[Supporto] Per controllo ventole

Riconoscimento, installazione e configurazione delle periferiche.
Mark894
Prode Principiante
Messaggi: 21
Iscrizione: martedì 26 ottobre 2010, 14:05

[Supporto] Per controllo ventole

Messaggio da Mark894 »

Salve a tutti...doopo inutili tentativi decido di invocare il vostro aiuto :-[
Spiego il problema: sto cercando in tutti i modi di controllare le ventole tramite il comando

Codice: Seleziona tutto

sudo pmwonfig
, ma costantemente mi dice There are no pwm-capable sensor modules installed
logicamente ho cercato prima di tutto i sensori con

Codice: Seleziona tutto

sudo sensors-detect
e risposto yes a tutte le domande(anche a quella per far aggiungere le righe dei sensori)

La cosa che ho notato è che una volta fatte aggiungere le fighe il terminale aggiunge:
Monitoring programs won't work until the needed modules are
loaded. You may want to run '/etc/init.d/module-init-tools start'
to load them.

Unloading i2c-dev... OK
Unloading i2c-i801... OK


quello che dovrei fare è dare il comando

Codice: Seleziona tutto

etc/init.d/module-init-tools start
giusto?
Ma poi mi dice

Codice: Seleziona tutto

gianmarco@Pc-Gianmarco:~$ sudo /etc/init.d/module-init-tools start
Rather than invoking init scripts through /etc/init.d, use the service(8)
utility, e.g. service module-init-tools start

Since the script you are attempting to invoke has been converted to an
Upstart job, you may also use the start(8) utility, e.g. start module-init-tools
module-init-tools stop/waiting
che vuol dire ???
Ultima modifica di Mark894 il domenica 31 ottobre 2010, 20:24, modificato 1 volta in totale.
Avatar utente
Alka-Seltzer PLUS
Rampante Reduce
Rampante Reduce
Messaggi: 8887
Iscrizione: venerdì 18 settembre 2009, 13:29
Desktop: Unity + Gnome flashback
Distribuzione: Ubuntu 16.04 & 14.04 64bit

Re: [Supporto] Per controllo ventole

Messaggio da Alka-Seltzer PLUS »

Ciao ! Prova a dare una riavviata e poi

Codice: Seleziona tutto

sensors


per vedere quali sensori funzionano :-\
| MB: ASUS M3A78 PRO | CPU: AMD Phenom II X4 940 BE | RAM: G-SKILL 8GB 800 MHz | VGA: Sapphire ATI HD 5770 | HD: SSD SAMSUNG 850 EVO + WDC WD10EACS-00DS | Optical drive: NEC SATA AD-7201 Lightscribe | Monitor: ASUS MK221H 22' | Speakers: Majestic HTS 221 | Case: Coolermaster ELITE 335 | Power supply: EVGA SuperNova 550 GS V2 | OS: Ubuntu 16.04 64 bit + Ubuntu Linux 14.04 64bit |
Mark894
Prode Principiante
Messaggi: 21
Iscrizione: martedì 26 ottobre 2010, 14:05

Re: [Supporto] Per controllo ventole

Messaggio da Mark894 »

dando il comando

Codice: Seleziona tutto

sensors
gianmarco@Pc-Gianmarco:~$ sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0:      +55.0°C  (high = +100.0°C, crit = +100.0°C) 

coretemp-isa-0001
Adapter: ISA adapter
Core 1:      +54.0°C  (high = +100.0°C, crit = +100.0°C) 
Mark894
Prode Principiante
Messaggi: 21
Iscrizione: martedì 26 ottobre 2010, 14:05

Re: [Supporto] Per controllo ventole

Messaggio da Mark894 »

up
Ilthebest
Prode Principiante
Messaggi: 65
Iscrizione: venerdì 22 gennaio 2010, 17:17

Re: [Supporto] Per controllo ventole

Messaggio da Ilthebest »

up
ho lo stesso problema.
Avatar utente
Alka-Seltzer PLUS
Rampante Reduce
Rampante Reduce
Messaggi: 8887
Iscrizione: venerdì 18 settembre 2009, 13:29
Desktop: Unity + Gnome flashback
Distribuzione: Ubuntu 16.04 & 14.04 64bit

Re: [Supporto] Per controllo ventole

Messaggio da Alka-Seltzer PLUS »

Riportate per intero ( in codice, vedete il punto 5 delle FAQ per come fare ) il risultato di:

Codice: Seleziona tutto

sudo sensors-detect
| MB: ASUS M3A78 PRO | CPU: AMD Phenom II X4 940 BE | RAM: G-SKILL 8GB 800 MHz | VGA: Sapphire ATI HD 5770 | HD: SSD SAMSUNG 850 EVO + WDC WD10EACS-00DS | Optical drive: NEC SATA AD-7201 Lightscribe | Monitor: ASUS MK221H 22' | Speakers: Majestic HTS 221 | Case: Coolermaster ELITE 335 | Power supply: EVGA SuperNova 550 GS V2 | OS: Ubuntu 16.04 64 bit + Ubuntu Linux 14.04 64bit |
Mark894
Prode Principiante
Messaggi: 21
Iscrizione: martedì 26 ottobre 2010, 14:05

Re: [Supporto] Per controllo ventole

Messaggio da Mark894 »

ecco quanto richiesto:

Codice: Seleziona tutto

gianmarco@Pc-Gianmarco:~$ sudo sensors-detect
[sudo] password for gianmarco: 
# sensors-detect revision 5818 (2010-01-18 17:22:07 +0100)
# System: HP-Pavilion KQ521AA-ABZ IQ500.it
# Board: PEGATRON CORPORATION. EVE

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): yes
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
Intel Core family thermal sensor...                         Success!
    (driver `coretemp')
Intel Atom thermal sensor...                                No
Intel AMB FB-DIMM thermal sensor...                         No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): yes
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               Yes
Found `Asus F8000 Super IO'                                 Success!
    (address 0x295, driver `f71882fg')
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor'...                   No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No

Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no): yes
Probing for `IPMI BMC KCS' at 0xca0...                      No
Probing for `IPMI BMC SMIC' at 0xca8...                     No

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): yes
Probing for `National Semiconductor LM78' at 0x290...       No
Probing for `National Semiconductor LM79' at 0x290...       No
Probing for `Winbond W83781D' at 0x290...                   No
Probing for `Winbond W83782D' at 0x290...                   No

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): yes
Using driver `i2c-i801' for device 0000:00:1f.3: Intel 82801H ICH8
Module i2c-i801 loaded successfully.
Module i2c-dev loaded successfully.

Next adapter: NVIDIA i2c adapter  (i2c-0)
Do you want to scan it? (YES/no/selectively): yes

Next adapter: NVIDIA i2c adapter  (i2c-1)
Do you want to scan it? (YES/no/selectively): yes

Next adapter: NVIDIA i2c adapter  (i2c-2)
Do you want to scan it? (YES/no/selectively): yes

Next adapter: NVIDIA i2c adapter  (i2c-3)
Do you want to scan it? (YES/no/selectively): yes

Next adapter: SMBus I801 adapter at 0400 (i2c-4)
Do you want to scan it? (yes/NO/selectively): yes
Client found at address 0x4c
Probing for `National Semiconductor LM75'...                No
Probing for `Dallas Semiconductor DS75'...                  No
Probing for `Analog Devices ADT7466'...                     No
Probing for `Andigilog aSC7511'...                          No
Probing for `Dallas Semiconductor DS1621/DS1631'...         No
Probing for `Analog Devices ADM1021'...                     No
Probing for `Analog Devices ADM1021A/ADM1023'...            No
Probing for `Maxim MAX1617'...                              No
Probing for `Maxim MAX1617A'...                             No
Probing for `Maxim MAX1668'...                              No
Probing for `Maxim MAX1805'...                              No
Probing for `Maxim MAX1989'...                              No
Probing for `Maxim MAX6655/MAX6656'...                      No
Probing for `TI THMC10'...                                  No
Probing for `National Semiconductor LM84'...                No
Probing for `Genesys Logic GL523SM'...                      No
Probing for `Onsemi MC1066'...                              No
Probing for `Maxim MAX1618'...                              No
Probing for `Maxim MAX1619'...                              No
Probing for `National Semiconductor LM82/LM83'...           No
Probing for `National Semiconductor LM90'...                No
Probing for `National Semiconductor LM89/LM99'...           No
Probing for `National Semiconductor LM86'...                No
Probing for `Analog Devices ADM1032'...                     No
Probing for `Maxim MAX6654/MAX6690'...                      No
Probing for `Maxim MAX6657/MAX6658/MAX6659'...              No
Probing for `Maxim MAX6648/MAX6649/MAX6692'...              No
Probing for `Maxim MAX6680/MAX6681'...                      No
Probing for `Winbond W83L771W/G'...                         No
Probing for `Winbond W83L771AWG/ASG'...                     No
Probing for `Texas Instruments TMP401'...                   No
Probing for `Texas Instruments TMP411'...                   No
Probing for `Texas Instruments TMP421'...                   No
Probing for `Texas Instruments TMP422'...                   No
Probing for `Texas Instruments TMP423'...                   No
Probing for `Texas Instruments AMC6821'...                  No
Probing for `National Semiconductor LM63'...                No
Probing for `Fintek F75363SG'...                            No
Probing for `National Semiconductor LM73'...                No
Probing for `Maxim MAX6633/MAX6634/MAX6635'...              No
Probing for `Analog Devices ADT7461'...                     No
Probing for `Analog Devices ADT7481'...                     No
Probing for `Fintek F75383S/M'...                           No
Client found at address 0x50
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Yes
    (confidence 8, not a hardware monitoring chip)
Probing for `EDID EEPROM'...                                No
Client found at address 0x52
Probing for `Analog Devices ADM1033'...                     No
Probing for `Analog Devices ADM1034'...                     No
Probing for `SPD EEPROM'...                                 Yes
    (confidence 8, not a hardware monitoring chip)

Now follows a summary of the probes I have just done.
Just press ENTER to continue: 

Driver `coretemp':
  * Chip `Intel Core family thermal sensor' (confidence: 9)

Driver `f71882fg':
  * ISA bus, address 0x295
    Chip `Asus F8000 Super IO' (confidence: 9)

To load everything that is needed, add this to /etc/modules:
#----cut here----
# Chip drivers
coretemp
f71882fg
#----cut here----
If you have some drivers built into your kernel, the list above will
contain too many modules. Skip the appropriate ones!

Do you want to add these lines automatically to /etc/modules? (yes/NO)yes
Successful!

Monitoring programs won't work until the needed modules are
loaded. You may want to run '/etc/init.d/module-init-tools start'
to load them.

Unloading i2c-dev... OK
Unloading i2c-i801... OK

gianmarco@Pc-Gianmarco:~$ 
Avatar utente
Alka-Seltzer PLUS
Rampante Reduce
Rampante Reduce
Messaggi: 8887
Iscrizione: venerdì 18 settembre 2009, 13:29
Desktop: Unity + Gnome flashback
Distribuzione: Ubuntu 16.04 & 14.04 64bit

Re: [Supporto] Per controllo ventole

Messaggio da Alka-Seltzer PLUS »

Posta anche:

Codice: Seleziona tutto

cat /etc/modules
| MB: ASUS M3A78 PRO | CPU: AMD Phenom II X4 940 BE | RAM: G-SKILL 8GB 800 MHz | VGA: Sapphire ATI HD 5770 | HD: SSD SAMSUNG 850 EVO + WDC WD10EACS-00DS | Optical drive: NEC SATA AD-7201 Lightscribe | Monitor: ASUS MK221H 22' | Speakers: Majestic HTS 221 | Case: Coolermaster ELITE 335 | Power supply: EVGA SuperNova 550 GS V2 | OS: Ubuntu 16.04 64 bit + Ubuntu Linux 14.04 64bit |
Mark894
Prode Principiante
Messaggi: 21
Iscrizione: martedì 26 ottobre 2010, 14:05

Re: [Supporto] Per controllo ventole

Messaggio da Mark894 »

credo di aver dato un pò di volte il comando di aggiungere le righe per i driver ;D ;D

Codice: Seleziona tutto

gianmarco@Pc-Gianmarco:~$ cat /etc/modules
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.

lp
rtc

# Chip drivers
coretemp
f71882fg



# Generated by sensors-detect on Sun Oct 31 20:07:17 2010
# Chip drivers
coretemp
f71882fg

# Generated by sensors-detect on Mon Nov  1 09:07:12 2010
# Chip drivers
coretemp
f71882fg

# Generated by sensors-detect on Mon Nov  1 16:58:10 2010
# Chip drivers
coretemp
f71882fg
gianmarco@Pc-Gianmarco:~$ 
Avatar utente
Alka-Seltzer PLUS
Rampante Reduce
Rampante Reduce
Messaggi: 8887
Iscrizione: venerdì 18 settembre 2009, 13:29
Desktop: Unity + Gnome flashback
Distribuzione: Ubuntu 16.04 & 14.04 64bit

Re: [Supporto] Per controllo ventole

Messaggio da Alka-Seltzer PLUS »

Sì: cancella quelli in più ;D
| MB: ASUS M3A78 PRO | CPU: AMD Phenom II X4 940 BE | RAM: G-SKILL 8GB 800 MHz | VGA: Sapphire ATI HD 5770 | HD: SSD SAMSUNG 850 EVO + WDC WD10EACS-00DS | Optical drive: NEC SATA AD-7201 Lightscribe | Monitor: ASUS MK221H 22' | Speakers: Majestic HTS 221 | Case: Coolermaster ELITE 335 | Power supply: EVGA SuperNova 550 GS V2 | OS: Ubuntu 16.04 64 bit + Ubuntu Linux 14.04 64bit |
Mark894
Prode Principiante
Messaggi: 21
Iscrizione: martedì 26 ottobre 2010, 14:05

Re: [Supporto] Per controllo ventole

Messaggio da Mark894 »

facendo l'accesso da root ho cancellato quelli in più

Codice: Seleziona tutto

gianmarco@Pc-Gianmarco:~$ cat /etc/modules
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.

lp
rtc


# Generated by sensors-detect on Tue Nov  2 09:01:21 2010
# Chip drivers
coretemp
f71882fg
gianmarco@Pc-Gianmarco:~$ 

ma comunque pwmconfig non fuziona :(
Avatar utente
Alka-Seltzer PLUS
Rampante Reduce
Rampante Reduce
Messaggi: 8887
Iscrizione: venerdì 18 settembre 2009, 13:29
Desktop: Unity + Gnome flashback
Distribuzione: Ubuntu 16.04 & 14.04 64bit

Re: [Supporto] Per controllo ventole

Messaggio da Alka-Seltzer PLUS »

Hai disabilitato il controllo delle ventole da BIOS ( nel caso fosse impostato ) ?
| MB: ASUS M3A78 PRO | CPU: AMD Phenom II X4 940 BE | RAM: G-SKILL 8GB 800 MHz | VGA: Sapphire ATI HD 5770 | HD: SSD SAMSUNG 850 EVO + WDC WD10EACS-00DS | Optical drive: NEC SATA AD-7201 Lightscribe | Monitor: ASUS MK221H 22' | Speakers: Majestic HTS 221 | Case: Coolermaster ELITE 335 | Power supply: EVGA SuperNova 550 GS V2 | OS: Ubuntu 16.04 64 bit + Ubuntu Linux 14.04 64bit |
Mark894
Prode Principiante
Messaggi: 21
Iscrizione: martedì 26 ottobre 2010, 14:05

Re: [Supporto] Per controllo ventole

Messaggio da Mark894 »

il problema è proprio questo,secondo me, ma dal bios della board non c'è da nessuna parte il comando per monitorare le ventole :-\(fidati ho spulciato ovunque)
aggiornamenti per il bios li ho trovati solo sul sito hp ma necessitano windows vista(ma io in questo momento ho 7 e ubuntu)
non so che fare  ::)
Avatar utente
Alka-Seltzer PLUS
Rampante Reduce
Rampante Reduce
Messaggi: 8887
Iscrizione: venerdì 18 settembre 2009, 13:29
Desktop: Unity + Gnome flashback
Distribuzione: Ubuntu 16.04 & 14.04 64bit

Re: [Supporto] Per controllo ventole

Messaggio da Alka-Seltzer PLUS »

prova a vedere se c' è la possibilità ( sempre da BIOS ) di abilitare " ACPI " e rivela il modello esatto del computer in questione :)
| MB: ASUS M3A78 PRO | CPU: AMD Phenom II X4 940 BE | RAM: G-SKILL 8GB 800 MHz | VGA: Sapphire ATI HD 5770 | HD: SSD SAMSUNG 850 EVO + WDC WD10EACS-00DS | Optical drive: NEC SATA AD-7201 Lightscribe | Monitor: ASUS MK221H 22' | Speakers: Majestic HTS 221 | Case: Coolermaster ELITE 335 | Power supply: EVGA SuperNova 550 GS V2 | OS: Ubuntu 16.04 64 bit + Ubuntu Linux 14.04 64bit |
Mark894
Prode Principiante
Messaggi: 21
Iscrizione: martedì 26 ottobre 2010, 14:05

Re: [Supporto] Per controllo ventole

Messaggio da Mark894 »

niente da fare... :-\
Avatar utente
Alka-Seltzer PLUS
Rampante Reduce
Rampante Reduce
Messaggi: 8887
Iscrizione: venerdì 18 settembre 2009, 13:29
Desktop: Unity + Gnome flashback
Distribuzione: Ubuntu 16.04 & 14.04 64bit

Re: [Supporto] Per controllo ventole

Messaggio da Alka-Seltzer PLUS »

Alka-Seltzer PLUS ha scritto: prova a vedere se c' è la possibilità ( sempre da BIOS ) di abilitare " ACPI " e rivela il modello esatto del computer in questione :)
| MB: ASUS M3A78 PRO | CPU: AMD Phenom II X4 940 BE | RAM: G-SKILL 8GB 800 MHz | VGA: Sapphire ATI HD 5770 | HD: SSD SAMSUNG 850 EVO + WDC WD10EACS-00DS | Optical drive: NEC SATA AD-7201 Lightscribe | Monitor: ASUS MK221H 22' | Speakers: Majestic HTS 221 | Case: Coolermaster ELITE 335 | Power supply: EVGA SuperNova 550 GS V2 | OS: Ubuntu 16.04 64 bit + Ubuntu Linux 14.04 64bit |
Mark894
Prode Principiante
Messaggi: 21
Iscrizione: martedì 26 ottobre 2010, 14:05

Re: [Supporto] Per controllo ventole

Messaggio da Mark894 »

ah... scusa... non avevo capito... vuoi sapere il modello del pc? giusto?
tutte le caratteristiche le trovi qui http://h10025.www1.hp.com/ewfrf/wc/docu ... 18&lang=it
Avatar utente
Alka-Seltzer PLUS
Rampante Reduce
Rampante Reduce
Messaggi: 8887
Iscrizione: venerdì 18 settembre 2009, 13:29
Desktop: Unity + Gnome flashback
Distribuzione: Ubuntu 16.04 & 14.04 64bit

Re: [Supporto] Per controllo ventole

Messaggio da Alka-Seltzer PLUS »

Questo aggiornamento del BIOS ( per VISTA 32 bit ) pare abbia a che fare con la gestione della ventola del processore:

http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=pv-68611-1&lc=it&dlc=it&cc=it&os=2093&product=3747430&sw_lang=
| MB: ASUS M3A78 PRO | CPU: AMD Phenom II X4 940 BE | RAM: G-SKILL 8GB 800 MHz | VGA: Sapphire ATI HD 5770 | HD: SSD SAMSUNG 850 EVO + WDC WD10EACS-00DS | Optical drive: NEC SATA AD-7201 Lightscribe | Monitor: ASUS MK221H 22' | Speakers: Majestic HTS 221 | Case: Coolermaster ELITE 335 | Power supply: EVGA SuperNova 550 GS V2 | OS: Ubuntu 16.04 64 bit + Ubuntu Linux 14.04 64bit |
Mark894
Prode Principiante
Messaggi: 21
Iscrizione: martedì 26 ottobre 2010, 14:05

Re: [Supporto] Per controllo ventole

Messaggio da Mark894 »

gà l'avevo trovato questo aggiornamento il problema è che come os microsoft adesso ho windoes 7 64bit :(
Mark894
Prode Principiante
Messaggi: 21
Iscrizione: martedì 26 ottobre 2010, 14:05

Re: [Supporto] Per controllo ventole

Messaggio da Mark894 »

rischio se lo avvio io modalità compatibilità?
rettifico che anche se lo avvio in modalità compatibilità mi da errore e annulla l' update
Ultima modifica di Mark894 il martedì 2 novembre 2010, 10:01, modificato 1 volta in totale.
Scrivi risposta

Ritorna a “Driver e periferiche”

Chi c’è in linea

Visualizzano questa sezione: OMBRA_Linux e 10 ospiti