[Usb] USB Disconnect: cannot disable port 1 (err = -19)

Riconoscimento, installazione e configurazione delle periferiche.
Scrivi risposta
Avatar utente
lain
Prode Principiante
Messaggi: 69
Iscrizione: giovedì 2 settembre 2010, 19:50

[Usb] USB Disconnect: cannot disable port 1 (err = -19)

Messaggio da lain »

Ciao a tutti.
è la seconda volta che da stamane che ad un certo punto (senza nessuna azione apparentemente strana) che il mio portatile non vede più le periferiche USB.
Praticamente ad un certo punto il mio mouse smette di funzionare (si spegne la lucetta), così per le pennette e qualsiasi periferita collegata alle mie usb.

L'errore curioso quello presente nel dmesg, di seguito:

Codice: Seleziona tutto

mauri@mauri-laptop:~$ uname -a
Linux mauri-laptop 2.6.35-22-generic #35-Ubuntu SMP Sat Oct 16 20:45:36 UTC 2010 x86_64 GNU/Linux
mauri@mauri-laptop:~$ dmesg
[....]
[11539.535826] usb 2-1.1: USB disconnect, address 3
[11539.855027] usb 2-1.1: new low speed USB device using ehci_hcd and address 5
[11539.954676] ehci_hcd 0000:00:1d.0: fatal error
[11539.961519] ehci_hcd 0000:00:1d.0: force halt; handshake ffffc90000c72824 00004000 00004000 -> -110
[11539.961526] ehci_hcd 0000:00:1d.0: HC died; cleaning up
[11539.973391] usb 2-1.1: device descriptor read/all, error -108
[11539.973400] hub 2-1:1.0: cannot disable port 1 (err = -19)
[11539.973418] hub 2-1:1.0: cannot reset port 1 (err = -19)
[11539.973425] hub 2-1:1.0: cannot disable port 1 (err = -19)
[11539.973437] hub 2-1:1.0: cannot reset port 1 (err = -19)
[11539.973444] hub 2-1:1.0: cannot disable port 1 (err = -19)
[11539.973454] hub 2-1:1.0: cannot reset port 1 (err = -19)
[11539.973460] hub 2-1:1.0: cannot disable port 1 (err = -19)
[11539.973466] hub 2-1:1.0: unable to enumerate USB device on port 1
[11539.973472] hub 2-1:1.0: cannot disable port 1 (err = -19)
[11539.973491] usb 2-1: USB disconnect, address 2
[....]
mauri@mauri-laptop:~$ lspci 
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02)
00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 02)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
00:19.0 Ethernet controller: Intel Corporation 82577LC Gigabit Network Connection (rev 05)
00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05)
00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05)
00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05)
00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05)
00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5)
00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05)
00:1f.2 RAID bus controller: Intel Corporation Mobile 82801 SATA RAID Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05)
00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05)
01:00.0 VGA compatible controller: nVidia Corporation GT216 [GeForce GT 330M] (rev a2)
01:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1)
02:00.0 Network controller: Intel Corporation Centrino Advanced-N 6200 (rev 35)
03:00.0 SD Host controller: Ricoh Co Ltd Device e822
03:00.1 System peripheral: Ricoh Co Ltd Device e230
03:00.4 SD Host controller: Ricoh Co Ltd Device e822
3f:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02)
3f:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02)
3f:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02)
3f:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02)
3f:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
3f:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
mauri@mauri-laptop:~$ usb
usb-creator-gtk            usb-devices                usb_modeswitch             usb_modeswitch_dispatcher  usbmuxd                    usb_printerid              
mauri@mauri-laptop:~$ usb-devices 

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 3
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev=02.06
S:  Manufacturer=Linux 2.6.35-22-generic ehci_hcd
S:  Product=EHCI Host Controller
S:  SerialNumber=0000:00:1a.0
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=480 MxCh= 6
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=8087 ProdID=0020 Rev=00.00
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=147e ProdID=1001 Rev=00.43
S:  Manufacturer=TouchStrip        
S:  Product=Fingerprint Sensor   
C:  #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)

T:  Bus=01 Lev=02 Prnt=02 Port=01 Cnt=02 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=05ca ProdID=18b7 Rev=01.04
S:  Manufacturer=Ricoh co. Ltd.
C:  #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=0e(video) Sub=01 Prot=00 Driver=uvcvideo
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=03 Dev#=  5 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=05c6 ProdID=9224 Rev=00.02
S:  Manufacturer=Qualcomm Incorporated
S:  Product=Qualcomm Gobi 2000
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial

T:  Bus=01 Lev=02 Prnt=02 Port=05 Cnt=04 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e00f Rev=05.96
S:  Manufacturer=Broadcom Corp
S:  Product=Broadcom Bluetooth Device
S:  SerialNumber=F07BCBF85874
C:  #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 3
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1d6b ProdID=0002 Rev=02.06
S:  Manufacturer=Linux 2.6.35-22-generic ehci_hcd
S:  Product=EHCI Host Controller
S:  SerialNumber=0000:00:1d.0
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
che tipi di controlli posso fare in aggiunta?
in questo momento ad esempio non mi funziona il muose. Se riavvio torna tutto ok. Logicamente alla seconda volta...vorrei evitare di riavviare  8)
Grazie a tutti!
The day you stop upgrading your skills is the day you have actually started shrinking them

$ uname -a
Linux mauri-laptop 3.0.0-14-generic #23-Ubuntu SMP Mon Nov 21 20:28:43 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux
Scrivi risposta

Ritorna a “Driver e periferiche”

Chi c’è in linea

Visualizzano questa sezione: Google [Bot] e 10 ospiti