-ROM Optiarc DVD RW AD-7200S 1.52 PQ: 0 ANSI: 5
[ 1.405762] sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.405767] Uniform CD-ROM driver Revision: 3.20
[ 1.405912] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.405973] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 1.406131] ata6: port disabled. ignoring.
[ 1.449080] sda1 sda2 sda3 sda4
[ 1.480141] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.484051] usb 2-8: new full speed USB device using ohci_hcd and address 2
[ 1.707438] usb 2-8: configuration #1 chosen from 1 choice
[ 1.710463] scsi7 : SCSI emulation for USB Mass Storage devices
[ 1.710582] usb-storage: device found at 2
[ 1.710584] usb-storage: waiting for device to settle before scanning
[ 1.967715] EXT4-fs (sda6): mounted filesystem with ordered data mode
[ 6.077506] usb-storage: device scan complete
[ 6.080497] scsi 6:0:0:0: CD-ROM ONDA USB SCSI CD-ROM 2.31 PQ: 0 ANSI: 2
[ 6.088591] sr1: scsi-1 drive
[ 6.088738] sr 6:0:0:0: Attached scsi CD-ROM sr1
[ 6.088802] sr 6:0:0:0: Attached scsi generic sg2 type 5
[ 6.709951] usb-storage: device scan complete
[ 6.716943] scsi 7:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 6.723951] scsi 7:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 6.730949] scsi 7:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 6.737952] scsi 7:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 6.738434] sd 7:0:0:0: Attached scsi generic sg3 type 0
[ 6.738567] sd 7:0:0:1: Attached scsi generic sg4 type 0
[ 6.738694] sd 7:0:0:2: Attached scsi generic sg5 type 0
[ 6.738824] sd 7:0:0:3: Attached scsi generic sg6 type 0
[ 6.792922] sd 7:0:0:0: [sdb] Attached SCSI removable disk
[ 6.803919] sd 7:0:0:1: [sdc] Attached SCSI removable disk
[ 6.814917] sd 7:0:0:2: [sdd] Attached SCSI removable disk
[ 6.825915] sd 7:0:0:3: [sde] Attached SCSI removable disk
[ 12.338308] udev: starting version 151
[ 12.374316] Adding 410616k swap on /dev/sda7. Priority:-1 extents:1 across:410616k
[ 12.530856] i2c i2c-0: nForce2 SMBus adapter at 0x4d00
[ 12.530882] i2c i2c-1: nForce2 SMBus adapter at 0x4e00
[ 12.539548] Linux agpgart interface v0.103
[ 12.650987] [drm] Initialized drm 1.1.0 20060810
[ 12.655954] lp: driver loaded but no devices found
[ 12.667696] type=1505 audit(1282336205.703:2): operation="profile_load" pid=603 name="/sbin/dhclient3"
[ 12.668386] type=1505 audit(1282336205.707:3): operation="profile_load" pid=603 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 12.668783] type=1505 audit(1282336205.707:4): operation="profile_load" pid=603 name="/usr/lib/connman/scripts/dhclient-script"
[ 12.712614] ACPI: PCI Interrupt Link [SGRU] enabled at IRQ 20
[ 12.712621] alloc irq_desc for 20 on node -1
[ 12.712623] alloc kstat_irqs on node -1
[ 12.712631] nouveau 0000:00:10.0: PCI INT A -> Link[SGRU] -> GSI 20 (level, low) -> IRQ 20
[ 12.712636] nouveau 0000:00:10.0: setting latency timer to 64
[ 12.715080] [drm] nouveau 0000:00:10.0: failed to evaluate _DSM: 5
[ 12.731142] [drm] nouveau 0000:00:10.0: Detected an NV40 generation card (0x063000a2)
[ 12.731380] [drm] nouveau 0000:00:10.0: Attempting to load BIOS image from PROM
[ 12.731384] [drm] nouveau 0000:00:10.0: ... BIOS signature not found
[ 12.731387] [drm] nouveau 0000:00:10.0: Attempting to load BIOS image from PRAMIN
[ 12.772739] [drm] nouveau 0000:00:10.0: ... appears to be valid
[ 12.772746] [drm] nouveau 0000:00:10.0: BIT BIOS found
[ 12.772750] [drm] nouveau 0000:00:10.0: Bios version 05.73.32.09
[ 12.772753] [drm] nouveau 0000:00:10.0: TMDS table script pointers not stubbed
[ 12.772756] [drm] nouveau 0000:00:10.0: BIT table 'd' not found
[ 12.772759] [drm] nouveau 0000:00:10.0: Found Display Configuration Block version 3.0
[ 12.772762] [drm] nouveau 0000:00:10.0: DCB connector table: VHER 0x30 5 10 2
[ 12.772766] [drm] nouveau 0000:00:10.0: 0: 0x00000000: type 0x00 idx 0 tag 0xff
[ 12.772769] [drm] nouveau 0000:00:10.0: 1: 0x00001161: type 0x61 idx 1 tag 0x07
[ 12.772772] [drm] nouveau 0000:00:10.0: Raw DCB entry 0: 01000110 00000023
[ 12.772779] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 0 at offset 0xCDAD
[ 12.772798] [drm] nouveau 0000:00:10.0: ======= misaligned reg 0x001020FB =======
[ 12.772862] [drm] nouveau 0000:00:10.0: ======= misaligned reg 0x001020FB =======
[ 12.772944] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 1 at offset 0xCEF9
[ 12.772946] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 2 at offset 0xCEFA
[ 12.772969] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 3 at offset 0xD07C
[ 12.772975] [drm] nouveau 0000:00:10.0: Parsing VBIOS init table 4 at offset 0xD112
[ 12.772978] [drm] nouveau 0000:00:10.0: Pointer to flat panel table invalid
[ 12.791193] [TTM] Zone kernel: Available graphics memory: 438538 kiB.
[ 12.791197] [TTM] Zone highmem: Available graphics memory: 901198 kiB.
[ 12.791209] [drm] nouveau 0000:00:10.0: 256 MiB VRAM
[ 12.792453] [drm] nouveau 0000:00:10.0: 64 MiB GART (aperture)
[ 12.792927] [drm] nouveau 0000:00:10.0: Allocating FIFO number 0
[ 12.793277] [drm] nouveau 0000:00:10.0: nouveau_channel_alloc: initialised FIFO 0
[ 12.793285] [drm] nouveau 0000:00:10.0: Initial CRTC_OWNER is 0
[ 12.793290] [drm] nouveau 0000:00:10.0: Saving VGA fonts
[ 12.829359] [drm] nouveau 0000:00:10.0: Detected a VGA connector
[ 12.830533] [drm] nouveau 0000:00:10.0: Setting dpms mode 3 on vga encoder (output 0)
[ 12.882769] psmouse serio1: ID: 10 00 64
[ 12.952343] [drm] nouveau 0000:00:10.0: allocated 1440x900 fb: 0x49000, bo f40d9800
[ 12.952545] fb0: nouveaufb frame buffer device
[ 12.952548] registered panic notifier
[ 12.952554] [drm] Initialized nouveau 0.0.15 20090420 for 0000:00:10.0 on minor 0
[ 12.952641] HDA Intel 0000:00:09.0: power state changed by ACPI to D0
[ 12.952674] HDA Intel 0000:00:09.0: power state changed by ACPI to D0
[ 12.953004] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 23
[ 12.953010] HDA Intel 0000:00:09.0: PCI INT A -> Link[LAZA] -> GSI 23 (level, low) -> IRQ 23
[ 12.953013] hda_intel: Disable MSI for Nvidia chipset
[ 12.953035] HDA Intel 0000:00:09.0: setting latency timer to 64
[ 13.042821] vga16fb: initializing
[ 13.042827] vga16fb: mapped to 0xc00a0000
[ 13.042831] vga16fb: not registering due to another framebuffer present
[ 13.045631] cfg80211: Calling CRDA to update world regulatory domain
[ 13.119854] [drm] nouveau 0000:00:10.0: Setting dpms mode 0 on vga encoder (output 0)
[ 13.119860] [drm] nouveau 0000:00:10.0: Output VGA-1 is running on CRTC 0 using output A
[ 13.126760] Console: switching to colour frame buffer device 180x56
[ 13.318135] cfg80211: World regulatory domain updated:
[ 13.318139] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 13.318142] (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.318145] (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.318147] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 13.318150] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.318152] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 13.380928] type=1505 audit(1282336206.419:5): operation="profile_load" pid=820 name="/usr/share/gdm/guest-session/Xsession"
[ 13.383054] type=1505 audit(1282336206.419:6): operation="profile_replace" pid=821 name="/sbin/dhclient3"
[ 13.383779] type=1505 audit(1282336206.419:7): operation="profile_replace" pid=821 name="/usr/lib/NetworkManager/nm-dhcp-client.action"
[ 13.384175] type=1505 audit(1282336206.423:8): operation="profile_replace" pid=821 name="/usr/lib/connman/scripts/dhclient-script"
[ 13.386923] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
[ 13.389659] type=1505 audit(1282336206.427:9): operation="profile_load" pid=822 name="/usr/bin/evince"
[ 13.398745] type=1505 audit(1282336206.435:10): operation="profile_load" pid=822 name="/usr/bin/evince-previewer"
[ 13.408987] r8169: eth0: link down
[ 13.409223] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.409442] type=1505 audit(1282336206.447:11): operation="profile_load" pid=822 name="/usr/bin/evince-thumbnailer"
[ 13.520552] hda_codec: ALC888: BIOS auto-probing.
[ 13.624069] usb 1-4: reset high speed USB device using ehci_hcd and address 2
[ 13.764149] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:09.0/input/input5
[ 13.905336] phy0: Selected rate control algorithm 'minstrel'
[ 13.906184] zd1211rw 1-4:1.0: phy0
[ 13.906232] usbcore: registered new interface driver zd1211rw
[ 13.920159] usb 1-4: firmware: requesting zd1211/zd1211b_ub
[ 13.971658] ppdev: user-space parallel port driver
[ 14.074913] usb 1-4: firmware: requesting zd1211/zd1211b_uphr
[ 14.121833] zd1211rw 1-4:1.0: firmware version 4725
[ 14.165829] zd1211rw 1-4:1.0: zd1211b chip 0ace:1215 v4810 high 00-02-72 AL2230_RF pa0 g--NS
[ 14.168950] cfg80211: Calling CRDA for country: DE
[ 14.174827] cfg80211: Regulatory domain changed to country: DE
[ 14.174831] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 14.174834] (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 14.174836] (5150000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 14.174839] (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
[ 14.194050] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 14.411574] [drm] nouveau 0000:00:10.0: Allocating FIFO number 1
[ 14.411870] [drm] nouveau 0000:00:10.0: nouveau_channel_alloc: initialised FIFO 1
[ 14.539047] CPU0 attaching NULL sched-domain.
[ 14.539053] CPU1 attaching NULL sched-domain.
[ 14.556624] CPU0 attaching sched-domain:
[ 14.556630] domain 0: span 0-1 level MC
[ 14.556635] groups: 0 1
[ 14.556647] CPU1 attaching sched-domain:
[ 14.556649] domain 0: span 0-1 level MC
[ 14.556651] groups: 1 0
[ 16.323418] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 16.323424] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 16.323429] sr 1:0:0:0: [sr0] Add. Sense: Read of scrambled sector without authentication
[ 16.323436] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 04 00 00 00 02 00
[ 16.323448] end_request: I/O error, dev sr0, sector 4096
[ 16.354714] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 16.354721] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 16.354726] sr 1:0:0:0: [sr0] Add. Sense: Read of scrambled sector without authentication
[ 16.354734] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 04 00 00 00 02 00
[ 16.354746] end_request: I/O error, dev sr0, sector 4096
[ 16.515076] CPU0 attaching NULL sched-domain.
[ 16.515084] CPU1 attaching NULL sched-domain.
[ 16.536618] CPU0 attaching sched-domain:
[ 16.536622] domain 0: span 0-1 level MC
[ 16.536625] groups: 0 1
[ 16.536633] CPU1 attaching sched-domain:
[ 16.536635] domain 0: span 0-1 level MC
[ 16.536637] groups: 1 0
[ 18.114817] usb 1-5: USB disconnect, address 3
[ 18.263974] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 18.263980] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 18.263985] sr 1:0:0:0: [sr0] Add. Sense: Read of scrambled sector without authentication
[ 18.263992] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 02 00 00 00 02 00
[ 18.264015] end_request: I/O error, dev sr0, sector 2048
[ 18.264020] __ratelimit: 13 callbacks suppressed
[ 18.264024] Buffer I/O error on device sr0, logical block 512
[ 18.264028] Buffer I/O error on device sr0, logical block 513
[ 18.296296] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 18.296302] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 18.296306] sr 1:0:0:0: [sr0] Add. Sense: Read of scrambled sector without authentication
[ 18.296314] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 02 00 00 00 02 00
[ 18.296324] end_request: I/O error, dev sr0, sector 2048
[ 18.296329] Buffer I/O error on device sr0, logical block 512
[ 18.296333] Buffer I/O error on device sr0, logical block 513
[ 18.603255] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 18.603262] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 18.603266] sr 1:0:0:0: [sr0] Add. Sense: Read of scrambled sector without authentication
[ 18.603274] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 04 00 00 00 02 00
[ 18.603285] end_request: I/O error, dev sr0, sector 4096
[ 18.603290] Buffer I/O error on device sr0, logical block 1024
[ 18.603294] Buffer I/O error on device sr0, logical block 1025
[ 18.635666] sr 1:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 18.635673] sr 1:0:0:0: [sr0] Sense Key : Illegal Request [current]
[ 18.635678] sr 1:0:0:0: [sr0] Add. Sense: Read of scrambled sector without authentication
[ 18.635684] sr 1:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 04 00 00 00 02 00
[ 18.635696] end_request: I/O error, dev sr0, sector 4096
[ 18.635701] Buffer I/O error on device sr0, logical block 1024
[ 18.635706] Buffer I/O error on device sr0, logical block 1025
[ 18.636908] UDF-fs: Partition marked readonly; forcing readonly mount
[ 18.671341] UDF-fs INFO UDF: Mounting volume 'ES_102944', timestamp 2001/04/02 19:09 (1078)
[ 23.328031] usb 1-5: new high speed USB device using ehci_hcd and address 5
[ 23.474372] usb 1-5: configuration #1 chosen from 1 choice
[ 23.476343] scsi8 : SCSI emulation for USB Mass Storage devices
[ 23.476629] usb-storage: device found at 5
[ 23.476632] usb-storage: waiting for device to settle before scanning
[ 23.490523] usbcore: registered new interface driver usbserial
[ 23.490781] USB Serial support registered for generic
[ 23.490918] usbcore: registered new interface driver usbserial_generic
[ 23.490921] usbserial: USB Serial Driver core
[ 23.493115] USB Serial support registered for GSM modem (1-port)
[ 23.493564] option 1-5:1.0: GSM modem (1-port) converter detected
[ 23.493877] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 23.493907] option 1-5:1.1: GSM modem (1-port) converter detected
[ 23.494077] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 23.494106] option 1-5:1.3: GSM modem (1-port) converter detected
[ 23.494279] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 23.494304] usbcore: registered new interface driver option
[ 23.494306] option: v0.7.2:USB Driver for GSM modems
[ 24.804047] wlan0: Creating new IBSS network, BSSID ca:19:c5:7f:b0:c4
[ 25.886017] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 25.930066] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 25.931364] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 25.931369] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[ 25.931371] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 27.168050] wlan0: no IPv6 routers present
[ 28.477893] usb-storage: device scan complete
[ 28.480009] scsi 8:0:0:0: Direct-Access ONDA MMC Storage 2.31 PQ: 0 ANSI: 2
[ 28.480794] sd 8:0:0:0: Attached scsi generic sg2 type 0
[ 28.491627] sd 8:0:0:0: [sdf] Attached SCSI removable disk
[ 57.972564] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 57.972573] usb 1-5: USB disconnect, address 5
[ 57.976223] option: option_instat_callback: error -108
[ 57.976487] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 57.976513] option 1-5:1.0: device disconnected
[ 57.976669] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 57.976690] option 1-5:1.1: device disconnected
[ 57.992733] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 57.992750] option 1-5:1.3: device disconnected
[ 58.232023] usb 1-5: new high speed USB device using ehci_hcd and address 6
[ 58.436028] usb 1-5: device descriptor read/64, error -71
[ 58.744022] usb 1-5: device descriptor read/64, error -71
[ 58.960032] usb 1-5: new high speed USB device using ehci_hcd and address 7
[ 59.536028] usb 1-5: device not accepting address 7, error -71
[ 59.648033] usb 1-5: new high speed USB device using ehci_hcd and address 8
[ 60.112031] usb 1-5: device not accepting address 8, error -71
[ 60.224032] usb 1-5: new high speed USB device using ehci_hcd and address 9
[ 60.261009] usb 1-5: configuration #1 chosen from 1 choice
[ 60.262576] option 1-5:1.0: GSM modem (1-port) converter detected
[ 60.262663] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 60.262731] option 1-5:1.1: GSM modem (1-port) converter detected
[ 60.262784] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 60.263081] scsi9 : SCSI emulation for USB Mass Storage devices
[ 60.263288] option 1-5:1.3: GSM modem (1-port) converter detected
[ 60.263369] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 60.263503] usb-storage: device found at 9
[ 60.263505] usb-storage: waiting for device to settle before scanning
[ 60.299139] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 60.299145] usb 1-5: USB disconnect, address 9
[ 60.300135] option: option_instat_callback: error -108
[ 60.300418] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 60.300443] option 1-5:1.0: device disconnected
[ 60.300590] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 60.300609] option 1-5:1.1: device disconnected
[ 60.301111] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 60.301127] option 1-5:1.3: device disconnected
[ 60.543262] usb 1-5: new high speed USB device using ehci_hcd and address 10
[ 60.748051] usb 1-5: device descriptor read/64, error -71
[ 61.432031] usb 1-5: device not accepting address 10, error -71
[ 61.544045] usb 1-5: new high speed USB device using ehci_hcd and address 11
[ 61.690526] usb 1-5: configuration #1 chosen from 1 choice
[ 61.691989] option 1-5:1.0: GSM modem (1-port) converter detected
[ 61.692092] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 61.692167] option 1-5:1.1: GSM modem (1-port) converter detected
[ 61.692230] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 61.694263] scsi10 : SCSI emulation for USB Mass Storage devices
[ 61.708063] option 1-5:1.3: GSM modem (1-port) converter detected
[ 61.708193] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 61.708302] usb-storage: device found at 11
[ 61.708304] usb-storage: waiting for device to settle before scanning
[ 61.792680] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 61.792689] usb 1-5: USB disconnect, address 11
[ 61.793053] option: option_instat_callback: error -108
[ 61.793371] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 61.793386] option 1-5:1.0: device disconnected
[ 61.793530] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 61.793543] option 1-5:1.1: device disconnected
[ 61.795086] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 61.795103] option 1-5:1.3: device disconnected
[ 62.034624] usb 1-5: new high speed USB device using ehci_hcd and address 12
[ 62.240035] usb 1-5: device descriptor read/64, error -71
[ 62.552030] usb 1-5: device descriptor read/64, error -71
[ 62.768032] usb 1-5: new high speed USB device using ehci_hcd and address 13
[ 62.914301] usb 1-5: configuration #1 chosen from 1 choice
[ 62.915937] option 1-5:1.0: GSM modem (1-port) converter detected
[ 62.916125] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 62.916246] option 1-5:1.1: GSM modem (1-port) converter detected
[ 62.916376] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 62.916543] scsi11 : SCSI emulation for USB Mass Storage devices
[ 62.916745] option 1-5:1.3: GSM modem (1-port) converter detected
[ 62.916832] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 62.916965] usb-storage: device found at 13
[ 62.916967] usb-storage: waiting for device to settle before scanning
[ 63.131074] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 63.131082] usb 1-5: USB disconnect, address 13
[ 63.131324] option: option_instat_callback: error -108
[ 63.131582] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 63.131598] option 1-5:1.0: device disconnected
[ 63.131758] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 63.131774] option 1-5:1.1: device disconnected
[ 63.135836] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 63.135852] option 1-5:1.3: device disconnected
[ 63.372035] usb 1-5: new high speed USB device using ehci_hcd and address 14
[ 63.518224] usb 1-5: configuration #1 chosen from 1 choice
[ 63.519824] option 1-5:1.0: GSM modem (1-port) converter detected
[ 63.519910] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 63.519978] option 1-5:1.1: GSM modem (1-port) converter detected
[ 63.520055] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 63.520360] scsi12 : SCSI emulation for USB Mass Storage devices
[ 63.520581] option 1-5:1.3: GSM modem (1-port) converter detected
[ 63.520668] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 63.520792] usb-storage: device found at 14
[ 63.520794] usb-storage: waiting for device to settle before scanning
[ 63.611007] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 63.611015] usb 1-5: USB disconnect, address 14
[ 63.611285] option: option_instat_callback: error -108
[ 63.611550] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 63.611564] option 1-5:1.0: device disconnected
[ 63.611728] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 63.611743] option 1-5:1.1: device disconnected
[ 63.612168] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 63.612182] option 1-5:1.3: device disconnected
[ 63.852048] usb 1-5: new high speed USB device using ehci_hcd and address 15
[ 64.056043] usb 1-5: device descriptor read/64, error -71
[ 64.364052] usb 1-5: device descriptor read/64, error -71
[ 64.580039] usb 1-5: new high speed USB device using ehci_hcd and address 16
[ 64.729661] usb 1-5: configuration #1 chosen from 1 choice
[ 64.731606] option 1-5:1.0: GSM modem (1-port) converter detected
[ 64.731691] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 64.731760] option 1-5:1.1: GSM modem (1-port) converter detected
[ 64.731813] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 64.733501] scsi13 : SCSI emulation for USB Mass Storage devices
[ 64.733691] option 1-5:1.3: GSM modem (1-port) converter detected
[ 64.733805] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 64.733870] usb-storage: device found at 16
[ 64.733872] usb-storage: waiting for device to settle before scanning
[ 65.134069] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 65.134078] usb 1-5: USB disconnect, address 16
[ 65.134417] option: option_instat_callback: error -108
[ 65.134734] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 65.134750] option 1-5:1.0: device disconnected
[ 65.134914] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 65.134929] option 1-5:1.1: device disconnected
[ 65.140737] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 65.140754] option 1-5:1.3: device disconnected
[ 65.392032] usb 1-5: new high speed USB device using ehci_hcd and address 17
[ 65.538721] usb 1-5: configuration #1 chosen from 1 choice
[ 65.540793] option 1-5:1.0: GSM modem (1-port) converter detected
[ 65.540889] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 65.540958] option 1-5:1.1: GSM modem (1-port) converter detected
[ 65.541015] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 65.541323] scsi14 : SCSI emulation for USB Mass Storage devices
[ 65.541559] option 1-5:1.3: GSM modem (1-port) converter detected
[ 65.541669] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 65.541815] usb-storage: device found at 17
[ 65.541817] usb-storage: waiting for device to settle before scanning
[ 65.613985] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 65.613994] usb 1-5: USB disconnect, address 17
[ 65.614380] option: option_instat_callback: error -108
[ 65.614692] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 65.614707] option 1-5:1.0: device disconnected
[ 65.614867] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 65.614882] option 1-5:1.1: device disconnected
[ 65.615290] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 65.615305] option 1-5:1.3: device disconnected
[ 65.852033] usb 1-5: new high speed USB device using ehci_hcd and address 18
[ 66.056043] usb 1-5: device descriptor read/64, error -71
[ 66.368033] usb 1-5: device descriptor read/64, error -71
[ 66.584032] usb 1-5: new high speed USB device using ehci_hcd and address 19
[ 66.730002] usb 1-5: configuration #1 chosen from 1 choice
[ 66.731754] option 1-5:1.0: GSM modem (1-port) converter detected
[ 66.731909] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 66.732016] option 1-5:1.1: GSM modem (1-port) converter detected
[ 66.732159] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 66.732320] scsi15 : SCSI emulation for USB Mass Storage devices
[ 66.732542] option 1-5:1.3: GSM modem (1-port) converter detected
[ 66.732626] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 66.732763] usb-storage: device found at 19
[ 66.732765] usb-storage: waiting for device to settle before scanning
[ 66.832250] hub 1-0:1.0: port 5 disabled by hub (EMI?), re-enabling...
[ 66.832259] usb 1-5: USB disconnect, address 19
[ 66.832533] option: option_instat_callback: error -108
[ 66.832829] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[ 66.832845] option 1-5:1.0: device disconnected
[ 66.833019] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[ 66.833033] option 1-5:1.1: device disconnected
[ 66.838753] option1 ttyUSB2: GSM modem (1-port) converter now disconnected from ttyUSB2
[ 66.838769] option 1-5:1.3: device disconnected
[ 67.076065] usb 1-5: new high speed USB device using ehci_hcd and address 20
[ 67.221963] usb 1-5: configuration #1 chosen from 1 choice
[ 67.223913] option 1-5:1.0: GSM modem (1-port) converter detected
[ 67.223999] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB0
[ 67.224504] option 1-5:1.1: GSM modem (1-port) converter detected
[ 67.224585] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB1
[ 67.224853] scsi16 : SCSI emulation for USB Mass Storage devices
[ 67.225081] option 1-5:1.3: GSM modem (1-port) converter detected
[ 67.225172] usb 1-5: GSM modem (1-port) converter now attached to ttyUSB2
[ 67.225304] usb-storage: device found at 20
[ 67.225306] usb-storage: waiting for device to settle before scanning
[ 72.225480] usb-storage: device scan complete
[ 72.227453] scsi 16:0:0:0: Direct-Access ONDA MMC Storage 2.31 PQ: 0 ANSI: 2
[ 72.229790] sd 16:0:0:0: Attached scsi generic sg2 type 0
[ 72.237729] sd 16:0:0:0: [sdf] Attached SCSI removable disk
[ 97.734109] PPP BSD Compression module registered
[ 97.737952] PPP Deflate Compression module registered
[ 355.000022] wlan0: No active IBSS STAs - trying to scan for other IBSS networks with same SSID (merge)
[ 415.000026] wlan0: No active IBSS STAs - trying to scan for other IBSS networks with same SSID (merge)
[ 475.000029] wlan0: No active IBSS STAs - trying to scan for other IBSS networks with same SSID (merge)
Chi c’è in linea
Visualizzano questa sezione: 0 utenti iscritti e 5 ospiti
